Bug#602256: linux-image-2.6.32-5-amd64: Squeeze kernel (amd64/i386) won't boot on Lenny KVM/amd64 with vcpu > 1
Package: linux-2.6
Version: 2.6.32-27
Severity: important
Aftering install via beta 1 d-i on Lenny KVM/amd64 host, neither Squeeze amd64 or i386 will boot with vcpu more than 1. Booting in rescue mode shows it hanging after initializing USB. Both OSes boot correctly with vcpu = 1. Additionally, the beta 1 i386 installer will run with vcpu = 2, but the amd64 beta 1 installer will not.
-- Package-specific info:
** Version:
Linux version 2.6.32-5-amd64 (Debian 2.6.32-27) (maks@debian.org) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Sat Oct 30 14:18:21 UTC 2010
** Command line:
BOOT_IMAGE=/vmlinuz-2.6.32-5-amd64 root=UUID=9d0f2b04-6c07-44f4-a25b-10ccaf426bd3 ro quiet
** Not tainted
** Kernel log:
[ 0.323138] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.323277] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16450
[ 0.323560] 00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16450
[ 0.323649] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 0.323694] PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
[ 0.324331] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.324335] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.324410] mice: PS/2 mouse device common for all mice
[ 0.324696] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[ 0.324930] rtc_cmos 00:01: rtc core: registered rtc_cmos as rtc0
[ 0.324999] rtc0: alarms up to one day, 114 bytes nvram
[ 0.325006] cpuidle: using governor ladder
[ 0.325008] cpuidle: using governor menu
[ 0.325011] No iBFT detected.
[ 0.325306] TCP cubic registered
[ 0.325397] NET: Registered protocol family 10
[ 0.326068] lo: Disabled Privacy Extensions
[ 0.326251] Mobile IPv6
[ 0.326256] NET: Registered protocol family 17
[ 0.326335] PM: Resume from disk failed.
[ 0.326340] registered taskstats version 1
[ 0.326588] rtc_cmos 00:01: setting system clock to 2010-11-02 23:09:51 UTC (1288739391)
[ 0.326610] Initalizing network drop monitor service
[ 0.326628] Freeing unused kernel memory: 584k freed
[ 0.326798] Write protecting the kernel read-only data: 4232k
[ 0.388473] udev[46]: starting version 163
[ 0.700181] SCSI subsystem initialized
[ 0.724436] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
[ 0.724467] virtio-pci 0000:00:03.0: PCI INT A -> Link[LNKC] -> GSI 11 (level, high) -> IRQ 11
[ 0.724993] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
[ 0.725010] virtio-pci 0000:00:04.0: PCI INT A -> Link[LNKD] -> GSI 10 (level, high) -> IRQ 10
[ 0.726483] usbcore: registered new interface driver usbfs
[ 0.726592] usbcore: registered new interface driver hub
[ 0.729847] usbcore: registered new device driver usb
[ 0.738071] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.739523] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.739563] uhci_hcd 0000:00:01.2: PCI INT D -> Link[LNKD] -> GSI 10 (level, high) -> IRQ 10
[ 0.739594] uhci_hcd 0000:00:01.2: setting latency timer to 64
[ 0.739606] uhci_hcd 0000:00:01.2: UHCI Host Controller
[ 0.739636] uhci_hcd 0000:00:01.2: new USB bus registered, assigned bus number 1
[ 0.739729] uhci_hcd 0000:00:01.2: irq 10, io base 0x0000c020
[ 0.739806] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.739810] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.739812] usb usb1: Product: UHCI Host Controller
[ 0.739813] usb usb1: Manufacturer: Linux 2.6.32-5-amd64 uhci_hcd
[ 0.739814] usb usb1: SerialNumber: 0000:00:01.2
[ 0.739866] usb usb1: configuration #1 chosen from 1 choice
[ 0.739889] hub 1-0:1.0: USB hub found
[ 0.739896] hub 1-0:1.0: 2 ports detected
[ 0.740750] vda:
[ 0.741251] FDC 0 is a S82078B
[ 0.743046] vda1 vda2 vda3
[ 0.750192] libata version 3.00 loaded.
[ 0.752079] ata_piix 0000:00:01.1: version 2.13
[ 0.752162] ata_piix 0000:00:01.1: setting latency timer to 64
[ 0.752378] scsi0 : ata_piix
[ 0.754440] scsi1 : ata_piix
[ 0.754518] ata1: PATA max MWDMA2 cmd 0x1f0 ctl 0x3f6 bmdma 0xc000 irq 14
[ 0.754520] ata2: PATA max MWDMA2 cmd 0x170 ctl 0x376 bmdma 0xc008 irq 15
[ 0.912395] ata2.00: ATAPI: QEMU DVD-ROM, 0.9.1, max UDMA/100
[ 0.912805] ata2.00: configured for MWDMA2
[ 0.913218] scsi 1:0:0:0: CD-ROM QEMU QEMU DVD-ROM 0.9. PQ: 0 ANSI: 5
[ 0.922922] sr0: scsi3-mmc drive: 4x/4x xa/form2 tray
[ 0.922928] Uniform CD-ROM driver Revision: 3.20
[ 0.923136] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 0.935845] sr 1:0:0:0: Attached scsi generic sg0 type 5
[ 1.000886] PM: Starting manual resume from disk
[ 1.000888] PM: Resume from partition 254:2
[ 1.000889] PM: Checking hibernation image.
[ 1.000971] PM: Error -22 checking image file
[ 1.000972] PM: Resume from disk failed.
[ 1.041735] EXT4-fs (vda3): mounted filesystem with ordered data mode
[ 1.644699] udev[278]: starting version 163
[ 1.842212] input: PC Speaker as /devices/platform/pcspkr/input/input2
[ 2.023500] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 2.023506] ACPI: Power Button [PWRF]
[ 2.051463] processor LNXCPU:00: registered as cooling_device0
[ 2.051515] ACPI Warning for \_PR_.CPU1._MAT: Return type mismatch - found Integer, expected Buffer (20090903/nspredef-1006)
[ 2.051575] ACPI Warning for \_PR_.CPU2._MAT: Return type mismatch - found Integer, expected Buffer (20090903/nspredef-1006)
[ 2.051629] ACPI Warning for \_PR_.CPU3._MAT: Return type mismatch - found Integer, expected Buffer (20090903/nspredef-1006)
[ 2.051682] ACPI Warning for \_PR_.CPU4._MAT: Return type mismatch - found Integer, expected Buffer (20090903/nspredef-1006)
[ 2.051735] ACPI Warning for \_PR_.CPU5._MAT: Return type mismatch - found Integer, expected Buffer (20090903/nspredef-1006)
[ 2.051788] ACPI Warning for \_PR_.CPU6._MAT: Return type mismatch - found Integer, expected Buffer (20090903/nspredef-1006)
[ 2.051841] ACPI Warning for \_PR_.CPU7._MAT: Return type mismatch - found Integer, expected Buffer (20090903/nspredef-1006)
[ 2.051900] ACPI Warning for \_PR_.CPU8._MAT: Return type mismatch - found Integer, expected Buffer (20090903/nspredef-1006)
[ 2.051962] ACPI Warning for \_PR_.CPU9._MAT: Return type mismatch - found Integer, expected Buffer (20090903/nspredef-1006)
[ 2.065211] ACPI Warning for \_PR_.CPUA._MAT: Return type mismatch - found Integer, expected Buffer (20090903/nspredef-1006)
[ 2.065280] ACPI Warning for \_PR_.CPUB._MAT: Return type mismatch - found Integer, expected Buffer (20090903/nspredef-1006)
[ 2.065333] ACPI Warning for \_PR_.CPUC._MAT: Return type mismatch - found Integer, expected Buffer (20090903/nspredef-1006)
[ 2.065387] ACPI Warning for \_PR_.CPUD._MAT: Return type mismatch - found Integer, expected Buffer (20090903/nspredef-1006)
[ 2.065449] ACPI Warning for \_PR_.CPUE._MAT: Return type mismatch - found Integer, expected Buffer (20090903/nspredef-1006)
[ 2.087790] piix4_smbus 0000:00:01.3: SMBus Host Controller at 0xb100, revision 0
[ 2.197447] Error: Driver 'pcspkr' is already registered, aborting...
[ 2.471713] Adding 508024k swap on /dev/vda2. Priority:-1 extents:1 across:508024k
[ 2.493469] input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input4
[ 2.668474] loop: module loaded
[ 3.019749] kjournald starting. Commit interval 5 seconds
[ 3.019808] EXT3 FS on vda1, internal journal
[ 3.019813] EXT3-fs: mounted filesystem with ordered data mode.
[ 7.816586] JBD: barrier-based sync failed on vda3-8 - disabling barriers
** Model information
sys_vendor:
product_name:
product_version:
chassis_vendor:
chassis_version:
bios_vendor: QEMU
bios_version: QEMU
** Loaded modules:
Module Size Used by
ext3 106534 1
jbd 37101 1 ext3
loop 11799 0
snd_pcm 60503 0
i2c_piix4 8328 0
snd_timer 15582 1 snd_pcm
psmouse 49777 0
serio_raw 3752 0
evdev 7352 0
i2c_core 15712 1 i2c_piix4
button 4650 0
processor 29951 0
snd 46446 2 snd_pcm,snd_timer
soundcore 4598 1 snd
snd_page_alloc 6249 1 snd_pcm
pcspkr 1699 0
ext4 289097 1
mbcache 5050 2 ext3,ext4
jbd2 67015 1 ext4
crc16 1319 1 ext4
sg 18744 0
sr_mod 12602 0
cdrom 29415 1 sr_mod
ata_generic 3015 0
ata_piix 21124 0
virtio_blk 4225 4
uhci_hcd 18521 0
ehci_hcd 31135 0
virtio_net 10529 0
thermal 11674 0
libata 133616 2 ata_generic,ata_piix
floppy 49087 0
thermal_sys 11942 2 processor,thermal
virtio_pci 5535 0
virtio_ring 3258 1 virtio_pci
virtio 3309 3 virtio_blk,virtio_net,virtio_pci
usbcore 121954 3 uhci_hcd,ehci_hcd
nls_base 6377 1 usbcore
scsi_mod 122117 3 sg,sr_mod,libata
** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
allow-hotplug eth0
iface eth0 inet dhcp
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 1000
link/ether 54:52:00:44:4f:76 brd ff:ff:ff:ff:ff:ff
inet 10.2.1.148/24 brd 10.236.174.255 scope global eth0
inet6 2001:470:1f07:760:5652:ff:fe44:4f76/64 scope global dynamic
valid_lft 2591608sec preferred_lft 604408sec
inet6 fe80::5652:ff:fe44:4f76/64 scope link
valid_lft forever preferred_lft forever
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed
lo: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
eth0: 4719110 3266 0 0 0 0 0 0 120162 1746 0 0 0 0 0 0
*** Protocol statistics:
Ip:
3215 total packets received
3 with invalid addresses
0 forwarded
0 incoming packets discarded
3183 incoming packets delivered
1707 requests sent out
Icmp:
0 ICMP messages received
0 input ICMP message failed.
ICMP input histogram:
0 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
Tcp:
4 active connections openings
0 passive connection openings
0 failed connection attempts
0 connection resets received
0 connections established
3117 segments received
1718 segments send out
0 segments retransmited
0 bad segments received.
2 resets sent
Udp:
8 packets received
0 packets to unknown port received.
0 packet receive errors
8 packets sent
UdpLite:
TcpExt:
2 TCP sockets finished time wait in fast timer
2956 packet headers predicted
7 acknowledgments not containing data payload received
IpExt:
InBcastPkts: 75
InOctets: 4664603
OutOctets: 91639
InBcastOctets: 9653
*** Device features:
eth0: 0x20
lo: 0x13865
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 440FX - 82441FX PMC [Natoma] [8086:1237] (rev 02)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:01.0 ISA bridge [0601]: Intel Corporation 82371SB PIIX3 ISA [Natoma/Triton II] [8086:7000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:01.1 IDE interface [0101]: Intel Corporation 82371SB PIIX3 IDE [Natoma/Triton II] [8086:7010] (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
Region 4: I/O ports at c000 [size=16]
Kernel driver in use: ata_piix
00:01.2 USB Controller [0c03]: Intel Corporation 82371SB PIIX3 USB [Natoma/Triton II] [8086:7020] (rev 01) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin D routed to IRQ 10
Region 4: I/O ports at c020 [size=32]
Kernel driver in use: uhci_hcd
00:01.3 Bridge [0680]: Intel Corporation 82371AB/EB/MB PIIX4 ACPI [8086:7113] (rev 03)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 9
Kernel driver in use: piix4_smbus
00:02.0 VGA compatible controller [0300]: Cirrus Logic GD 5446 [1013:00b8] (prog-if 00 [VGA controller])
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=32M]
Region 1: Memory at f2000000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled]
00:03.0 Ethernet controller [0200]: Red Hat, Inc Virtio network device [1af4:1000]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at c040 [size=32]
Kernel driver in use: virtio-pci
00:04.0 Mass storage controller [0180]: Red Hat, Inc Virtio block device [1af4:1001]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at c080 [size=64]
Kernel driver in use: virtio-pci
** USB devices:
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
-- System Information:
Debian Release: squeeze/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.32-5-amd64 (SMP w/1 CPU core)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-2.6.32-5-amd64 depends on:
ii debconf [debconf-2.0] 1.5.36 Debian configuration management sy
ii initramfs-tools [linux-initra 0.98.5 tools for generating an initramfs
ii linux-base 2.6.32-27 Linux image base package
ii module-init-tools 3.12-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.32-5-amd64 recommends:
pn firmware-linux-free <none> (no description available)
Versions of packages linux-image-2.6.32-5-amd64 suggests:
pn grub | lilo <none> (no description available)
pn linux-doc-2.6.32 <none> (no description available)
Versions of packages linux-image-2.6.32-5-amd64 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-linux <none> (no description available)
pn firmware-linux-nonfree <none> (no description available)
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn xen-hypervisor <none> (no description available)
-- debconf information:
linux-image-2.6.32-5-amd64/postinst/ignoring-do-bootloader-2.6.32-5-amd64:
linux-image-2.6.32-5-amd64/postinst/depmod-error-initrd-2.6.32-5-amd64: false
linux-image-2.6.32-5-amd64/prerm/removing-running-kernel-2.6.32-5-amd64: true
linux-image-2.6.32-5-amd64/postinst/missing-firmware-2.6.32-5-amd64:
Reply to: