Bug#619504: linux-image-2.6.32-5-686: Thermal trip points insanely low Package: linux-2.6 Version: 2.6.32-31 Severity: important
Package: linux-2.6
Version: 2.6.32-31
Severity: important
On boot, thermal trip points are set to the following:
cat /proc/acpi/thermal_zone/TZ1/trip_points
critical (S5): 105 C
passive: 16 C: tc1=1 tc2=2 tsp=100 devices=CPU0 CPU1
active[0]: 16 C: devices=C39B
active[1]: 16 C: devices=C39C
active[2]: 16 C: devices=C39D
active[3]: 16 C: devices=C39E
This causes the CPU to constantly clock down to 800MHz, making the system unusably slow. I have encountered this problem
in previous kernels until 2 or 3 years ago, at which point it was fixed (I believe by adding this laptop model to some
sort of ACPI black list). Recent upgrade re-introduced the bug. Laptop model is HP Compaq 6715s.
-- Package-specific info:
** Version:
Linux version 2.6.32-5-686 (Debian 2.6.32-31) (ben@decadent.org.uk) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Tue Mar 8 21:36:00 UTC 2011
** Command line:
BOOT_IMAGE=/vmlinuz-2.6.32-5-686 root=/dev/mapper/twisted-root ro quiet
** Not tainted
** Kernel log:
[ 73.304899] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:14.2/input/input7
[ 73.462294] Bluetooth: Generic Bluetooth USB driver ver 0.6
[ 73.462948] usbcore: registered new interface driver btusb
[ 74.640155] EXT3 FS on dm-1, internal journal
[ 75.027200] loop: module loaded
[ 75.756848] Adding 1765368k swap on /dev/mapper/twisted-swap_1. Priority:-1 extents:1 across:1765368k
[ 76.517349] kjournald starting. Commit interval 5 seconds
[ 76.520286] EXT3 FS on dm-3, internal journal
[ 76.520295] EXT3-fs: mounted filesystem with ordered data mode.
[ 77.815115] fuse init (API version 7.13)
[ 79.167033] vboxdrv: Found 2 processor cores.
[ 79.167618] vboxdrv: fAsync=1 offMin=0x5f86c offMax=0x5f86c
[ 79.168156] vboxdrv: TSC mode is 'asynchronous', kernel timer mode is 'normal'.
[ 79.168160] vboxdrv: Successfully loaded version 4.0.2_OSE (interface 0x00160000).
[ 79.637978] input: ACPI Virtual Keyboard Device as /devices/virtual/input/input8
[ 82.022423] tg3 0000:10:00.0: irq 27 for MSI/MSI-X
[ 82.068430] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 82.128078] b43 ssb0:0: firmware: requesting b43/ucode13.fw
[ 82.217695] b43 ssb0:0: firmware: requesting b43/b0g0initvals13.fw
[ 82.424072] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[ 82.528761] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 84.149898] apm: BIOS not found.
[ 85.259613] Bluetooth: L2CAP ver 2.14
[ 85.259617] Bluetooth: L2CAP socket layer initialized
[ 85.280744] Bluetooth: RFCOMM TTY layer initialized
[ 85.280758] Bluetooth: RFCOMM socket layer initialized
[ 85.280766] Bluetooth: RFCOMM ver 1.11
[ 85.592041] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 85.592045] Bluetooth: BNEP filters: protocol multicast
[ 85.604129] Bluetooth: SCO (Voice Link) ver 0.6
[ 85.604132] Bluetooth: SCO socket layer initialized
[ 86.339563] pci 0000:01:05.0: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 86.602441] lp: driver loaded but no devices found
[ 86.680568] [drm] Initialized drm 1.1.0 20060810
[ 86.682366] ppdev: user-space parallel port driver
[ 87.062425] [drm] radeon kernel modesetting enabled.
[ 87.065394] [drm] radeon: Initializing kernel modesetting.
[ 87.065506] [drm] register mmio base: 0xD0200000
[ 87.065509] [drm] register mmio size: 65536
[ 87.065652] ATOM BIOS: ATI
[ 87.065872] [drm] GPU reset succeed (RBBM_STATUS=0x10000140)
[ 87.065896] [drm] radeon: VRAM 128M
[ 87.065898] [drm] radeon: VRAM from 0x38000000 to 0x3FFFFFFF
[ 87.065900] [drm] radeon: GTT 512M
[ 87.065902] [drm] radeon: GTT from 0x40000000 to 0x5FFFFFFF
[ 87.065957] [drm] radeon: irq initialized.
[ 87.066161] [drm] Detected VRAM RAM=128M, BAR=128M
[ 87.066173] [drm] RAM width 128bits DDR
[ 87.066306] [TTM] Zone kernel: Available graphics memory: 446066 kiB.
[ 87.066311] [TTM] Zone highmem: Available graphics memory: 452054 kiB.
[ 87.066339] [drm] radeon: 128M of VRAM memory ready
[ 87.066342] [drm] radeon: 512M of GTT memory ready.
[ 87.066367] [drm] GART: num cpu pages 131072, num gpu pages 131072
[ 87.070819] [drm] radeon: 1 quad pipes, 1 z pipes initialized.
[ 87.070841] [drm] radeon: cp idle (0x10000C03)
[ 87.070902] [drm] Loading RS690/RS740 Microcode
[ 87.070905] platform radeon_cp.0: firmware: requesting radeon/RS690_cp.bin
[ 87.114807] [drm] radeon: ring at 0x0000000040000000
[ 87.114828] [drm] ring test succeeded in 1 usecs
[ 87.115007] [drm] radeon: ib pool ready.
[ 87.115099] [drm] ib test succeeded in 0 usecs
[ 87.115294] [drm] Default TV standard: NTSC
[ 87.115333] [drm] Radeon Display Connectors
[ 87.115336] [drm] Connector 0:
[ 87.115338] [drm] VGA
[ 87.115341] [drm] DDC: 0x7e50 0x7e40 0x7e54 0x7e44 0x7e58 0x7e48 0x7e5c 0x7e4c
[ 87.115343] [drm] Encoders:
[ 87.115346] [drm] CRT1: INTERNAL_KLDSCP_DAC1
[ 87.115348] [drm] Connector 1:
[ 87.115350] [drm] LVDS
[ 87.115358] [drm] DDC: 0x7e40 0x7e50 0x7e44 0x7e54 0x7e48 0x7e58 0x7e4c 0x7e5c
[ 87.115361] [drm] Encoders:
[ 87.115363] [drm] LCD1: INTERNAL_LVTM1
[ 87.115365] [drm] Connector 2:
[ 87.115367] [drm] S-video
[ 87.115368] [drm] Encoders:
[ 87.115370] [drm] TV1: INTERNAL_KLDSCP_DAC1
[ 87.794783] [drm] fb mappable at 0xC0040000
[ 87.794787] [drm] vram apper at 0xC0000000
[ 87.794789] [drm] size 4096000
[ 87.794791] [drm] fb depth is 24
[ 87.794793] [drm] pitch is 5120
[ 87.795147] Console: switching to colour frame buffer device 160x50
[ 87.795161] fb0: radeondrmfb frame buffer device
[ 87.795164] registered panic notifier
[ 87.795170] [drm] Initialized radeon 2.0.0 20080528 for 0000:01:05.0 on minor 0
[ 89.533202] powernow-k8: Found 1 AMD Turion(tm) 64 X2 Mobile Technology TL-56 processors (2 cpu cores) (version 2.20.00)
[ 89.533265] powernow-k8: 0 : fid 0xa (1800 MHz), vid 0x13
[ 89.533269] powernow-k8: 1 : fid 0x8 (1600 MHz), vid 0x15
[ 89.533272] powernow-k8: 2 : fid 0x0 (800 MHz), vid 0x1e
[ 90.193052] Clocksource tsc unstable (delta = -278026318 ns)
[ 130.268076] wlan0: direct probe to AP 00:13:10:02:62:b7 (try 1)
[ 130.270269] wlan0: direct probe responded
[ 130.270281] wlan0: authenticate with AP 00:13:10:02:62:b7 (try 1)
[ 130.274068] wlan0: authenticated
[ 130.274144] wlan0: associate with AP 00:13:10:02:62:b7 (try 1)
[ 130.278936] wlan0: RX AssocResp from 00:13:10:02:62:b7 (capab=0x411 status=0 aid=3)
[ 130.278948] wlan0: associated
[ 130.281187] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 141.173041] wlan0: no IPv6 routers present
** Model information
not available
** Loaded modules:
Module Size Used by
powernow_k8 9832 1
cpufreq_userspace 1480 0
cpufreq_stats 1940 0
cpufreq_powersave 602 0
cpufreq_conservative 4018 0
radeon 511144 1
ttm 33494 1 radeon
drm_kms_helper 18309 1 radeon
parport_pc 15799 0
ppdev 4058 0
drm 112088 3 radeon,ttm,drm_kms_helper
lp 5570 0
parport 22554 3 parport_pc,ppdev,lp
i2c_algo_bit 3497 1 radeon
sco 5857 2
bnep 7444 2
rfcomm 25175 8
l2cap 21709 16 bnep,rfcomm
crc16 1027 1 l2cap
vboxnetadp 5254 0
vboxnetflt 15376 0
vboxdrv 143929 2 vboxnetadp,vboxnetflt
binfmt_misc 4907 1
uinput 4796 1
fuse 44256 1
ext2 46245 1
loop 9765 0
btusb 8077 2
snd_hda_codec_analog 45530 1
arc4 974 2
snd_hda_intel 16823 1
snd_hda_codec 46002 2 snd_hda_codec_analog,snd_hda_intel
bluetooth 36319 9 sco,bnep,rfcomm,l2cap,btusb
ecb 1405 2
snd_hwdep 4054 1 snd_hda_codec
snd_pcm 47226 2 snd_hda_intel,snd_hda_codec
b43 132615 0
joydev 6739 0
snd_seq 35463 0
snd_timer 12258 2 snd_pcm,snd_seq
snd_seq_device 3673 1 snd_seq
rng_core 2178 1 b43
mac80211 123570 1 b43
cfg80211 87657 2 b43,mac80211
snd 34375 10 snd_hda_codec_analog,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_seq,snd_timer,snd_seq_device
psmouse 44809 0
rfkill 10264 4 bluetooth,cfg80211
pcspkr 1207 0
k8temp 2551 0
soundcore 3450 1 snd
yenta_socket 16403 1
rsrc_nonstatic 7057 1 yenta_socket
shpchp 21220 0
snd_page_alloc 5045 2 snd_hda_intel,snd_pcm
video 14605 0
output 1204 1 video
evdev 5609 13
serio_raw 2916 0
pci_hotplug 18065 1 shpchp
i2c_piix4 7076 0
led_class 1757 1 b43
wmi 3575 0
i2c_core 12787 5 radeon,drm_kms_helper,drm,i2c_algo_bit,i2c_piix4
container 1833 0
battery 3782 0
processor 26327 1 powernow_k8
button 3598 0
ac 1640 0
ext3 94204 2
jbd 32169 1 ext3
mbcache 3762 2 ext2,ext3
sha256_generic 10748 2
aes_i586 6816 3
aes_generic 25738 1 aes_i586
cbc 2047 1
dm_crypt 9264 1
dm_mod 46046 12 dm_crypt
sg 15968 0
sd_mod 26005 3
crc_t10dif 1012 1 sd_mod
sr_mod 10770 0
cdrom 26487 1 sr_mod
ata_generic 2067 0
ssb 33714 1 b43
fan 2586 0
mmc_core 38665 2 b43,ssb
pcmcia 16194 2 b43,ssb
thermal 9206 0
tg3 88273 0
pata_atiixp 2541 0
ahci 27270 2
pcmcia_core 20450 5 b43,yenta_socket,rsrc_nonstatic,ssb,pcmcia
libphy 11638 1 tg3
thermal_sys 9378 4 video,processor,fan,thermal
ohci_hcd 16987 0
ehci_hcd 28681 0
libata 115753 3 ata_generic,pata_atiixp,ahci
usbcore 98733 4 btusb,ohci_hcd,ehci_hcd
nls_base 4541 1 usbcore
scsi_mod 101429 4 sg,sd_mod,sr_mod,libata
** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
allow-hotplug eth0
#iface eth0 inet dhcp
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN qlen 1000
link/ether 00:1a:4b:5d:53:3d brd ff:ff:ff:ff:ff:ff
3: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000
link/ether 00:1a:73:6f:49:13 brd ff:ff:ff:ff:ff:ff
inet 10.100.0.142/24 brd 10.100.0.255 scope global wlan0
inet6 fe80::21a:73ff:fe6f:4913/64 scope link
valid_lft forever preferred_lft forever
4: vboxnet0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
link/ether 0a:00:27:00:00:00 brd ff:ff:ff:ff:ff:ff
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed
lo: 262066 604 0 0 0 0 0 0 262066 604 0 0 0 0 0 0
eth0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
wlan0: 940747 1427 0 0 0 0 0 0 250580 1098 0 0 0 0 0 0
vboxnet0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
*** Protocol statistics:
Ip:
2066 total packets received
1 with invalid addresses
0 forwarded
0 incoming packets discarded
2025 incoming packets delivered
1670 requests sent out
8 dropped because of missing route
Icmp:
0 ICMP messages received
0 input ICMP message failed.
ICMP input histogram:
0 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
Tcp:
91 active connections openings
19 passive connection openings
43 failed connection attempts
6 connection resets received
4 connections established
1654 segments received
1517 segments send out
28 segments retransmited
0 bad segments received.
52 resets sent
Udp:
223 packets received
0 packets to unknown port received.
0 packet receive errors
123 packets sent
UdpLite:
TcpExt:
13 TCP sockets finished time wait in fast timer
54 delayed acks sent
604 packet headers predicted
330 acknowledgments not containing data payload received
83 predicted acknowledgments
4 congestion windows recovered without slow start after partial ack
10 other TCP timeouts
3 DSACKs received
2 connections reset due to unexpected data
4 connections reset due to early user close
1 connections aborted due to timeout
TCPDSACKIgnoredOld: 2
IpExt:
InMcastPkts: 42
OutMcastPkts: 11
InBcastPkts: 304
OutBcastPkts: 88
InOctets: 1189354
OutOctets: 473770
InMcastOctets: 8351
OutMcastOctets: 2480
InBcastOctets: 39789
OutBcastOctets: 12056
*** Device features:
eth0: 0x9a3
lo: 0x13865
vboxnet0: 0x0
wlan0: 0x2000
** PCI devices:
00:00.0 Host bridge [0600]: ATI Technologies Inc RS690 Host Bridge [1002:7910]
Subsystem: Hewlett-Packard Company Device [103c:30c2]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 64
00:01.0 PCI bridge [0604]: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx) [1002:7912] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: d0200000-d03fffff
Prefetchable memory behind bridge: 00000000c0000000-00000000c7ffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:04.0 PCI bridge [0604]: ATI Technologies Inc Device [1002:7914] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=10, subordinate=10, sec-latency=0
Memory behind bridge: d0000000-d00fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:05.0 PCI bridge [0604]: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 1) [1002:7915] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=20, subordinate=20, sec-latency=0
I/O behind bridge: 00002000-00003fff
Memory behind bridge: cc000000-cfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:06.0 PCI bridge [0604]: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 2) [1002:7916] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=30, subordinate=30, sec-latency=0
Memory behind bridge: c8000000-c80fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:12.0 SATA controller [0106]: ATI Technologies Inc SB600 Non-Raid-5 SATA [1002:4380] (prog-if 01 [AHCI 1.0])
Subsystem: ATI Technologies Inc SB600 Non-Raid-5 SATA [1002:4380]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 9000 [size=8]
Region 1: I/O ports at 9008 [size=4]
Region 2: I/O ports at 9010 [size=8]
Region 3: I/O ports at 5018 [size=4]
Region 4: I/O ports at 5020 [size=16]
Region 5: Memory at d0409000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:13.0 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI0) [1002:4387] (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company Device [103c:30c2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 23
Region 0: Memory at d0401000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:13.1 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI1) [1002:4388] (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company Device [103c:30c2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at d0402000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:13.2 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI2) [1002:4389] (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company Device [103c:30c2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 17
Region 0: Memory at d0403000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:13.3 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI3) [1002:438a] (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company Device [103c:30c2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at d0404000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:13.4 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI4) [1002:438b] (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company Device [103c:30c2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 17
Region 0: Memory at d0405000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:13.5 USB Controller [0c03]: ATI Technologies Inc SB600 USB Controller (EHCI) [1002:4386] (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Device [103c:30c2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin D routed to IRQ 23
Region 0: Memory at d0406000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:14.0 SMBus [0c05]: ATI Technologies Inc SBx00 SMBus Controller [1002:4385] (rev 14)
Subsystem: Hewlett-Packard Company Device [103c:30c2]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: I/O ports at 8200 [size=16]
Capabilities: <access denied>
Kernel driver in use: piix4_smbus
00:14.1 IDE interface [0101]: ATI Technologies Inc SB600 IDE [1002:438c] (prog-if 82 [Master PriP])
Subsystem: Hewlett-Packard Company Device [103c:30c2]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 5040 [size=16]
Kernel driver in use: pata_atiixp
00:14.2 Audio device [0403]: ATI Technologies Inc SBx00 Azalia (Intel HDA) [1002:4383]
Subsystem: Hewlett-Packard Company Device [103c:30c2]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin ? routed to IRQ 16
Region 0: Memory at 44000000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
00:14.3 ISA bridge [0601]: ATI Technologies Inc SB600 PCI to LPC Bridge [1002:438d]
Subsystem: Hewlett-Packard Company Device [103c:30c2]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:14.4 PCI bridge [0604]: ATI Technologies Inc SBx00 PCI to PCI Bridge [1002:4384] (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=02, subordinate=06, sec-latency=64
I/O behind bridge: 00001000-00001fff
Memory behind bridge: d0100000-d01fffff
Prefetchable memory behind bridge: 40000000-43ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map [1022:1101]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller [1022:1102]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control [1022:1103]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
Kernel driver in use: k8temp
01:05.0 VGA compatible controller [0300]: ATI Technologies Inc RS690M [Radeon X1200 Series] [1002:791f] (prog-if 00 [VGA controller])
Subsystem: Hewlett-Packard Company Device [103c:30c2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 19
Region 0: Memory at c0000000 (64-bit, prefetchable) [size=128M]
Region 2: Memory at d0200000 (64-bit, non-prefetchable) [size=64K]
Region 4: I/O ports at 4000 [size=256]
Region 5: Memory at d0300000 (32-bit, non-prefetchable) [size=1M]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: radeon
02:04.0 CardBus bridge [0607]: Ricoh Co Ltd RL5c476 II [1180:0476] (rev b6)
Subsystem: Hewlett-Packard Company Device [103c:30c2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168
Interrupt: pin A routed to IRQ 20
Region 0: Memory at d0100000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
Memory window 0: 40000000-43fff000 (prefetchable)
Memory window 1: 48000000-4bfff000
I/O window 0: 00001000-000010ff
I/O window 1: 00001400-000014ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
10:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM5906M Fast Ethernet PCI Express [14e4:1713] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:30c2]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 27
Region 0: Memory at d0000000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at <ignored> [disabled]
Capabilities: <access denied>
Kernel driver in use: tg3
30:00.0 Network controller [0280]: Broadcom Corporation BCM4311 802.11a/b/g [14e4:4312] (rev 02)
Subsystem: Hewlett-Packard Company Broadcom 802.11a/b/g WLAN [103c:1371]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at c8000000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: b43-pci-bridge
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 002: ID 03f0:171d Hewlett-Packard Wireless (Bluetooth + WLAN) Interface [Integrated Module]
-- System Information:
Debian Release: wheezy/sid
APT prefers testing
APT policy: (990, 'testing'), (500, 'squeeze-updates'), (500, 'stable'), (300, 'unstable')
Architecture: i386 (i686)
Kernel: Linux 2.6.32-5-686 (SMP w/2 CPU cores)
Locale: LANG=en_IE.utf8, LC_CTYPE=en_IE.utf8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-2.6.32-5-686 depends on:
ii debconf [debconf-2.0] 1.5.38 Debian configuration management sy
ii initramfs-tools [linux-initra 0.98.8 tools for generating an initramfs
ii linux-base 2.6.32-31 Linux image base package
ii module-init-tools 3.12-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.32-5-686 recommends:
ii firmware-linux-free 2.6.32-31 Binary firmware for various driver
ii libc6-i686 2.11.2-11 Embedded GNU C Library: Shared lib
Versions of packages linux-image-2.6.32-5-686 suggests:
pn grub | lilo <none> (no description available)
pn linux-doc-2.6.32 <none> (no description available)
Versions of packages linux-image-2.6.32-5-686 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
ii firmware-linux 0.29 Binary firmware for various driver
ii firmware-linux-nonfree 0.29 Binary firmware for various driver
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn xen-hypervisor <none> (no description available)
-- debconf information:
linux-image-2.6.32-5-686/prerm/removing-running-kernel-2.6.32-5-686: true
linux-image-2.6.32-5-686/postinst/depmod-error-initrd-2.6.32-5-686: false
linux-image-2.6.32-5-686/postinst/ignoring-do-bootloader-2.6.32-5-686:
linux-image-2.6.32-5-686/postinst/missing-firmware-2.6.32-5-686:
Reply to: