Your message dated Sun, 05 Dec 2010 17:48:38 +0000 with message-id <1291571318.8025.86.camel@localhost> and subject line Re: Bug#606029: linux-image-2.6.32-5-686: cfg80211 or zd1211 incorrectly detects regdom or misses configuration dialog has caused the Debian Bug report #606029, regarding linux-image-2.6.32-5-686: cfg80211 or zd1211 incorrectly detects regdom or misses configuration dialog to be marked as done. This means that you claim that the problem has been dealt with. If this is not the case it is now your responsibility to reopen the Bug report if necessary, and/or fix the problem forthwith. (NB: If you are a system administrator and have no idea what this message is talking about, this may indicate a serious mail system misconfiguration somewhere. Please contact owner@bugs.debian.org immediately.) -- 606029: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=606029 Debian Bug Tracking System Contact owner@bugs.debian.org with problems
--- Begin Message ---
- To: Debian Bug Tracking System <submit@bugs.debian.org>
- Subject: linux-image-2.6.32-5-686: cfg80211 or zd1211 incorrectly detects regdom or misses configuration dialog
- From: Olivier Berger <oberger@ouvaton.org>
- Date: Sun, 05 Dec 2010 18:30:15 +0100
- Message-id: <[🔎] 20101205173015.3375.1267.reportbug@josephine>
Package: linux-2.6 Version: 2.6.32-28 Severity: normal Hi. Trying to connect to a wifi network (in France) which uses Channel 13 fails with a USB network card which requires zd1211. It appears that after stock install, I have : # cat /sys/module/cfg80211/parameters/ieee80211_regdom 00 I need to set /etc/modprobe.d/cfg80211.conf with : options cfg80211 ieee80211_regdom=EU to make it work. I guess there's a bug here, which may be related to the lack of debconf question for setting such parameters or similar configuration mechanism prompting the user, or to a buggy automagic detection of the regdom. In any case, it's far from obvious for non-expert user why some AP would be seen (channels OK for US) and some not (for instance on channels 12 and 13). Hope this helps. Best regards, -- Package-specific info: ** Version: Linux version 2.6.32-5-686 (Debian 2.6.32-28) (ben@decadent.org.uk) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Thu Nov 25 18:43:34 UTC 2010 ** Command line: BOOT_IMAGE=/vmlinuz-2.6.32-5-686 root=/dev/mapper/josephine-root ro quiet ** Not tainted ** Kernel log: [ 5.116781] input: PS/2 Mouse as /devices/platform/i8042/serio1/input/input7 [ 5.135257] input: AlpsPS/2 ALPS GlidePoint as /devices/platform/i8042/serio1/input/input8 [ 5.193154] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 5.339644] intel_rng: FWH not detected [ 5.383340] [drm] Initialized drm 1.1.0 20060810 [ 5.424102] cfg80211: Using static regulatory domain info [ 5.424105] cfg80211: Regulatory domain: US [ 5.424107] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 5.424111] (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm) [ 5.424114] (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 5.424118] (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 5.424121] (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 5.424125] (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 5.424128] (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm) [ 5.424402] cfg80211: Calling CRDA for country: US [ 5.748489] i915 0000:00:02.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11 [ 5.748496] i915 0000:00:02.0: setting latency timer to 64 [ 5.767564] [drm] set up 0M of stolen space [ 5.885198] [drm] initialized overlay support [ 6.218734] yenta_cardbus 0000:01:01.0: CardBus bridge found [1028:0163] [ 6.218749] yenta_cardbus 0000:01:01.0: Using CSCINT to route CSC interrupts to PCI [ 6.218752] yenta_cardbus 0000:01:01.0: Routing CardBus interrupts to PCI [ 6.218758] yenta_cardbus 0000:01:01.0: TI: mfunc 0x012c1222, devctl 0x64 [ 6.649130] usb 1-3: reset high speed USB device using ehci_hcd and address 2 [ 6.802911] yenta_cardbus 0000:01:01.0: ISA IRQ mask 0x0458, PCI irq 11 [ 6.802916] yenta_cardbus 0000:01:01.0: Socket status: 30000086 [ 6.802922] pci_bus 0000:01: Raising subordinate bus# of parent bus (#01) from #01 to #05 [ 6.802932] yenta_cardbus 0000:01:01.0: pcmcia: parent PCI bridge I/O window: 0xe000 - 0xefff [ 6.802937] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xe000-0xefff: clean. [ 6.803510] yenta_cardbus 0000:01:01.0: pcmcia: parent PCI bridge Memory window: 0xfc000000 - 0xfdffffff [ 6.803514] yenta_cardbus 0000:01:01.0: pcmcia: parent PCI bridge Memory window: 0x40000000 - 0x43ffffff [ 6.909641] Console: switching to colour frame buffer device 175x65 [ 6.920550] fb0: inteldrmfb frame buffer device [ 6.920552] registered panic notifier [ 6.920581] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0 [ 7.224453] phy0: Selected rate control algorithm 'minstrel' [ 7.225205] zd1211rw 1-3:1.0: phy0 [ 7.225229] usbcore: registered new interface driver zd1211rw [ 7.389083] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: clean. [ 7.389899] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: clean. [ 7.390252] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: clean. [ 7.390303] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: clean. [ 7.390742] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean. [ 7.728139] Intel ICH 0000:00:1f.5: PCI INT B -> Link[LNKB] -> GSI 5 (level, low) -> IRQ 5 [ 7.728176] Intel ICH 0000:00:1f.5: setting latency timer to 64 [ 8.556038] intel8x0_measure_ac97_clock: measured 55243 usecs (2662 samples) [ 8.556042] intel8x0: clocking to 48000 [ 8.557234] Intel ICH Modem 0000:00:1f.6: PCI INT B -> Link[LNKB] -> GSI 5 (level, low) -> IRQ 5 [ 8.557256] Intel ICH Modem 0000:00:1f.6: setting latency timer to 64 [ 8.660071] MC'97 1 converters and GPIO not ready (0xff00) [ 9.758441] EXT3 FS on dm-0, internal journal [ 9.936827] loop: module loaded [ 10.580930] Adding 2170872k swap on /dev/mapper/josephine-swap_1. Priority:-1 extents:1 across:2170872k [ 11.262981] kjournald starting. Commit interval 5 seconds [ 11.263316] EXT3 FS on dm-2, internal journal [ 11.263322] EXT3-fs: mounted filesystem with ordered data mode. [ 12.472799] fuse init (API version 7.13) [ 15.174506] usb 1-3: firmware: requesting zd1211/zd1211_ub [ 15.318326] usb 1-3: firmware: requesting zd1211/zd1211_uphr [ 15.586222] zd1211rw 1-3:1.0: firmware version 4605 [ 15.626230] zd1211rw 1-3:1.0: zd1211 chip 0586:3401 v4330 high 00-13-49 AL2230_RF pa0 g---- [ 15.628746] cfg80211: Calling CRDA for country: DE [ 15.650969] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 15.669901] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 17.725435] Bluetooth: Core ver 2.15 [ 17.725498] NET: Registered protocol family 31 [ 17.725500] Bluetooth: HCI device and connection manager initialized [ 17.725504] Bluetooth: HCI socket layer initialized [ 17.778037] Bluetooth: L2CAP ver 2.14 [ 17.778040] Bluetooth: L2CAP socket layer initialized [ 17.894094] Bluetooth: RFCOMM TTY layer initialized [ 17.894100] Bluetooth: RFCOMM socket layer initialized [ 17.894103] Bluetooth: RFCOMM ver 1.11 [ 17.946275] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 17.946279] Bluetooth: BNEP filters: protocol multicast [ 18.124701] Bridge firewalling registered [ 18.318460] Bluetooth: SCO (Voice Link) ver 0.6 [ 18.318463] Bluetooth: SCO socket layer initialized [ 19.440908] lp0: using parport0 (interrupt-driven). [ 19.705514] ppdev: user-space parallel port driver [ 62.517918] wlan0: direct probe to AP f2:6e:07:bc:ac:b2 (try 1) [ 62.716071] wlan0: direct probe to AP f2:6e:07:bc:ac:b2 (try 2) [ 62.916040] wlan0: direct probe to AP f2:6e:07:bc:ac:b2 (try 3) [ 63.118030] wlan0: direct probe to AP f2:6e:07:bc:ac:b2 timed out [ 68.439823] wlan0: direct probe to AP 3e:f6:4b:3f:7e:5a (try 1) [ 68.636059] wlan0: direct probe to AP 3e:f6:4b:3f:7e:5a (try 2) [ 68.836098] wlan0: direct probe to AP 3e:f6:4b:3f:7e:5a (try 3) [ 69.036561] wlan0: direct probe to AP 3e:f6:4b:3f:7e:5a timed out [ 74.383936] wlan0: direct probe to AP 3e:f6:4b:3f:7e:5a (try 1) [ 74.580122] wlan0: direct probe to AP 3e:f6:4b:3f:7e:5a (try 2) [ 74.780052] wlan0: direct probe to AP 3e:f6:4b:3f:7e:5a (try 3) [ 74.980077] wlan0: direct probe to AP 3e:f6:4b:3f:7e:5a timed out [ 80.296965] wlan0: direct probe to AP b2:5d:9e:21:9b:d6 (try 1) [ 80.496057] wlan0: direct probe to AP b2:5d:9e:21:9b:d6 (try 2) [ 80.696056] wlan0: direct probe to AP b2:5d:9e:21:9b:d6 (try 3) [ 80.896053] wlan0: direct probe to AP b2:5d:9e:21:9b:d6 timed out [ 86.226972] wlan0: direct probe to AP f2:6e:07:bc:ac:b2 (try 1) [ 86.424051] wlan0: direct probe to AP f2:6e:07:bc:ac:b2 (try 2) [ 86.624036] wlan0: direct probe to AP f2:6e:07:bc:ac:b2 (try 3) [ 86.824060] wlan0: direct probe to AP f2:6e:07:bc:ac:b2 timed out ** Model information not available ** Loaded modules: Module Size Used by acpi_cpufreq 4943 0 cpufreq_powersave 602 0 cpufreq_userspace 1480 0 cpufreq_conservative 4018 0 cpufreq_stats 1940 0 ppdev 4058 0 lp 5570 0 sco 5857 2 bridge 33019 0 stp 996 1 bridge bnep 7444 2 rfcomm 25171 0 l2cap 21705 6 bnep,rfcomm crc16 1027 1 l2cap bluetooth 36319 6 sco,bnep,rfcomm,l2cap binfmt_misc 4907 1 fuse 43829 1 ext2 46293 1 firewire_sbp2 9647 0 loop 9765 0 snd_intel8x0m 8100 0 snd_intel8x0 19555 1 snd_ac97_codec 79148 2 snd_intel8x0m,snd_intel8x0 ac97_bus 710 1 snd_ac97_codec snd_pcm_oss 28671 0 snd_mixer_oss 10461 1 snd_pcm_oss snd_pcm 47226 4 snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_pcm_oss arc4 974 2 ecb 1405 2 snd_seq_midi 3576 0 snd_rawmidi 12513 1 snd_seq_midi pcmcia 16194 0 snd_seq_midi_event 3684 1 snd_seq_midi snd_seq 35463 2 snd_seq_midi,snd_seq_midi_event snd_timer 12258 2 snd_pcm,snd_seq yenta_socket 16403 1 rsrc_nonstatic 7057 1 yenta_socket zd1211rw 32550 0 snd_seq_device 3673 3 snd_seq_midi,snd_rawmidi,snd_seq mac80211 123574 1 zd1211rw i915 222064 2 pcmcia_core 20450 3 pcmcia,yenta_socket,rsrc_nonstatic drm_kms_helper 18301 1 i915 snd 34375 12 snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device cfg80211 87661 2 zd1211rw,mac80211 drm 112088 3 i915,drm_kms_helper i2c_algo_bit 3497 1 i915 shpchp 21220 0 soundcore 3450 1 snd snd_page_alloc 5045 3 snd_intel8x0m,snd_intel8x0,snd_pcm joydev 6739 0 parport_pc 15799 1 dell_laptop 1533 0 rfkill 10264 5 bluetooth,cfg80211,dell_laptop rng_core 2178 0 parport 22554 3 ppdev,lp,parport_pc i2c_core 12696 4 i915,drm_kms_helper,drm,i2c_algo_bit psmouse 44657 0 pcspkr 1207 0 pci_hotplug 18065 1 shpchp dcdbas 3892 1 dell_laptop processor 26327 2 acpi_cpufreq button 3598 1 i915 video 14605 1 i915 battery 3782 0 output 1204 1 video ac 1640 0 evdev 5609 14 serio_raw 2916 0 ext3 94204 2 jbd 32169 1 ext3 mbcache 3762 2 ext2,ext3 dm_mod 46094 9 sd_mod 25969 3 crc_t10dif 1012 1 sd_mod ata_generic 2047 0 uhci_hcd 16057 0 ata_piix 17736 2 thermal 9206 0 firewire_ohci 16509 0 libata 115745 2 ata_generic,ata_piix ehci_hcd 27851 0 thermal_sys 9378 3 processor,video,thermal e100 22317 0 mii 2714 1 e100 firewire_core 31187 2 firewire_sbp2,firewire_ohci crc_itu_t 1035 1 firewire_core scsi_mod 101421 3 firewire_sbp2,sd_mod,libata usbcore 98453 4 zd1211rw,uhci_hcd,ehci_hcd nls_base 4541 1 usbcore ** PCI devices: 00:00.0 Host bridge [0600]: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller [8086:3580] (rev 02) Subsystem: Dell Latitude D505 [1028:0163] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Region 0: Memory at <unassigned> (32-bit, prefetchable) Capabilities: <access denied> Kernel driver in use: agpgart-intel 00:00.1 System peripheral [0880]: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller [8086:3584] (rev 02) Subsystem: Dell Latitude D505 [1028:0163] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:00.3 System peripheral [0880]: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller [8086:3585] (rev 02) Subsystem: Dell Latitude D505 [1028:0163] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:02.0 VGA compatible controller [0300]: Intel Corporation 82852/855GM Integrated Graphics Device [8086:3582] (rev 02) (prog-if 00 [VGA controller]) Subsystem: Dell Latitude D505 [1028:0163] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+ Latency: 0 Interrupt: pin A routed to IRQ 11 Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M] Region 1: Memory at faf80000 (32-bit, non-prefetchable) [size=512K] Region 2: I/O ports at c000 [size=8] Expansion ROM at <unassigned> [disabled] Capabilities: <access denied> Kernel driver in use: i915 00:02.1 Display controller [0380]: Intel Corporation 82852/855GM Integrated Graphics Device [8086:3582] (rev 02) Subsystem: Dell Latitude D505 [1028:0163] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M] Region 1: Memory at faf00000 (32-bit, non-prefetchable) [size=512K] Capabilities: <access denied> 00:1d.0 USB Controller [0c03]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 [8086:24c2] (rev 01) (prog-if 00 [UHCI]) Subsystem: Dell Latitude D505 [1028:0163] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 11 Region 4: I/O ports at bf80 [size=32] Kernel driver in use: uhci_hcd 00:1d.1 USB Controller [0c03]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 [8086:24c4] (rev 01) (prog-if 00 [UHCI]) Subsystem: Dell Latitude D505 [1028:0163] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 11 Region 4: I/O ports at bf40 [size=32] Kernel driver in use: uhci_hcd 00:1d.2 USB Controller [0c03]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 [8086:24c7] (rev 01) (prog-if 00 [UHCI]) Subsystem: Dell Latitude D505 [1028:0163] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 11 Region 4: I/O ports at bf20 [size=32] Kernel driver in use: uhci_hcd 00:1d.7 USB Controller [0c03]: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller [8086:24cd] (rev 01) (prog-if 20 [EHCI]) Subsystem: Dell Latitude D505 [1028:0163] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 11 Region 0: Memory at faeffc00 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev 81) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR+ INTx- Latency: 0 Bus: primary=00, secondary=01, subordinate=05, sec-latency=32 I/O behind bridge: 0000e000-0000efff Memory behind bridge: fc000000-fdffffff Prefetchable memory behind bridge: 40000000-43ffffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- 00:1f.0 ISA bridge [0601]: Intel Corporation 82801DBM (ICH4-M) LPC Interface Bridge [8086:24cc] (rev 01) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:1f.1 IDE interface [0101]: Intel Corporation 82801DBM (ICH4-M) IDE Controller [8086:24ca] (rev 01) (prog-if 8a [Master SecP PriP]) Subsystem: Dell Latitude D505 [1028:0163] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at 01f0 [size=8] Region 1: I/O ports at 03f4 [size=1] Region 2: I/O ports at 0170 [size=8] Region 3: I/O ports at 0374 [size=1] Region 4: I/O ports at bfa0 [size=16] Region 5: Memory at 44000000 (32-bit, non-prefetchable) [size=1K] Kernel driver in use: ata_piix 00:1f.5 Multimedia audio controller [0401]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller [8086:24c5] (rev 01) Subsystem: Dell Latitude D505 [1028:0163] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 5 Region 0: I/O ports at d800 [size=256] Region 1: I/O ports at dc40 [size=64] Region 2: Memory at faeff800 (32-bit, non-prefetchable) [size=512] Region 3: Memory at faeff400 (32-bit, non-prefetchable) [size=256] Capabilities: <access denied> Kernel driver in use: Intel ICH 00:1f.6 Modem [0703]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem Controller [8086:24c6] (rev 01) (prog-if 00 [Generic]) Subsystem: Conexant Systems, Inc. D480 MDC V.9x Modem [14f1:5422] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 5 Region 0: I/O ports at d400 [size=256] Region 1: I/O ports at d080 [size=128] Capabilities: <access denied> Kernel driver in use: Intel ICH Modem 01:01.0 CardBus bridge [0607]: Texas Instruments PCI4510 PC card Cardbus Controller [104c:ac44] (rev 02) Subsystem: Dell Latitude D505 [1028:0163] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 168, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 11 Region 0: Memory at fc000000 (32-bit, non-prefetchable) [size=4K] Bus: primary=01, secondary=02, subordinate=05, sec-latency=176 Memory window 0: 40000000-43fff000 (prefetchable) Memory window 1: 48000000-4bfff000 I/O window 0: 0000e000-0000e0ff I/O window 1: 0000e400-0000e4ff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+ 16-bit legacy interface ports at 0001 Kernel driver in use: yenta_cardbus 01:01.1 FireWire (IEEE 1394) [0c00]: Texas Instruments PCI4510 IEEE-1394 Controller [104c:8029] (prog-if 10 [OHCI]) Subsystem: Dell Latitude D505 [1028:0163] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (500ns min, 1000ns max), Cache Line Size: 32 bytes Interrupt: pin B routed to IRQ 11 Region 0: Memory at fcfff800 (32-bit, non-prefetchable) [size=2K] Region 1: Memory at fcff8000 (32-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: firewire_ohci 01:08.0 Ethernet controller [0200]: Intel Corporation 82801DB PRO/100 VE (MOB) Ethernet Controller [8086:103d] (rev 81) Subsystem: Dell Latitude D500 [1028:2002] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (2000ns min, 14000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 11 Region 0: Memory at fcffe000 (32-bit, non-prefetchable) [size=4K] Region 1: I/O ports at ecc0 [size=64] Capabilities: <access denied> Kernel driver in use: e100 ** USB devices: Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 002: ID 0586:3401 ZyXEL Communications Corp. ZyAIR G-220 802.11bg Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub -- System Information: Debian Release: squeeze/sid APT prefers testing APT policy: (500, 'testing') Architecture: i386 (i686) Kernel: Linux 2.6.32-5-686 (SMP w/1 CPU core) Locale: LANG=fr_FR.utf8, LC_CTYPE=fr_FR.utf8 (charmap=UTF-8) Shell: /bin/sh linked to /bin/dash Versions of packages linux-image-2.6.32-5-686 depends on: ii debconf [debconf-2.0] 1.5.36 Debian configuration management sy ii initramfs-tools [linux-initra 0.98.5 tools for generating an initramfs ii linux-base 2.6.32-28 Linux image base package ii module-init-tools 3.12-1 tools for managing Linux kernel mo Versions of packages linux-image-2.6.32-5-686 recommends: ii firmware-linux-free 2.6.32-28 Binary firmware for various driver ii libc6-i686 2.11.2-7 Embedded GNU C Library: Shared lib Versions of packages linux-image-2.6.32-5-686 suggests: ii grub 0.97-63 GRand Unified Bootloader (dummy pa pn linux-doc-2.6.32 <none> (no description available) Versions of packages linux-image-2.6.32-5-686 is related to: pn firmware-bnx2 <none> (no description available) pn firmware-bnx2x <none> (no description available) ii firmware-ipw2x00 0.27 Binary firmware for Intel Pro Wire pn firmware-ivtv <none> (no description available) pn firmware-iwlwifi <none> (no description available) ii firmware-linux 0.27 Binary firmware for various driver ii firmware-linux-nonfree 0.27 Binary firmware for various driver pn firmware-qlogic <none> (no description available) pn firmware-ralink <none> (no description available) pn xen-hypervisor <none> (no description available) -- debconf information: linux-image-2.6.32-5-686/prerm/removing-running-kernel-2.6.32-5-686: true linux-image-2.6.32-5-686/postinst/depmod-error-initrd-2.6.32-5-686: false linux-image-2.6.32-5-686/postinst/ignoring-do-bootloader-2.6.32-5-686: * linux-image-2.6.32-5-686/postinst/missing-firmware-2.6.32-5-686:
--- End Message ---
--- Begin Message ---
- To: 606029-done@bugs.debian.org
- Subject: Re: Bug#606029: linux-image-2.6.32-5-686: cfg80211 or zd1211 incorrectly detects regdom or misses configuration dialog
- From: Ben Hutchings <ben@decadent.org.uk>
- Date: Sun, 05 Dec 2010 17:48:38 +0000
- Message-id: <1291571318.8025.86.camel@localhost>
- In-reply-to: <[🔎] 20101205173015.3375.1267.reportbug@josephine>
- References: <[🔎] 20101205173015.3375.1267.reportbug@josephine>
On Sun, 2010-12-05 at 18:30 +0100, Olivier Berger wrote: > Package: linux-2.6 > Version: 2.6.32-28 > Severity: normal > > Hi. > > Trying to connect to a wifi network (in France) which uses Channel 13 > fails with a USB network card which requires zd1211. > > It appears that after stock install, I have : > # cat /sys/module/cfg80211/parameters/ieee80211_regdom > 00 > > I need to set /etc/modprobe.d/cfg80211.conf with : > options cfg80211 ieee80211_regdom=EU > to make it work. > > I guess there's a bug here, which may be related to the lack of > debconf question for setting such parameters or similar configuration > mechanism prompting the user, or to a buggy automagic detection of the > regdom. > > In any case, it's far from obvious for non-expert user why some AP > would be seen (channels OK for US) and some not (for instance on > channels 12 and 13). This policy must be set by user-space, not the kernel. There is a package called crda which should do this, but for some reason people keep dithering and not uploading it (see bug #536502). Ben. -- Ben Hutchings Once a job is fouled up, anything done to improve it makes it worse.Attachment: signature.asc
Description: This is a digitally signed message part
--- End Message ---