Package: linux-2.6
Version: 2.6.32-23
Severity: normal
My system is a Helios single-board computer, with specs:
CPU: Vortex86 SoC (800MHz) - according to Diamond Systems, "a 486
class pre-pentium integrated circuit"
RAM: 256MB
Storage: 4GB compact flash (I disabled write caching for this)
Swap: partitioned, about 236MB (just what the installer recommended)
Kernel: 2.6.32-5-486
Debian: Squeeze (from installer daily build, updated after install)
When I install avahi-daemon, I get a kernel panic. I have attached a
log of a serial session reproducing this. The log also contains lspci
and ifconfig output, but here is the ethernet controller line:
00:08.0 Ethernet controller: RDC Semiconductor, Inc. R6040 MAC Controller
It seems to be related to IPv6, because if I boot with
"ipv6.disable=1", there is no crash. It also does not happen with
linux-image-2.6.36-rc6-486 from experimental. I took an image of the
CF contents before doing this, but I can't reproduce this under qemu.
I have another kernel built from the same config file as
linux-image-2.6.32-5-486 but with the debugging package built as well;
let me know if you want me to repeat it all with that.
-- Package-specific info:
** Version:
Linux version 2.6.32-5-486 (Debian 2.6.32-23) (dannf@debian.org) (gcc
version 4.3.5 (Debian 4.3.5-3) ) #1 Sat Sep 18 01:43:00 UTC 2010
** Command line:
BOOT_IMAGE=/boot/vmlinuz-2.6.32-5-486
root=UUID=5b129c11-e746-45ea-908d-15cd22ee702a ro pnpbios=off
console=tty0 console=ttyS0,115200n8
** Not tainted
** Kernel log:
[ 6.173121] registered taskstats version 1
[ 6.178248] rtc_cmos rtc_cmos: setting system clock to 2010-10-13
10:11:51 UTC (1286964711)
[ 6.186972] Initalizing network drop monitor service
[ 6.192359] Freeing unused kernel memory: 436k freed
[ 6.200082] Write protecting the kernel text: 2336k
[ 6.205268] Write protecting the kernel read-only data: 892k
[ 6.378050] udev: starting version 160
[ 7.277146] usbcore: registered new interface driver usbfs
[ 7.570128] usbcore: registered new interface driver hub
[ 7.577875] usbcore: registered new device driver usb
[ 7.609252] SCSI subsystem initialized
[ 7.658487] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 7.702737] ehci_hcd 0000:00:0a.1: EHCI Host Controller
[ 7.709626] ehci_hcd 0000:00:0a.1: new USB bus registered, assigned
bus number 1
[ 7.740958] ehci_hcd 0000:00:0a.1: irq 15, io mem 0x10022000
[ 8.099943] libata version 3.00 loaded.
[ 8.147138] ehci_hcd 0000:00:0a.1: USB 2.0 started, EHCI 1.00
[ 8.154539] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 8.161510] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 8.168862] usb usb1: Product: EHCI Host Controller
[ 8.173848] usb usb1: Manufacturer: Linux 2.6.32-5-486 ehci_hcd
[ 8.179887] usb usb1: SerialNumber: 0000:00:0a.1
[ 8.185991] usb usb1: configuration #1 chosen from 1 choice
[ 8.192585] hub 1-0:1.0: USB hub found
[ 8.197178] hub 1-0:1.0: 2 ports detected
[ 8.204376] r6040: RDC R6040 NAPI net driver,version 0.25 (20Aug2009)
[ 8.224507] scsi0 : pata_it821x
[ 8.231691] scsi1 : pata_it821x
[ 8.236267] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f4 bmdma 0xfff0 irq 14
[ 8.243433] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x374 bmdma 0xfff8 irq 14
[ 8.250908] ehci_hcd 0000:00:0b.1: EHCI Host Controller
[ 8.258997] ehci_hcd 0000:00:0b.1: new USB bus registered, assigned
bus number 2
[ 8.288737] ehci_hcd 0000:00:0b.1: irq 9, io mem 0x10022100
[ 8.305311] ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00
[ 8.311396] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 8.318352] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 8.325720] usb usb2: Product: EHCI Host Controller
[ 8.330712] usb usb2: Manufacturer: Linux 2.6.32-5-486 ehci_hcd
[ 8.336742] usb usb2: SerialNumber: 0000:00:0b.1
[ 8.344065] usb usb2: configuration #1 chosen from 1 choice
[ 8.350637] hub 2-0:1.0: USB hub found
[ 8.354636] hub 2-0:1.0: 2 ports detected
[ 8.477287] ata1.00: CFA: 4GB ATA Flash Disk, AD B612J, max UDMA/66
[ 8.483732] ata1.00: 8000496 sectors, multi 0: LBA
[ 8.488859] ata1.00: limited to UDMA/33 due to 40-wire cable
[ 8.499842] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 8.507711] ohci_hcd 0000:00:0a.0: OHCI Host Controller
[ 8.513640] ata1.00: configured for UDMA/33
[ 8.518765] scsi 0:0:0:0: Direct-Access ATA 4GB ATA Flash
Di AD B PQ: 0 ANSI: 5
[ 8.527180] ohci_hcd 0000:00:0a.0: new USB bus registered, assigned
bus number 3
[ 8.537688] ohci_hcd 0000:00:0a.0: irq 6, io mem 0x10020000
[ 8.628373] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 8.635348] usb usb3: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 8.642699] usb usb3: Product: OHCI Host Controller
[ 8.647681] usb usb3: Manufacturer: Linux 2.6.32-5-486 ohci_hcd
[ 8.653708] usb usb3: SerialNumber: 0000:00:0a.0
[ 8.659713] usb usb3: configuration #1 chosen from 1 choice
[ 8.666282] hub 3-0:1.0: USB hub found
[ 8.670282] hub 3-0:1.0: 2 ports detected
[ 8.674934] ohci_hcd 0000:00:0b.0: OHCI Host Controller
[ 8.681809] ohci_hcd 0000:00:0b.0: new USB bus registered, assigned
bus number 4
[ 8.689516] ohci_hcd 0000:00:0b.0: irq 5, io mem 0x10021000
[ 8.756778] Clocksource tsc unstable (delta = 72079157 ns)
[ 8.788527] Switching to clocksource pit
[ 8.897646] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 8.904645] usb usb4: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 8.908588] usb usb4: Product: OHCI Host Controller
[ 8.911985] usb usb4: Manufacturer: Linux 2.6.32-5-486 ohci_hcd
[ 8.915051] usb usb4: SerialNumber: 0000:00:0b.0
[ 8.921218] usb usb4: configuration #1 chosen from 1 choice
[ 8.927804] hub 4-0:1.0: USB hub found
[ 8.931817] hub 4-0:1.0: 2 ports detected
[ 8.953366] sd 0:0:0:0: [sda] 8000496 512-byte logical blocks:
(4.09 GB/3.81 GiB)
[ 8.967940] sd 0:0:0:0: [sda] Write Protect is off
[ 8.968952] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 8.976497] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 8.997519] sda: sda1 sda2 < sda5 >
[ 9.025930] sd 0:0:0:0: [sda] Attached SCSI disk
[ 9.390135] PM: Starting manual resume from disk
[ 9.394945] PM: Resume from partition 8:5
[ 9.394961] PM: Checking hibernation image.
[ 9.395904] PM: Error -22 checking image file
[ 9.395925] PM: Resume from disk failed.
[ 9.671618] EXT3-fs: INFO: recovery required on readonly filesystem.
[ 9.675417] EXT3-fs: write access will be enabled during recovery.
[ 12.324271] kjournald starting. Commit interval 5 seconds
[ 12.327899] EXT3-fs: recovery complete.
[ 12.380094] EXT3-fs: mounted filesystem with ordered data mode.
[ 13.308709] udev: starting version 160
[ 15.299313] input: PC Speaker as /devices/platform/pcspkr/input/input1
[ 15.304406] PCSP: Timer resolution is not sufficient (4000250nS)
[ 15.306594] PCSP: Make sure you have HPET and ACPI enabled.
[ 15.312306] PC-Speaker initialization failed.
[ 15.316267] pcspkr: probe of pcspkr failed with error -5
[ 15.339171] Error: Driver 'pcspkr' is already registered, aborting...
[ 16.607145] Adding 231416k swap on /dev/sda5. Priority:-1
extents:1 across:231416k
[ 16.845315] EXT3 FS on sda1, internal journal
[ 17.329473] loop: module loaded
[ 19.617326] eth0: link up, 100Mbps, half-duplex, lpa 0x40A1
[ 30.582013] eth0: no IPv6 routers present
** Model information
not available
** Loaded modules:
Module Size Used by
loop 9569 0
snd_pcsp 5185 0
snd_pcm 46098 1 snd_pcsp
snd_timer 12292 1 snd_pcm
snd 34102 3 snd_pcsp,snd_pcm,snd_timer
soundcore 3294 1 snd
serio_raw 2912 0
snd_page_alloc 5021 1 snd_pcm
psmouse 48410 0
evdev 5520 1
ext3 92740 1
jbd 27954 1 ext3
mbcache 3482 1 ext3
sd_mod 25825 3
crc_t10dif 1012 1 sd_mod
ohci_hcd 17072 0
pata_it821x 6574 2
libata 117275 1 pata_it821x
r6040 8164 0
ehci_hcd 27989 0
scsi_mod 102265 2 sd_mod,libata
usbcore 98145 3 ohci_hcd,ehci_hcd
mii 2654 1 r6040
nls_base 4445 1 usbcore
** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
allow-hotplug eth0
iface eth0 inet dhcp
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
state UNKNOWN qlen 1000
link/ether 00:1b:eb:69:08:e4 brd ff:ff:ff:ff:ff:ff
inet 192.168.1.54/24 brd 192.168.1.255 scope global eth0
inet6 fe80::21b:ebff:fe69:8e4/64 scope link
valid_lft forever preferred_lft forever
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed
multicast|bytes packets errs drop fifo colls carrier compressed
lo: 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0
eth0: 45939 420 0 0 0 0 0 2
3339 36 0 0 0 0 0 0
*** Protocol statistics:
Ip:
360 total packets received
1 with invalid addresses
0 forwarded
0 incoming packets discarded
359 incoming packets delivered
26 requests sent out
Icmp:
0 ICMP messages received
0 input ICMP message failed.
ICMP input histogram:
0 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
Tcp:
3 active connections openings
0 passive connection openings
0 failed connection attempts
0 connection resets received
0 connections established
17 segments received
18 segments send out
0 segments retransmited
0 bad segments received.
3 resets sent
Udp:
8 packets received
0 packets to unknown port received.
0 packet receive errors
8 packets sent
UdpLite:
TcpExt:
3 packet headers predicted
6 acknowledgments not containing data payload received
IpExt:
InMcastPkts: 2
InBcastPkts: 332
InOctets: 37295
OutOctets: 2039
InMcastOctets: 64
InBcastOctets: 25397
*** Device features:
eth0: 0x0
lo: 0x13865
** PCI devices:
00:00.0 Host bridge [0600]: RDC Semiconductor, Inc. R6021 Host Bridge
[17f3:6021] (rev 01)
Control: I/O- Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
00:04.0 VGA compatible controller [0300]: XGI Technology Inc. (eXtreme
Graphics Innovation) Z7/Z9 (XG20 core) [18ca:0020] (prog-if 00 [VGA
controller])
Subsystem: XGI Technology Inc. (eXtreme Graphics Innovation) Z7/Z9
(XG20 core) [18ca:0020]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
BIST result: 00
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Region 1: Memory at fefc0000 (32-bit, non-prefetchable) [size=256K]
Region 2: I/O ports at ef80 [size=128]
Expansion ROM at <unassigned> [disabled]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
00:07.0 ISA bridge [0601]: RDC Semiconductor, Inc. R6031 ISA Bridge
[17f3:6031] (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=?? >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
00:08.0 Ethernet controller [0200]: RDC Semiconductor, Inc. R6040 MAC
Controller [17f3:6040]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (750ns min, 2000ns max)
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at ee00 [size=256]
Region 1: Memory at fefbb400 (32-bit, non-prefetchable) [size=256]
Expansion ROM at fefa0000 [disabled] [size=64K]
Kernel driver in use: r6040
00:0a.0 USB Controller [0c03]: RDC Semiconductor, Inc. R6060 USB 1.1
Controller [17f3:6060] (rev 11) (prog-if 10 [OHCI])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 6
Region 0: Memory at 10020000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:0a.1 USB Controller [0c03]: RDC Semiconductor, Inc. R6061 USB 2.0
Controller [17f3:6061] (rev 02) (prog-if 20 [EHCI])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 15
Region 0: Memory at 10022000 (32-bit, non-prefetchable) [size=256]
Kernel driver in use: ehci_hcd
00:0b.0 USB Controller [0c03]: RDC Semiconductor, Inc. R6060 USB 1.1
Controller [17f3:6060] (rev 11) (prog-if 10 [OHCI])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 5
Region 0: Memory at 10021000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:0b.1 USB Controller [0c03]: RDC Semiconductor, Inc. R6061 USB 2.0
Controller [17f3:6061] (rev 02) (prog-if 20 [EHCI])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 9
Region 0: Memory at 10022100 (32-bit, non-prefetchable) [size=256]
Kernel driver in use: ehci_hcd
00:0c.0 Mass storage controller [0180]: RDC Semiconductor, Inc. R1010
IDE Controller [17f3:1010] (rev 13)
Subsystem: RDC Semiconductor, Inc. R1010 IDE Controller [17f3:1010]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (2000ns min, 2000ns max)
Interrupt: pin A routed to IRQ 14
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=4]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=4]
Region 4: I/O ports at fff0 [size=16]
[virtual] Expansion ROM at 10000000 [disabled] [size=128K]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pata_it821x
** USB devices:
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: squeeze/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: i386 (i586)
Kernel: Linux 2.6.32-5-486
Locale: LANG=en_AU.UTF-8, LC_CTYPE=en_AU.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-2.6.32-5-486 depends on:
ii debconf [debconf-2.0] 1.5.35 Debian configuration management sy
ii initramfs-tools [linux-initra 0.98.4 tools for generating an initramfs
ii linux-base 2.6.32-23 Linux image base package
ii module-init-tools 3.12-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.32-5-486 recommends:
pn firmware-linux-free <none> (no description available)
Versions of packages linux-image-2.6.32-5-486 suggests:
pn grub | lilo <none> (no description available)
pn linux-doc-2.6.32 <none> (no description available)
Versions of packages linux-image-2.6.32-5-486 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-linux <none> (no description available)
pn firmware-linux-nonfree <none> (no description available)
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn xen-hypervisor <none> (no description available)
-- debconf information:
linux-image-2.6.32-5-486/prerm/removing-running-kernel-2.6.32-5-486: true
linux-image-2.6.32-5-486/postinst/ignoring-do-bootloader-2.6.32-5-486:
linux-image-2.6.32-5-486/postinst/depmod-error-initrd-2.6.32-5-486: false
linux-image-2.6.32-5-486/postinst/missing-firmware-2.6.32-5-486:
Attachment:
2.6.32-5-486-crash.log
Description: Binary data