Bug#615173: linux-image-2.6.32-5-686: rt73usb wlan doesn't work
Package: linux-2.6
Version: 2.6.32-30
Severity: normal
Tags: upstream
hope it's the right location for the bug report
if i plug in my "PLANEX GW-US54Mini2" (lsusb says that) wlan adapter, the
rt73usb driver loads, the wlan0 interface appears - but NetworkManager says
"device not ready".
modprobe doesn't complain (exit status 0 when loading or removing)
===========================================
root@jtkpc-debian:~# ifconfig wlan0 up
SIOCSIFFLAGS: No such file or directory
[exit status: 255]
root@jtkpc-debian:~# iwconfig wlan0
wlan0 IEEE 802.11bg ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:on
root@jtkpc-debian:~# dmesg |tail -20
[ 4964.325878] Registered led device: rt73usb-phy0::quality
[ 4964.326600] usbcore: registered new interface driver rt73usb
[ 5039.999665] usbcore: deregistering interface driver rt73usb
[ 5058.464149] cfg80211: Using static regulatory domain info
[ 5058.464166] cfg80211: Regulatory domain: US
[ 5058.464181] (start_freq - end_freq @ bandwidth), (max_antenna_gain,
max_eirp)
[ 5058.464198] (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
[ 5058.464214] (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 5058.464225] (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 5058.464240] (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 5058.464256] (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 5058.464266] (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
[ 5058.466040] cfg80211: Calling CRDA for country: US
[ 5058.926970] phy0: Selected rate control algorithm 'minstrel'
[ 5058.944191] Registered led device: rt73usb-phy0::radio
[ 5058.953029] Registered led device: rt73usb-phy0::assoc
[ 5058.955721] Registered led device: rt73usb-phy0::quality
[ 5058.957327] usbcore: registered new interface driver rt73usb
[ 5105.924355] rt73usb 1-7:1.0: firmware: requesting rt73.bin
[ 5105.970179] phy0 -> rt2x00lib_request_firmware: Error - Failed to request
Firmware.
===================================
the device works correctly on fedora with kernel 2.6.35.11-83.fc14.i686 and
Ubuntu with 2.6.32-28-generic.
-- Package-specific info:
** Version:
Linux version 2.6.32-5-686 (Debian 2.6.32-30) (ben@decadent.org.uk) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Wed Jan 12 04:01:41 UTC 2011
** Command line:
BOOT_IMAGE=/boot/vmlinuz-2.6.32-5-686 root=UUID=1dfd6396-aa94-498f-8959-e8af6e25cb4a ro quiet
** Tainted: P (1)
* Proprietary module has been loaded.
** Kernel log:
[ 3229.422046] ata_piix 0000:00:1f.2: PCI INT B disabled
[ 3229.422116] ata2: port disabled. ignoring.
[ 3229.422164] ata_piix 0000:00:1f.1: PCI INT A disabled
[ 3229.524062] HDA Intel 0000:00:1b.0: PCI INT A disabled
[ 3229.524106] ACPI handle has no context!
[ 3229.540516] ACPI: Preparing to enter system sleep state S4
[ 3229.540890] PM: Saving platform NVS memory
[ 3229.543948] Disabling non-boot CPUs ...
[ 3229.544002] Extended CMOS year: 2000
[ 3229.544002] PM: Creating hibernation image:
[ 3229.544002] PM: Need to copy 100729 pages
[ 3229.544002] PM: Normal pages needed: 12349 + 1024, available pages: 213805
[ 3229.544002] PM: Restoring platform NVS memory
[ 3229.544002] CPU0: Thermal monitoring enabled (TM2)
[ 3229.544002] Extended CMOS year: 2000
[ 3229.544002] Force enabled HPET at resume
[ 3229.544157] ACPI: Waking up from system sleep state S4
[ 3229.544956] HDA Intel 0000:00:1b.0: restoring config space at offset 0x1 (was 0x100106, writing 0x100102)
[ 3229.545374] ata_piix 0000:00:1f.1: restoring config space at offset 0x1 (was 0x2880001, writing 0x2880005)
[ 3229.545403] ata_piix 0000:00:1f.2: restoring config space at offset 0x1 (was 0x2b00001, writing 0x2b00005)
[ 3229.545466] nvidia 0000:01:00.0: restoring config space at offset 0x3 (was 0x8, writing 0x0)
[ 3229.545521] tg3 0000:05:00.0: restoring config space at offset 0xc (was 0x0, writing 0x3f7f0000)
[ 3229.580059] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 3229.580067] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 3229.676144] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 3229.676180] usb usb2: root hub lost power or was reset
[ 3229.676201] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 3229.676235] usb usb3: root hub lost power or was reset
[ 3229.676258] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 3229.676292] usb usb4: root hub lost power or was reset
[ 3229.676312] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 3229.676345] usb usb5: root hub lost power or was reset
[ 3229.676364] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 3229.676369] usb usb1: root hub lost power or was reset
[ 3229.680241] ehci_hcd 0000:00:1d.7: cache line size of 128 is not supported
[ 3229.680262] pci 0000:00:1e.0: setting latency timer to 64
[ 3229.680276] ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 3229.680281] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 3229.682408] ACPI Exception: AE_AML_PACKAGE_LIMIT, Index (0FFFFFFFF) is beyond end of object (20090903/exoparg2-445)
[ 3229.682420] ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.IDE_.STM_] (Node f6c133d8), AE_AML_PACKAGE_LIMIT
[ 3229.682440] ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.IDE_.SECN._STM] (Node f6c13570), AE_AML_PACKAGE_LIMIT
[ 3229.682461] ata2: ACPI set timing mode failed (status=0x300b)
[ 3229.682485] ata2: port disabled. ignoring.
[ 3229.682510] ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 3229.682515] ata_piix 0000:00:1f.2: setting latency timer to 64
[ 3230.041681] ata1.01: ACPI cmd ef/03:42:00:00:00:b0 (SET FEATURES) filtered out
[ 3230.041687] ata1.01: ACPI cmd ef/03:0c:00:00:00:b0 (SET FEATURES) filtered out
[ 3230.042786] parport_pc 00:0b: activated
[ 3230.043368] serial 00:0c: activated
[ 3230.048596] ata1.00: ACPI cmd ef/03:42:00:00:00:a0 (SET FEATURES) filtered out
[ 3230.048601] ata1.00: ACPI cmd ef/03:0c:00:00:00:a0 (SET FEATURES) filtered out
[ 3230.048770] ata3.01: ACPI cmd 91/00:3f:00:00:00:b0 (INITIALIZE DEVICE PARAMETERS) succeeded
[ 3230.048775] ata3.01: ACPI cmd ef/03:45:00:00:00:b0 (SET FEATURES) filtered out
[ 3230.048896] ata3.01: ACPI cmd c6/00:10:00:00:00:b0 (SET MULTIPLE MODE) succeeded
[ 3230.064433] ata1.00: configured for UDMA/33
[ 3230.064633] ata3.00: ACPI cmd 91/00:3f:00:00:00:a0 (INITIALIZE DEVICE PARAMETERS) succeeded
[ 3230.064638] ata3.00: ACPI cmd ef/03:45:00:00:00:a0 (SET FEATURES) filtered out
[ 3230.064642] ata3.00: ACPI cmd ef/03:0c:00:00:00:a0 (SET FEATURES) filtered out
[ 3230.064752] ata3.00: ACPI cmd c6/00:10:00:00:00:a0 (SET MULTIPLE MODE) succeeded
[ 3230.080262] ata1.01: configured for UDMA/33
[ 3230.088381] ata3.00: configured for UDMA/133
[ 3230.104362] ata3.01: configured for UDMA/133
[ 3230.128363] ata3.00: configured for UDMA/133
[ 3230.144362] ata3.01: configured for UDMA/133
[ 3230.144367] ata3: EH complete
[ 3230.644022] sd 2:0:0:0: [sda] Starting disk
[ 3230.647919] sd 2:0:1:0: [sdb] Starting disk
[ 3230.764043] usb 1-7: reset high speed USB device using ehci_hcd and address 2
[ 3231.244039] usb 5-2: reset low speed USB device using uhci_hcd and address 2
[ 3231.551439] PM: Image restored successfully.
[ 3231.551444] Restarting tasks ... done.
[ 3231.556564] PM: Basic memory bitmaps freed
[ 3236.498989] tg3 0000:05:00.0: PME# disabled
[ 3236.560088] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 3237.306601] eth1: setting half-duplex.
[ 3237.306882] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 3238.179618] tg3: eth0: Link is up at 100 Mbps, full duplex.
[ 3238.179623] tg3: eth0: Flow control is off for TX and off for RX.
[ 3238.179775] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 3248.764018] eth0: no IPv6 routers present
[ 3291.435975] tg3: eth0: Link is down.
[ 3294.610024] tg3: eth0: Link is up at 100 Mbps, full duplex.
[ 3294.610047] tg3: eth0: Flow control is off for TX and off for RX.
[ 3299.442984] tg3: eth0: Link is down.
[ 3301.061181] tg3: eth0: Link is up at 100 Mbps, full duplex.
[ 3301.061203] tg3: eth0: Flow control is off for TX and off for RX.
[ 3324.469166] tg3: eth0: Link is down.
[ 3326.104679] tg3: eth0: Link is up at 100 Mbps, full duplex.
[ 3326.104697] tg3: eth0: Flow control is on for TX and on for RX.
[ 3543.713643] tg3: eth0: Link is down.
[ 3545.329790] tg3: eth0: Link is up at 100 Mbps, full duplex.
[ 3545.329808] tg3: eth0: Flow control is off for TX and off for RX.
[ 3567.252405] tg3: eth0: Link is down.
[ 3568.821303] tg3: eth0: Link is up at 100 Mbps, full duplex.
[ 3568.821326] tg3: eth0: Flow control is on for TX and on for RX.
[ 4318.845874] vboxdrv: Trying to deactivate the NMI watchdog permanently...
[ 4318.845893] vboxdrv: Successfully done.
[ 4318.845908] vboxdrv: Found 1 processor cores.
[ 4318.850123] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[ 4318.850139] vboxdrv: Successfully loaded version 3.2.10_OSE (interface 0x00140001).
** Model information
not available
** Loaded modules:
Module Size Used by
vboxnetadp 5118 0
vboxnetflt 12633 0
vboxdrv 126614 2 vboxnetadp,vboxnetflt
crc_itu_t 1035 0
rt2x00usb 5713 0
rt2x00lib 19101 1 rt2x00usb
led_class 1757 1 rt2x00lib
mac80211 123574 2 rt2x00usb,rt2x00lib
cfg80211 87661 2 rt2x00lib,mac80211
acpi_cpufreq 4951 0
speedstep_lib 2468 0
cpufreq_userspace 1480 0
cpufreq_conservative 4018 0
cpufreq_stats 1940 0
cpufreq_powersave 602 0
ppdev 4058 0
lp 5570 0
sco 5857 2
bridge 33019 0
stp 996 1 bridge
bnep 7444 2
l2cap 21705 3 bnep
crc16 1027 1 l2cap
bluetooth 36319 5 sco,bnep,l2cap
nfsd 193919 11
lockd 49437 1 nfsd
nfs_acl 1695 1 nfsd
auth_rpcgss 25268 1 nfsd
sunrpc 134776 10 nfsd,lockd,nfs_acl,auth_rpcgss
exportfs 2618 1 nfsd
binfmt_misc 4907 1
fuse 44033 1
loop 9765 0
arc4 974 0
ecb 1405 0
snd_hda_codec_realtek 163294 1
snd_hda_intel 16811 1
snd_hda_codec 46002 2 snd_hda_codec_realtek,snd_hda_intel
snd_hwdep 4054 1 snd_hda_codec
snd_pcm 47226 2 snd_hda_intel,snd_hda_codec
snd_seq 35463 0
snd_timer 12258 2 snd_pcm,snd_seq
snd_seq_device 3673 1 snd_seq
rfkill 10264 4 cfg80211,bluetooth
snd 34375 10 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_seq,snd_timer,snd_seq_device
nvidia 9223737 28
soundcore 3450 1 snd
snd_page_alloc 5045 2 snd_hda_intel,snd_pcm
rng_core 2178 0
i2c_i801 6462 0
parport_pc 15799 1
container 1833 0
evdev 5609 7
i2c_core 12696 2 nvidia,i2c_i801
parport 22554 3 ppdev,lp,parport_pc
button 3598 0
processor 26327 1 acpi_cpufreq
pcspkr 1207 0
usbhid 28008 0
hid 50893 1 usbhid
ext3 94212 2
jbd 32169 1 ext3
mbcache 3762 1 ext3
sg 15968 0
sr_mod 10770 0
sd_mod 25977 5
crc_t10dif 1012 1 sd_mod
cdrom 26487 1 sr_mod
ata_generic 2067 0
ata_piix 17736 3
tg3 88273 0
floppy 40923 0
3c59x 25036 0
mii 2714 1 3c59x
thermal 9206 0
uhci_hcd 16057 0
libata 115753 2 ata_generic,ata_piix
scsi_mod 101429 4 sg,sr_mod,sd_mod,libata
ehci_hcd 27851 0
libphy 11638 1 tg3
usbcore 98453 5 rt2x00usb,usbhid,uhci_hcd,ehci_hcd
nls_base 4541 1 usbcore
thermal_sys 9378 2 processor,thermal
** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
allow-hotplug eth0
#NetworkManager#iface eth0 inet dhcp
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN qlen 1000
link/ether 00:01:02:9d:8a:b8 brd ff:ff:ff:ff:ff:ff
3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000
link/ether 00:30:05:c3:90:69 brd ff:ff:ff:ff:ff:ff
inet 10.42.43.10/24 brd 10.42.43.255 scope global eth0
inet6 fe80::230:5ff:fec3:9069/64 scope link
valid_lft forever preferred_lft forever
5: pan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN
link/ether 46:bf:71:37:75:41 brd ff:ff:ff:ff:ff:ff
6: vboxnet0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
link/ether 0a:00:27:00:00:00 brd ff:ff:ff:ff:ff:ff
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed
lo: 97897 787 0 0 0 0 0 0 97897 787 0 0 0 0 0 0
eth1: 0 0 0 0 0 0 0 0 120 2 0 0 0 0 2 0
eth0:36778544 26070 0 0 0 0 0 9 1060943 14359 0 0 0 0 0 0
pan0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
vboxnet0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
*** Protocol statistics:
Ip:
40654 total packets received
9 with invalid addresses
0 forwarded
0 incoming packets discarded
40645 incoming packets delivered
24105 requests sent out
16 outgoing packets dropped
73 dropped because of missing route
Icmp:
164 ICMP messages received
1 input ICMP message failed.
ICMP input histogram:
destination unreachable: 164
120 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
destination unreachable: 120
IcmpMsg:
InType3: 164
OutType3: 120
Tcp:
197 active connections openings
0 passive connection openings
2 failed connection attempts
12 connection resets received
4 connections established
39089 segments received
22471 segments send out
206 segments retransmited
0 bad segments received.
5 resets sent
Udp:
1365 packets received
120 packets to unknown port received.
0 packet receive errors
1353 packets sent
UdpLite:
TcpExt:
17 TCP sockets finished time wait in fast timer
113 delayed acks sent
Quick ack mode was activated 21 times
36422 packet headers predicted
274 acknowledgments not containing data payload received
75 predicted acknowledgments
6 congestion windows recovered without slow start after partial ack
32 other TCP timeouts
22 DSACKs sent for old packets
5 DSACKs received
3 connections reset due to unexpected data
21 connections aborted due to timeout
TCPDSACKIgnoredNoUndo: 1
IpExt:
InMcastPkts: 148
OutMcastPkts: 117
InBcastPkts: 107
OutBcastPkts: 102
InOctets: 54519961
OutOctets: 1554599
InMcastOctets: 25329
OutMcastOctets: 19510
InBcastOctets: 16656
OutBcastOctets: 15016
*** Device features:
eth0: 0x109a3
eth1: 0x803
lo: 0x13865
pan0: 0xff3865
vboxnet0: 0x0
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub [8086:2770] (rev 02)
Subsystem: Fujitsu Technology Solutions Device [1734:1084]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:01.0 PCI bridge [0604]: Intel Corporation 82945G/GZ/P/PL PCI Express Root Port [8086:2771] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: f1000000-f3ffffff
Prefetchable memory behind bridge: 00000000e0000000-00000000efffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1b.0 Audio device [0403]: Intel Corporation N10/ICH 7 Family High Definition Audio Controller [8086:27d8] (rev 01)
Subsystem: Fujitsu Technology Solutions Device [1734:1083]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at f0000000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
00:1c.0 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 1 [8086:27d0] (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00001000-00001fff
Memory behind bridge: 80000000-801fffff
Prefetchable memory behind bridge: 0000000080200000-00000000803fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.1 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 2 [8086:27d2] (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 00006000-00006fff
Memory behind bridge: f4000000-f40fffff
Prefetchable memory behind bridge: 0000000080400000-00000000805fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.2 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 3 [8086:27d4] (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=07, subordinate=07, sec-latency=0
I/O behind bridge: 00007000-00007fff
Memory behind bridge: 80600000-807fffff
Prefetchable memory behind bridge: 0000000080800000-00000000809fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.3 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 4 [8086:27d6] (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=09, subordinate=09, sec-latency=0
I/O behind bridge: 00008000-00008fff
Memory behind bridge: 80a00000-80bfffff
Prefetchable memory behind bridge: 0000000080c00000-0000000080dfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 [8086:27c8] (rev 01) (prog-if 00 [UHCI])
Subsystem: Fujitsu Technology Solutions Device [1734:1085]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at 2000 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 [8086:27c9] (rev 01) (prog-if 00 [UHCI])
Subsystem: Fujitsu Technology Solutions Device [1734:1085]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 22
Region 4: I/O ports at 2400 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 [8086:27ca] (rev 01) (prog-if 00 [UHCI])
Subsystem: Fujitsu Technology Solutions Device [1734:1085]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 21
Region 4: I/O ports at 2800 [size=32]
Kernel driver in use: uhci_hcd
00:1d.3 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 [8086:27cb] (rev 01) (prog-if 00 [UHCI])
Subsystem: Fujitsu Technology Solutions Device [1734:1085]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 20
Region 4: I/O ports at 2c00 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller [8086:27cc] (rev 01) (prog-if 20 [EHCI])
Subsystem: Fujitsu Technology Solutions Device [1734:1085]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f0004000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev e1) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=0b, subordinate=0b, sec-latency=80
I/O behind bridge: 00005000-00005fff
Memory behind bridge: f4100000-f41fffff
Prefetchable memory behind bridge: 0000000080e00000-0000000080efffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge [8086:27b8] (rev 01)
Subsystem: Fujitsu Technology Solutions Device [1734:1085]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.1 IDE interface [0101]: Intel Corporation 82801G (ICH7 Family) IDE Controller [8086:27df] (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: Fujitsu Technology Solutions Device [1734:1085]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 3400 [size=16]
Kernel driver in use: ata_piix
00:1f.2 IDE interface [0101]: Intel Corporation N10/ICH7 Family SATA IDE Controller [8086:27c0] (rev 01) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Fujitsu Technology Solutions Device [1734:1085]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at 3430 [size=8]
Region 1: I/O ports at 3424 [size=4]
Region 2: I/O ports at 3428 [size=8]
Region 3: I/O ports at 3420 [size=4]
Region 4: I/O ports at 3410 [size=16]
Capabilities: <access denied>
Kernel driver in use: ata_piix
00:1f.3 SMBus [0c05]: Intel Corporation N10/ICH 7 Family SMBus Controller [8086:27da] (rev 01)
Subsystem: Fujitsu Technology Solutions Device [1734:1085]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 3000 [size=32]
Kernel driver in use: i801_smbus
01:00.0 VGA compatible controller [0300]: nVidia Corporation G84 [GeForce 8600 GT] [10de:0402] (rev a1) (prog-if 00 [VGA controller])
Subsystem: PC Partner Limited Device [174b:8030]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f1000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at f2000000 (64-bit, non-prefetchable) [size=32M]
Region 5: I/O ports at 4000 [size=128]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: nvidia
05:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5751 Gigabit Ethernet PCI Express [14e4:1677] (rev 01)
Subsystem: Fujitsu Technology Solutions Device [1734:1096]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at f4000000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at <ignored> [disabled]
Capabilities: <access denied>
Kernel driver in use: tg3
0b:05.0 Ethernet controller [0200]: 3Com Corporation 3c905C-TX/TX-M [Tornado] [10b7:9200] (rev 74)
Subsystem: 3Com Corporation 3C905CX-TX/TX-M Fast Etherlink for PC Management NIC [10b7:1000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 80 (2500ns min, 2500ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at 5000 [size=128]
Region 1: Memory at f4100000 (32-bit, non-prefetchable) [size=128]
[virtual] Expansion ROM at 80e00000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: 3c59x
** USB devices:
Bus 005 Device 002: ID 046d:c019 Logitech, Inc. Optical Tilt Wheel Mouse
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 002: ID 2019:ab50 PLANEX GW-US54Mini2
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: 6.0
APT prefers squeeze-updates
APT policy: (500, 'squeeze-updates'), (500, 'stable')
Architecture: i386 (i686)
Kernel: Linux 2.6.32-5-686 (SMP w/1 CPU core)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-2.6.32-5-686 depends on:
ii debconf [debconf-2.0] 1.5.36.1 Debian configuration management sy
ii initramfs-tools [linux-initra 0.98.8 tools for generating an initramfs
ii linux-base 2.6.32-30 Linux image base package
ii module-init-tools 3.12-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.32-5-686 recommends:
pn firmware-linux-free <none> (no description available)
ii libc6-i686 2.11.2-10 Embedded GNU C Library: Shared lib
Versions of packages linux-image-2.6.32-5-686 suggests:
pn grub | lilo <none> (no description available)
pn linux-doc-2.6.32 <none> (no description available)
Versions of packages linux-image-2.6.32-5-686 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-linux <none> (no description available)
pn firmware-linux-nonfree <none> (no description available)
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn xen-hypervisor <none> (no description available)
-- debconf information:
linux-image-2.6.32-5-686/prerm/removing-running-kernel-2.6.32-5-686: true
linux-image-2.6.32-5-686/postinst/depmod-error-initrd-2.6.32-5-686: false
linux-image-2.6.32-5-686/postinst/ignoring-do-bootloader-2.6.32-5-686:
linux-image-2.6.32-5-686/postinst/missing-firmware-2.6.32-5-686:
Reply to: