Bug#605395: linux-image-2.6.32-5-amd64: JMicron Technology JMB362 JMB363 SError: { DevExch } ExpressCard, sometimes fails to boot
Package: linux-2.6
Version: 2.6.32-28
Severity: important
dmesg becomes completely filled with this message with only a couple of hours
uptime, the messages start to appear immediately after boot, sometimes whilst
booting.
If booting to a command prompt, the messages just keep filling up the terminal
every few seconds, making it really difficult to work this way.
ata3: irq_stat 0x00000040, connection status changed
[ 54.038441] ata3: SError: { DevExch }
[ 54.038457] ata3: limiting SATA link speed to 1.5 Gbps
[ 54.038465] ata3: hard resetting link
[ 55.688101] ata3: SATA link down (SStatus 0 SControl 310)
[ 55.688129] ata3: EH complete
[ 55.853985] ata3: exception Emask 0x10 SAct 0x0 SErr 0x4060000 action 0xe
frozen
Sometimes this happens at boot, and just stays in a loop, displaying this same
error on screen, removing the expresscard and reset solves the problem.
If I do have a successful boot and attach an ESATA drive to the card, it does
detect the drive after a few attempts, but I don't feel the device is safe
enough to use.
I have 2 of these expresscards, one is a dual port rev. 03 and one a single
port rev.02, they both exhibit the same behaviour.
Dual port
10:00.0 SATA controller: JMicron Technology Corp. JMB362/JMB363 Serial ATA
Controller (rev 03)
10:00.1 IDE interface: JMicron Technology Corp. JMB362/JMB363 Serial ATA
Controller (rev 03)
Single port
10:00.0 SATA controller: JMicron Technology Corp. JMB362/JMB363 Serial ATA
Controller (rev 02)
10:00.0 0106: 197b:2363 (rev 02)
They both share the same vend:dev ids.
The boot errors and the dmesg are happening without any esata drive attached /
having been attached.
-- Package-specific info:
** Version:
Linux version 2.6.32-5-amd64 (Debian 2.6.32-28) (ben@decadent.org.uk) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Thu Nov 25 18:02:11 UTC 2010
** Command line:
BOOT_IMAGE=/boot/vmlinuz-2.6.32-5-amd64 root=UUID=d6390ca6-c6f8-4191-98df-28b729f2de56 ro quiet splash
** Not tainted
** Kernel log:
[ 45.066454] ata3: limiting SATA link speed to 1.5 Gbps
[ 45.066463] ata3: hard resetting link
[ 46.173082] ata3: SATA link down (SStatus 0 SControl 310)
[ 46.173100] ata3: EH complete
[ 46.287405] ata3: exception Emask 0x10 SAct 0x0 SErr 0x4040000 action 0xe frozen
[ 46.287413] ata3: irq_stat 0x00000040, connection status changed
[ 46.287423] ata3: SError: { CommWake DevExch }
[ 46.287440] ata3: limiting SATA link speed to 1.5 Gbps
[ 46.287448] ata3: hard resetting link
[ 46.708055] wlan0: no IPv6 routers present
[ 47.520097] ata3: SATA link down (SStatus 0 SControl 310)
[ 47.520124] ata3: EH complete
[ 47.747578] ata3: exception Emask 0x10 SAct 0x0 SErr 0x4040000 action 0xe frozen
[ 47.747592] ata3: irq_stat 0x00000040, connection status changed
[ 47.747602] ata3: SError: { CommWake DevExch }
[ 47.747623] ata3: limiting SATA link speed to 1.5 Gbps
[ 47.747634] ata3: hard resetting link
[ 48.468099] ata3: SATA link down (SStatus 0 SControl 310)
[ 48.468119] ata3: EH complete
[ 48.499921] ata3: exception Emask 0x10 SAct 0x0 SErr 0x4040000 action 0xe frozen
[ 48.499929] ata3: irq_stat 0x00000040, connection status changed
[ 48.499938] ata3: SError: { CommWake DevExch }
[ 48.499954] ata3: limiting SATA link speed to 1.5 Gbps
[ 48.499964] ata3: hard resetting link
[ 49.220101] ata3: SATA link down (SStatus 0 SControl 310)
[ 49.220130] ata3: EH complete
[ 49.961372] ata3: exception Emask 0x10 SAct 0x0 SErr 0x4000000 action 0xe frozen
[ 49.961383] ata3: irq_stat 0x00000040, connection status changed
[ 49.961392] ata3: SError: { DevExch }
[ 49.961413] ata3: limiting SATA link speed to 1.5 Gbps
[ 49.961423] ata3: hard resetting link
[ 50.684083] ata3: SATA link down (SStatus 0 SControl 310)
[ 50.684101] ata3: EH complete
[ 51.411145] ata3: exception Emask 0x10 SAct 0x0 SErr 0x4000000 action 0xe frozen
[ 51.411153] ata3: irq_stat 0x00000040, connection status changed
[ 51.411162] ata3: SError: { DevExch }
[ 51.411177] ata3: limiting SATA link speed to 1.5 Gbps
[ 51.411184] ata3: hard resetting link
[ 52.324089] ata3: SATA link down (SStatus 0 SControl 310)
[ 52.324109] ata3: EH complete
[ 52.344738] ata3: exception Emask 0x10 SAct 0x0 SErr 0x4000000 action 0xe frozen
[ 52.344747] ata3: irq_stat 0x00000040, connection status changed
[ 52.344756] ata3: SError: { DevExch }
[ 52.344771] ata3: limiting SATA link speed to 1.5 Gbps
[ 52.344779] ata3: hard resetting link
[ 53.068094] ata3: SATA link down (SStatus 0 SControl 310)
[ 53.068109] ata3: EH complete
[ 53.069723] ata3: exception Emask 0x10 SAct 0x0 SErr 0x4040000 action 0xe frozen
[ 53.069730] ata3: irq_stat 0x00000040, connection status changed
[ 53.069739] ata3: SError: { CommWake DevExch }
[ 53.069753] ata3: limiting SATA link speed to 1.5 Gbps
[ 53.069760] ata3: hard resetting link
[ 53.792094] ata3: SATA link down (SStatus 0 SControl 310)
[ 53.792123] ata3: EH complete
[ 54.038424] ata3: exception Emask 0x10 SAct 0x0 SErr 0x4000000 action 0xe frozen
[ 54.038433] ata3: irq_stat 0x00000040, connection status changed
[ 54.038441] ata3: SError: { DevExch }
[ 54.038457] ata3: limiting SATA link speed to 1.5 Gbps
[ 54.038465] ata3: hard resetting link
[ 55.688101] ata3: SATA link down (SStatus 0 SControl 310)
[ 55.688129] ata3: EH complete
[ 55.853985] ata3: exception Emask 0x10 SAct 0x0 SErr 0x4060000 action 0xe frozen
[ 55.853998] ata3: irq_stat 0x00000040, connection status changed
[ 55.854007] ata3: SError: { PHYInt CommWake DevExch }
[ 55.854029] ata3: limiting SATA link speed to 1.5 Gbps
[ 55.854040] ata3: hard resetting link
[ 56.960095] ata3: SATA link down (SStatus 0 SControl 310)
[ 56.960117] ata3: EH complete
[ 56.967123] ata3: exception Emask 0x10 SAct 0x0 SErr 0x4040000 action 0xe frozen
[ 56.967134] ata3: irq_stat 0x00000040, connection status changed
[ 56.967143] ata3: SError: { CommWake DevExch }
[ 56.967161] ata3: limiting SATA link speed to 1.5 Gbps
[ 56.967170] ata3: hard resetting link
[ 59.192077] ata3: COMRESET failed (errno=-32)
[ 59.192095] ata3: reset failed (errno=-32), retrying in 8 secs
[ 66.968071] ata3: hard resetting link
[ 69.252056] ata3: COMRESET failed (errno=-32)
[ 69.252073] ata3: reset failed (errno=-32), retrying in 8 secs
[ 76.964080] ata3: hard resetting link
[ 79.032142] ata3: SATA link down (SStatus 0 SControl 310)
[ 79.032171] ata3: EH complete
[ 79.041056] ata3: exception Emask 0x10 SAct 0x0 SErr 0x4060000 action 0xe frozen
[ 79.041066] ata3: irq_stat 0x00000040, connection status changed
[ 79.041075] ata3: SError: { PHYInt CommWake DevExch }
[ 79.041097] ata3: limiting SATA link speed to 1.5 Gbps
[ 79.041107] ata3: hard resetting link
[ 81.304104] ata3: COMRESET failed (errno=-32)
[ 81.304123] ata3: reset failed (errno=-32), retrying in 8 secs
[ 89.040100] ata3: hard resetting link
[ 91.269075] ata3: COMRESET failed (errno=-32)
[ 91.269092] ata3: reset failed (errno=-32), retrying in 8 secs
[ 99.040101] ata3: hard resetting link
[ 101.272074] ata3: COMRESET failed (errno=-32)
[ 101.272092] ata3: reset failed (errno=-32), retrying in 33 secs
[ 134.040082] ata3: hard resetting link
[ 136.268080] ata3: COMRESET failed (errno=-32)
[ 136.268098] ata3: reset failed, giving up
[ 136.268112] ata3: EH complete
[ 972.144826] reportbug[2954] trap divide error ip:7f06248abcf0 sp:7f061d326f60 error:0 in libgtk-x11-2.0.so.0.2000.1[7f062477f000+415000]
[ 1009.167907] reportbug[3015]: segfault at 8 ip 00000000004c6e07 sp 00007f63dc36f500 error 4 in python2.6[400000+21d000]
** Model information
sys_vendor: Hewlett-Packard
product_name: HP Compaq nx6325 (EY351ET#ABU)
product_version: F.07
chassis_vendor: Hewlett-Packard
chassis_version:
bios_vendor: Hewlett-Packard
bios_version: 68TT2 Ver. F.07
board_vendor: Hewlett-Packard
board_name: 30B0
board_version: KBC Version 40.15
** Loaded modules:
Module Size Used by
powernow_k8 10978 1
cpufreq_stats 2659 0
cpufreq_conservative 5162 0
cpufreq_powersave 902 0
cpufreq_userspace 1992 0
parport_pc 18855 0
ppdev 5030 0
lp 7462 0
parport 27954 3 parport_pc,ppdev,lp
sco 7209 2
bridge 39630 0
stp 1440 1 bridge
bnep 9427 2
rfcomm 29597 0
l2cap 24736 6 bnep,rfcomm
bluetooth 41827 6 sco,bnep,rfcomm,l2cap
uinput 6376 1
fuse 50273 1
loop 11799 0
snd_hda_codec_analog 64562 1
snd_hda_intel 19987 1
snd_hda_codec 54244 2 snd_hda_codec_analog,snd_hda_intel
snd_hwdep 5380 1 snd_hda_codec
snd_pcm 60503 2 snd_hda_intel,snd_hda_codec
arc4 1274 2
snd_seq 42881 0
snd_timer 15582 2 snd_pcm,snd_seq
snd_seq_device 4493 1 snd_seq
ecb 1841 2
snd 46446 10 snd_hda_codec_analog,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_seq,snd_timer,snd_seq_device
joydev 8459 0
b43 146172 0
rng_core 3006 1 b43
soundcore 4598 1 snd
snd_page_alloc 6249 2 snd_hda_intel,snd_pcm
mac80211 137340 1 b43
edac_core 29261 0
cfg80211 101496 2 b43,mac80211
rfkill 13044 3 bluetooth,cfg80211
yenta_socket 19115 1
tpm_infineon 7499 0
edac_mce_amd 6433 0
evdev 7352 20
psmouse 49777 0
container 2389 0
battery 4998 0
ac 2192 0
k8temp 3283 0
pcspkr 1699 0
rsrc_nonstatic 7294 1 yenta_socket
tpm 9917 1 tpm_infineon
i2c_piix4 8328 0
tifm_7xx1 3850 0
tifm_core 4340 1 tifm_7xx1
tpm_bios 4521 1 tpm
serio_raw 3752 0
wmi 4323 0
shpchp 26264 0
processor 29935 1 powernow_k8
pci_hotplug 21203 1 shpchp
ext4 289033 1
mbcache 5050 1 ext4
jbd2 67015 1 ext4
crc16 1319 2 l2cap,ext4
usbhid 33292 0
hid 63145 1 usbhid
sg 18744 0
radeon 573596 2
sd_mod 29889 3
crc_t10dif 1276 1 sd_mod
sr_mod 12602 0
cdrom 29415 1 sr_mod
ttm 39986 1 radeon
drm_kms_helper 20065 1 radeon
sdhci_pci 5581 0
ssb 38666 1 b43
ata_generic 3015 0
fan 3346 0
pcmcia 19474 2 b43,ssb
sdhci 13966 1 sdhci_pci
sata_sil 7412 2
tg3 95663 0
pata_jmicron 2280 0
ahci 32374 0
video 17445 0
ohci_hcd 19212 0
drm 142359 4 radeon,ttm,drm_kms_helper
i2c_algo_bit 4225 1 radeon
mmc_core 45686 3 b43,ssb,sdhci
led_class 2433 2 b43,sdhci
libphy 14054 1 tg3
pata_atiixp 3489 0
libata 133616 5 ata_generic,sata_sil,pata_jmicron,ahci,pata_atiixp
output 1692 1 video
ehci_hcd 31135 0
pcmcia_core 24118 5 b43,yenta_socket,rsrc_nonstatic,ssb,pcmcia
usbcore 122034 4 usbhid,ohci_hcd,ehci_hcd
i2c_core 15712 5 i2c_piix4,radeon,drm_kms_helper,drm,i2c_algo_bit
scsi_mod 122149 4 sg,sd_mod,sr_mod,libata
nls_base 6377 1 usbcore
thermal 11674 0
thermal_sys 11942 4 processor,fan,video,thermal
button 4650 0
** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
#allow-hotplug eth0
#iface eth0 inet dhcp
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN qlen 1000
link/ether 00:17:a4:d6:bf:87 brd ff:ff:ff:ff:ff:ff
3: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000
link/ether 00:1a:73:1f:78:53 brd ff:ff:ff:ff:ff:ff
inet 192.168.0.5/24 brd 192.168.0.255 scope global wlan0
inet6 fe80::21a:73ff:fe1f:7853/64 scope link
valid_lft forever preferred_lft forever
4: pan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN
link/ether 0a:1f:55:1c:dc:ed brd ff:ff:ff:ff:ff:ff
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed
lo: 976 12 0 0 0 0 0 0 976 12 0 0 0 0 0 0
eth0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
wlan0: 497529 785 0 0 0 0 0 0 159496 957 0 0 0 0 0 0
pan0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
*** Protocol statistics:
Ip:
897 total packets received
0 forwarded
0 incoming packets discarded
897 incoming packets delivered
932 requests sent out
75 dropped because of missing route
Icmp:
1 ICMP messages received
0 input ICMP message failed.
ICMP input histogram:
echo replies: 1
1 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
echo request: 1
IcmpMsg:
InType0: 1
OutType8: 1
Tcp:
50 active connections openings
0 passive connection openings
1 failed connection attempts
1 connection resets received
0 connections established
584 segments received
654 segments send out
1 segments retransmited
0 bad segments received.
15 resets sent
Udp:
271 packets received
0 packets to unknown port received.
0 packet receive errors
267 packets sent
UdpLite:
TcpExt:
48 delayed acks sent
5 packets directly queued to recvmsg prequeue.
1603 bytes directly received in process context from prequeue
297 packet headers predicted
100 acknowledgments not containing data payload received
1 other TCP timeouts
1 connections reset due to unexpected data
1 connections reset due to early user close
IpExt:
InMcastPkts: 62
OutMcastPkts: 26
InBcastPkts: 98
OutBcastPkts: 98
InOctets: 507838
OutOctets: 124130
InMcastOctets: 4417
OutMcastOctets: 3281
InBcastOctets: 18091
OutBcastOctets: 18091
*** Device features:
eth0: 0x983
lo: 0x13865
pan0: 0xff3865
wlan0: 0x2000
** PCI devices:
00:00.0 Host bridge [0600]: ATI Technologies Inc RS480 Host Bridge [1002:5950] (rev 10)
Subsystem: Hewlett-Packard Company Device [103c:30b0]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 64
00:01.0 PCI bridge [0604]: ATI Technologies Inc RS480 PCI Bridge [1002:5a3f] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00005000-00005fff
Memory behind bridge: d0400000-d04fffff
Prefetchable memory behind bridge: 00000000c0000000-00000000c7ffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:04.0 PCI bridge [0604]: ATI Technologies Inc RS480 PCI Bridge [1002:5a36] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=10, subordinate=10, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: d0000000-d00fffff
Prefetchable memory behind bridge: 0000000084000000-00000000840fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:05.0 PCI bridge [0604]: ATI Technologies Inc RS480 PCI Bridge [1002:5a37] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=20, subordinate=20, sec-latency=0
I/O behind bridge: 00002000-00003fff
Memory behind bridge: cc000000-cfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:06.0 PCI bridge [0604]: ATI Technologies Inc RS480 PCI Bridge [1002:5a38] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=30, subordinate=30, sec-latency=0
Memory behind bridge: c8000000-c80fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:12.0 IDE interface [0101]: ATI Technologies Inc IXP SB400 Serial ATA Controller [1002:4379] (rev 80) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Hewlett-Packard Company Device [103c:30b0]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 9000 [size=8]
Region 1: I/O ports at 9008 [size=4]
Region 2: I/O ports at 9010 [size=8]
Region 3: I/O ports at 6018 [size=4]
Region 4: I/O ports at 6020 [size=16]
Region 5: Memory at d0509000 (32-bit, non-prefetchable) [size=512]
[virtual] Expansion ROM at 84100000 [disabled] [size=512K]
Capabilities: <access denied>
Kernel driver in use: sata_sil
00:13.0 USB Controller [0c03]: ATI Technologies Inc IXP SB400 USB Host Controller [1002:4374] (rev 80) (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company Device [103c:30b0]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at d0501000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:13.1 USB Controller [0c03]: ATI Technologies Inc IXP SB400 USB Host Controller [1002:4375] (rev 80) (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company Device [103c:30b0]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at d0502000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:13.2 USB Controller [0c03]: ATI Technologies Inc IXP SB400 USB2 Host Controller [1002:4373] (rev 80) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Device [103c:30b0]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at d0503000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:14.0 SMBus [0c05]: ATI Technologies Inc IXP SB400 SMBus Controller [1002:4372] (rev 82)
Subsystem: Hewlett-Packard Company Device [103c:30b0]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: I/O ports at 8200 [size=16]
Region 1: Memory at d0504000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: piix4_smbus
00:14.1 IDE interface [0101]: ATI Technologies Inc IXP SB400 IDE Controller [1002:4376] (rev 80) (prog-if 82 [Master PriP])
Subsystem: Hewlett-Packard Company Device [103c:30b0]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 6040 [size=16]
Capabilities: <access denied>
Kernel driver in use: pata_atiixp
00:14.2 Audio device [0403]: ATI Technologies Inc IXP SB4x0 High Definition Audio Controller [1002:437b] (rev 01)
Subsystem: Device [30b0:103c]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin ? routed to IRQ 16
Region 0: Memory at 84180000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
00:14.3 ISA bridge [0601]: ATI Technologies Inc IXP SB400 PCI-ISA Bridge [1002:4377] (rev 80)
Subsystem: Hewlett-Packard Company Device [103c:30b0]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:14.4 PCI bridge [0604]: ATI Technologies Inc IXP SB400 PCI-PCI Bridge [1002:4371] (rev 80) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=02, subordinate=06, sec-latency=64
I/O behind bridge: 00001000-00001fff
Memory behind bridge: d0100000-d03fffff
Prefetchable memory behind bridge: 80000000-83ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map [1022:1101]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller [1022:1102]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control [1022:1103]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
Kernel driver in use: k8temp
01:05.0 VGA compatible controller [0300]: ATI Technologies Inc RS482 [Radeon Xpress 200M] [1002:5975] (prog-if 00 [VGA controller])
Subsystem: Hewlett-Packard Company Device [103c:30b0]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B+ DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (2000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at c0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 5000 [size=256]
Region 2: Memory at d0400000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at d0420000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: radeon
02:01.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5788 Gigabit Ethernet [14e4:169c] (rev 03)
Subsystem: Hewlett-Packard Company Device [103c:30b0]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (16000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 23
Region 0: Memory at d0100000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at <ignored> [disabled]
Capabilities: <access denied>
Kernel driver in use: tg3
02:04.0 CardBus bridge [0607]: Texas Instruments PCIxx12 Cardbus Controller [104c:8039]
Subsystem: Hewlett-Packard Company Device [103c:30b0]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 20
Region 0: Memory at d0110000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
Memory window 0: 80000000-83fff000 (prefetchable)
Memory window 1: 88000000-8bfff000
I/O window 0: 00001000-000010ff
I/O window 1: 00001400-000014ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
02:04.2 Mass storage controller [0180]: Texas Instruments 5-in-1 Multimedia Card Reader (SD/MMC/MS/MS PRO/xD) [104c:803b]
Subsystem: Hewlett-Packard Company Device [103c:30b0]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (1750ns min, 1000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 20
Region 0: Memory at d0118000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: tifm_7xx1
02:04.3 SD Host controller [0805]: Texas Instruments PCIxx12 SDA Standard Compliant SD Host Controller [104c:803c]
Subsystem: Hewlett-Packard Company Device [103c:30b0]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (1750ns min, 1000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 20
Region 0: Memory at d0119000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: sdhci-pci
10:00.0 SATA controller [0106]: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller [197b:2363] (rev 03) (prog-if 01 [AHCI 1.0])
Subsystem: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller [197b:2363]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 5: Memory at d0000000 (32-bit, non-prefetchable) [size=8K]
[virtual] Expansion ROM at 84000000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: ahci
10:00.1 IDE interface [0101]: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller [197b:2363] (rev 03) (prog-if 85 [Master SecO PriO])
Subsystem: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller [197b:2363]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at 4000 [size=8]
Region 1: I/O ports at 4008 [size=4]
Region 2: I/O ports at 4010 [size=8]
Region 3: I/O ports at 4018 [size=4]
Region 4: I/O ports at 4020 [size=16]
Capabilities: <access denied>
Kernel driver in use: pata_jmicron
30:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11a/b/g [14e4:4312] (rev 01)
Subsystem: Hewlett-Packard Company Broadcom 802.11a/b/g WLAN [103c:1361]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at c8000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: b43-pci-bridge
** USB devices:
Bus 003 Device 002: ID 08ff:2580 AuthenTec, Inc. AES2501 Fingerprint Sensor
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 002: ID 15d9:0a4c Trust International B.V.
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 004: ID 0409:0059 NEC Corp. HighSpeed Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: squeeze/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.32-5-amd64 (SMP w/2 CPU cores)
Locale: LANG=en_GB.UTF-8, LC_CTYPE=en_GB.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-2.6.32-5-amd64 depends on:
ii debconf [debconf-2.0] 1.5.36 Debian configuration management sy
ii initramfs-tools [linux-initra 0.98.5 tools for generating an initramfs
ii linux-base 2.6.32-28 Linux image base package
ii module-init-tools 3.12-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.32-5-amd64 recommends:
ii firmware-linux-free 2.6.32-28 Binary firmware for various driver
Versions of packages linux-image-2.6.32-5-amd64 suggests:
pn grub | lilo <none> (no description available)
pn linux-doc-2.6.32 <none> (no description available)
Versions of packages linux-image-2.6.32-5-amd64 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
ii firmware-linux 0.27 Binary firmware for various driver
ii firmware-linux-nonfree 0.27 Binary firmware for various driver
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn xen-hypervisor <none> (no description available)
-- debconf information:
linux-image-2.6.32-5-amd64/postinst/depmod-error-initrd-2.6.32-5-amd64: false
linux-image-2.6.32-5-amd64/prerm/removing-running-kernel-2.6.32-5-amd64: true
linux-image-2.6.32-5-amd64/postinst/missing-firmware-2.6.32-5-amd64:
linux-image-2.6.32-5-amd64/postinst/ignoring-do-bootloader-2.6.32-5-amd64:
Reply to: