Bug#627098: linux-image-2.6.32-5-686: rndis_host fails to recognize usb device
Package: linux-2.6
Version: 2.6.32-31
Severity: normal
I'm running squeeze and I have a usb communication device that my 2.6.32-5-686
kernel doesn't recognize. The device, called a PC Port, is manufactured by
2Wire, which is now part of Pace Plc. It functions as an interface to a phone
line based network using HomePNA technology. I use a 2Wire modem/router which
is also a usb device running HomePNA, and it is recognized by rndis_host as an
eth device, but my PC Port is not.
-- Package-specific info:
** Version:
Linux version 2.6.32-5-686 (Debian 2.6.32-31) (ben@decadent.org.uk) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Tue Mar 8 21:36:00 UTC 2011
** Command line:
root=/dev/sdb2 ro acpi=off pci=noacpi BOOT_IMAGE=vmlinuz
** Not tainted
** Kernel log:
[ 6.530154] scsi target2:0:6: Beginning Domain Validation
[ 6.542446] scsi target2:0:6: Ending Domain Validation
[ 8.884195] scsi 0:0:0:0: Direct-Access ATA ST320423A 3.02 PQ: 0 ANSI: 5
[ 8.885045] scsi 0:0:1:0: Direct-Access ATA ST380021A 3.19 PQ: 0 ANSI: 5
[ 8.889551] scsi 1:0:0:0: CD-ROM _NEC DVD_RW ND-3550A 1.05 PQ: 0 ANSI: 5
[ 8.948785] usbcore: registered new interface driver hiddev
[ 8.969845] sd 0:0:0:0: [sdb] 40011300 512-byte logical blocks: (20.4 GB/19.0 GiB)
[ 8.970143] sd 0:0:0:0: [sdb] Write Protect is off
[ 8.970205] sd 0:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 8.970297] sd 0:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 8.970843] sdb:
[ 8.972468] sd 2:0:6:0: [sda] 196608 512-byte logical blocks: (100 MB/96.0 MiB)
[ 8.974295] sd 2:0:6:0: [sda] Write Protect is off
[ 8.974360] sd 2:0:6:0: [sda] Mode Sense: 31 00 00 08
[ 8.975419] sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
[ 8.975482] Uniform CD-ROM driver Revision: 3.20
[ 8.975626] sdb1 sdb2 sdb3 sdb4 <
[ 8.977076] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 8.977673] sd 2:0:6:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 8.984427] sda: sdb5
[ 8.994712] sd 0:0:1:0: [sdc] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ 9.017525] sdb6 >
[ 9.018395] sd 0:0:1:0: [sdc] Write Protect is off
[ 9.018459] sd 0:0:1:0: [sdc] Mode Sense: 00 3a 00 00
[ 9.018552] sd 0:0:1:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 9.021051] sdc: sda4
[ 9.030249] sdc1 sdc2 sdc3 sdc4 <
[ 9.030602] sd 2:0:6:0: [sda] Attached SCSI removable disk
[ 9.050326] sd 0:0:0:0: [sdb] Attached SCSI disk
[ 9.050408] sdc5 sdc6 >
[ 9.071474] sd 0:0:1:0: [sdc] Attached SCSI disk
[ 9.129991] sd 2:0:6:0: Attached scsi generic sg0 type 0
[ 9.131411] sd 0:0:0:0: Attached scsi generic sg1 type 0
[ 9.132892] sd 0:0:1:0: Attached scsi generic sg2 type 0
[ 9.134253] sr 1:0:0:0: Attached scsi generic sg3 type 5
[ 9.342853] generic-usb 0003:051D:0002.0001: hiddev0,hidraw0: USB HID v1.10 Device [APC Back-UPS ES 350 FW:823.B1.D USB FW:B1] on usb-0000:00:1d.0-2/input0
[ 9.342999] usbcore: registered new interface driver usbhid
[ 9.343061] usbhid: v2.6:USB HID core driver
[ 14.325035] udev[261]: starting version 164
[ 15.369095] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 15.562122] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 15.593819] udev[284]: renamed network interface eth1 to eth1-eth0
[ 15.603951] udev[301]: renamed network interface eth0 to eth1
[ 15.622165] intel_rng: Firmware space is locked read-only. If you can't or
[ 15.622169] intel_rng: don't want to disable this in firmware setup, and if
[ 15.622172] intel_rng: you are certain that your system has a functional
[ 15.622174] intel_rng: RNG, try using the 'no_fwh_detect' option.
[ 15.645398] udev[284]: renamed network interface eth1-eth0 to eth0
[ 16.034809] input: PC Speaker as /devices/platform/pcspkr/input/input1
[ 16.431069] i801_smbus 0000:00:1f.3: PCI->APIC IRQ transform: INT B -> IRQ 17
[ 16.433890] parport_pc 00:0c: reported by Plug and Play BIOS
[ 16.434009] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[ 16.503250] usbcore: registered new interface driver cdc_ether
[ 16.576316] eth2: register 'rndis_host' at usb-0000:00:1d.1-1, RNDIS device (poll status before control), 00:d0:9e:da:e2:02
[ 16.577198] usbcore: registered new interface driver rndis_host
[ 17.051109] cfg80211: Using static regulatory domain info
[ 17.051171] cfg80211: Regulatory domain: US
[ 17.051224] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 17.051292] (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
[ 17.051350] (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 17.051407] (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 17.051465] (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 17.051522] (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 17.051579] (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
[ 17.052449] cfg80211: Calling CRDA for country: US
[ 17.105898] usbcore: registered new interface driver rndis_wlan
[ 17.325739] input: PS/2 Logitech Mouse as /devices/platform/i8042/serio1/input/input2
[ 17.329858] udev[272]: renamed network interface eth2 to eth3
[ 17.384855] Intel ICH 0000:00:1f.5: PCI->APIC IRQ transform: INT B -> IRQ 17
[ 17.384996] Intel ICH 0000:00:1f.5: setting latency timer to 64
[ 17.824049] intel8x0_measure_ac97_clock: measured 52361 usecs (2523 samples)
[ 17.824113] intel8x0: clocking to 48000
[ 22.811441] loop: module loaded
[ 25.070476] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 25.323356] EXT2-fs warning: maximal mount count reached, running e2fsck is recommended
[ 25.385943] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 25.400644] ISO 9660 Extensions: RRIP_1991A
[ 26.476462] Bridge firewalling registered
[ 26.486272] device eth0 entered promiscuous mode
[ 26.491283] eth0: link down
[ 26.496339] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 26.505821] device eth3 entered promiscuous mode
[ 26.519896] br0: port 2(eth3) entering learning state
[ 36.748011] br0: no IPv6 routers present
[ 36.960011] eth3: no IPv6 routers present
[ 41.516013] br0: port 2(eth3) entering forwarding state
[ 42.784369] fuse init (API version 7.13)
[ 43.949444] lp0: using parport0 (interrupt-driven).
[ 43.968966] ppdev: user-space parallel port driver
[10217.760036] usb 2-1: new full speed USB device using uhci_hcd and address 3
[10217.962713] usb 2-1: New USB device found, idVendor=03f0, idProduct=3111
[10217.962768] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[10217.962817] usb 2-1: Product: officejet 4100 series
[10217.962861] usb 2-1: Manufacturer: Hewlett-Packard
[10217.962905] usb 2-1: SerialNumber: MY41CF11894Z
[10217.964866] usb 2-1: configuration #1 chosen from 1 choice
[10218.016358] usblp1: USB Bidirectional printer dev 3 if 1 alt 0 proto 2 vid 0x03F0 pid 0x3111
[10218.016481] usbcore: registered new interface driver usblp
[10254.834386] usblp1: removed
[10793.872077] usb 2-1: USB disconnect, address 3
** Model information
not available
** Loaded modules:
Module Size Used by
usblp 7899 0
ppdev 4058 0
lp 5570 0
fuse 44256 1
bridge 33019 0
stp 996 1 bridge
nls_utf8 908 1
isofs 24608 1
nls_cp437 4489 1
msdos 5118 1
fat 34912 1 msdos
loop 9765 0
snd_intel8x0 19595 0
snd_ac97_codec 79148 1 snd_intel8x0
rndis_wlan 15984 0
cfg80211 87657 1 rndis_wlan
ac97_bus 710 1 snd_ac97_codec
rfkill 10264 1 cfg80211
snd_pcm 47226 2 snd_intel8x0,snd_ac97_codec
snd_seq 35463 0
rndis_host 4359 1 rndis_wlan
snd_timer 12258 2 snd_pcm,snd_seq
cdc_ether 2633 1 rndis_host
snd_seq_device 3673 1 snd_seq
usbnet 9527 3 rndis_wlan,rndis_host,cdc_ether
i2c_i801 6462 0
parport_pc 15799 1
snd 34375 6 snd_intel8x0,snd_ac97_codec,snd_pcm,snd_seq,snd_timer,snd_seq_device
thermal_sys 9378 0
soundcore 3450 1 snd
psmouse 44809 0
pcspkr 1207 0
evdev 5609 0
parport 22554 3 ppdev,lp,parport_pc
i2c_core 12787 1 i2c_i801
snd_page_alloc 5045 2 snd_intel8x0,snd_pcm
shpchp 21220 0
serio_raw 2916 0
output 1204 0
rng_core 2178 0
pci_hotplug 18065 1 shpchp
ext2 46245 2
mbcache 3762 1 ext2
sg 15968 0
sr_mod 10770 1
sd_mod 26005 4
crc_t10dif 1012 1 sd_mod
cdrom 26487 1 sr_mod
usbhid 28008 1
ata_generic 2067 0
hid 50909 1 usbhid
uhci_hcd 16057 0
ata_piix 17736 4
8139too 14949 0
sym53c8xx 58040 0
e100 22317 0
libata 115753 2 ata_generic,ata_piix
floppy 40923 0
8139cp 13421 0
ehci_hcd 28681 0
mii 2714 4 usbnet,8139too,e100,8139cp
scsi_transport_spi 14866 1 sym53c8xx
scsi_mod 101429 6 sg,sr_mod,sd_mod,sym53c8xx,libata,scsi_transport_spi
usbcore 98733 10 usblp,rndis_wlan,rndis_host,cdc_ether,usbnet,usbhid,uhci_hcd,ehci_hcd
nls_base 4541 5 nls_utf8,isofs,nls_cp437,fat,usbcore
** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
auto br0
iface br0 inet static
address 172.16.2.1
network 172.16.0.0
netmask 255.255.0.0
broadcast 172.16.255.255
gateway 172.16.4.1
bridge_ports eth0 eth3
** Network status:
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed
lo: 660 10 0 0 0 0 0 0 660 10 0 0 0 0 0 0
eth1: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
eth0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
eth3: 8581387 26220 44 0 0 44 0 0 2469415 15915 0 0 0 0 0 0
br0: 8579745 26174 0 0 0 0 0 10683 1769155 15915 0 0 0 0 0 0
*** Protocol statistics:
Ip:
15423 total packets received
0 forwarded
0 incoming packets discarded
15410 incoming packets delivered
15422 requests sent out
Icmp:
11 ICMP messages received
0 input ICMP message failed.
ICMP input histogram:
destination unreachable: 11
0 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
IcmpMsg:
InType3: 11
Tcp:
448 active connections openings
0 passive connection openings
2 failed connection attempts
24 connection resets received
1 connections established
14080 segments received
14071 segments send out
87 segments retransmited
0 bad segments received.
164 resets sent
Udp:
1254 packets received
0 packets to unknown port received.
0 packet receive errors
1264 packets sent
UdpLite:
TcpExt:
3 TCP sockets finished time wait in fast timer
349 delayed acks sent
Quick ack mode was activated 58 times
364 packets directly queued to recvmsg prequeue.
41590 bytes directly received in process context from prequeue
9763 packet headers predicted
146 packets header predicted and directly queued to user
808 acknowledgments not containing data payload received
203 predicted acknowledgments
34 congestion windows recovered without slow start after partial ack
1 timeouts after SACK recovery
1 timeouts in loss state
24 retransmits in slow start
58 other TCP timeouts
74 DSACKs sent for old packets
21 DSACKs received
37 connections reset due to unexpected data
8 connections reset due to early user close
1 connections aborted due to timeout
TCPDSACKIgnoredOld: 1
TCPDSACKIgnoredNoUndo: 2
TCPSackShiftFallback: 10
IpExt:
InBcastPkts: 65
InOctets: 8199947
OutOctets: 1532705
InBcastOctets: 10933
*** Device features:
br0: 0x1829
eth0: 0x829
eth1: 0x0
eth3: 0x0
lo: 0x13865
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82865G/PE/P DRAM Controller/Host-Hub Interface [8086:2570] (rev 02)
Subsystem: Intel Corporation 82865G/PE/P DRAM Controller/Host-Hub Interface [8086:2570]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [e4] Vendor Specific Information: Len=06 <?>
Kernel driver in use: agpgart-intel
00:02.0 VGA compatible controller [0300]: Intel Corporation 82865G Integrated Graphics Controller [8086:2572] (rev 02) (prog-if 00 [VGA controller])
Subsystem: Intel Corporation Desktop Board D865GBF [8086:4246]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at ffa80000 (32-bit, non-prefetchable) [size=512K]
Region 2: I/O ports at ec00 [size=8]
Expansion ROM at <unassigned> [disabled]
Capabilities: [d0] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
00:06.0 System peripheral [0880]: Intel Corporation 82865G/PE/P Processor to I/O Memory Interface [8086:2576] (rev 02)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: Memory at fecf0000 (32-bit, non-prefetchable) [size=4K]
00:1d.0 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #1 [8086:24d2] (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Desktop Board D865GBF [8086:4246]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at dc00 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #2 [8086:24d4] (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Desktop Board D865GBF [8086:4246]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at e000 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #3 [8086:24d7] (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Desktop Board D865GBF [8086:4246]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at e400 [size=32]
Kernel driver in use: uhci_hcd
00:1d.3 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #4 [8086:24de] (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Desktop Board D865GBF [8086:4246]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at e800 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller [8086:24dd] (rev 02) (prog-if 20 [EHCI])
Subsystem: Intel Corporation Desktop Board D865GBF [8086:4246]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 23
Region 0: Memory at ffa7fc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME+
Capabilities: [58] Debug port: BAR=1 offset=00a0
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev c2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: ff800000-ff8fffff
Prefetchable memory behind bridge: 40000000-400fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn-
00:1f.0 ISA bridge [0601]: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC Interface Bridge [8086:24d0] (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:1f.1 IDE interface [0101]: Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE Controller [8086:24db] (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Intel Corporation Desktop Board D865GBF [8086:4246]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at ffa0 [size=16]
Region 5: Memory at 40100000 (32-bit, non-prefetchable) [size=1K]
Kernel driver in use: ata_piix
00:1f.3 SMBus [0c05]: Intel Corporation 82801EB/ER (ICH5/ICH5R) SMBus Controller [8086:24d3] (rev 02)
Subsystem: Intel Corporation Desktop Board D865GBF [8086:4246]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at d800 [size=32]
Kernel driver in use: i801_smbus
00:1f.5 Multimedia audio controller [0401]: Intel Corporation 82801EB/ER (ICH5/ICH5R) AC'97 Audio Controller [8086:24d5] (rev 02)
Subsystem: Intel Corporation Desktop Board D865GBF [8086:e001]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 2: Memory at ffa7f800 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at ffa7f400 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: Intel ICH
01:04.0 SCSI storage controller [0100]: LSI Logic / Symbios Logic 53c875 [1000:000f] (rev 04)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 72 (4250ns min, 16000ns max), Cache Line Size: 128 bytes
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at c800 [size=256]
Region 1: Memory at ff8ffc00 (32-bit, non-prefetchable) [size=256]
Region 2: Memory at ff8fe000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at 40000000 [disabled] [size=64K]
Kernel driver in use: sym53c8xx
01:05.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ [10ec:8139] (rev 10)
Subsystem: Device [3030:5032]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at c400 [size=256]
Region 1: Memory at ff8ff800 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: 8139too
01:08.0 Ethernet controller [0200]: Intel Corporation 82562EZ 10/100 Ethernet Controller [8086:1050] (rev 01)
Subsystem: Intel Corporation Desktop Board D865GBF [8086:302f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (2000ns min, 14000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 20
Region 0: Memory at ff8fd000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at cc00 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: e100
** USB devices:
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 002: ID 1630:0042
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 002: ID 051d:0002 American Power Conversion Uninterruptible Power Supply
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: 6.0.1
APT prefers stable
APT policy: (500, 'stable')
Architecture: i386 (i686)
Kernel: Linux 2.6.32-5-686 (SMP w/1 CPU core)
Locale: LANG=en_US.utf8, LC_CTYPE=en_US.utf8 (charmap=UTF-8) (ignored: LC_ALL set to en_US.utf8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-2.6.32-5-686 depends on:
ii debconf [debconf-2.0] 1.5.36.1 Debian configuration management sy
ii initramfs-tools [linux-initra 0.98.8 tools for generating an initramfs
ii linux-base 2.6.32-31 Linux image base package
ii module-init-tools 3.12-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.32-5-686 recommends:
ii firmware-linux-free 2.6.32-31 Binary firmware for various driver
ii libc6-i686 2.11.2-10 Embedded GNU C Library: Shared lib
Versions of packages linux-image-2.6.32-5-686 suggests:
ii grub-legacy [grub] 0.97-64 GRand Unified Bootloader (Legacy v
pn linux-doc-2.6.32 <none> (no description available)
Versions of packages linux-image-2.6.32-5-686 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
ii firmware-linux 0.28 Binary firmware for various driver
ii firmware-linux-nonfree 0.28 Binary firmware for various driver
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn xen-hypervisor <none> (no description available)
-- debconf information:
linux-image-2.6.32-5-686/prerm/removing-running-kernel-2.6.32-5-686: true
linux-image-2.6.32-5-686/postinst/depmod-error-initrd-2.6.32-5-686: false
linux-image-2.6.32-5-686/postinst/ignoring-do-bootloader-2.6.32-5-686:
linux-image-2.6.32-5-686/postinst/missing-firmware-2.6.32-5-686:
[ 6964.744044] usb 3-2: new full speed USB device using uhci_hcd and address 3
[ 6964.969408] usb 3-2: New USB device found, idVendor=1630, idProduct=0011
[ 6964.969474] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 6964.969533] usb 3-2: Product: 2Wire PC Port
[ 6964.969586] usb 3-2: Manufacturer: 2Wire Inc
[ 6964.970839] usb 3-2: configuration #1 chosen from 1 choice
Device: ID 1630:0042
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.01
bDeviceClass 2 Communications
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x1630
idProduct 0x0042
bcdDevice 1.00
iManufacturer 1 2Wire Inc
iProduct 2 2Wire USB Remote NDIS Ethernet
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 67
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 4 2WIREHPL
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 40mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 255 Vendor Specific (MSFT RNDIS?)
iInterface 5 ndis5
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 1
CDC Header:
bcdCDC 1.00
CDC Call Management:
bmCapabilities 0x00
bDataInterface 1
CDC ACM:
bmCapabilities 0x00
CDC Union:
bMasterInterface 0
bSlaveInterface 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 10 CDC Data
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 6 ethernet
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Device Status: 0x0001
Self Powered
Reply to: