Bug#620066: linux-image-2.6.32-5-amd64: missing firmware file cbfw.bin for module bfa.ko for Brocade Fibre Channel HBA card
Package: linux-2.6
Version: 2.6.32-31
Severity: normal
*** Please type your report below this line ***
I was install a Debian Squeeze amd64 on the next hardware:
HP Proliant ML350 G5, with 16 GB of RAM
and a HBA fibre channel card: Brocade.
Viewing the dmesg ouput:
$ dmesg | grep cbfw
[ 2.454760] bfa 0000:09:00.0: firmware: requesting cbfw.bin
[ 2.600597] Can't locate firmware cbfw.bin
[ 2.600687] bfa 0000:09:00.1: firmware: requesting cbfw.bin
[ 2.602660] Can't locate firmware cbfw.bin
and Reading the wiki page: [0] http://wiki.debian.org/Firmware
I found that I need the file: cbfw.bin for put to work my HBA Card.
Then I do a search inside Debian packages
[1] http://packages.debian.org/file%3Acbfw.bin
and I not found the file.
At the site of the provider
[2] http://www.brocade.com/forms/getFile?p=documents/downloads/HBA/Linux/Drivers/NOARCH/bfa_firmware_linux-2.3.2.3-0.src.rpm,
I can found the files:
cbfw_fc.bin, ctfw_cna.bin, ctfw_fc.bin
but, there is no the file I need,
Searching on Internet I found
[3] http://rpmfind.net/linux/RPM/fedora/14/x86_64/bfa-firmware-2.1.2.1-2.fc14.noarch.html
this rpm package have the file, but putting it to my /lib/firmware/
directory I get:
[85557.919970] scsi5 : Brocade FC/FCOE Adapter, model: Brocade-425
hwpath: 0000:09:00.1 driver: 2.0.0.0
[85559.296591] BFA[error] HAL_ASSERT: Assertion failure:
/build/buildd-linux-2.6_2.6.32-30-amd64-d4MbNM/linux-2.6-2.6.32/debian/build/source_amd64_none/drivers/scsi/bfa/bfa_fcport.c:972:
Thanks a lot for your time, and sorry for my English,
I am a Spanish speaker.
-- Package-specific info:
** Version:
Linux version 2.6.32-5-amd64 (Debian 2.6.32-31) (ben@decadent.org.uk)
(gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Mon Mar 7 21:35:22 UTC
2011
** Command line:
BOOT_IMAGE=/boot/vmlinuz-2.6.32-5-amd64
root=UUID=8259d99b-7476-414b-bd1e-00d9199e24c6 ro quiet
** Not tainted
** Kernel log:
[ 2.829960] hub 4-0:1.0: 2 ports detected
[ 2.830011] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 2.830016] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 2.830019] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 2.830027] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned
bus number 5
[ 2.830056] uhci_hcd 0000:00:1d.3: irq 19, io base 0x00001060
[ 2.830093] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.830095] usb usb5: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 2.830097] usb usb5: Product: UHCI Host Controller
[ 2.830099] usb usb5: Manufacturer: Linux 2.6.32-5-amd64 uhci_hcd
[ 2.830101] usb usb5: SerialNumber: 0000:00:1d.3
[ 2.830159] usb usb5: configuration #1 chosen from 1 choice
[ 2.830185] hub 5-0:1.0: USB hub found
[ 2.830192] hub 5-0:1.0: 2 ports detected
[ 2.830250] uhci_hcd 0000:01:04.4: PCI INT B -> GSI 22 (level, low) -> IRQ 22
[ 2.830257] uhci_hcd 0000:01:04.4: UHCI Host Controller
[ 2.830266] uhci_hcd 0000:01:04.4: new USB bus registered, assigned
bus number 6
[ 2.830278] uhci_hcd 0000:01:04.4: port count misdetected? forcing to 2 ports
[ 2.831242] uhci_hcd 0000:01:04.4: irq 22, io base 0x00003800
[ 2.831509] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.831511] usb usb6: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 2.831513] usb usb6: Product: UHCI Host Controller
[ 2.831515] usb usb6: Manufacturer: Linux 2.6.32-5-amd64 uhci_hcd
[ 2.831517] usb usb6: SerialNumber: 0000:01:04.4
[ 2.831626] usb usb6: configuration #1 chosen from 1 choice
[ 2.831658] hub 6-0:1.0: USB hub found
[ 2.831665] hub 6-0:1.0: 2 ports detected
[ 2.833687] 0000:0f:00.0: eth0: (PCI Express:2.5GB/s:Width x4)
00:1f:29:54:ca:de
[ 2.833691] 0000:0f:00.0: eth0: Intel(R) PRO/1000 Network Connection
[ 2.833767] 0000:0f:00.0: eth0: MAC: 0, PHY: 4, PBA No: d51930-004
[ 2.833802] e1000e 0000:0f:00.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 2.833820] e1000e 0000:0f:00.1: setting latency timer to 64
[ 2.833909] alloc irq_desc for 58 on node -1
[ 2.833911] alloc kstat_irqs on node -1
[ 2.833924] e1000e 0000:0f:00.1: irq 58 for MSI/MSI-X
[ 2.860947] ipmi: Found new BMC (man_id: 0x00000b, prod_id:
0x0000, dev_id: 0x11)
[ 2.860956] IPMI kcs interface initialized
[ 2.860971] ipmi_si: Trying ACPI-specified kcs state machine at i/o
address 0xca2, slave address 0x0, irq 0
[ 2.860973] ipmi_si: duplicate interface
[ 2.876554] ipmi_si 0000:01:04.6: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[ 2.876558] ipmi_si: Trying PCI-specified kcs state machine at mem
address 0xf9ef0000, slave address 0x0, irq 21
[ 2.971732] ata1.01: NODEV after polling detection
[ 2.976236] ata1.00: ATAPI: HL-DT-ST DVD-RAM GH15L, FA01, max UDMA/100
[ 2.992249] ata1.00: configured for UDMA/100
[ 2.997569] scsi 0:0:0:0: CD-ROM HL-DT-ST DVD-RAM GH15L
FA01 PQ: 0 ANSI: 5
[ 3.000533] IRQ 21/ipmi_si: IRQF_DISABLED is not guaranteed on shared IRQs
[ 3.000548] Using irq 21
[ 3.019589] 0000:0f:00.1: eth1: (PCI Express:2.5GB/s:Width x4)
00:1f:29:54:ca:df
[ 3.019592] 0000:0f:00.1: eth1: Intel(R) PRO/1000 Network Connection
[ 3.019668] 0000:0f:00.1: eth1: MAC: 0, PHY: 4, PBA No: d51930-004
[ 3.033641] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw
xa/form2 cdda tray
[ 3.033645] Uniform CD-ROM driver Revision: 3.20
[ 3.033748] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 3.070380] sr 0:0:0:0: Attached scsi generic sg0 type 5
[ 3.141298] usb 6-1: new full speed USB device using uhci_hcd and address 2
[ 3.148531] bnx2 0000:03:00.0: firmware: requesting
bnx2/bnx2-mips-06-5.0.0.j3.fw
[ 3.175074] bnx2 0000:03:00.0: firmware: requesting
bnx2/bnx2-rv2p-06-5.0.0.j3.fw
[ 3.184526] eth2: Broadcom NetXtreme II BCM5708 1000Base-T (B2)
PCI-X 64-bit 133MHz found at mem fa000000, IRQ 16, node addr
00:23:7d:3b:5f:b4
[ 3.190739] ipmi: interfacing existing BMC (man_id: 0x00000b,
prod_id: 0x0000, dev_id: 0x11)
[ 3.190758] IPMI kcs interface initialized
[ 3.287299] usb 6-1: New USB device found, idVendor=03f0, idProduct=1027
[ 3.287303] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3.287305] usb 6-1: Product: Virtual Keyboard
[ 3.287307] usb 6-1: Manufacturer: HP
[ 3.287413] usb 6-1: configuration #1 chosen from 1 choice
[ 3.382055] usbcore: registered new interface driver hiddev
[ 3.386042] input: HP Virtual Keyboard as
/devices/pci0000:00/0000:00:1e.0/0000:01:04.4/usb6/6-1/6-1:1.0/input/input3
[ 3.386119] generic-usb 0003:03F0:1027.0001: input,hidraw0: USB HID
v1.01 Keyboard [HP Virtual Keyboard] on usb-0000:01:04.4-1/input0
[ 3.392430] input: HP Virtual Keyboard as
/devices/pci0000:00/0000:00:1e.0/0000:01:04.4/usb6/6-1/6-1:1.1/input/input4
[ 3.392508] generic-usb 0003:03F0:1027.0002: input,hidraw1: USB HID
v1.01 Mouse [HP Virtual Keyboard] on usb-0000:01:04.4-1/input1
[ 3.392529] usbcore: registered new interface driver usbhid
[ 3.392532] usbhid: v2.6:USB HID core driver
[ 3.405030] usb 6-2: new full speed USB device using uhci_hcd and address 3
[ 3.555143] usb 6-2: New USB device found, idVendor=03f0, idProduct=1327
[ 3.555147] usb 6-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3.555149] usb 6-2: Product: Virtual Hub
[ 3.555151] usb 6-2: Manufacturer: HP
[ 3.555230] usb 6-2: configuration #1 chosen from 1 choice
[ 3.560663] hub 6-2:1.0: USB hub found
[ 3.562866] hub 6-2:1.0: 7 ports detected
[ 3.572413] Adding 62499832k swap on /dev/cciss/c0d0p2.
Priority:-1 extents:1 across:62499832k
[ 3.803217] loop: module loaded
[ 4.024610] EXT4-fs (cciss!c0d0p5): mounted filesystem with ordered data mode
[ 4.544281] e1000e 0000:0f:00.0: irq 57 for MSI/MSI-X
[ 4.600067] e1000e 0000:0f:00.0: irq 57 for MSI/MSI-X
[ 4.602493] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 6.161887] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow
Control: RX/TX
[ 6.161892] 0000:0f:00.0: eth0: 10/100 speed: disabling TSO
[ 6.164199] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 6.634971] alloc irq_desc for 59 on node -1
[ 6.634975] alloc kstat_irqs on node -1
[ 6.634993] bnx2 0000:03:00.0: irq 59 for MSI/MSI-X
[ 6.753778] bnx2: eth2: using MSI
[ 6.756097] ADDRCONF(NETDEV_UP): eth2: link is not ready
[ 8.772247] JBD: barrier-based sync failed on cciss!c0d0p1-8 -
disabling barriers
[ 9.927460] bnx2: eth2 NIC Copper Link is Up, 1000 Mbps full
duplex, receive & transmit flow control ON
[ 9.929827] ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready
[ 16.540022] eth0: no IPv6 routers present
[ 20.828520] eth2: no IPv6 routers present
[ 9478.816495] JBD: barrier-based sync failed on cciss!c0d0p5-8 -
disabling barriers
** Model information
sys_vendor: HP
product_name: ProLiant ML350 G5
product_version:
chassis_vendor: HP
chassis_version:
bios_vendor: HP
bios_version: D21
** Loaded modules:
Module Size Used by
kvm_intel 38146 0
kvm 214088 1 kvm_intel
loop 11799 0
usbhid 33292 0
hid 63257 1 usbhid
sg 18744 0
sr_mod 12602 0
cdrom 29415 1 sr_mod
ata_generic 3047 0
radeon 574188 0
ttm 40146 1 radeon
drm_kms_helper 20065 1 radeon
drm 142359 3 radeon,ttm,drm_kms_helper
uhci_hcd 18521 0
bfa 231363 0
i5000_edac 7284 0
i2c_algo_bit 4225 1 radeon
ipmi_si 30960 0
ehci_hcd 32081 0
edac_core 29261 3 i5000_edac
scsi_transport_fc 35355 1 bfa
ipmi_msghandler 26634 1 ipmi_si
i2c_core 15819 4 radeon,drm_kms_helper,drm,i2c_algo_bit
bnx2 57385 0
usbcore 122386 4 usbhid,uhci_hcd,ehci_hcd
scsi_tgt 8482 1 scsi_transport_fc
hpwdt 4916 0
hpilo 6268 0
i5k_amb 4439 0
ata_piix 21124 0
rng_core 3006 0
psmouse 49937 0
e1000e 110063 0
floppy 49087 0
libata 133632 2 ata_generic,ata_piix
evdev 7352 2
container 2389 0
pcspkr 1699 0
processor 29935 8
serio_raw 3752 0
button 4650 0
nls_base 6377 1 usbcore
ext4 289033 2
mbcache 5050 1 ext4
jbd2 67015 1 ext4
crc16 1319 1 ext4
cciss 83334 4
scsi_mod 122149 7
sg,sr_mod,bfa,scsi_transport_fc,scsi_tgt,libata,cciss
shpchp 26264 0
thermal 11674 0
thermal_sys 11942 2 processor,thermal
pci_hotplug 21203 1 shpchp
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 5000Z Chipset Memory
Controller Hub [8086:25d0] (rev b1)
Subsystem: Hewlett-Packard Company Device [103c:31fd]
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:02.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI
Express x8 Port 2-3 [8086:25f7] (rev b1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=0e, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: fdb00000-fddfffff
Prefetchable memory behind bridge: 00000000f8000000-00000000f81fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:03.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI
Express x4 Port 3 [8086:25e3] (rev b1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=17, subordinate=19, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:04.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI
Express x4 Port 4 [8086:25e4] (rev b1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0f, subordinate=11, sec-latency=0
I/O behind bridge: 00005000-00005fff
Memory behind bridge: fde00000-fdefffff
Prefetchable memory behind bridge: 00000000f8200000-00000000f82fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:05.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI
Express x4 Port 5 [8086:25e5] (rev b1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=12, subordinate=16, sec-latency=0
I/O behind bridge: 00006000-00006fff
Memory behind bridge: fdf00000-fdffffff
Prefetchable memory behind bridge: 00000000f8300000-00000000f83fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:10.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset FSB
Registers [8086:25f0] (rev b1)
Subsystem: Hewlett-Packard Company Device [103c:31fd]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Kernel driver in use: i5000_edac
00:10.1 Host bridge [0600]: Intel Corporation 5000 Series Chipset FSB
Registers [8086:25f0] (rev b1)
Subsystem: Hewlett-Packard Company Device [103c:31fd]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:10.2 Host bridge [0600]: Intel Corporation 5000 Series Chipset FSB
Registers [8086:25f0] (rev b1)
Subsystem: Hewlett-Packard Company Device [103c:31fd]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:11.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset
Reserved Registers [8086:25f1] (rev b1)
Subsystem: Hewlett-Packard Company Device [103c:31fd]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:13.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset
Reserved Registers [8086:25f3] (rev b1)
Subsystem: Hewlett-Packard Company Device [103c:31fd]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:15.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset FBD
Registers [8086:25f5] (rev b1)
Subsystem: Hewlett-Packard Company Device [103c:31fd]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:16.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset FBD
Registers [8086:25f6] (rev b1)
Subsystem: Hewlett-Packard Company Device [103c:31fd]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:1c.0 PCI bridge [0604]: Intel Corporation 631xESB/632xESB/3100
Chipset PCI Express Root Port 1 [8086:2690] (rev 09) (prog-if 00
[Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=03, sec-latency=0
Memory behind bridge: fa000000-fbffffff
Prefetchable memory behind bridge: 00000000f8400000-00000000f84fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB Controller [0c03]: Intel Corporation 631xESB/632xESB/3100
Chipset UHCI USB Controller #1 [8086:2688] (rev 09) (prog-if 00
[UHCI])
Subsystem: Hewlett-Packard Company Device [103c:31fe]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at 1000 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 631xESB/632xESB/3100
Chipset UHCI USB Controller #2 [8086:2689] (rev 09) (prog-if 00
[UHCI])
Subsystem: Hewlett-Packard Company Device [103c:31fe]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at 1020 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 631xESB/632xESB/3100
Chipset UHCI USB Controller #3 [8086:268a] (rev 09) (prog-if 00
[UHCI])
Subsystem: Hewlett-Packard Company Device [103c:31fe]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 1040 [size=32]
Kernel driver in use: uhci_hcd
00:1d.3 USB Controller [0c03]: Intel Corporation 631xESB/632xESB/3100
Chipset UHCI USB Controller #4 [8086:268b] (rev 09) (prog-if 00
[UHCI])
Subsystem: Hewlett-Packard Company Device [103c:31fe]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 19
Region 4: I/O ports at 1060 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 631xESB/632xESB/3100
Chipset EHCI USB2 Controller [8086:268c] (rev 09) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Device [103c:31fe]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f9df0000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge
[8086:244e] (rev d9) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 00002000-00003fff
Memory behind bridge: f9e00000-f9ffffff
Prefetchable memory behind bridge: 00000000f0000000-00000000f7ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 631xESB/632xESB/3100
Chipset LPC Interface Controller [8086:2670] (rev 09)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:1f.2 IDE interface [0101]: Intel Corporation 631xESB/632xESB/3100
Chipset SATA IDE Controller [8086:2680] (rev 09) (prog-if 80 [Master])
Subsystem: Compaq Computer Corporation Device [0e11:3201]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 0500 [size=16]
Capabilities: <access denied>
Kernel driver in use: ata_piix
01:03.0 VGA compatible controller [0300]: ATI Technologies Inc ES1000
[1002:515e] (rev 02) (prog-if 00 [VGA controller])
Subsystem: Hewlett-Packard Company Device [103c:31fb]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (2000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 3000 [size=256]
Region 2: Memory at f9ff0000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at f9e00000 [disabled] [size=128K]
Capabilities: <access denied>
01:04.0 System peripheral [0880]: Compaq Computer Corporation
Integrated Lights Out Controller [0e11:b203] (rev 03)
Subsystem: Hewlett-Packard Company Device [103c:3305]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at 2800 [size=256]
Region 1: Memory at f9fe0000 (32-bit, non-prefetchable) [size=512]
Capabilities: <access denied>
Kernel driver in use: hpwdt
01:04.2 System peripheral [0880]: Compaq Computer Corporation
Integrated Lights Out Processor [0e11:b204] (rev 03)
Subsystem: Hewlett-Packard Company Device [103c:3305]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 22
BIST result: 00
Region 0: I/O ports at 3400 [size=256]
Region 1: Memory at f9fd0000 (32-bit, non-prefetchable) [size=2K]
Region 2: Memory at f9fc0000 (32-bit, non-prefetchable) [size=8K]
Region 3: Memory at f9f00000 (32-bit, non-prefetchable) [size=512K]
[virtual] Expansion ROM at f9e20000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: hpilo
01:04.4 USB Controller [0c03]: Hewlett-Packard Company Proliant
iLO2/iLO3 virtual USB controller [103c:3300] (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:3305]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin B routed to IRQ 22
Region 4: I/O ports at 3800 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
01:04.6 IPMI SMIC interface [0c07]: Hewlett-Packard Company Proliant
iLO2 virtual UART [103c:3302] (prog-if 01)
Subsystem: Hewlett-Packard Company Device [103c:3305]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 21
Region 0: Memory at f9ef0000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ipmi_si
02:00.0 PCI bridge [0604]: Broadcom EPB PCI-Express to PCI-X Bridge
[1166:0103] (rev c3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=02, secondary=03, subordinate=03, sec-latency=64
Memory behind bridge: fa000000-fbffffff
Prefetchable memory behind bridge: 00000000f8400000-00000000f84fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
03:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme II
BCM5708 Gigabit Ethernet [14e4:164c] (rev 12)
Subsystem: Hewlett-Packard Company NC373i Integrated Multifunction
Gigabit Server Adapter [103c:7038]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (16000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 59
Region 0: Memory at fa000000 (64-bit, non-prefetchable) [size=32M]
[virtual] Expansion ROM at f8400000 [disabled] [size=2K]
Capabilities: <access denied>
Kernel driver in use: bnx2
04:00.0 PCI bridge [0604]: Intel Corporation 6311ESB/6321ESB PCI
Express Upstream Port [8086:3500] (rev 01) (prog-if 00 [Normal
decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=04, secondary=05, subordinate=0b, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: fdc00000-fddfffff
Prefetchable memory behind bridge: 00000000f8000000-00000000f81fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
04:00.3 PCI bridge [0604]: Intel Corporation 6311ESB/6321ESB PCI
Express to PCI-X Bridge [8086:350c] (rev 01) (prog-if 00 [Normal
decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=04, secondary=0c, subordinate=0e, sec-latency=64
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
05:00.0 PCI bridge [0604]: Intel Corporation 6311ESB/6321ESB PCI
Express Downstream Port E1 [8086:3510] (rev 01) (prog-if 00 [Normal
decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=05, secondary=06, subordinate=08, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: fdc00000-fdcfffff
Prefetchable memory behind bridge: 00000000f8000000-00000000f80fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
05:01.0 PCI bridge [0604]: Intel Corporation 6311ESB/6321ESB PCI
Express Downstream Port E2 [8086:3514] (rev 01) (prog-if 00 [Normal
decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=05, secondary=09, subordinate=0b, sec-latency=0
Memory behind bridge: fdd00000-fddfffff
Prefetchable memory behind bridge: 00000000f8100000-00000000f81fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
06:00.0 PCI bridge [0604]: Broadcom EPB PCI-Express to PCI-X Bridge
[1166:0103] (rev b4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=06, secondary=07, subordinate=08, sec-latency=64
I/O behind bridge: 00004000-00004fff
Memory behind bridge: fdc00000-fdcfffff
Prefetchable memory behind bridge: 00000000f8000000-00000000f80fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
07:04.0 PCI bridge [0604]: Broadcom BCM5785 [HT1000] PCI/PCI-X Bridge
[1166:0104] (rev b2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Bus: primary=07, secondary=08, subordinate=08, sec-latency=64
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
07:08.0 RAID bus controller [0104]: Hewlett-Packard Company Smart
Array E200i (SAS Controller) [103c:3238]
Subsystem: Hewlett-Packard Company Smart Array E200 [103c:3212]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr+ DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR+ INTx-
Latency: 64
Interrupt: pin A routed to IRQ 55
Region 0: Memory at fdc80000 (64-bit, non-prefetchable) [size=512K]
Region 2: I/O ports at 4000 [size=256]
Region 3: Memory at fdc70000 (32-bit, non-prefetchable) [size=32K]
[virtual] Expansion ROM at f8000000 [disabled] [size=16K]
Capabilities: <access denied>
Kernel driver in use: cciss
09:00.0 Fibre Channel [0c04]: Brocade Communications Systems, Inc.
425/825/42B/82B 4Gbps/8Gbps PCIe dual port FC HBA [1657:0013] (rev 01)
Subsystem: Hewlett-Packard Company HP 42B 4Gbps dual port FC HBA [103c:1744]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 7
Region 0: Memory at fdde0000 (64-bit, non-prefetchable) [size=128K]
Region 2: Memory at fddd0000 (64-bit, non-prefetchable) [size=16K]
[virtual] Expansion ROM at f8100000 [disabled] [size=512K]
Capabilities: <access denied>
09:00.1 Fibre Channel [0c04]: Brocade Communications Systems, Inc.
425/825/42B/82B 4Gbps/8Gbps PCIe dual port FC HBA [1657:0013] (rev 01)
Subsystem: Hewlett-Packard Company HP 42B 4Gbps dual port FC HBA [103c:1744]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 10
Region 0: Memory at fdda0000 (64-bit, non-prefetchable) [size=128K]
Region 2: Memory at fdd90000 (64-bit, non-prefetchable) [size=16K]
[virtual] Expansion ROM at f8180000 [disabled] [size=512K]
Capabilities: <access denied>
0f:00.0 Ethernet controller [0200]: Intel Corporation 82571EB Gigabit
Ethernet Controller [8086:105e] (rev 06)
Subsystem: Hewlett-Packard Company NC360T PCI Express Dual Port
Gigabit Server Adapter [103c:7044]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 57
Region 0: Memory at fdee0000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at fdec0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 5000 [size=32]
[virtual] Expansion ROM at f8200000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: e1000e
0f:00.1 Ethernet controller [0200]: Intel Corporation 82571EB Gigabit
Ethernet Controller [8086:105e] (rev 06)
Subsystem: Hewlett-Packard Company NC360T PCI Express Dual Port
Gigabit Server Adapter [103c:7044]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 58
Region 0: Memory at fdea0000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at fde80000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 5020 [size=32]
[virtual] Expansion ROM at f8220000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: e1000e
12:00.0 PCI bridge [0604]: Broadcom EPB PCI-Express to PCI-X Bridge
[1166:0103] (rev b4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=12, secondary=13, subordinate=16, sec-latency=64
I/O behind bridge: 00006000-00006fff
Memory behind bridge: fdf00000-fdffffff
Prefetchable memory behind bridge: 00000000f8300000-00000000f83fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
13:04.0 PCI bridge [0604]: Broadcom BCM5785 [HT1000] PCI/PCI-X Bridge
[1166:0104] (rev b2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Bus: primary=13, secondary=14, subordinate=16, sec-latency=64
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
13:08.0 RAID bus controller [0104]: Hewlett-Packard Company Smart
Array E200i (SAS Controller) [103c:3238]
Subsystem: Hewlett-Packard Company Smart Array E200i [103c:3211]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin A routed to IRQ 56
Region 0: Memory at fdf80000 (64-bit, non-prefetchable) [size=512K]
Region 2: I/O ports at 6000 [size=256]
Region 3: Memory at fdf70000 (32-bit, non-prefetchable) [size=32K]
[virtual] Expansion ROM at f8300000 [disabled] [size=16K]
Capabilities: <access denied>
Kernel driver in use: cciss
** Sound cards:
-- System Information:
Debian Release: 6.0.1
APT prefers stable
APT policy: (500, 'stable')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.32-5-amd64 (SMP w/8 CPU cores)
Locale: LANG=es_PY.UTF-8, LC_CTYPE=es_PY.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-2.6.32-5-amd64 depends on:
ii debconf [debconf-2.0] 1.5.36.1 Debian configuration management sy
ii initramfs-tools [linux-initra 0.98.8 tools for generating an initramfs
ii linux-base 2.6.32-31 Linux image base package
ii module-init-tools 3.12-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.32-5-amd64 recommends:
pn firmware-linux-free <none> (no description available)
Versions of packages linux-image-2.6.32-5-amd64 suggests:
pn grub | lilo <none> (no description available)
pn linux-doc-2.6.32 <none> (no description available)
Versions of packages linux-image-2.6.32-5-amd64 is related to:
ii firmware-bnx2 0.28 Binary firmware for Broadcom NetXt
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-linux <none> (no description available)
pn firmware-linux-nonfree <none> (no description available)
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn xen-hypervisor <none> (no description available)
-- debconf-show failed
--
§~^Calabaza^~§ from Barrio Obrero, Asunción, Paraguay
http://es.wikipedia.org/wiki/Top-posting
http://es.wikipedia.org/wiki/Netiquette
Reply to: