Bug#603927: linux-image-2.6.32-5-xen-686: booting with xen enabled fails to bring up ATA devices
Hi Micah,
I am assuming that this the same issue as you reported on xen-devel in
the "aic79xx failures with pvops dom0 2.6.32.25"[0] / "ATA driver
failures with pvops dom0"[1] thread recently?
If not please let me know otherwise I'll just monitor that thread,
although please let this ticket know if you reach a resolution on the
list.
Thanks,
Ian.
[0] http://lists.xensource.com/archives/html/xen-devel/2010-11/msg01228.html
[1] http://lists.xensource.com/archives/html/xen-devel/2010-11/msg01310.html
On Thu, 2010-11-18 at 10:23 -0500, Micah Anderson wrote:
> Package: linux-2.6
> Version: 2.6.32-27
> Severity: normal
>
> If I boot the linux-image-2.6.32-5-xen-686 kernel without Xen (ie. without the
> "multiboot /xen-4.0-i386.gz" option set in grub, things boot fine. If I add
> that line, the system fails to bring up the ATA devices properly, and it gets
> stuck in some crazy loop.
>
> The boot messages from the functioning kernel are attached below, the boot
> messages from when Xen is enabled are as follows (note: at some point I had
> to stop things):
>
> [ 0.000000] Reserving virtual address space above 0xf5800000
> [ 0.000000] Initializing cgroup subsys cpuset
> [ 0.000000] Initializing cgroup subsys cpu
> [ 0.000000] Linux version 2.6.32-5-xen-686 (Debian 2.6.32-27) AuthenticAMD
> [ 00] Cyrix Cyriges of unused memory
> [ 0.000000] BIOS-provided physical RAM map:
> [ 0.000000] Xen: 0000000000000000 - 000000000009f800 (usable)
> [ 0.000000] Xen: 000000000009f800 - 0000000000100000 (reserved)
> [ 0.000000] Xen: 0000000000100000 - 0000000020000000 (usable)
> [ 0.000000] Xen: 00000000f7ef9000 - 00000000f7f00000 (ACPI NVS)
> [ 0.000000] Xen: 00000000f7f80000 - 00000000f8000000 (reserved)
> [ 0.000000] Xen: 00000000fec00000 - 00000000fec10000 (reserved)
> [ 0.000000] Xen: 00000000fec80000 - 00000000fec81000 (reserved)
> [ 0.000000] Xen: 00000000fee00000 - 00000000fee01000 (reserved)
> [ 0.000000] Xen: 00000000ff800000 - 00000000ffc00000 (reserved)
> [ 0.000000] Xen: 00000000fff00000 - 0000000100000000 (reserved)
> [ 0.000000] DMI present.
> [ 0.000000] Phoenix BIOS detected: BIOS may corrupt low RAM, working around it.
> [ 0.000000] last_pfn = 0x20000 max_arch_pfn = 0x1000000
> [ 0.000000] x86 PAT enabled: cpu 0, old 0x50100070406, new 0x7010600070106
> [ 0.000000] init_memory_mapping: 0000000000000000-0000000020000000
> [ 0.000000] RAMDISK: 0164c000 - 02e0de00
> [ 0.000000] ACPI Error: A valid RSDP was not found (20090903/tbxfroot-219)
> [ 0.000000] 0MB HIGHMEM available.
> [ 0.000000] 512MB LOWMEM available.
> [ 0.000000] mapped low ram: 0 - 20000000
> [ 0.000000] low ram: 0 - 20000000
> [ 0.000000] node 0 low ram: 00000000 - 20000000
> [ 0.000000] node 0 bootmap 00010000 - 00014000
> [ 0.000000] (10 early reservations) ==> bootmem [0000000000 - 0020000000]
> [ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
> [ 0.000000] #1 [0002e8f000 - 0002eac000] XEN PAGETABLES ==> [0002e8f000 - 0002eac000]
> [ 0.000000] #2 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
> [ 0.000000] #3 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
> [ 0.000000] #4 [0001000000 - 00015268d4] TEXT DATA BSS ==> [0001000000 - 00015268d4]
> [ 0.000000] #5 [000164c000 - 0002e0de00] RAMDISK ==> [000164c000 - 0002e0de00]
> [ 0.000000] #6 [0002e0e000 - 0002e8f000] XEN START INFO ==> [0002e0e000 - 0002e8f000]
> [ 0.000000] #7 [0001527000 - 0001527114] BRK ==> [0001527000 - 0001527114]
> [ 0.000000] #8 [0000100000 - 00001e7000] PGTABLE ==> [0000100000 - 00001e7000]
> [ 0.000000] #9 [0000010000 - 0000014000] BOOTMAP ==> [0000010000 - 0000014000]
> [ 0.000000] found SMP MP-table at [c00f6ca0] f6ca0
> [ 0.000000] Zone PFN ranges:
> [ 0.000000] DMA 0x00000010 -> 0x00001000
> [ 0.000000] Normal 0x00001000 -> 0x00020000
> [ 0.000000] HighMem 0x00020000 -> 0x00020000
> [ 0.000000] Movable zone start PFN for each node
> [ 0.000000] early_node_map[2] active PFN ranges
> [ 0.000000] 0: 0x00000010 -> 0x0000009f
> [ 0.000000] 0: 0x00000100 -> 0x00020000
> [ 0.000000] Using APIC driver default
> [ 0.000000] SFI: Simple Firmware Interface v0.7 http://simplefirmware.org
> [ 0.000000] Intel MultiProcessor Specification v1.4
> [ 0.000000] Virtual Wire compatibility mode.
> [ 0.000000] MPTABLE: OEM ID:
> [ 0.000000] MPTABLE: Product ID: Kings Canyon
> [ 0.000000] MPTABLE: APIC at: 0xFEE00000
> [ 0.000000] I/O APIC #2 Version 32 at 0xFEC00000.
> [ 0.000000] I/O APIC #3 Version 32 at 0xFEC80000.
> [ 0.000000] I/O APIC #4 Version 32 at 0xFEC80400.
> [ 0.000000] Processors: 1
> [ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs
> [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
> [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 0000000000100000
> [ 0.000000] Allocating PCI resources starting at 20000000 (gap: 20000000:d7ef9000)
> [ 0.000000] Booting paravirtualized kernel on Xen
> [ 0.000000] Xen version: 4.0.1 (preserve-AD) (dom0)
> [ 0.000000] NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:1 nr_node_ids:1
> [ 0.000000] PERCPU: Embedded 15 pages/cpu @c32b0000 s37656 r0 d23784 u65536
> [ 0.000000] pcpu-alloc: s37656 r0 d23784 u65536 alloc=16*4096
> [ 0.000000] pcpu-alloc: [0] 0
> [ 0.000000] Xen: using vcpu_info placement
> [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129935
> [ 0.000000] Kernel command line: placeholder root=/dev/mapper/quelea0-root ro console=tty0 console=ttyS0,115200n8
> [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
> [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
> [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
> [ 0.000000] Enabling fast FPU save and restore... done.
> [ 0.000000] Enabling unmasked SIMD FPU exception support... done.
> [ 0.000000] Initializing CPU#0
> [ 0.000000] DMA: Placing 64MB software IO TLB between c3322000 - c7322000
> [ 0.000000] DMA: software IO TLB at phys 0x3322000 - 0x7322000
> [ 0.000000] xen_swiotlb_fixup: buf=c3322000 size=67108864
> [ 0.000000] xen_swiotlb_fixup: buf=c7382000 size=32768
> [ 0.000000] Initializing HighMem for node 0 (00000000:00000000)
> [ 0.000000] Memory: 421776k/524288k available (2631k kernel code, 101704k reserved, 1450k data, 396k init, 0k highmem)
> [ 0.000000] virtual kernel memory layout:
> [ 0.000000] fixmap : 0xf5556000 - 0xf57ff000 (2724 kB)
> [ 0.000000] pkmap : 0xf5000000 - 0xf5200000 (2048 kB)
> [ 0.000000] vmalloc : 0xe0800000 - 0xf4ffe000 ( 327 MB)
> [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
> [ 0.000000] .init : 0xc13fd000 - 0xc1460000 ( 396 kB)
> [ 0.000000] .data : 0xc1291e51 - 0xc13fc998 (1450 kB)
> [ 0.000000] .text : 0xc1000000 - 0xc1291e51 (2631 kB)
> [ 0.000000] SLUB: Genslabs=13, HWalign=128, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
> [ 0.000000] Hierarchical RCU implementation.
> [ 0.000000] NR_IRQS:1536
> [ 0.000000] Console: colour VGA+ 80x25
> [ 0.000000] console [tty0] enabled
> [ 0.000000] console [ttyS0] enabled
> [ 0.000000] installing Xen timer for CPU 0
> [ 0.000000] Detected 3199.098 MHz processor.
> [ 0.004000] Calibrating delay loop (skipped), value calculated using timer frequency.. 6398.19 BogoMIPS (lpj=12796392)
> [ 0.004000] Security Framework initialized
> [ 0.004000] SELinux: Disabled at boot.
> [ 0.004000] Mount-cache hash table entries: 512
> [ 0.004270] Initializing cgroup subsys ns
> [ 0.008000] Initializing cgroup subsys cpuacct
> [ 0.008000] Initializing cgroup subsys devices
> [ 0.008000] Initializing cgroup subsys freezer
> [ 0.008000] Initializing cgroup subsys net_cls
> [ 0.008037] CPU: Trace cache: 12K uops, L1 D cache: 8K
> [ 0.012000] CPU: L2 cache: 512K
> [ 0.012000] CPU: L3 cache: 1024K
> [ 0.012010] CPU: Unsupported number of siblings 2
> [ 0.016013] mce: CPU supports 4 MCE banks
> [ 0.020039] Performance Events: no PMU driver, software events only.
> [ 0.024949] SMP alternatives: switching to UP code
> [ 0.028001] Freeing SMP alternatives: 14k freed
> [ 0.028468] Brought up 1 CPUs
> [ 0.031772] devtmpfs: initialized
> [ 0.032844] Grant table initialized
> [ 0.036001] regulator: core version 0.5
> [ 0.036095] NET: Registered protocol family 16
> [ 0.042081] PCI: PCI BIOS revision 2.10 entry at 0xfd8c5, last bus=4
> [ 0.044001] PCI: Using configuration type 1 for base access
> [ 0.044855] bio: create slab <bio-0> at 0
> [ 0.048134] ACPI: Interpreter disabled.
> [ 0.052141] xen_balloon: Initialising balloon driver with page order 0.
> [ 0.056065] vgaarb: loaded
> [ 0.058974] PCI: Probing PCI hardware
> [ 0.061236] pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
> [ 0.064001] pci 0000:00:1f.0: quirk: region 1180-11bf claimed by ICH4 GPIO
> [ 0.064644] pci 0000:02:03.0: PME# supported from D0 D3hot D3cold
> [ 0.068001] pci 0000:02:03.0: PME# disabled
> [ 0.068001] pci 0000:02:03.1: PME# supported from D0 D3hot D3cold
> [ 0.068001] pci 0000:02:03.1: PME# disabled
> [ 0.068001] pci 0000:00:1e.0: transparent bridge
> [ 0.068802] vgaarb: device added: PCI:0000:04:01.0,decodes=io+mem,owns=io+mem,locks=none
> [ 0.072213] PCI: Discovered primary peer bus 10 [IRQ]
> [ 0.076158] PCI: Discovered primary peer bus 11 [IRQ]
> [ 0.080001] PCI: Discovered primary peer bus 12 [IRQ]
> [ 0.080001] pci 0000:00:1f.0: PIIX/ICH IRQ router [8086:2480]
> [ 0.080010] pci 0000:00:1f.1: found PCI INT A -> IRQ 7
> [ 0.084051] Switching to clocksource xen
> [ 0.090871] pnp: PnP ACPI: disabled
> [ 0.092001] PnPBIOS: Disabled
> [ 0.098142] pci 0000:01:1d.0: PCI bridge, secondary bus 0000:02
> [ 0.101452] pci 0000:01:1d.0: IO window: 0x3000-0x3fff
> [ 0.101452] pci 0000:01:1d.0: MEM window: 0xfc200000-0xfc7fffff
> [ 0.101452] pci 0000:01:1d.0: PREFETCH window: disabled
> [ 0.101452] pci 0000:01:1f.0: PCI bridge, secondary bus 0000:03
> [ 0.101452] pci 0000:01:1f.0: IO window: 0x4000-0x4fff
> [ 0.101452] pci 0000:01:1f.0: MEM window: 0xfc800000-0xfc8fffff
> [ 0.101452] pci 0000:01:1f.0: PREFETCH window: 0x20000000-0x200fffff
> [ 0.101452] pci 0000:00:02.0: PCI bridge, secondary bus 0000:01
> [ 0.101452] pci 0000:00:02.0: IO window: 0x3000-0x4fff
> [ 0.101452] pci 0000:00:02.0: MEM window: 0xfc100000-0xfc8fffff
> [ 0.101452] pci 0000:00:02.0: PREFETCH window: 0x20000000-0x200fffff
> [ 0fff
> [ 0.10145es)
> [ 0.206200ed (established 1ed
> [ 0.343095] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
> [ 0.344020] DMA: Placing 64MB software IO TLB between c3322000 - c7322000
> [ 0.344020] DMA: software IO TLB at phys 0x3322000 - 0x7322000
> [ 0.362585] platform rtc_cmos: registered platform RTC device (no PNP device found)
> [ 0.370987] audit: initializing netlink socket (disabled)
> [ 0.376498] type=2000 audit(1290053841.119:1): initialized
> [ 0.385030] HugeTLB registered 2 MB page size, pre-allocated 0 pages
> [ 0.393778] VFS: Disk quotas dquot_6.5.2
> [ 0.396007] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
> [ 0.404574] msgmni has been set to 872
> [ 0.408762] alg: No test for stdrng (krng)
> [ 0.413043] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
> [ 0.416944] io scheduler noop registered
> [ 0.416944] io scheduler anticipatory registered
> [ 0.416944] io scheduler deadline registered
> [ 0.433670] io scheduler cfq registered (default)
> [ 0.438922] isapnp: Scanning for PnP cards...
> [ 0.800386] isapnp: No Plug & Play device found
> [ 0.813321] registering netback
> [ 0.819572] Linux agpgart interface v0.103
> [ 0.823976] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
> ÿ[ 0.830529] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> [ 0.834337] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
> [ 0.843200] PNP: No PS/2 controller found. Probing ports directly.
> [ 1.100406] serio: i8042 KBD port at 0x60,0x64 ires nvram
> [ 1.1otocol family 10
> [ 1.143058] lo: Disabled Privacy Extensions
> [ 1.147643] Mobile IPv6
> [ 1.150171] NET: Registered protocol family 17
> [ 1.154730] Using IPI No-Shortcut mode
> [ 1.158714] registered taskstats version 1
> [ 1.163623] rtc_cmos rtc_cmos: setting system clock to 2010-11-18 04:17:21 UTC (1290053841)
> [ 1.172121] Initalizing network drop monitor service
> [ 1.177224] Freeing unused kernel memory: 396k freed
> [ 1.183969] Write protecting the kernel text: 2632k
> [ 1.189426] Write protecting the kernel read-only data: 968k
> Loading, please wait...
> [ 1.248326] udev[48]: starting version 163
> [ 1.499041] usbcore: registered new interface driver usbfs
> [ 1.505529] usbcore: registered new interface driver hub
> [ 1.511815] usbcore: registered new device driver usb
> [ 1.523928] SCSI subsystem initialized
> [ 1.550684] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
> [ 1.569853] Intel(R) PRO/1000 Network Driver - version 7.3.21-k5-NAPI
> [ 1.572012] Copyright (c) 1999-2006 Intel Corporation.
> [ 1.592728] uhci_hcd: USB Universal Host Controller Interface driver
> [ 1.611113] aic79xx 0000:03:02.0: found PCI INT A -> IRQ 5
> [ 1.612030] aic79xx 0000:03:02.0: sharing IRQ 5 with 0000:02:01.0
> [ 1.612030] aic79xx 0000:03:02.0: sharing IRQ 5 with 0000:02:03.0
> [ 1.612030] aic79xx 0000:03:02.0: sharing IRQ 5 with 0000:02:03.1
> [ 1.612030] aic79xx 0000:03:02.0: sharing IRQ 5 with 0000:03:02.1
> [ 1.757200] uhci_hcd 0000:00:1d.0: found PCI INT A -> IRQ 11
> [ 1.760007] uhci_hcd 0000:00:1d.0: sharing IRQ 11 with 0000:04:01.0
> [ 1.760007] uhci_hcd 0000:00:1d.0: UHCI Host Controller
> [ 1.760007] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
> [ 1.784562] e1000 0000:02:03.0: found PCI INT A -> IRQ 5
> [ 1.788461] e1000 0000:02:03.0: sharing IRQ 5 with 0000:02:01.0
> [ 1.788461] e1000 0000:02:03.0: sharing IRQ 5 with 0000:02:03.1
> [ 1.788461] e1000 0000:02:03.0: sharing IRQ 5 with 0000:03:02.0
> [ 1.788461] e1000 0000:02:03.0: sharing IRQ 5 with 0000:03:02.1
> [ 1.816751] uhci_hcd 0000:00:1d.0: request interrupt 11 failed
> [ 1.820544] uhci_hcd 0000:00:1d.0: USB bus 1 deregistered
> [ 1.820544] uhci_hcd 0000:00:1d.0: init 0000:00:1d.0 fail, -38
> [ 1.820544] uhci_hcd: probe of 0000:00:1d.0 failed with error -38
> [ 1.842416] ata_piix 0000:00:1f.1: found PCI INT A -> IRQ 7
> [ 1.849013] scsi0 : ata_piix
> [ 1.852664] scsi1 : ata_piix
> [ 1.856158] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x2060 irq 14
> [ 1.860011] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x2068 irq 15
> [ 1.872469] uhci_hcd 0000:00:1d.1: UHCI Host Controller
> [ 1.876010] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 1
> [ 2.132556] e1000: 0000:02:03.0: e1000_probe: (PCI-X:133MHz:64-bit) 00:30:48:2d:3e:d2
> [ 2.142147] uhci_hcd 0000:00:1d.1: request interrupt 10 failed
> [ 2.145264] uhci_hcd 0000:00:1d.1: USB bus 1 deregistered
> [ 2.145264] uhci_hcd 0000:00:1d.1: init 0000:00:1d.1 fail, -38
> [ 2.145264] uhci_hcd: probe of 0000:00:1d.1 failed with error -38
> [ 2.167751] uhci_hcd 0000:00:1d.2: UHCI Host Controller
> [ 2.171687] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 1
> [ 2.181803] uhci_hcd 0000:00:1d.2: irq 7, io base 0x00002040
> [ 2.188158] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
> [ 2.192089] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
> [ 2.192089] usb usb1: Product: UHCI Host Controller
> [ 2.192089] usb usb1: Manufacturer: Linux 2.6.32-5-xen-686 uhci_hcd
> [ 2.192089] usb usb1: SerialNumber: 0000:00:1d.2
> [ 2.228762] usb usb1: configuration #1 chosen from 1 choice
> [ 2.235130] hub 1-0:1.0: USB hub found
> [ 2.239350] hub 1-0:1.0: 2 ports detected
> [ 2.266301] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
> [ 2.274127] sata_mv 0000:02:01.0: version 1.28
> [ 2.277900] sata_mv 0000:02:01.0: found PCI INT A -> IRQ 5
> [ 2.277900] sata_mv 0000:02:01.0: sharing IRQ 5 with 0000:02:03.0
> [ 2.277900] sata_mv 0000:02:01.0: sharing IRQ 5 with 0000:02:03.1
> [ 2.277900] sata_mv 0000:02:01.0: sharing IRQ 5 with 0000:03:02.0
> [ 2.277900] sata_mv 0000:02:01.0: sharing IRQ 5 with 0000:03:02.1
> [ 2.313432] sata_mv 0000:02:01.0: Gen-II 32 slots 8 ports SCSI mode IRQ via INTx
> [ 2.321949] ata2.00: ATAPI: CD-224E, 1.9A, max UDMA/33
> [ 2.332447] scsi3 : sata_mv
> [ 2.336027] scsi4 : sata_mv
> [ 2.339456] scsi5 : sata_mv
> [ 2.342818] ata2.00: configured for UDMA/33
> [ 2.354302] scsi6 : sata_mv
> [ 2.357747] scsi 1:0:0:0: CD-ROM TEAC CD-224E 1.9A PQ: 0 ANSI: 5
> [ 2.371535] scsi7 : sata_mv
> [ 2.382529] scsi8 : sata_mv
> [ 2.391689] scsi9 : sata_mv
> [ 2.399346] scsi10 : sata_mv
> [ 2.402872] ata3: SATA max UDMA/133 mmio m1048576@0xfc200000 port 0xfc222000 irq 5
> [ 2.406609] ata4: SATA max UDMA/133 mmio m1048576@0xfc200000 port 0xfc224000 irq 5
> [ 2.406609] ata5: SATA max UDMA/133 mmio m1048576@0xfc200000 port 0xfc226000 irq 5
> [ 2.406609] ata6: SATA max UDMA/133 mmio m1048576@0xfc200000 port 0xfc228000 irq 5
> [ 2.406609] ata7: SATA max UDMA/133 mmio m1048576@0xfc200000 port 0xfc232000 irq 5
> [ 2.406609] ata8: SATA max UDMA/133 mmio m1048576@0xfc200000 port 0xfc234000 irq 5
> [ 2.406609] ata9: SATA max UDMA/133 mmio m1048576@0xfc200000 port 0xfc236000 irq 5
> [ 2.406609] ata10: SATA max UDMA/133 mmio m1048576@0xfc200000 port 0xfc238000 irq 5
> [ 2.471695] e1000 0000:02:03.1: found PCI INT B -> IRQ 5
> [ 2.473886] e1000 0000:02:03.1: sharing IRQ 5 with 0000:02:01.0
> [ 2.473886] e1000 0000:02:03.1: sharing IRQ 5 with 0000:02:03.0
> [ 2.473886] e1000 0000:02:03.1: sharing IRQ 5 with 0000:03:02.0
> [ 2.473886] e1000 0000:02:03.1: sharing IRQ 5 with 0000:03:02.1
> [ 2.508785] sr0: scsi3-mmc drive: 24x/24x cd/rw xa/form2 cdda tray
> [ 2.512737] Uniform CD-ROM driver Revision: 3.20
> [ 2.767020] e1000: 0000:02:03.1: e1000_probe: (PCI-X:133MHz:64-bit) 00:30:48:2d:3e:d3
> [ 2.803144] e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection
> [ 3.040059] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> [ 3.060081] ata3.00: ATA-8: Hitachi HDS721010CLA332, JP4OA39C, max UDMA/133
> [ 3.064011] ata3.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
> [ 3.096102] ata3.00: configured for UDMA/133
> [ 3.101030] scsi 3:0:0:0: Direct-Access ATA Hitachi HDS72101 JP4O PQ: 0 ANSI: 5
> [ 3.584052] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> [ 3.604081] ata4.00: ATA-8: Hitachi HDS721010CLA332, JP4OA3EA, max UDMA/133
> [ 3.608010] ata4.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
> [ 3.640103] ata4.00: configured for UDMA/133
> [ 3.645002] scsi 4:0:0:0: Direct-Access ATA Hitachi HDS72101 JP4O PQ: 0 ANSI: 5
> [ 3.972054] ata5: SATA link down (SStatus 0 SControl 300)
> [ 4.296054] ata6: SATA link down (SStatus 0 SControl 300)
> [ 4.620054] ata7: SATA link down (SStatus 0 SControl 300)
> [ 4.944054] ata8: SATA link down (SStatus 0 SControl 300)
> [ 5.268054] ata9: SATA link down (SStatus 0 SControl 300)
> [ 5.592049] ata10: SATA link down (SStatus 0 SControl 300)
> [ 5.635029] sr 1:0:0:0: Attached scsi generic sg0 type 5
> [ 5.641712] scsi 3:0:0:0: Attached scsi generic sg1 type 0
> [ 5.650067] sd 3:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
> [ 5.659103] sd 4:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
> [ 5.668170] sd 4:0:0:0: Attached scsi generic sg2 type 0
> [ 5.674538] sd 4:0:0:0: [sdb] Write Protect is off
> [ 5ache: enabled, rltra320 SCSI ada 0000:03:02.1: sharing IRQ 5 with 0000:02:01.0
> [ 17.258477] aic79xx 002.408044] scsi11 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0
> [ 32.408047] <Adaptec AIC7902 Ultra320 SCSI adapter>
> [ 32.408049] aic7902: Ultra320 Wide Channel B, SCSI Id=7, PCI-X 101-133MHz, 512 SCBs
> [ 35.820011] ata3.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen
> [ 35.820011] ata3.00: failed command: READ FPDMA QUEUED
> [ 35.820011] ata3.00: cmd 60/08:00:00:00:00/00:00:00:00:00/40 tag 0 ncq 4096 in
> [ 35.820011] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 35.820011] ata3.00: status: { DRDY }
> [ 35.820011] ata3: hard resetting link
> [ 35.876030] ata4.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen
> [ 35.876030] ata4.00: failed command: READ FPDMA QUEUED
> [ 35.876030] ata4.00: cmd 60/08:00:00:00:00/00:00:00:00:00/40 tag 0 ncq 4096 in
> [ 35.876030] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 35.876030] ata4.00: status: { DRDY }
> [ 35.876030] ata4: hard resetting link
> [ 36.340053] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> [ 36.384104] ata3.00: configured for UDMA/133
> [ 36.388011] ata3.00: device reported invalid CHS sector 0
> [ 36.394842] ata3: EH complete
> [ 36.398238] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> [ 36.444106] ata4.00: configured for UDMA/133
> [ 36.448011] ata4.00: device reported invalid CHS sector 0
> [ 36.454822] ata4: EH complete
> [ 38.816054] scsi 2:0:0:0: Attempting to queue an ABORT message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
> [ 38.820011] scsi 2:0:0:0: Command already completed
> [ 48.832048] scsi 2:0:0:0: Attempting0x12 0x0 0x0 0x0 Command already completed
> [ 53.860036] scsi2: Device reset timer expired (active 1)
> [ 53.864010] scsi2: Device reset returning 0x2003
> [ 53.864010] Recovery SCB completes
> [ 63.832044] scsi 11:0:0:0: Attempting to queue an ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
> [ 63.836010] scsi 11:0:0:0: Command already completed
> [ 63.836010] scsi 11:0:0:0: Attempting to queue a TARGET RESET message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
> [ 63.836010] scsi11: Device reset code sleeping
> [ 66.820009] ata3.00: NCQ disabled due to excessive errors
> [ 66.820009] ata3.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen
> [ 66.820009] ata3.00: failed command: READ FPDMA QUEUED
> [ 66.820009] ata3.00: cmd 60/08:00:00:00:00/00:00:00:00:00/40 tag 0 ncq 4096 in
> [ 66.820009] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 66.820009] ata3.00: status: { DRDY }
> [ 66.820009] ata3: hard resetting link
> [ 66.881899] ata4.00: NCQ disabled due to excessive errors
> [ 66.881899] ata4.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen
> [ 66.881899] ata4.00: failed command: READ FPDMA QUEUED
> [ 66.881899] ata4.00: cmd 60/08:00:00:00:00/00:00:00:00:00/40 tag 0 ncq 4096 in
> [ 66.881899] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 66.881899] ata4.00: status: { DRDY }
> [ 66.881899] ata4: hard resetting link
> [ 67.344052] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> [ 67.388105] ata3.00: configured for UDMA/133
> [ 67.392010] ata3.00: device reported invalid CHS sector 0
> [ 67.398791] ata3: EH complete
> [ 67.408053] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> [ 67.452101] ata4.00: configured for UDMA/133
> [ 67.456010] ata4.00: device reported invalid CHS sector 0
> [ 67.462824] ata4: EH complete
> [ 68.864038] scsi11: Device reset timer expired (active 1)
> [ 68.868010] scsi11: Device reset returning 0x2003
> [ 68.868010] Recovery SCB completes
> [ 73.864031] scsi 2:0:0:0: Attempting to queue an ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
> [ 73.868010] scsi 2:0:0:0: Command already completed
> [ 73.868010] scsi 2:0:0:0: Device offlined - not ready after error recovery
> [ 88.868038] scsi 11:0:0:0: Attempting to queue an ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
> [ 88.872011] scsi 11:0:0:0: Command already completed
> [ 88.872011] scsi 11:0:0:0: Device offlined - not ready after error recovery
> [ 94.816051] scsi 2:0:1:0: Attempting to queue an ABORT message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
> [ 94.820010] scsi 2:0:1:0: Command already completed
> [ 97.820010] ata3: limiting SATA link speed to 1.5 Gbps
> [ 97.820010] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
> [ 97.820010] ata3.00: failed command: READ DMA
> [ 97.820010] ata3.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
> [ 97.820010] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 97.820010] ata3.00: status: { DRDY }
> [ 97.820010] ata3: hard resetting link
> [ 97.880736] ata4: limiting SATA link speed to 1.5 Gbps
> [ 97.880736] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
> [ 97.880736] ata4.00: failed command: READ DMA
> [ 97.880736] ata4.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
> [ 97.880736] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 97.880736] ata4.00: status: { DRDY }
> [ 97.880736] ata4: hard resetting link
> [ 98.344052] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
> [ 98.388101] ata3.00: configured for UDMA/133
> [ 98.392010] ata3.00: device reported invalid CHS sector 0
> [ 98.398778] ata3: EH complete
> [ 98.404055] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
> [ 98.448105] ata4.00: configured for UDMA/133
> [ 98.452010] ata4.00: device reported invalid CHS sector 0
> [ 98.458821] ata4: EH complete
> [ 104.832048] scsi 2:0:1:0: Attempting to queue an ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
> [ 104.836009] scsi 2:0:1:0: Command already completed
> [ 104.836009] scsi 2:0:1:0: Attempting to queue a TARGET RESET message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
> [ 104.836009] scsi2: Device reset code sleeping
> [ 109.816050] scsi 11:0:1:0: Attempting to queue an ABORT message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
> [ 109.820009] scsi 11:0:1:0: Command already completed
> [ 109.864037] scsi2: Device reset timer expired (active 1)
> [ 109.868009] scsi2: Device reset returning 0x2003
> [ 109.868009] Recovery SCB completes
> [ 119.832030] scsi 11:0:1:0: Attempting to queue an ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
> [ 119.836010] scsi 11:0:1:0: Command already completed
> [ 119.836010] scsi 11:0:1:0: Attempting to queue a TARGET RESET message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
> [ 119.836010] scsi11: Device reset code sleeping
> [ 124.864037] scsi11: Device reset timer expired (active 1)
> [ 124.868010] scsi11: Device reset returning 0x2003
> [ 124.868010] Recovery SCB completes
> [ 128.820009] ata3.00: limiting speed to UDMA/100:PIO4
> [ 128.820009] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
> [ 128.820009] ata3.00: failed command: READ DMA
> [ 128.820009] ata3.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
> [ 128.820009] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 128.820009] ata3.00: status: { DRDY }
> [ 128.820009] ata3: hard resetting link
> [ 128.880543] ata4.00: limiting speed to UDMA/100:PIO4
> [ 128.880543] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
> [ 128.880543] ata4.00: failed command: READ DMA
> [ 128.880543] ata4.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
> [ 128.880543] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 128.880543] ata4.00: status: { DRDY }
> [ 128.880543] ata4: hard resetting link
> [ 129.344052] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
> [ 129.388100] ata3.00: configured for UDMA/100
> [ 129.392009] ata3.00: device reported invalid CHS sector 0
> [ 129.398821] ata3: EH complete
> [ 129.412059] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
> [ 129.456102] ata4.00: configured for UDMA/100
> [ 129.460010] ata4.00: device reported invalid CHS sector 0
> [ 129.466822] ata4: EH complete
> [ 129.868035] scsi 2:0:1:0: Attempting to queue an ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
> [ 129.872009] scsi 2:0:1:0: Command already completed
> [ 129.872009] scsi 2:0:1:0: Device offlined - not ready after error recovery
> [ 144.868037] scsi 11:0:1:0: Attempting to queue an ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
> [ 144.872010] scsi 11:0:1:0: Command already completed
> [ 144.872010] scsi 11:0:1:0: Device offlined - not ready after error recovery
> [ 150.816048] scsi 2:0:2:0: Attempting to queue an ABORT message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
> [ 150.820010] scsi 2:0:2:0: Command already completed
> [ 159.820009] ata3.00: limiting speed to UDMA/33:PIO4
> [ 159.82 dma 4096 in
> [ 1limiting speed t0:00/00:00:00:00nk
> [ 160.404059] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
> [ 160.410953] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
> [ 160.448373] ata4.00: configured for UDMA/33
> [ 160.452010] ata4.00: device reported invalid CHS sector 0
> [ 160.459004] ata4: EH complete
> [ 160.468105] ata3.00: configured for UDMA/33
> [ 160.472010] ata3.00: device reported invalid CHS sector 0
> [ 160.478695] ata3: EH complete
> [ 160.832049] scsi 2:0:2:0: Attempting to queue an ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
> [ 160.836010] scsi 2:0:2:0: Command already completed
> [ 160.836010] scsi 2:0:2:0: Attempting to queue a TARGET RESET message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
> [ 160.836010] scsi2: Device reset code sleeping
> [ 165.816040] scsi 11:0:2:0: Attempting to queue an ABORT message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
> [ 165.820009] scsi 11:0:2:0: Command already completed
> [ 165.864038] scsi2: Device reset timer expired (active 1)
> [ 165.868010] scsi2: Device reset returning 0x2003
> [ 165.868010] Recovery SCB completes
> [ 175.832049] scsi 11:0:2:0: Attempting to queue an ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
> [ 175.836010] scsi 11:0:2:0: Command already completed
> [ 175.836010] scsi 11:0:2:0: Attempting to queue a TARGET RESET message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
> [ 175.836010] scsi11: Device reset code sleeping
> [ 180.864037] scsi11: Device reset timer expired (active 1)
> [ 180.868010] scsi11: Device reset returning 0x2003
> [ 180.868010] Recovery SCB completes
>
> udevadm settle - timeout of 180 seconds reached, the event queue contains:
> /sys/devices/pci0000.0/0000:02:01.0/h.0/0000:01:1d.0/0000:02:01.0/host3/target3:0:0/3:0:0:0/bsg/3:0:0:0 (541)
> /sys/devices/pci0000:00/0000:00:02.0/0000:01:1d.0/0000:02:01.0/host3/target3:0:0/3:0:0:0/scsi_generic/sg1 (550)
> /sys/devices/pci0000:00/0000:00:02.0/0000:01:1d.0/0000:02:01.0/host3/target3:0:0/3:0:0:0/scsi_disk/3:0:0:0 (554)
> /sys/devices/pci0000:00/0000:00:02.0/0000:01:1f.0/0000:03:02.1/host11 (560)
> /sys/devices/pci0000:00/0000:00:02.0/0000:01:1f.0/0000:03:02.1/host11/scsi_host/host11 (561)
> /sys/devices/pci0000:00/0000:00:02.0/0000:01:1f.0/0000:03:02.1/host11/spi_host/host11 (562)
> udevd[48]: worker [57] unexpectedly returned with status 0x0100
>
> udevd[48]: worker [57] failed while handling '/devices/pci0000:00/0000:00:02.0/0000:01:1f.0/0000:03:02.1'
>
> udevd[48]: worker [58] unexpectedly returned with status 0x0100
>
> udevd[48]: worker [58] failed while handling '/devices/pci0000:00/0000:00:1f.1/host1/target1:0:0/1:0:0:0/scsi_device/1:0:0:0'
>
> udevd[48]: worker [51] unexpectedly returned with status 0x0100
>
> udevd[48]: worker [51] failed while handling '/devices/pci0000:00/0000:00:02.0/0000:01:1d.0/0000:02:01.0/host3/target3:0:0/3:0:0:0'
>
> [ 185.868036] scsi 2:0:2:0: Attempting to queue an ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
> [ 185.872011] scsi 2:0:2:0: Command already completed
> [ 185.872011] scsi 2:0:2:0: Device offlined - not ready after error recovery
> [ 190.820010] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
> [ 190.820010] ata4.00: failed command: READ DMA
> [ 190.820010] ata4.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
> [ 190.820010] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 190.820010] ata4.00: status: { DRDY }
> [ 190.820010] ata4: hard resetting link
> [ 190.876250] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
> [ 190.876250] ata3.00: failed command: READ DMA
> [ 190.876250] ata3.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
> [ 190.876250] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 190.876250] ata3.00: status: { DRDY }
> [ 190.876250] ata3: hard resetting link
> [ 191.392055] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
> [ 191.399001] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
> [ 191.436366] ata3.00: configured for UDMA/33
> [ 191.440010] ata3.00: device reported invalid CHS sector 0
> [ 191.440010] sd 3:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
> [ 191.440010] sd 3:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
> [ 191.440010] Descriptor sense data with sense descriptors (in hex):
> [ 191.440010] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
> [ 191.440010] 00 00 00 00
> [ 191.440010] sd 3:0:0:0: [sda] Add. Sense: No additional sense information
> [ 191.440010] sd 3:0:0:0: [sda] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00
> [ 191.440010] end_request: I/O error, dev sda, sector 0
> [ 191.440010] Buffer I/O error on device sda, logical block 0
> [ 191.440010] ata3: EH complete
> [ 191.520102] ata4.00: configured for UDMA/33
> [ 191.524011] ata4.00: device reported invalid CHS sector 0
> [ 191.524011] sd 4:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
> [ 191.524011] sd 4:0:0:0: [sdb] Sense Key : Aborted Command [current] [descriptor]
> [ 191.524011] Descriptor sense data with sense descriptors (in hex):
> [ 191.524011] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
> [ 191.524011] 00 00 00 00
> [ 191.524011] sd 4:0:0:0: [sdb] Add. Sense: No additional sense information
> [ 191.524011] sd 4:0:0:0: [sdb] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00
> [ 191.524011] end_request: I/O error, dev sdb, sector 0
> [ 191.524011] Buffer I/O error on device sdb, logical block 0
> [ 191.524011] ata4: EH complete
> [ 200.924033] scsi 11:0:2:0: Attempting to queue an ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
> [ 200.928009] scsi 11:0:2:0: Command already completed
> [ 200.928009] scsi 11:0:2:0: Device offlined - not ready after error recovery
> [ 206.816034] scsi 2:0:3:0: Attempting to queue an ABORT message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
> [ 206.820009] scsi 2:0:3:0: Command already completed
> [ 216.832030] scsi 2:0:3:0: Attempting to queue an ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
> [ 216.836009] scsi 2:0:3:0: Command already completed
> [ 216.836009] scsi 2:0:3:0: Attempting to queue a TARGET RESET message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
> [ 216.836009] scsi2: Device reset code sleeping
> [ 221.820010] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
> [ 221.820010] ata3.00: failed command: READ DMA
> [ 221.820010] ata3.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
> [ 221.820010] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 221.820010] ata3.00: status: { DRDY }
> [ 221.820010] ata3: hard resetting link
> [ 221.870863] scsi 11:0:3:0: Attempting to queue an ABORT message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
> [ 221.874840] scsi 11:0:3:0: Command already completed
> [ 221.887981] scsi2: Device reset timer expired (active 1)
> [ 221.891952] scsi2: Device reset returning 0x2003
> [ 221.891952] Recovery SCB completes
> [ 221.914105] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
> [ 221.914105] ata4.00: failed command: READ DMA
> [ 221.914105] ata4.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
> [ 221.914105] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 221.914105] ata4.00: status: { DRDY }
> [ 221.914105] ata4: hard resetting link
> [ 222.376054] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
> [ 222.420098] ata3.00: configured for UDMA/33
> [ 222.424010] ata3.00: device reported invalid CHS sector 0
> [ 222.430739] ata3: EH complete
> [ 222.434122] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
> [ 222.480098] ata4.00: configured for UDMA/33
> [ 222.484010] ata4.00: device reported invalid CHS sector 0
> [ 222.490631] ata4: EH complete
> [ 231.884033] scsi 11:0:3:0: Attempting to queue an ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
> [ 231.888010] scsi 11:0:3:0: Command already completed
> [ 231.888010] scsi 11:0:3:0: Attempting to queue a TARGET RESET message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
> [ 231.888010] scsi11: Device reset code sleeping
> [ 236.916031] scsi11: Device reset timer expired (active 1)
> [ 236.920010] scsi11: Device reset returning 0x2003
> [ 236.920010] Recovery SCB completes
> [ 240.384044] INFO: task modprobe:91 blocked for more than 120 seconds.
> [ 240.388009] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
> [ 240.388009] modprobe D df550168 0 91 1 0x00000000
> [ 240.388009] c2b36ec0 00000286 c10ca12b df550168 c10fbea8 c145ee20 c145ee20 c10fbbbf
> [ 240.388009] c2b3707c c32b8e20 00000000 8d12580e 00000007 c1005fb4 0000000b 00000000
> [ 240.388009] c14a02e4 c2b3707c c14a02e4 00008b8b c14a02e4 c10066d3 c128e2f9 00000000
> [ 240.388009] Call Trace:
> [ 240.388009] [<c10ca12b>] ? iput+0x21/0x4a
> [ 240.388009] [<c10fbea8>] ? sysfs_addrm_finish+0x46/0x199
> [ 240.388009] [<c10fbbbf>] ? sysfs_add_one+0x11/0xb8
> [ 240.388009] [<c1005fb4>] ? xen_force_evtchn_callback+0xc/0x10
> [ 240.388009] 0.388009] [<c1041008efc>] ? sysca88009] ata_aux 00
> [ 240.388009]0 c2a6c5fc df804600 df4027b8 c3312764 c10ca2d3 00000002 df402678
> [ 240.388009] Call Trace:
> [ 240.388009] [<c10ca2d3>] ? wait_on_inode+0x21/0x24
> [ 240.388009] [<c128d8ef>] ? __mutex_lock_common+0xe8/0x13b
> [ 240.388009] [<c128d951>] ? __mutex_lock_slowpath+0xf/0x11
> [ 240.388009] [<c128d9e2>] ? mutex_lock+0x17/0x24
> [ 240.388009] [<c128d9e2>] ? mutex_lock+0x17/0x24
> [ 240.388009] [<c10da461>] ? revalidate_disk+0x34/0x53
> [ 240.388009] [<e0962a9c>] ? sd_rescan+0x17/0x1e [sd_mod]
> [ 240.388009] [<e083f8cf>] ? scsi_rescan_device+0x7f/0x94 [scsi_mod]
> [ 240.388009] [<e08de42f>] ? ata_scsi_dev_rescan+0x50/0x94 [libata]
> [ 240.388009] [<c10483b3>] ? worker_thread+0x141/0x1bd
> [ 240.388009] [<e08de3df>] ? ata_scsi_dev_rescan+0x0/0x94 [libata]
> [ 240.388009] [<c104b0ea>] ? autoremove_wake_function+0x0/0x2d
> [ 240.388009] [<c1048272>] ? worker_thread+0x0/0x1bd
> [ 240.388009] [<c104aeb8>] ? kthread+0x61/0x66
> [ 240.388009] [<c104ae57>] ? kthread+0x0/0x66
> [ 240.388009] [<c1009a67>] ? kernel_thread_helper+0x7/0x10
> [ 240.388009] INFO: task modprobe:119 blocked for more than 120 seconds.
> [ 240.388009] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
> [ 240.388009] modprobe D 40c124f6 0 119 1 0x00000000
> [ 240.388009] df886640 00000286 00000000 40c124f6 00000000 c145ee20 c145ee20 c246a6c0
> [ 240.388009] df8867fc c32b8e20 00000000 52140a60 00000001 e09664be 00000000 c10846e8
> [ 240.388009] c128d9d6 df8867fc c128e201 c1290834 013d4850 c13d3ef8 c128e2f9 00000000
> [ 240.388009] Call Trace:
> [ 240.388009] [<c10846e8>] ? trace_module_notify+0x394/0x39e
> [ 009] [<c128e2f9>009] [<c104fedf>] ? async_synchronize_full+0x10/0x29
> [ 240.388009] [<c105e98d>] ? sys_init_module+0x15b/0x1d7
> [ 240.388009] [<c1008efc>] ? syscall_call+0x7/0xb
> [ 240.388009] INFO: task modprobe:123 blocked for more than 120 seconds.
> [ 240.388009] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
> [ 240.388009] modprobe D fffffffe 0 123 1 0x00000000
> [ 240.388009] c24d4440 00000286 dde02510 fffffffe c10fbbbf c145ee20 c145ee20 c2b4d9c0
> [ 240.388009] c24d45fc c32b8e20 00000000 51d9293e 00000001 c1005fb4 0000000b 00000000
> [ 240.388009] c14a02e4 c24d45fc c14a02e4 00008787 c14a02e4 c10066d3 c128e2f9 00000000
> [ 240.388009] Call Trace:
> [ 240.388009] [<c10fbbbf>] ? sysfs_add_one+0x11/0xb8
> [ 240.388009] [<c1005fb4>] ? xen_force_evtchn_callback+0xc/0x10
> [ 240.388009] [<c10066d3>] ? xen_restore_fl_direct_end+0x0/0x1
> [ 240.388009] [<c128e2f9>] ? _spin_unlock_irqrestore+0xd/0xf
> [ 240.388009] [<c104fe6f>] ? async_synchronize_cookie_domain+0xbb/0x111
> [ 240.388009] [<c104b0ea>] ? autoremove_wake_function+0x0/0x2d
> [ 240.388009] [<c104fedf>] ? async_synchronize_full+0x10/0x29
> [ 240.388009] [<c105e98d>] ? sys_init_module+0x15b/0x1d7
> [ 240.388009] [<c1008efc>] ? syscall_call+0x7/0xb
> [ 241.916030] scsi 2:0:3:0: Attempting to queue an ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
> [ 241.920010] scsi 2:0:3:0: Command already completed
> [ 241.920010] scsi 2:0:3:0: Device offlined - not ready after error recovery
> [ 252.820009] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
> [ 252.820009] ata3.00: failed command: READ DMA
> [ 252.820009] ata3.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
> [ 252.820009] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 252.820009] ata3.00: status: { DRDY }
> [ 252.820009] ata3: hard resetting link
> [ 252.874950] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
> [ 252.874950] ata4.00: failed command: READ DMA
> [ 252.874950] ata4.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
> [ 252.874950] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 252.874950] ata4.00: status: { DRDY }
> [ 252.874950] ata4: hard resetting link
> [ 253.336053] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
> [ 253.380099] ata3.00: configured for UDMA/33
> [ 253.384010] ata3.00: device reported invalid CHS sector 0
> [ 253.390633] ata3: EH complete
> [ 253.394008] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
> [ 253.440099] ata4.00: configured for UDMA/33
> [ 253.444010] ata4.00: device reported invalid CHS sector 0
> [ 253.450742] ata4: EH complete
> [ 256.920033] scsi 11:0:3:0: Attempting to queue an ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
> [ 256.924010] scsi 11:0:3:0: Command already completed
> [ 256.924010] scsi 11:0:3:0: Device offlined - not ready after error recovery
> [ 262.816035] scsi 2:0:4:0: Attempting to queue an ABORT message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
> [ 262.820010] scsi 2:0:4:0: Command already completed
> [ 272.832039] scsi 2:0:4:0: Attempting to queue an ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
> [ 272.836010] scsi 2:0:4:0: Command already completed
> [ 272.836010] scsi 2:0:4:0: Attempting to queue a TARGET RESET message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
> [ 272.836010] scsi2: Device reset code sleeping
> [ 277.816036] scsi 11:0:4:0: Attempting to queue an ABORT message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
> [ 277.820010] scsi 11:0:4:0: Command already completed
> [ 277.864031] scsi2: Device reset timer expired (active 1)
> [ 277.868010] scsi2: Device reset returning 0x2003
> [ 277.868010] Recovery SCB completes
> [ 283.820010] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
> [ 283.820010] ata3.00: failed command: READ DMA
> [ 283.820010] ata3.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
> [ 283.820010] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 283.820010] ata3.00: status: { DRDY }
> [ 283.820010] ata3: hard resetting link
> [ 283.874696] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
> [ 283.874696] ata4.00: failed command: READ DMA
> [ 283.874696] ata4.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
> [ 283.874696] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 283.874696] ata4.00: status: { DRDY }
> [ 283.874696] ata4: hard resetting link
> [ 284.392054] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
> [ 284.398986] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
> [ 284.436366] ata4.00: configured for UDMA/33
> [ 284.440010] ata4.00: device reported invalid CHS sector 0
> [ 284.446876] ata4: EH complete
> [ 284.456100] ata3.00: configured for UDMA/33
> [ 284.460011] ata3.00: device reported invalid CHS sector 0
> [ 284.466689] ata3: EH complete
> [ 287.832030] scsi 11:0:4:0: Attempting to queue an ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
> [ 287.836009] scsi 11:0:4:0: Command already completed
> [ 287.836009] scsi 11:0:4:0: Attempting to queue a TARGET RESET message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
> [ 287.836009] scsi11: Device reset code sleeping
> [ 292.864039] scsi11: Device reset timer expired (active 1)
> [ 292.868009] scsi11: Device reset returning 0x2003
> [ 292.868009] Recovery SCB completes
> [ 297.868034] scsi 2:0:4:0: Attempting to queue an ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
> [ 297.872010] scsi 2:0:4:0: Command already completed
> [ 297.872010] scsi 2:0:4:0: Device offlined - not ready after error recovery
> [ 312.868030] scsi 11:0:4:0: Attempting to queue an ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
> [ 312.872010] scsi 11:0:4:0: Command already completed
> [ 312.872010] scsi 11:0:4:0: Device offlined - not ready after error recovery
> [ 315.004010] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
> [ 315.004010] ata4.00: failed command: READ DMA
> [ 315.004010] ata4.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
> [ 315.004010] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 315.004010] ata4.00: status: { DRDY }
> [ 315.004010] ata4: hard resetting link
> [ 315.058967] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
> [ 315.058967] ata3.00: failed command: READ DMA
> [ 315.058967] ata3.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
> [ 315.058967] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 315.058967] ata3.00: status: { DRDY }
> [ 315.058967] ata3: hard resetting link
> [ 315.520051] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
> [ 315.564098] ata4.00: configured for UDMA/33
> [ 315.568010] ata4.00: device reported invalid CHS.608006] ata3.00 320.576032] atlid CHS sector 028.412010] scsi 2:0:5:0: Attempting to queue a TARGET RESET message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
> [ 328.412010] scsi2: Device reset code sleeping
> [ 333.436030] scsi2: Device reset timer expired (active 1)
> [ 333.440009] scsi2: Device reset returning 0x2003
> [ 333.440009] Recovery SCB completes
> [ 334.000043] scsi 11:0:5:0: Attempting to queue an ABORT message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
> [ 334.004010] scsi 11:0:5:0: Command already completed
> [ 344.016029] scsi 11:0:5:0: Attempting to queue an ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
> [ 344.020009] scsi 11:0:5:0: Command already completed
> [ 344.020009] scsi 11:0:5:0: Attempting to queue a TARGET RESET message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
> [ 344.020009] scsi11: Device reset code sleeping
> [ 346.004010] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
> [ 346.004010] ata4.00: failed command: READ DMA
> [ 346.004010] ata4.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
> [ 346.004010] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> [ 346.004010] ata4.00: status: { DRDY }
> [ 346.004010] ata4: hard resetting link
> [ 346.528052] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
> [ 346.572097] ata4.00: configured for UDMA/33
> [ 346.576011] ata4.00: device reported invalid CHS sector 0
> [ 346.582652] ata4: EH complete
> [ 349.048030] scsi11: Device reset timer expired (active 1)
> [ 349.052009] scsi11: Device reset returning 0x2003
> [ 349.052009] Recovery SCB completes
> [ 352.004010] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
> [ 352.004010] ata3.00: failed command: READ DMA
> [ 352.004010] ata3.00: cmd c8/00:08:00:00:00/00:00:00:g link
> [ 352.528ta3: EH complete
> [ 353.440031] scsi 2:0:5:0: Attempting to queue an ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
> [ 353.444010] scsi 2:0:5:0: Command already completed
> [ 353.444010] scsi 2:0:5:0: Device offlined - not ready after error recovery
> [ 360.384039] INFO: task modprobe:91 blocked for more than 120 seconds.
> [ 360.388010] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
> [ 360.388010] modprobe D df550168 0 91 1 0x00000000
> [ 360.388010] c2b36ec0 00000286 c10ca12b df550168 c10fbea8 c145ee20 c145ee20 c10fbbbf
> [ 360.388010] c2b3707c c32b8e20 00000000 8d12580e 00000007 c1005fb4 0000000b 00000000
> [ 360.388010] c14a02e4 c2b3707c c14a02e4 00008b8b c14a02e4 c10066d3 c128e2f9 00000000
> [ 360.388010] Call Trace:
> [ 360.388010] [<c10ca12b>] ? iput+0x21/0x4a
> [ 360.388010] [<c10fbea8>] ? sysfs_addrm_finish+0x46/0x199
> [ 360.388010] [<c10fbbbf>] ? sysfs_add_one+0x11/0xb8
> [ 360.388010] [<c1005fb4>] ? xen_force_evtchn_callback+0xc/0x10
> [ 360.388010] [<c10066d3>] ? xen_restore_fl_direct_end+0x0/0x1
> [ 360.388010] [<c128e2f9>] ? _spin_unlock_irqrestore+0xd/0xf
> [ 360.388010] [<c104fe6f>] ? async_synchronize_cookie_domain+0xbb/0x111
> [ 360.388010] [<c104b0ea>] ? autoremove_wake_function+0x0/0x2d
> [ 360.388010] [<c104fedf>] ? async_synchronize_full+0x10/0x29
> [ 360.388010] [<c105e98d>] ? sys_init_module+0x15b/0x1d7
> [ 360.388010] [<c1008efc>] ? syscall_call+0x7/0xb
> [ 360.388010] INFO: task ata_aux:95 blocked for more than 120 seconds.
> [ 360.388010] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
> [ 360.388010] ata_aux D c24abefc 0 95 2 0x00000000
> [ 360.388010] c2a6c440 00000246 00000005 c24abefc 00000000 c145ee20 c145ee20 00000000
> [ 360.388010] c2a6c5fc c32b8e20 00000000 79f0e2cb 00000008 00000000 00000000 c2b5d800
> [ 360.388010] 00000200 c2a6c5fc df804600 df4027b8 c3312764 c10ca2d3 00000002 df402678
> [ 360.388010] Call Trace:
> [ 360.388010] [<c10ca2d3>] ? wait_on_inode+0x21/0x24
> [ 360.388010] [<c128d8ef>] ? __mutex_lock_common+0xe8/0x13b
> [ 360.388010] [<c128d951>] ? __mutex_lock_slowpath+0xf/0x11
> [ 360.388010] [<c128d9e2>] ? mutex_lock+0x17/0x24
> [ 360.388010] [<c128d9e2>] ? mutex_lock+0x17/0x24
> [ 360.388010] [<c10da461>] ? revalidate_disk+0x34/0x53
> [ 360.388010] [<e0962a9c>] ? sd_rescan+0x17/0x1e [sd_mod]
> [ 360.388010] [<e083f8cf>] ? scsi_rescan_device+0x7f/0x94 [scsi_mod]
> [ 360.388010] [<e08de42f>] ? ata_scsi_dev_rescan+0x50/0x94 [libata]
> [ 360.388010] [<c10483b3>] ? worker_thread+0x141/0x1bd
> [ 360.388010] [<e08de3df>] ? ata_scsi_dev_rescan+0x0/0x94 [libata]
> [ 360.388010] [<c104b0ea>] ? autoremove_wake_function+0x0/0x2d
> [ 360.388010] [<c1048272>] ? worker_thread+0x0/0x1bd
> [ 360.388010] [<c104aeb8>] ? kthread+0x61/0x66
> [ 360.388010] [<c104ae57>] ? kthread+0x0/0x66
> [ 360.388010] [<c1009a67>] ? kernel_thread_helper+0x7/0x10
> [ 360.388010] INFO: task async/6:116 blocked for more than 120 seconds.
> [ 360.388010] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
> [ 360.388010] async/6 D b219ec32 0 116 2 0x00000000
> [ 360.388010] c2b35980 00000246 0000002e b219ec32 0000002e c145ee20 c145ee20 c145a354
> [ 360.388010] c2b35b3c c32b8e20 00000000 0000002e ae79d2c2 00000094 00000184 c13f9d80
> [ 360.388010] 19d8b41a c2b35b3c ffff971d 00000000 19d8b41a 00000000 c2b70918 000061e2
> [ 360.388010] Call Trace:
> [ 360.388010] [<c128d242>] ? io_schedule+0x5f/0x98
> [ 360.388010] [<c108e911>] ? sync_page+0x3a/0x3d
> [ 360.388010] [<c128d6c9>] ? __wait_on_bit+0x33/0x58
> [ 360.388010] [<c108e8d7>] ? sync_page+0x0/0x3d
> [ 360.388010] [<c108eae2>] ? wait_on_page_bit+0x7f/0x88
> [ 360.388010] [<c104b117>] ? wake_bit_function+0x0/0x3c
> [ 360.388010] [<c108eb01>] ? wait_on_page_read+0x16/0x2d
> [ 360.388010] [<c10f5c14>] ? read_dev_sector+0x26/0x60
> [ 360.388010] [<c10f6880>] ? adfspart_check_ICS+0x20/0x14c
> [ 360.388010] [<c128c8a4>] ? printk+0xe/0x12
> [ 360.388010] [<c10f6650>] ? rescan_partitions+0x17e/0x378
> [ 360.388010] [<c10f6860>] ? adfspart_check_ICS+0x0/0x14c
> [ 360.388010] [<c113ebe4>] ? kobject_get+0xf/0x13
> [ 360.388010] [<c10dac1b>] ? __blkdev_get+0x225/0x2c7
> [ 360.388010] [<c10f5cfe>] ? register_disk+0xb0/0xfd
> [ 360.388010] [<c1136a6f>] ? add_disk+0x9a/0xe8
> [ 360.388010] [<c1136231>] ? exact_match+0x0/0x4
> [ 360.388010] [<c11365e2>] ? exact_lock+0x0/0xd
> [ 360.388010] [<e0964fb2>] ? sd_probe_async+0xfc/0x18d [sd_mod]
> [ 360.388010] [<c104fcc1>] ? async_thread+0xe5/0x1d8
> [ 360.388010] [<c10341cb>] ? default_wake_function+0x0/0x8
> [ 360.388010] [<c104fbdc>] ? async_thread+0x0/0x1d8
> [ 360.388010] [<c104aeb8>] ? kthread+0x61/0x66
> [ 360.388010] [<c104ae57>] ? kthread+0x0/0x66
> [ 360.388010] [<c1009a67>] ? kernel_thread_helper+0x7/0x10
> [ 360.388010] INFO: task async/7:117 blocked for more than 120 seconds.
> [ 360.388010] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
> [ 360.388010] async/7 D ad1e94b0 0 117 2 0x00000000
> [ 360.388010] c2b34cc0 00000246 0000002e ad1e94b0 0000002e c145ee20 c145ee20 c145a354
> [ 360.388010] c2b34e7c c32b8e20 00000000 0000002e ae79d2c2 00000094 00000184 c13f9d80
> [ 360.388010] 14dd5c98 c2b34e7c ffff9708 00000000 14dd5c98 00000000 c2b70968 000061de
> [ 360.388010] Call Trace:
> [ 360.388010] [<c128d242>] ? io_schedule+0x5f/0x98
> [ 360.388010] [<c108e911>] ? sync_page+0x3a/0x3d
> [ 360.388010] [<c128d6c9>] ? __wait_on_bit+0x33/0x58
> [ 360.388010] [<c108e8d7>] ? sync_page+0x0/0x3d
> [ 360.388010] [<c108eae2>] ? wait_on_page_bit+0x7f/0x88
> [ 360.388010] [<c104b117>] ? wake_bit_function+0x0/0x3c
> [ 360.388010] [<c108eb01>] ? wait_on_page_read+0x16/0x2d
> [ 360.388010] [<c10f5c14>] ? read_dev_sector+0x26/0x60
> [ 360.388010] [<c10f6880>] ? adfspart_check_ICS+0x20/0x14c
> [ 360.388010] [<c128c8a4>] ? printk+0xe/0x12
> [ 360.388010] [<c10f6650>] ? rescan_partitions+0x17e/0x378
> [ 360.388010] [<c10f6860>] ? adfspart_check_ICS+0x0/0x14c
> [ 360.388010] [<c113ebe4>] ? kobject_get+0xf/0x13
> [ 360.388010] [<c10dac1b>] ? __blkdev_get+0x225/0x2c7
> [ 360.388010] [<c10f5cfe>] ? register_disk+0xb0/0xfd
> [ 360.388010] [<c1136a6f>] ? add_disk+0x9a/0xe8
> [ 360.388010] [<c1136231>] ? exact_match+0x0/0x4
> [ 360.388010] [<c11365e2>] ? exact_lock+0x0/0xd
> [ 360.388010] [<e0964fb2>] ? sd_probe_async+0xfc/0x18d [sd_mod]
> [ 360.388010] [<c104fcc1>] ? async_thread+0xe5/0x1d8
> [ 360.388010] [<c10341cb>] ? default_wake_function+0x0/0x8
> [ 360.388010] [<c104fbdc>] ? async_thread+0x0/0x1d8
> [ 360.388010] [<c104aeb8>] ? kthread+0x61/0x66
> [ 360.388010] [<c104ae57>] ? kthread+0x0/0x66
> [ 360.388010] [<c1009a67>] ? kernel_thread_helper+0x7/0x10
> [ 360.388010] INFO: task modprobe:119 blocked for more than 120 seconds.
> [ 360.388010] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
> [ 360.388010] modprobe D 40c124f6 0 119 1 0x00000000
> [ 360.388010] df886640 00000286 00000000 40c124f6 00000000 c145ee20 c145ee20 c246a6c0
> [ 360.388010] df8867fc c32b8e20 00000000 52140a60 00000001 e09664be 00000000 c10846e8
> [ 360.388010] c128d9d6 df8867fc c128e201 c1290834 013d4850 c13d3ef8 c128e2f9 00000000
> [ 360.388010] Call Trace:
> [ 360.388010] [<c10846e_module_callback+ve_wake_function
> [ 360.388010] In 120 seconds.
> [000286 dde02510 fffffffe c10fbbbf c145ee20 c145ee20 c2b4d9c0
> [ 360.388010] c24d45fc c32b8e20 00000000 51d9293e 00000001 c1005fb4 0000000b 00000000
> [ 360.388010] c14a02e4 c24d45fc c14a02e4 00008787 c14a02e4 c10066d3 c128e2f9 00000000
> [ 360.388010] Call Trace:
> [ 360.388010] [<c10fbbbf>] ? sysfs_add_one+0x11/0xb8
> [ 360.388010] [<c1005fb4>] ? xen_force_evtchn_callback+0xc/0x10
> [ 360.388010] [<c10066d3>] ? xen_restore_fl_direct_end+0x0/0x1
> [ 360.388010] [<c128e2f9>] ? _spin_unlock_irqrestore+0xd/0xf
> [ 360.388010] [<c104fe6f>] ? async_synchronize_cookie_domain+0xbb/0x111
> [ 360.388010] [<c104b0ea>] ? autoremove_wake_function+0x0/0x2d
> [ 360.388010] [<c104fedf>] ? async_synchronize_full+0x10/0x29
> [ 360.388010] [<c105e98d>] ? sys_init_module+0x15b/0x1d7
> [ 360.388010] [<c1008efc>] ? syscall_call+0x7/0xb
> [ 369.052030] scsi 11:0:5:0: Attempting to queue an ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
> [ 369.056010] scsi 11:0:5:0: Command already completed
> [ 369.056010] scsi 11:0:5:0: Device offlined - not ready after error recovery
> [ 374.000036] scsi 2:0:6:0: Attempting to queue an ABORT message:CDB: 0x12 0x0 0x0 0x0 0x24 0x0
> [ 374.004010] scsi 2:0:6:0: Command already completed
>
> -- Package-specific info:
> ** Version:
> Linux version 2.6.32-5-xen-686 (Debian 2.6.32-27) (maks@debian.org) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Sun Oct 31 02:38:31 UTC 2010
>
> ** Command line:
> BOOT_IMAGE=/vmlinuz-2.6.32-5-xen-686 root=/dev/mapper/quelea0-root ro console=tty0 console=ttyS0,115200n8
>
> ** Not tainted
>
> ** Kernel log:
> [ 3.073378] e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection
> [ 3.076473] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> [ 3.095287] ata4.00: ATA-8: Hitachi HDS721010CLA332, JP4OA3EA, max UDMA/133
> [ 3.102310] ata4.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
> [ 3.132507] ata4.00: configured for UDMA/133
> [ 3.137021] scsi 3:0:0:0: Direct-Access ATA Hitachi HDS72101 JP4O PQ: 0 ANSI: 5
> [ 3.467213] ata5: SATA link down (SStatus 0 SControl 300)
> [ 3.792372] ata6: SATA link down (SStatus 0 SControl 300)
> [ 4.119125] ata7: SATA link down (SStatus 0 SControl 300)
> [ 4.447083] ata8: SATA link down (SStatus 0 SControl 300)
> [ 4.775039] ata9: SATA link down (SStatus 0 SControl 300)
> [ 5.102996] ata10: SATA link down (SStatus 0 SControl 300)
> [ 5.121569] sd 2:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
> [ 5.121702] sd 3:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
> [ 5.121804] sd 3:0:0:0: [sdb] Write Protect is off
> [ 5.121808] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
> [ 5.121847] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> [ 5.122077] sdb: sdb1 sdb2 sdb3 sdb4
> [ 5.154946] sd 2:0:0:0: [sda] Write Protect is off
> [ 5.155138] sd 3:0:0:0: [sdb] Attached SCSI disk
> [ 5.164473] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
> [ 5.164504] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> [ 5.173784] sda: sda1 sda2 sda3 sda4
> [ 5.187734] sd 2:0:0:0: [sda] Attached SCSI disk
> [ 5.202558] sr0: scsi3-mmc drive: 24x/24x cd/rw xa/form2 cdda tray
> [ 5.208896] Uniform CD-ROM driver Revision: 3.20
> [ 5.213793] sr 1:0:0:0: Attached scsi CD-ROM sr0
> [ 5.220070] sr 1:0:0:0: Attached scsi generic sg0 type 5
> [ 5.226118] sd 2:0:0:0: Attached scsi generic sg1 type 0
> [ 5.231740] sd 3:0:0:0: Attached scsi generic sg2 type 0
> [ 17.169398] scsi10 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0
> [ 17.169400] <Adaptec AIC7902 Ultra320 SCSI adapter>
> [ 17.169402] aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 101-133MHz, 512 SCBs
> [ 17.190011] aic79xx 0000:03:02.1: PCI->APIC IRQ transform: INT B -> IRQ 29
> [ 32.319397] scsi11 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0
> [ 32.319399] <Adaptec AIC7902 Ultra320 SCSI adapter>
> [ 32.319401] aic7902: Ultra320 Wide Channel B, SCSI Id=7, PCI-X 101-133MHz, 512 SCBs
> [ 32.468914] md: raid1 personality registered for level 1
> [ 32.495058] md: md0 stopped.
> [ 32.499399] md: bind<sdb1>
> [ 32.502428] md: bind<sda1>
> [ 32.506914] raid1: raid set md0 active with 2 out of 2 mirrors
> [ 32.512840] md0: detected capacity change from 0 to 501612544
> [ 32.520200] md0: unknown partition table
> [ 32.536981] md: md1 stopped.
> [ 32.541384] md: bind<sdb2>
> [ 32.544500] md: bind<sda2>
> [ 32.549187] raid1: raid set md1 active with 2 out of 2 mirrors
> [ 32.555125] md1: detected capacity change from 0 to 1003356160
> [ 32.562849] md1: unknown partition table
> [ 32.692551] md: md2 stopped.
> [ 32.696479] md: bind<sdb3>
> [ 32.699484] md: bind<sda3>
> [ 32.705657] raid1: raid set md2 active with 2 out of 2 mirrors
> [ 32.711577] md2: detected capacity change from 0 to 29997465600
> [ 32.720012] md2: unknown partition table
> [ 32.739258] md: md3 stopped.
> [ 32.745113] md: bind<sdb4>
> [ 32.748121] md: bind<sda4>
> [ 32.753506] raid1: raid set md3 active with 2 out of 2 mirrors
> [ 32.759448] md3: detected capacity change from 0 to 968699346944
> [ 32.767257] md3: unknown partition table
> [ 32.777468] device-mapper: uevent: version 1.0.3
> [ 32.782641] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
> [ 43.532470] alg: No test for xts(serpent) (xts(serpent-generic))
> [ 44.294711] kjournald starting. Commit interval 5 seconds
> [ 44.294729] EXT3-fs: mounted filesystem with ordered data mode.
> [ 45.863655] udev[383]: starting version 163
> [ 46.061212] EDAC MC: Ver: 2.1.0 Oct 31 2010
> [ 46.063253] input: PC Speaker as /devices/platform/pcspkr/input/input0
> [ 46.063669] i801_smbus 0000:00:1f.3: can't find IRQ for PCI INT B; probably buggy MP table
> [ 46.071999] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
> [ 46.078896] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
> [ 46.125639] EDAC e7xxx: tolm = f8000, remapbase = 200000, remaplimit = 208000
> [ 46.133015] EDAC MC0: Giving out device to 'e7xxx_edac' 'E7501': DEV 0000:00:00.0
> [ 46.140782] EDAC PCI0: Giving out device to module 'e7xxx_edac' controller 'EDAC PCI controller': DEV '0000:00:00.0' (POLLED)
> [ 46.195973] Intel 82802 RNG detected
> [ 46.558698] Error: Driver 'pcspkr' is already registered, aborting...
> [ 47.686885] EXT3 FS on dm-1, internal journal
> [ 48.221293] Clocksource tsc unstable (delta = 70832644 ns)
> [ 48.226983] Switching to clocksource jiffies
> [ 52.604346] loop: module loaded
> [ 54.100002] Adding 979832k swap on /dev/mapper/md1_crypt. Priority:-1 extents:1 across:979832k
> [ 55.259543] kjournald starting. Commit interval 5 seconds
> [ 55.311539] EXT3 FS on md0, internal journal
> [ 55.315508] EXT3-fs: mounted filesystem with ordered data mode.
> [ 55.375520] kjournald starting. Commit interval 5 seconds
> [ 55.375667] EXT3 FS on dm-2, internal journal
> [ 55.375667] EXT3-fs: mounted filesystem with ordered data mode.
> [ 55.435516] kjournald starting. Commit interval 5 seconds
> [ 55.435659] EXT3 FS on dm-3, internal journal
> [ 55.435659] EXT3-fs: mounted filesystem with ordered data mode.
> [ 56.560725] ADDRCONF(NETDEV_UP): eth1: link is not ready
> [ 56.563869] e1000: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX
> [ 56.576450] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
> [ 56.621084] ADDRCONF(NETDEV_UP): eth0: link is not ready
> [ 56.627873] e1000: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX
> [ 56.639472] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
> [ 66.763519] eth0: no IPv6 routers present
> [ 67.235519] eth1: no IPv6 routers present
>
> ** Model information
> not available
>
> ** Loaded modules:
> Module Size Used by
> loop 9761 0
> evdev 5609 0
> snd_pcm 47402 0
> snd_timer 12258 1 snd_pcm
> snd 34375 2 snd_pcm,snd_timer
> soundcore 3450 1 snd
> snd_page_alloc 5109 1 snd_pcm
> intel_rng 1965 0
> rng_core 2178 1 intel_rng
> e7xxx_edac 2876 0
> shpchp 21264 0
> pci_hotplug 18065 1 shpchp
> pcspkr 1207 0
> i2c_i801 6466 0
> edac_core 23121 3 e7xxx_edac
> serio_raw 2916 0
> i2c_core 12696 1 i2c_i801
> ext3 94196 4
> jbd 32161 1 ext3
> mbcache 3762 1 ext3
> serpent 16187 6
> xts 1701 3
> gf128mul 5106 1 xts
> dm_crypt 9264 3
> dm_mod 46086 18 dm_crypt
> raid1 16363 4
> md_mod 67325 5 raid1
> sg 15972 0
> sr_mod 10770 0
> cdrom 26487 1 sr_mod
> sd_mod 25865 10
> crc_t10dif 1012 1 sd_mod
> ata_generic 2047 0
> uhci_hcd 16141 0
> ehci_hcd 28255 0
> sata_mv 19820 8
> aic79xx 112740 0
> ata_piix 17784 0
> e1000 77809 0
> scsi_transport_spi 14866 1 aic79xx
> libata 116045 3 ata_generic,sata_mv,ata_piix
> usbcore 98721 3 uhci_hcd,ehci_hcd
> floppy 40931 0
> nls_base 4541 1 usbcore
> scsi_mod 101405 6 sg,sr_mod,sd_mod,aic79xx,scsi_transport_spi,libata
>
> *** Device statistics:
> Inter-| Receive | Transmit
> face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed
> lo: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
> eth0: 444756 3020 0 0 0 0 0 0 13445 176 0 0 0 0 0 0
> eth1: 420 7 0 0 0 0 0 0 468 6 0 0 0 0 0 0
>
> *** Protocol statistics:
> Ip:
> 239 total packets received
> 10 with invalid addresses
> 0 forwarded
> 0 incoming packets discarded
> 229 incoming packets delivered
> 166 requests sent out
> Icmp:
> 2 ICMP messages received
> 0 input ICMP message failed.
> ICMP input histogram:
> echo replies: 2
> 2 ICMP messages sent
> 0 ICMP messages failed
> ICMP output histogram:
> echo request: 2
> IcmpMsg:
> InType0: 2
> OutType8: 2
> Tcp:
> 7 active connections openings
> 0 passive connection openings
> 0 failed connection attempts
> 0 connection resets received
> 0 connections established
> 213 segments received
> 150 segments send out
> 0 segments retransmited
> 0 bad segments received.
> 3 resets sent
> Udp:
> 14 packets received
> 0 packets to unknown port received.
> 0 packet receive errors
> 14 packets sent
> UdpLite:
> TcpExt:
> 1 TCP sockets finished time wait in fast timer
> 174 packet headers predicted
> 13 acknowledgments not containing data payload received
> IpExt:
> InOctets: 274550
> OutOctets: 10485
>
> *** Device features:
> eth0: 0x10ba9
> eth1: 0x10ba9
> lo: 0x13865
>
> ** PCI devices:
> 00:00.0 Host bridge [0600]: Intel Corporation E7501 Memory Controller Hub [8086:254c] (rev 01)
> Subsystem: Super Micro Computer Inc Device [15d9:3580]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Capabilities: [40] Vendor Specific Information: Len=05 <?>
> Kernel driver in use: e7xxx_edac
>
> 00:00.1 Unassigned class [ff00]: Intel Corporation E7500/E7501 Host RASUM Controller [8086:2541] (rev 01)
> Subsystem: Super Micro Computer Inc Device [15d9:3580]
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
>
> 00:02.0 PCI bridge [0604]: Intel Corporation E7500/E7501 Hub Interface B PCI-to-PCI Bridge [8086:2543] (rev 01) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 64
> Bus: primary=00, secondary=01, subordinate=03, sec-latency=0
> I/O behind bridge: 00003000-00004fff
> Memory behind bridge: fc100000-fc8fffff
> Prefetchable memory behind bridge: f8000000-f80fffff
> Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
>
> 00:1d.0 USB Controller [0c03]: Intel Corporation 82801CA/CAM USB Controller #1 [8086:2482] (rev 02) (prog-if 00 [UHCI])
> Subsystem: Super Micro Computer Inc Device [15d9:3580]
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin A routed to IRQ 16
> Region 4: I/O ports at 2000 [size=32]
> Kernel driver in use: uhci_hcd
>
> 00:1d.1 USB Controller [0c03]: Intel Corporation 82801CA/CAM USB Controller #2 [8086:2484] (rev 02) (prog-if 00 [UHCI])
> Subsystem: Super Micro Computer Inc Device [15d9:3580]
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin B routed to IRQ 19
> Region 4: I/O ports at 2020 [size=32]
> Kernel driver in use: uhci_hcd
>
> 00:1d.2 USB Controller [0c03]: Intel Corporation 82801CA/CAM USB Controller #3 [8086:2487] (rev 02) (prog-if 00 [UHCI])
> Subsystem: Super Micro Computer Inc Device [15d9:3580]
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin C routed to IRQ 18
> Region 4: I/O ports at 2040 [size=32]
> Kernel driver in use: uhci_hcd
>
> 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev 42) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Bus: primary=00, secondary=04, subordinate=04, sec-latency=64
> I/O behind bridge: 00005000-00005fff
> Memory behind bridge: fc900000-fdffffff
> Prefetchable memory behind bridge: f8100000-f81fffff
> Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
>
> 00:1f.0 ISA bridge [0601]: Intel Corporation 82801CA LPC Interface Controller [8086:2480] (rev 02)
> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
>
> 00:1f.1 IDE interface [0101]: Intel Corporation 82801CA Ultra ATA Storage Controller [8086:248b] (rev 02) (prog-if 8a [Master SecP PriP])
> Subsystem: Super Micro Computer Inc Device [15d9:3580]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin A routed to IRQ 0
> Region 0: I/O ports at 01f0 [size=8]
> Region 1: I/O ports at 03f4 [size=1]
> Region 2: I/O ports at 0170 [size=8]
> Region 3: I/O ports at 0374 [size=1]
> Region 4: I/O ports at 2060 [size=16]
> Region 5: Memory at f8200000 (32-bit, non-prefetchable) [size=1K]
> Kernel driver in use: ata_piix
>
> 00:1f.3 SMBus [0c05]: Intel Corporation 82801CA/CAM SMBus Controller [8086:2483] (rev 02)
> Subsystem: Super Micro Computer Inc Device [15d9:3580]
> Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Interrupt: pin B routed to IRQ 0
> Region 4: I/O ports at 1100 [size=32]
> Kernel driver in use: i801_smbus
>
> 01:1c.0 PIC [0800]: Intel Corporation 82870P2 P64H2 I/OxAPIC [8086:1461] (rev 04) (prog-if 20 [IO(X)-APIC])
> Subsystem: Super Micro Computer Inc Device [15d9:3580]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Region 0: Memory at fc100000 (32-bit, non-prefetchable) [size=4K]
> Capabilities: [50] PCI-X non-bridge device
> Command: DPERE- ERO- RBC=512 OST=1
> Status: Dev=01:1c.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=512 DMOST=1 DMCRS=8 RSCEM- 266MHz- 533MHz-
>
> 01:1d.0 PCI bridge [0604]: Intel Corporation 82870P2 P64H2 Hub PCI Bridge [8086:1460] (rev 04) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 64, Cache Line Size: 64 bytes
> Bus: primary=01, secondary=02, subordinate=02, sec-latency=64
> I/O behind bridge: 00003000-00003fff
> Memory behind bridge: fc200000-fc7fffff
> Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort+ >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [50] PCI-X bridge device
> Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=133MHz
> Status: Dev=01:1d.0 64bit+ 133MHz+ SCD- USC- SCO- SRD-
> Upstream: Capacity=65535 CommitmentLimit=65535
> Downstream: Capacity=65535 CommitmentLimit=65535
>
> 01:1e.0 PIC [0800]: Intel Corporation 82870P2 P64H2 I/OxAPIC [8086:1461] (rev 04) (prog-if 20 [IO(X)-APIC])
> Subsystem: Super Micro Computer Inc Device [15d9:3580]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Region 0: Memory at fc101000 (32-bit, non-prefetchable) [size=4K]
> Capabilities: [50] PCI-X non-bridge device
> Command: DPERE- ERO- RBC=512 OST=1
> Status: Dev=01:1e.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=512 DMOST=1 DMCRS=8 RSCEM- 266MHz- 533MHz-
>
> 01:1f.0 PCI bridge [0604]: Intel Corporation 82870P2 P64H2 Hub PCI Bridge [8086:1460] (rev 04) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 64, Cache Line Size: 64 bytes
> Bus: primary=01, secondary=03, subordinate=03, sec-latency=64
> I/O behind bridge: 00004000-00004fff
> Memory behind bridge: fc800000-fc8fffff
> Prefetchable memory behind bridge: 00000000f8000000-00000000f80fffff
> Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort+ >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [50] PCI-X bridge device
> Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=66MHz
> Status: Dev=01:1f.0 64bit+ 133MHz+ SCD- USC- SCO- SRD-
> Upstream: Capacity=65535 CommitmentLimit=65535
> Downstream: Capacity=65535 CommitmentLimit=65535
>
> 02:01.0 SCSI storage controller [0100]: Marvell Technology Group Ltd. MV88SX6081 8-port SATA II PCI-X Controller [11ab:6081] (rev 09)
> Subsystem: Marvell Technology Group Ltd. Device [11ab:11ab]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 64, Cache Line Size: 128 bytes
> Interrupt: pin A routed to IRQ 48
> Region 0: Memory at fc200000 (64-bit, non-prefetchable) [size=1M]
> Region 2: I/O ports at 3000 [size=256]
> Capabilities: [40] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
> Address: 0000000000000000 Data: 0000
> Capabilities: [60] PCI-X non-bridge device
> Command: DPERE- ERO- RBC=512 OST=4
> Status: Dev=02:01.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=512 DMOST=4 DMCRS=8 RSCEM- 266MHz- 533MHz-
> Kernel driver in use: sata_mv
>
> 02:03.0 Ethernet controller [0200]: Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) [8086:1010] (rev 01)
> Subsystem: Intel Corporation PRO/1000 MT Dual Port Server Adapter [8086:1011]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 64 (63750ns min), Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 54
> Region 0: Memory at fc300000 (64-bit, non-prefetchable) [size=128K]
> Region 4: I/O ports at 3400 [size=64]
> Capabilities: [dc] Power Management version 2
> Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
> Capabilities: [e4] PCI-X non-bridge device
> Command: DPERE- ERO+ RBC=512 OST=1
> Status: Dev=02:03.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=2048 DMOST=1 DMCRS=16 RSCEM- 266MHz- 533MHz-
> Capabilities: [f0] MSI: Enable- Count=1/1 Maskable- 64bit+
> Address: 0000000000000000 Data: 0000
> Kernel driver in use: e1000
>
> 02:03.1 Ethernet controller [0200]: Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) [8086:1010] (rev 01)
> Subsystem: Intel Corporation PRO/1000 MT Dual Port Server Adapter [8086:1011]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 64 (63750ns min), Cache Line Size: 32 bytes
> Interrupt: pin B routed to IRQ 55
> Region 0: Memory at fc320000 (64-bit, non-prefetchable) [size=128K]
> Region 4: I/O ports at 3440 [size=64]
> Capabilities: [dc] Power Management version 2
> Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
> Capabilities: [e4] PCI-X non-bridge device
> Command: DPERE- ERO+ RBC=512 OST=1
> Status: Dev=02:03.1 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=2048 DMOST=1 DMCRS=16 RSCEM- 266MHz- 533MHz-
> Capabilities: [f0] MSI: Enable- Count=1/1 Maskable- 64bit+
> Address: 0000000000000000 Data: 0000
> Kernel driver in use: e1000
>
> 03:02.0 SCSI storage controller [0100]: Adaptec AIC-7902B U320 [9005:801d] (rev 10)
> Subsystem: Adaptec Device [9005:005e]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 64 (10000ns min, 6250ns max), Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 28
> Region 0: I/O ports at 4400 [disabled] [size=256]
> Region 1: Memory at fc800000 (64-bit, non-prefetchable) [size=8K]
> Region 3: I/O ports at 4000 [disabled] [size=256]
> [virtual] Expansion ROM at f8000000 [disabled] [size=512K]
> Capabilities: [dc] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [a0] MSI: Enable- Count=1/2 Maskable- 64bit+
> Address: 0000000000000000 Data: 0000
> Capabilities: [94] PCI-X non-bridge device
> Command: DPERE- ERO+ RBC=512 OST=8
> Status: Dev=03:02.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=512 DMOST=8 DMCRS=16 RSCEM- 266MHz- 533MHz-
> Kernel driver in use: aic79xx
>
> 03:02.1 SCSI storage controller [0100]: Adaptec AIC-7902B U320 [9005:801d] (rev 10)
> Subsystem: Adaptec Device [9005:005e]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 64 (10000ns min, 6250ns max), Cache Line Size: 32 bytes
> Interrupt: pin B routed to IRQ 29
> Region 0: I/O ports at 4c00 [disabled] [size=256]
> Region 1: Memory at fc802000 (64-bit, non-prefetchable) [size=8K]
> Region 3: I/O ports at 4800 [disabled] [size=256]
> [virtual] Expansion ROM at f8080000 [disabled] [size=512K]
> Capabilities: [dc] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [a0] MSI: Enable- Count=1/2 Maskable- 64bit+
> Address: 0000000000000000 Data: 0000
> Capabilities: [94] PCI-X non-bridge device
> Command: DPERE- ERO+ RBC=512 OST=8
> Status: Dev=03:02.1 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=512 DMOST=8 DMCRS=16 RSCEM- 266MHz- 533MHz-
> Kernel driver in use: aic79xx
>
> 04:01.0 VGA compatible controller [0300]: ATI Technologies Inc Rage XL [1002:4752] (rev 27) (prog-if 00 [VGA controller])
> Subsystem: ATI Technologies Inc Rage XL [1002:0008]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 64 (2000ns min), Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 11
> Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
> Region 1: I/O ports at 5000 [size=256]
> Region 2: Memory at fc900000 (32-bit, non-prefetchable) [size=4K]
> [virtual] Expansion ROM at f8100000 [disabled] [size=128K]
> Capabilities: [5c] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
>
>
> ** USB devices:
> Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
> Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
> Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
>
>
> -- System Information:
> Debian Release: squeeze/sid
> APT prefers testing
> APT policy: (500, 'testing')
> Architecture: i386 (i686)
>
> Kernel: Linux 2.6.32-5-xen-686 (SMP w/4 CPU cores)
> Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
> Shell: /bin/sh linked to /bin/dash
>
> Versions of packages linux-image-2.6.32-5-xen-686 depends on:
> ii debconf [debconf-2.0] 1.5.36 Debian configuration management sy
> ii initramfs-tools 0.98.5 tools for generating an initramfs
> ii linux-base 2.6.32-27 Linux image base package
> ii module-init-tools 3.12-1 tools for managing Linux kernel mo
>
> Versions of packages linux-image-2.6.32-5-xen-686 recommends:
> ii firmware-linux-free 2.6.32-27 Binary firmware for various driver
> ii libc6-xen 2.11.2-7 Embedded GNU C Library: Shared lib
>
> Versions of packages linux-image-2.6.32-5-xen-686 suggests:
> ii grub 0.97-63 GRand Unified Bootloader (dummy pa
> pn linux-doc-2.6.32 <none> (no description available)
>
> Versions of packages linux-image-2.6.32-5-xen-686 is related to:
> pn firmware-bnx2 <none> (no description available)
> pn firmware-bnx2x <none> (no description available)
> pn firmware-ipw2x00 <none> (no description available)
> pn firmware-ivtv <none> (no description available)
> pn firmware-iwlwifi <none> (no description available)
> pn firmware-linux <none> (no description available)
> pn firmware-linux-nonfree <none> (no description available)
> pn firmware-qlogic <none> (no description available)
> pn firmware-ralink <none> (no description available)
> ii xen-hypervisor-4.0-i386 [xen- 4.0.1-1 The Xen Hypervisor on i386
>
> -- debconf information:
> linux-image-2.6.32-5-xen-686/postinst/depmod-error-initrd-2.6.32-5-xen-686: false
> linux-image-2.6.32-5-xen-686/postinst/ignoring-do-bootloader-2.6.32-5-xen-686:
> linux-image-2.6.32-5-xen-686/prerm/removing-running-kernel-2.6.32-5-xen-686: true
> linux-image-2.6.32-5-xen-686/postinst/missing-firmware-2.6.32-5-xen-686:
>
>
>
>
>
--
Ian Campbell
Current Noise: Annihilator - Never, Neverland
*** Topic for #redhat: ReDHaT is the answer to all your problems. It
could be the start too!
Reply to: