Bug#572084: linux-image-2.6.32-2-orion5x: NFS kernel daemon support disabled?
Package: linux-2.6
Version: 2.6.32-8
Severity: normal
After upgrading its kernel from 2.6.30-2-orion5x to 2.6.32-2-orion5x, I
cannot mount NFS v4 filesystems exported by my QNAP-409. When attempting
to restart nfs-kernel-server, I get the warning "Not starting NFS kernel
daemon: no support in current kernel. (warning)."
Looking at /boot/config-2.6.3{0,2}-2-orion5x, I notice that there are no
differences in the NFS defines, so the issue may be elsewhere:
$ diff config-2.6.30-2-orion5x config-2.6.32-2-orion5x | grep NFS
> # CONFIG_NFS_V4_1 is not set
Best regards,
Marco
-- Package-specific info:
** Version:
Linux version 2.6.32-2-orion5x (Debian 2.6.32-8) (ben@decadent.org.uk) (gcc version 4.3.4 (Debian 4.3.4-6) ) #1 Fri Feb 12 18:12:26 UTC 2010
** Command line:
console=ttyS0,115200n8 root=/dev/ram rw initrd=0x800000,0x3fffff
** Not tainted
** Kernel log:
[ 15.807260] disk 1, o:1, dev:sdb4
[ 15.810657] disk 2, o:1, dev:sdc4
[ 15.814053] disk 3, o:1, dev:sdd4
[ 15.817761] md3: detected capacity change from 0 to 2968503189504
[ 15.827266] md3: unknown partition table
[ 16.200899] device-mapper: uevent: version 1.0.3
[ 16.213670] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 16.734575] kjournald starting. Commit interval 5 seconds
[ 16.776991] EXT3 FS on md1, internal journal
[ 16.781283] EXT3-fs: mounted filesystem with ordered data mode.
[ 19.760494] udevd version 125 started
[ 28.303276] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 28.440151] MV-643xx 10/100/1000 ethernet driver version 1.4
[ 28.452110] mv643xx_eth smi: probed
[ 28.517926] net eth0: port 0 with MAC address 00:08:9b:ad:18:00
[ 28.780462] usbcore: registered new interface driver usbfs
[ 28.824341] usbcore: registered new interface driver hub
[ 28.856461] usbcore: registered new device driver usb
[ 28.977325] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 28.983933] orion-ehci orion-ehci.0: Marvell Orion EHCI
[ 29.013854] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[ 29.066231] orion-ehci orion-ehci.0: irq 17, io mem 0xf1050000
[ 29.086167] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 29.092196] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 29.099128] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 29.106365] usb usb1: Product: Marvell Orion EHCI
[ 29.111066] usb usb1: Manufacturer: Linux 2.6.32-2-orion5x ehci_hcd
[ 29.117347] usb usb1: SerialNumber: orion-ehci.0
[ 29.197741] usb usb1: configuration #1 chosen from 1 choice
[ 29.225771] hub 1-0:1.0: USB hub found
[ 29.229664] hub 1-0:1.0: 1 port detected
[ 29.546139] usb 1-1: new high speed USB device using orion-ehci and address 2
[ 29.717864] usb 1-1: New USB device found, idVendor=05e3, idProduct=0607
[ 29.724560] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 29.731729] usb 1-1: Product: USB2.0 Hub
[ 29.796155] usb 1-1: configuration #1 chosen from 1 choice
[ 29.828269] hub 1-1:1.0: USB hub found
[ 29.856115] hub 1-1:1.0: 4 ports detected
[ 30.146656] usb 1-1.2: new low speed USB device using orion-ehci and address 3
[ 30.370289] usb 1-1.2: New USB device found, idVendor=051d, idProduct=0002
[ 30.377206] usb 1-1.2: New USB device strings: Mfr=3, Product=1, SerialNumber=2
[ 30.384498] usb 1-1.2: Product: Back-UPS CS 500 FW:808.q8.I USB FW:q8
[ 30.391003] usb 1-1.2: Manufacturer: American Power Conversion
[ 30.396852] usb 1-1.2: SerialNumber: 4B0827P61177
[ 30.504601] usb 1-1.2: configuration #1 chosen from 1 choice
[ 31.872575] usbcore: registered new interface driver hiddev
[ 33.480348] generic-usb 0003:051D:0002.0001: hiddev0,hidraw0: USB HID v1.10 Device [American Power Conversion Back-UPS CS 500 FW:808.q8.I USB FW:q8] on usb-orion-ehci.0-1.2/input0
[ 33.500871] usbcore: registered new interface driver usbhid
[ 33.512864] usbhid: v2.6:USB HID core driver
[ 35.064935] Adding 489848k swap on /dev/md2. Priority:-1 extents:1 across:489848k
[ 35.836959] EXT3 FS on md1, internal journal
[ 37.925238] loop: module loaded
[ 58.943332] kjournald starting. Commit interval 5 seconds
[ 59.023983] EXT3 FS on dm-0, internal journal
[ 59.028409] EXT3-fs: mounted filesystem with ordered data mode.
[ 59.096987] kjournald starting. Commit interval 5 seconds
[ 59.146857] EXT3 FS on dm-2, internal journal
[ 59.151240] EXT3-fs: mounted filesystem with ordered data mode.
[ 59.284494] kjournald starting. Commit interval 5 seconds
[ 59.302755] EXT3 FS on dm-10, internal journal
[ 59.307264] EXT3-fs: mounted filesystem with ordered data mode.
[ 59.416207] kjournald starting. Commit interval 5 seconds
[ 59.432092] EXT3 FS on dm-9, internal journal
[ 59.436517] EXT3-fs: mounted filesystem with ordered data mode.
[ 59.529291] kjournald starting. Commit interval 5 seconds
[ 59.551157] EXT3 FS on dm-3, internal journal
[ 59.555538] EXT3-fs: mounted filesystem with ordered data mode.
[ 59.593235] kjournald starting. Commit interval 5 seconds
[ 59.615443] EXT3 FS on dm-1, internal journal
[ 59.621898] EXT3-fs: mounted filesystem with ordered data mode.
[ 59.732287] kjournald starting. Commit interval 5 seconds
[ 59.760595] EXT3 FS on dm-5, internal journal
[ 59.764973] EXT3-fs: mounted filesystem with ordered data mode.
[ 59.801780] kjournald starting. Commit interval 5 seconds
[ 59.836504] EXT3 FS on dm-6, internal journal
[ 59.840884] EXT3-fs: mounted filesystem with ordered data mode.
[ 59.905428] kjournald starting. Commit interval 5 seconds
[ 59.934754] EXT3 FS on dm-11, internal journal
[ 59.939262] EXT3-fs: mounted filesystem with ordered data mode.
[ 59.995530] kjournald starting. Commit interval 5 seconds
[ 60.023450] EXT3 FS on dm-7, internal journal
[ 60.027875] EXT3-fs: mounted filesystem with ordered data mode.
[ 60.089092] kjournald starting. Commit interval 5 seconds
[ 60.103425] EXT3 FS on dm-8, internal journal
[ 60.107855] EXT3-fs: mounted filesystem with ordered data mode.
[ 63.502364] NET: Registered protocol family 10
[ 63.512879] lo: Disabled Privacy Extensions
[ 63.519810] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 65.171452] eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[ 65.178382] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 65.495258] RPC: Registered udp transport module.
[ 65.500030] RPC: Registered tcp transport module.
[ 65.504722] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 65.968509] Slow work thread pool: Starting up
[ 65.977549] Slow work thread pool: Ready
[ 65.988044] FS-Cache: Loaded
[ 66.211518] FS-Cache: Netfs 'nfs' registered for caching
[ 66.600435] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 75.226080] eth0: no IPv6 routers present
[ 87.837806] warning: `ntpd' uses 32-bit capabilities (legacy support in use)
** Model information
Processor : Feroceon rev 0 (v5l)
Hardware : QNAP TS-409
Revision : 0000
** Loaded modules:
Module Size Used by
nfsd 247648 2
exportfs 3000 1 nfsd
nfs 269374 0
lockd 63141 2 nfsd,nfs
fscache 34101 1 nfs
nfs_acl 2277 2 nfsd,nfs
auth_rpcgss 33314 2 nfsd,nfs
sunrpc 171030 6 nfsd,nfs,lockd,nfs_acl,auth_rpcgss
ipv6 253185 25
ext2 55407 2
loop 11411 0
usbhid 34123 1
hid 62858 1 usbhid
evdev 6582 0
ehci_hcd 32780 0
usbcore 110912 4 usbhid,ehci_hcd
mv643xx_eth 22546 0
nls_base 5367 1 usbcore
libphy 14128 1 mv643xx_eth
gpio_keys 2655 0
ext3 111008 12
jbd 37430 1 ext3
mbcache 4860 2 ext2,ext3
dm_mirror 11377 0
dm_region_hash 6573 1 dm_mirror
dm_log 8058 2 dm_mirror,dm_region_hash
dm_snapshot 20989 0
dm_mod 56571 39 dm_mirror,dm_log,dm_snapshot
raid456 50883 1
async_raid6_recov 4120 1 raid456
async_pq 3420 2 raid456,async_raid6_recov
raid6_pq 75781 2 async_raid6_recov,async_pq
async_xor 2563 3 raid456,async_raid6_recov,async_pq
xor 4819 1 async_xor
async_memcpy 956 2 raid456,async_raid6_recov
async_tx 2008 5 raid456,async_raid6_recov,async_pq,async_xor,async_memcpy
raid1 19477 3
md_mod 80234 6 raid456,raid1
sd_mod 30988 20
crc_t10dif 1106 1 sd_mod
sata_mv 24205 16
libata 133831 1 sata_mv
scsi_mod 119100 2 sd_mod,libata
** PCI devices:
not available
** Sound cards:
-- System Information:
Debian Release: 5.0.4
APT prefers stable
APT policy: (700, 'stable')
Architecture: armel (armv5tel)
Kernel: Linux 2.6.32-2-orion5x
Locale: LANG=en_GB.UTF-8, LC_CTYPE=en_GB.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.32-2-orion5x depends on:
ii debconf [debconf-2.0] 1.5.24 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92o tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.32-2-orion5x recommends:
pn firmware-linux-free <none> (no description available)
ii uboot-mkimage 0.4 generate kernel image for U-Boot
Versions of packages linux-image-2.6.32-2-orion5x suggests:
pn fdutils <none> (no description available)
pn linux-doc-2.6.32 <none> (no description available)
Versions of packages linux-image-2.6.32-2-orion5x is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-linux <none> (no description available)
pn firmware-linux-nonfree <none> (no description available)
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
-- debconf information:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.32-2-orion5x/postinst/depmod-error-initrd-2.6.32-2-orion5x: false
linux-image-2.6.32-2-orion5x/postinst/missing-firmware-2.6.32-2-orion5x:
linux-image-2.6.32-2-orion5x/prerm/would-invalidate-boot-loader-2.6.32-2-orion5x: true
linux-image-2.6.32-2-orion5x/postinst/bootloader-test-error-2.6.32-2-orion5x:
linux-image-2.6.32-2-orion5x/postinst/bootloader-error-2.6.32-2-orion5x:
linux-image-2.6.32-2-orion5x/prerm/removing-running-kernel-2.6.32-2-orion5x: true
Reply to: