Bug#615397: linux-image-2.6.37-1-amd64: segfault in multiple apps when using this kernel
Package: linux-2.6
Version: 2.6.37-1
Severity: important
Running this kernel I can log into gnome fine, but running dselect gives:
A error occurred during the signature verification. The repository is not
updated and the previous index files will be used. GPG error:
http://ftp.nl.debian.org unstable InRelease: Internal error: Good signature,
but could not determine key fingerprint?!
and the following line is reported in syslog
gpgv[5221]: segfault at ffffffff89480143 ip 0000000000404000 sp
00007fff3dd925f8 error 6 in gpgv[400000+55000]
Attempting to decompress good archive files results in crc errors less than
halfway through the set. Extracting the same archive in 2.6.32 works just fine.
(4.4GB zipped or rar'ed ISO files)
Also the adobe flash player crashes immediately, I can only send a bug report
to adobe by clicking in the window, adobe restarts after sending the report (no
idea what is in it, I get to see nothing) and crashes again immediately.. As in
the above 2 problems it works fine in 2.6.32.
Eventually the machine grinds to a halt, X freezes, the hard disk reports that
it is trying to access beyond the "end" of the device or something and all I
can do is hit the reset buttone and go back the kernel 2.6.32.
I'll stop here before it crashes again...
Thanks
Matthew
-- Package-specific info:
** Version:
Linux version 2.6.37-1-amd64 (Debian 2.6.37-1) (ben@decadent.org.uk) (gcc version 4.4.5 (Debian 4.4.5-10) ) #1 SMP Tue Feb 15 17:43:38 UTC 2011
** Command line:
BOOT_IMAGE=/boot/vmlinuz-2.6.37-1-amd64 root=UUID=17ae8e4c-882c-4f4a-9b89-7815b7c9185d ro quiet
** Tainted: P (1)
* Proprietary module has been loaded.
** Kernel log:
[ 2.792029] sd 8:0:0:0: [sdc] Assuming drive cache: write through
[ 2.792414] sd 7:0:0:1: Attached scsi generic sg5 type 0
[ 2.793340] sd 7:0:0:2: Attached scsi generic sg6 type 0
[ 2.794293] sd 7:0:0:3: Attached scsi generic sg7 type 0
[ 2.794498] sd 8:0:0:0: [sdc] Test WP failed, assume Write Enabled
[ 2.794501] sd 8:0:0:0: [sdc] Assuming drive cache: write through
[ 2.794601] sd 7:0:0:0: [sdd] Attached SCSI removable disk
[ 2.796251] sd 7:0:0:1: [sde] Attached SCSI removable disk
[ 2.797871] sd 7:0:0:2: [sdf] Attached SCSI removable disk
[ 2.798486] sd 7:0:0:3: [sdg] Attached SCSI removable disk
[ 3.287786] sdc: sdc1
[ 3.289732] sd 8:0:0:0: [sdc] Test WP failed, assume Write Enabled
[ 3.289736] sd 8:0:0:0: [sdc] Assuming drive cache: write through
[ 3.289789] sd 8:0:0:0: [sdc] Attached SCSI disk
[ 3.403264] PM: Starting manual resume from disk
[ 3.403269] PM: Hibernation image partition 8:5 present
[ 3.403271] PM: Looking for hibernation image.
[ 3.409888] PM: Image not found (code -22)
[ 3.409890] PM: Hibernation image not present or could not be loaded.
[ 3.460394] EXT3-fs: barriers not enabled
[ 3.478008] kjournald starting. Commit interval 5 seconds
[ 3.478143] EXT3-fs (sda1): mounted filesystem with ordered data mode
[ 4.829995] udev[332]: starting version 166
[ 5.252383] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2
[ 5.252396] ACPI: Power Button [PWRB]
[ 5.252468] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input3
[ 5.252474] ACPI: Sleep Button [SLPB]
[ 5.252540] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[ 5.252544] ACPI: Power Button [PWRF]
[ 5.328288] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 5.331659] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 5.350760] ACPI: acpi_idle registered with cpuidle
[ 5.350809] ACPI: processor limited to max C-state 1
[ 5.434459] cfg80211: Calling CRDA to update world regulatory domain
[ 5.605278] gameport gameport0: EMU10K1 is pci0000:00:09.1/gameport0, io 0xa800, speed 1155kHz
[ 5.689457] input: PC Speaker as /devices/platform/pcspkr/input/input5
[ 5.750286] MCE: In-kernel MCE decoding enabled.
[ 5.868739] EDAC MC: Ver: 2.1.0 Feb 15 2011
[ 5.891381] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[ 5.891387] Disabling lock debugging due to kernel taint
[ 6.103678] [fglrx] Maximum main memory to use for locked dma buffers: 2876 MBytes.
[ 6.103811] [fglrx] vendor: 1002 device: 9596 count: 1
[ 6.104161] [fglrx] ioport: bar 1, base 0x9000, size: 0x100
[ 6.104176] pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 6.104208] pci 0000:01:00.0: PCI: Disallowing DAC for device
[ 6.104398] [fglrx] Kernel PAT support is enabled
[ 6.104429] [fglrx] module loaded - fglrx 8.82.8 [Jan 26 2011] with 1 minors
[ 6.467777] EDAC amd64_edac: Ver: 3.3.0 Feb 15 2011
[ 6.467850] EDAC amd64: ECC is enabled by BIOS.
[ 6.467879] EDAC MC: Rev E or earlier detected
[ 6.467948] EDAC MC0: Giving out device to 'amd64_edac' 'RevF': DEV 0000:00:18.2
[ 6.467974] EDAC PCI0: Giving out device to module 'amd64_edac' controller 'EDAC PCI controller': DEV '0000:00:18.2' (POLLED)
[ 6.535373] b43-phy0: Broadcom 4306 WLAN found (core revision 5)
[ 6.719471] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 6.720265] Registered led device: b43-phy0::tx
[ 6.720294] Registered led device: b43-phy0::rx
[ 6.720318] Registered led device: b43-phy0::radio
[ 6.720336] Broadcom 43xx driver loaded [ Features: PMLS, Firmware-ID: FW13 ]
[ 6.970126] EMU10K1_Audigy 0000:00:09.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 6.972871] Installing spdif_bug patch: SB Audigy 2 ZS [SB0360]
[ 7.279442] HDA Intel 0000:01:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 7.279490] HDA Intel 0000:01:00.1: PCI: Disallowing DAC for device
[ 8.333265] Adding 6041596k swap on /dev/sda5. Priority:-1 extents:1 across:6041596k
[ 207.953471] EXT3-fs (sda1): using internal journal
[ 208.259022] loop: module loaded
[ 208.967498] IPv6 over IPv4 tunneling driver
[ 208.968434] sit0: Disabled Privacy Extensions
[ 208.969280] xs6all: Disabled Privacy Extensions
[ 209.320955] skge 0000:00:0a.0: eth0: enabling interface
[ 209.325651] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 209.802701] fuse init (API version 7.15)
[ 211.007806] skge 0000:00:0a.0: eth0: Link is up at 100 Mbps, full duplex, flow control none
[ 211.008562] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 213.555086] [fglrx] AGP detected, AgpState = 0x1f000a1a (hardware caps of chipset)
[ 213.555093] [fglrx] [agp] enabling AGP with mode=0x1f000b1a
[ 213.555099] agpgart-amd64 0000:00:00.0: AGP 3.5 bridge
[ 213.555114] agpgart-amd64 0000:00:00.0: putting AGP V3 device into 8x mode
[ 213.555198] fglrx_pci 0000:01:00.0: putting AGP V3 device into 8x mode
[ 213.555208] [fglrx] AGP enabled, AgpCommand = 0x1f000312 (selected caps)
[ 213.579197] [fglrx] Setup AGP aperture
[ 213.721922] [fglrx] Could not enable MSI; System prevented initialization
[ 213.723817] [fglrx] Firegl kernel thread PID: 3064
[ 213.724666] [fglrx] Firegl kernel thread PID: 3067
[ 213.724713] [fglrx] Firegl kernel thread PID: 3069
[ 213.724942] [fglrx] IRQ 16 Enabled
[ 214.391257] powernow-k8: Found 1 AMD Athlon(tm) 64 FX-51 Processor (1 cpu cores) (version 2.20.00)
[ 214.392189] [Firmware Bug]: powernow-k8: No PSB or ACPI _PSS objects
[ 214.392192] powernow-k8: Make sure that your BIOS is up to date and Cool'N'Quiet support is enabled in BIOS setup
[ 215.680632] [fglrx] Gart cacheable size:1317 M.
[ 215.680640] [fglrx] Reserved FB block: Shared offset:0, size:1000000
[ 215.680644] [fglrx] Reserved FB block: Unshared offset:fd0b000, size:2f5000
[ 215.680647] [fglrx] Reserved FB block: Unshared offset:1fffc000, size:4000
[ 221.312020] eth0: no IPv6 routers present
[ 237.796057] EXT3-fs: barriers not enabled
[ 237.811451] kjournald starting. Commit interval 5 seconds
[ 237.811720] EXT3-fs (sdc1): warning: maximal mount count reached, running e2fsck is recommended
[ 237.812414] EXT3-fs (sdc1): using internal journal
[ 237.812418] EXT3-fs (sdc1): mounted filesystem with ordered data mode
[ 698.550122] gpgv[5221]: segfault at ffffffff89480143 ip 0000000000404000 sp 00007fff3dd925f8 error 6 in gpgv[400000+55000]
[ 698.888400] gpgv[5222]: segfault at ffffffff89480143 ip 0000000000404000 sp 00007fffc47b7238 error 6 in gpgv[400000+55000]
** Model information
sys_vendor: To Be Filled By O.E.M.
product_name: To Be Filled By O.E.M.
product_version: To Be Filled By O.E.M.
chassis_vendor: Chassis Manufacture
chassis_version: Chassis Version
bios_vendor: American Megatrends Inc.
bios_version: 1003.008
board_vendor: ASUSTeK Computer Inc.
board_name: SK8V
board_version: Rev 1.xx
** Loaded modules:
Module Size Used by
mperf 1243 0
cpufreq_userspace 2016 0
cpufreq_powersave 942 0
cpufreq_stats 2633 0
cpufreq_conservative 7646 0
fuse 54683 1
sit 9642 0
tunnel4 1997 1 sit
loop 13819 0
firewire_sbp2 11503 0
snd_hda_codec_hdmi 19401 1
snd_hda_intel 19418 0
snd_hda_codec 62429 2 snd_hda_codec_hdmi,snd_hda_intel
snd_emu10k1_synth 4928 0
snd_emux_synth 25503 1 snd_emu10k1_synth
snd_seq_virmidi 3729 1 snd_emux_synth
snd_seq_midi_emul 4307 1 snd_emux_synth
snd_pcm_oss 32140 0
snd_emu10k1 123967 2 snd_emu10k1_synth
snd_mixer_oss 12767 1 snd_pcm_oss
snd_ac97_codec 99205 1 snd_emu10k1
ac97_bus 1126 1 snd_ac97_codec
snd_util_mem 2190 2 snd_emux_synth,snd_emu10k1
snd_hwdep 5484 3 snd_hda_codec,snd_emux_synth,snd_emu10k1
snd_pcm 61869 5 snd_hda_intel,snd_hda_codec,snd_pcm_oss,snd_emu10k1,snd_ac97_codec
snd_seq_midi 4486 0
arc4 1330 2
snd_rawmidi 15945 3 snd_seq_virmidi,snd_emu10k1,snd_seq_midi
ecb 1881 2
snd_seq_midi_event 4786 2 snd_seq_virmidi,snd_seq_midi
snd_seq 42454 5 snd_emux_synth,snd_seq_virmidi,snd_seq_midi_emul,snd_seq_midi,snd_seq_midi_event
b43 149371 0
i2c_viapro 5139 0
amd64_edac_mod 13937 0
snd_timer 16304 3 snd_emu10k1,snd_pcm,snd_seq
snd_seq_device 4531 5 snd_emu10k1_synth,snd_emu10k1,snd_seq_midi,snd_rawmidi,snd_seq
snd 47148 17 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec,snd_emux_synth,snd_seq_virmidi,snd_pcm_oss,snd_emu10k1,snd_mixer_oss,snd_ac97_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
i2c_core 16442 1 i2c_viapro
rng_core 3118 1 b43
tpm_tis 7141 0
fglrx 2649431 105
snd_page_alloc 6289 3 snd_hda_intel,snd_emu10k1,snd_pcm
k8temp 3195 0
tpm 9907 1 tpm_tis
edac_core 30192 3 amd64_edac_mod
soundcore 4614 1 snd
tpm_bios 4709 1 tpm
mac80211 168033 1 b43
edac_mce_amd 8023 1 amd64_edac_mod
pcspkr 1739 0
emu10k1_gp 1836 0
gameport 7248 2 emu10k1_gp
cfg80211 114213 2 b43,mac80211
evdev 8115 9
processor 23794 0
shpchp 21923 0
pci_hotplug 19711 1 shpchp
thermal_sys 11764 1 processor
button 4722 0
rfkill 13870 1 cfg80211
ext3 106405 2
jbd 36976 1 ext3
mbcache 5104 1 ext3
sg 19079 0
sd_mod 28354 5
sr_mod 12759 0
cdrom 29865 1 sr_mod
crc_t10dif 1300 1 sd_mod
usbhid 30826 0
ata_generic 3151 0
hid 65110 1 usbhid
usb_storage 39623 1
uas 6917 0
uhci_hcd 18394 0
sata_promise 9729 0
pata_via 7653 0
ehci_hcd 31374 0
ssb 37506 1 b43
sata_via 7792 2
libata 143222 4 ata_generic,sata_promise,pata_via,sata_via
mmc_core 54665 2 b43,ssb
scsi_mod 154559 7 firewire_sbp2,sg,sr_mod,sd_mod,usb_storage,uas,libata
usbcore 118823 6 usbhid,usb_storage,uas,uhci_hcd,ehci_hcd
firewire_ohci 22154 0
pcmcia 29435 2 b43,ssb
pcmcia_core 10413 1 pcmcia
floppy 50981 0
firewire_core 42273 2 firewire_sbp2,firewire_ohci
crc_itu_t 1331 1 firewire_core
skge 33547 0
nls_base 6369 1 usbcore
** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
allow-hotplug eth0
iface eth0 inet dhcp
auto xs6all
iface xs6all inet6 v4tunnel
endpoint 194.109.5.241
up ip route add default via 2001:888:10:9f::1
address 2001:888:10:9f::2
netmask 64
ttl 64
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
link/ether 00:0e:a6:20:4a:5e brd ff:ff:ff:ff:ff:ff
inet 192.168.1.64/24 brd 192.168.1.255 scope global eth0
inet6 fe80::20e:a6ff:fe20:4a5e/64 scope link
valid_lft forever preferred_lft forever
3: wlan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
link/ether 00:0f:66:74:a5:87 brd ff:ff:ff:ff:ff:ff
4: sit0: <NOARP> mtu 1480 qdisc noop state DOWN
link/sit 0.0.0.0 brd 0.0.0.0
5: xs6all: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1480 qdisc noqueue state UNKNOWN
link/sit 0.0.0.0 peer 194.109.5.241
inet6 2001:888:10:9f::2/64 scope global
valid_lft forever preferred_lft forever
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed
lo: 560 8 0 0 0 0 0 0 560 8 0 0 0 0 0 0
eth0: 1214897 1118 0 0 0 0 0 33 168815 1080 0 0 0 0 0 0
wlan0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
sit0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
xs6all: 1103813 862 0 0 0 0 0 0 68424 739 0 0 0 0 0 0
*** Protocol statistics:
Ip:
1102 total packets received
2 with invalid addresses
0 forwarded
0 incoming packets discarded
1100 incoming packets delivered
1034 requests sent out
8 dropped because of missing route
Icmp:
0 ICMP messages received
0 input ICMP message failed.
ICMP input histogram:
0 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
Tcp:
37 active connections openings
0 passive connection openings
1 failed connection attempts
7 connection resets received
0 connections established
1017 segments received
940 segments send out
9 segments retransmited
0 bad segments received.
168 resets sent
Udp:
75 packets received
0 packets to unknown port received.
0 packet receive errors
75 packets sent
UdpLite:
TcpExt:
22 TCP sockets finished time wait in fast timer
15 delayed acks sent
613 packet headers predicted
47 acknowledgments not containing data payload received
1 predicted acknowledgments
2 other TCP timeouts
2 connections reset due to unexpected data
7 connections reset due to early user close
1 connections aborted due to timeout
IpExt:
InMcastPkts: 15
OutMcastPkts: 17
InOctets: 1196314
OutOctets: 143978
InMcastOctets: 2715
OutMcastOctets: 2819
*** Device features:
eth0: 0x4803
lo: 0x13865
sit0: 0x3000
wlan0: 0x2000
xs6all: 0x3000
** PCI devices:
00:00.0 Host bridge [0600]: VIA Technologies, Inc. VT8385 [K8T800 AGP] Host Bridge [1106:3188] (rev 01)
Subsystem: ASUSTeK Computer Inc. K8V Deluxe/K8V-X motherboard [1043:80a3]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+ INTx-
Latency: 64
Region 0: Memory at <ignored> (32-bit, prefetchable)
Capabilities: <access denied>
Kernel driver in use: agpgart-amd64
00:01.0 PCI bridge [0604]: VIA Technologies, Inc. VT8237 PCI bridge [K8T800/K8T890 South] [1106:b188] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00009000-00009fff
Memory behind bridge: fc900000-fcefffff
Prefetchable memory behind bridge: d4800000-f47fffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:07.0 FireWire (IEEE 1394) [0c00]: VIA Technologies, Inc. VT6306/7/8 [Fire II(M)] IEEE 1394 OHCI Controller [1106:3044] (rev 80) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. A8V/A8N/P4P800 series motherboard [1043:808a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (8000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fd800000 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at cc00 [size=128]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
00:08.0 RAID bus controller [0104]: Promise Technology, Inc. PDC20378 (FastTrak 378/SATA 378) [105a:3373] (rev 02)
Subsystem: ASUSTeK Computer Inc. K8V Deluxe/PC-DL Deluxe motherboard [1043:80f5]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (1000ns min, 4500ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at a000 [size=64]
Region 1: I/O ports at ec00 [size=16]
Region 2: I/O ports at dc00 [size=128]
Region 3: Memory at fda00000 (32-bit, non-prefetchable) [size=4K]
Region 4: Memory at fd900000 (32-bit, non-prefetchable) [size=128K]
Capabilities: <access denied>
Kernel driver in use: sata_promise
00:09.0 Multimedia audio controller [0401]: Creative Labs SB Audigy [1102:0004] (rev 04)
Subsystem: Creative Labs Device [1102:2001]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at a400 [size=64]
Capabilities: <access denied>
Kernel driver in use: EMU10K1_Audigy
00:09.1 Input device controller [0980]: Creative Labs SB Audigy Game Port [1102:7003] (rev 04)
Subsystem: Creative Labs SB Audigy Game Port [1102:0040]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Region 0: I/O ports at a800 [size=8]
Capabilities: <access denied>
Kernel driver in use: Emu10k1_gameport
00:09.2 FireWire (IEEE 1394) [0c00]: Creative Labs SB Audigy FireWire Port [1102:4001] (rev 04) (prog-if 10 [OHCI])
Subsystem: Creative Labs SB Audigy FireWire Port [1102:0010]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (500ns min, 1000ns max), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at fdc00000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at fdb00000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
00:0a.0 Ethernet controller [0200]: 3Com Corporation 3c940 10/100/1000Base-T [Marvell] [10b7:1700] (rev 12)
Subsystem: ASUSTeK Computer Inc. A7V600/P4P800/K8V motherboard [1043:80eb]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (5750ns min, 7750ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at fdd00000 (32-bit, non-prefetchable) [size=16K]
Region 1: I/O ports at b000 [size=256]
Capabilities: <access denied>
Kernel driver in use: skge
00:0d.0 Network controller [0280]: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller [14e4:4320] (rev 03)
Subsystem: Linksys Device [1737:0013]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fde00000 (32-bit, non-prefetchable) [size=8K]
Kernel driver in use: b43-pci-bridge
00:0f.0 RAID bus controller [0104]: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller [1106:3149] (rev 80)
Subsystem: ASUSTeK Computer Inc. A7V600/K8V Deluxe/K8V-X/A8V Deluxe motherboard [1043:80ed]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin B routed to IRQ 20
Region 0: I/O ports at e400 [size=8]
Region 1: I/O ports at e000 [size=4]
Region 2: I/O ports at d800 [size=8]
Region 3: I/O ports at d400 [size=4]
Region 4: I/O ports at d000 [size=16]
Region 5: I/O ports at c800 [size=256]
Capabilities: <access denied>
Kernel driver in use: sata_via
00:0f.1 IDE interface [0101]: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE [1106:0571] (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. A7V600/K8V-X/A8V Deluxe motherboard [1043:80ed]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 20
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
Region 4: I/O ports at fc00 [size=16]
Capabilities: <access denied>
Kernel driver in use: pata_via
00:10.0 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 81) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. A7V600/K8V-X/A8V Deluxe motherboard [1043:80ed]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 4: I/O ports at b400 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:10.1 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 81) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. A7V600/K8V-X/A8V Deluxe motherboard [1043:80ed]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 4: I/O ports at b800 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:10.2 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 81) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. A7V600/K8V-X/A8V Deluxe motherboard [1043:80ed]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at c000 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:10.3 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 81) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. A7V600/K8V-X/A8V Deluxe motherboard [1043:80ed]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at c400 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:10.4 USB Controller [0c03]: VIA Technologies, Inc. USB 2.0 [1106:3104] (rev 86) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. A7V600/K8V-X/A8V Deluxe motherboard [1043:80ed]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 21
Region 0: Memory at fdf00000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:11.0 ISA bridge [0601]: VIA Technologies, Inc. VT8237 ISA bridge [KT600/K8T800/K8T890 South] [1106:3227]
Subsystem: ASUSTeK Computer Inc. A7V600/K8V-X/A8V Deluxe motherboard [1043:80ed]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:11.5 Multimedia audio controller [0401]: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller [1106:3059] (rev 60)
Subsystem: ASUSTeK Computer Inc. Device [1043:80f3]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 0
Region 0: I/O ports at 1000 [disabled] [size=256]
Capabilities: <access denied>
00:11.6 Communication controller [0780]: VIA Technologies, Inc. AC'97 Modem Controller [1106:3068] (rev 80)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 0
Region 0: I/O ports at 1400 [disabled] [size=256]
Capabilities: <access denied>
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map [1022:1101]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller [1022:1102]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Kernel driver in use: amd64_edac
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control [1022:1103]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Kernel driver in use: k8temp
01:00.0 VGA compatible controller [0300]: ATI Technologies Inc RV635 PRO AGP [Radeon HD 3650] [1002:9596] (prog-if 00 [VGA controller])
Subsystem: Hightech Information System Ltd. Device [1787:0028]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (2000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
Region 1: I/O ports at 9000 [size=256]
Region 2: Memory at fce00000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at fcd00000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: fglrx_pci
01:00.1 Audio device [0403]: ATI Technologies Inc RV635 Audio device [Radeon HD 3600 Series] [1002:aa20]
Subsystem: Hightech Information System Ltd. Device [1787:aa20]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (2000ns min), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at fcc00000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 002: ID 1307:0330 Transcend Information, Inc.
Bus 001 Device 004: ID 1058:1021 Western Digital Technologies, Inc. Elements 2TB
Bus 002 Device 002: ID 046d:c03d Logitech, Inc. M-BT96a Pilot Optical Mouse
-- System Information:
Debian Release: wheezy/sid
APT prefers unstable
APT policy: (500, 'unstable'), (1, 'experimental')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.37-1-amd64 (SMP w/1 CPU core)
Locale: LANG=en_US.utf8, LC_CTYPE=en_US.utf8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-2.6.37-1-amd64 depends on:
ii debconf [debconf-2.0] 1.5.38 Debian configuration management sy
ii initramfs-tools [linux-initra 0.98.8 tools for generating an initramfs
ii linux-base 2.6.37-1 Linux image base package
ii module-init-tools 3.12-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.37-1-amd64 recommends:
ii firmware-linux-free 2.6.37-1 Binary firmware for various driver
Versions of packages linux-image-2.6.37-1-amd64 suggests:
pn grub | lilo <none> (no description available)
pn linux-doc-2.6.37 <none> (no description available)
Versions of packages linux-image-2.6.37-1-amd64 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-linux <none> (no description available)
ii firmware-linux-nonfree 0.28 Binary firmware for various driver
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn xen-hypervisor <none> (no description available)
-- debconf information:
linux-image-2.6.37-1-amd64/postinst/depmod-error-initrd-2.6.37-1-amd64: false
linux-image-2.6.37-1-amd64/postinst/ignoring-do-bootloader-2.6.37-1-amd64:
* linux-image-2.6.37-1-amd64/postinst/missing-firmware-2.6.37-1-amd64:
linux-image-2.6.37-1-amd64/prerm/removing-running-kernel-2.6.37-1-amd64: true
Reply to: