Bug#596390: Log messages from 2.6.30 and 2.6.32
On 9/10/2010 4:57 PM, Ben Hutchings wrote:
Please test a newer version. There was a bug fix to r8169 in version
2.6.32-16 which might address this.
I was already on the -20 version. Then I tried the -21 recently added
to the backports archive, with no change.
After a little experimentation, I found a not-very-good workaround. The
first thing I tried was plugging it into a dumb 100Mb/s switch. The
link came right up, so I did a little further experimentation. If I
turn off autoneg with ethtool, it comes up at 10/half. Basically it
will work at anything except for gigabit, and I cannot set speed 1000 if
autoneg is turned off. For now, I have hard-set both sides to
100/Full. At this time I do not have another gigabit switch I can try,
but I will see what I can do about that. I would like to emphasize that
this works without issue on 2.6.30, though.
Should it interest you, here's a show ver from my switch:
rivendell#show ver
Cisco IOS Software, C3550 Software (C3550-IPSERVICESK9-M), Version
12.2(44)SE6,
RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 09-Mar-09 20:28 by gereddy
Image text-base: 0x00003000, data-base: 0x012A99FC
ROM: Bootstrap program is C3550 boot loader
rivendell uptime is 34 weeks, 5 days, 15 hours, 27 minutes
System returned to ROM by power-on
System restarted at 08:53:10 MST Sun Jan 10 2010
System image file is
"flash:c3550-ipservicesk9-mz.122-44.SE6/c3550-ipservicesk9-
mz.122-44.SE6.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be
found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
Cisco WS-C3550-12T (PowerPC) processor (revision M0) with 65526K/8192K
bytes of
memory.
Processor board ID CHK0706V183
Last reset from warm-reset
Running Layer2/3 Switching Image
Ethernet-controller 1 has 1 Gigabit Ethernet/IEEE 802.3 interface
Ethernet-controller 2 has 1 Gigabit Ethernet/IEEE 802.3 interface
Ethernet-controller 3 has 1 Gigabit Ethernet/IEEE 802.3 interface
Ethernet-controller 4 has 1 Gigabit Ethernet/IEEE 802.3 interface
Ethernet-controller 5 has 1 Gigabit Ethernet/IEEE 802.3 interface
Ethernet-controller 6 has 1 Gigabit Ethernet/IEEE 802.3 interface
Ethernet-controller 7 has 1 Gigabit Ethernet/IEEE 802.3 interface
Ethernet-controller 8 has 1 Gigabit Ethernet/IEEE 802.3 interface
Ethernet-controller 9 has 1 Gigabit Ethernet/IEEE 802.3 interface
Ethernet-controller 10 has 1 Gigabit Ethernet/IEEE 802.3 interface
Ethernet-controller 11 has 1 Gigabit Ethernet/IEEE 802.3 interface
Ethernet-controller 12 has 1 Gigabit Ethernet/IEEE 802.3 interface
12 Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.
384K bytes of flash-simulated NVRAM.
Base ethernet MAC Address: 00:0C:30:10:FC:00
Motherboard assembly number: 73-5527-16
Power supply part number: 34-0967-01
Motherboard serial number: CAT07050H7G
Power supply serial number: DCA07040FZU
Model revision number: M0
Motherboard revision number: A0
Model number: WS-C3550-12T
System serial number: CHK0706V183
Configuration register is 0x10F
rivendell#
Reply to: