Bug#597662: linux-image-2.6.32-bpo.5-amd64: 60 second pause during boot: "eth0: unable to apply firmware patch"
Package: linux-2.6
Version: 2.6.32-23~bpo50+1
Severity: normal
When booting up, there is a 60 second pause with these messages:
[ 2.454863] Uniform CD-ROM driver Revision: 3.20
[ 2.454961] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 2.466393] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 2.466849] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 61.088047] eth0: unable to apply firmware patch
[ 61.987101] PM: Starting manual resume from disk
[ 61.987104] PM: Resume from partition 8:2
Full dmesg output is attached.
-- Package-specific info:
** Version:
Linux version 2.6.32-bpo.5-amd64 (Debian 2.6.32-23~bpo50+1) (norbert@tretkowski.de) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) #1 SMP Sat Sep 18 19:03:14 UTC 2010
** Command line:
BOOT_IMAGE=/boot/vmlinuz-2.6.32-bpo.5-amd64 root=UUID=b25673dd-6844-4fc6-8c4d-90f5d52e0b9d ro quiet
** Not tainted
** Kernel log:
[ 66.939216] ACPI: Battery Slot [BAT1] (battery present)
[ 66.979017] input: PS/2 Mouse as /devices/platform/i8042/serio1/input/input7
[ 67.008298] ACPI: AC Adapter [ACAD] (off-line)
[ 67.025103] input: AlpsPS/2 ALPS GlidePoint as /devices/platform/i8042/serio1/input/input8
[ 67.068301] phy0: Selected rate control algorithm 'iwl-agn-rs'
[ 67.074729] alloc irq_desc for 22 on node -1
[ 67.074732] alloc kstat_irqs on node -1
[ 67.074739] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 67.074779] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 67.209878] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input9
[ 67.220444] input: HDA Intel Mic at Ext Front Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[ 67.220502] input: HDA Intel HP Out at Ext Front Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[ 69.471952] Adding 3903784k swap on /dev/sda2. Priority:-1 extents:1 across:3903784k
[ 69.526074] EXT3 FS on sda3, internal journal
[ 70.401520] loop: module loaded
[ 72.873784] r8169: eth0: link down
[ 72.874095] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 75.852512] lp: driver loaded but no devices found
[ 75.906151] ppdev: user-space parallel port driver
[ 83.758912] Bluetooth: Core ver 2.15
[ 83.758975] NET: Registered protocol family 31
[ 83.758978] Bluetooth: HCI device and connection manager initialized
[ 83.758983] Bluetooth: HCI socket layer initialized
[ 83.800661] Bluetooth: L2CAP ver 2.14
[ 83.800665] Bluetooth: L2CAP socket layer initialized
[ 84.018060] Bluetooth: RFCOMM TTY layer initialized
[ 84.018066] Bluetooth: RFCOMM socket layer initialized
[ 84.018069] Bluetooth: RFCOMM ver 1.11
[ 84.355390] iwlagn 0000:0e:00.0: firmware: requesting iwlwifi-5000-2.ucode
[ 84.454910] iwlagn 0000:0e:00.0: iwlwifi-5000-2.ucode firmware file req failed: -2
[ 84.455001] iwlagn 0000:0e:00.0: firmware: requesting iwlwifi-5000-1.ucode
[ 84.541737] iwlagn 0000:0e:00.0: Loaded firmware iwlwifi-5000-1.ucode, which is deprecated. Please use API v2 instead.
[ 84.541834] iwlagn 0000:0e:00.0: Firmware has old API version. Expected v2, got v1. New firmware can be obtained from http://www.intellinuxwireless.org.
[ 84.541928] iwlagn 0000:0e:00.0: loaded firmware version 5.4.1.16
[ 84.719364] Registered led device: iwl-phy0::radio
[ 84.719392] Registered led device: iwl-phy0::assoc
[ 84.719422] Registered led device: iwl-phy0::RX
[ 84.719447] Registered led device: iwl-phy0::TX
[ 84.732898] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 87.704523] [drm] Initialized drm 1.1.0 20060810
[ 87.770442] pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 87.770448] pci 0000:00:02.0: setting latency timer to 64
[ 87.787230] alloc irq_desc for 33 on node -1
[ 87.787234] alloc kstat_irqs on node -1
[ 87.787243] pci 0000:00:02.0: irq 33 for MSI/MSI-X
[ 87.801781] acpi device:05: registered as cooling_device2
[ 87.802366] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:01/input/input12
[ 87.802468] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 87.802520] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 107.915853] CPUFREQ: Per core ondemand sysfs interface is deprecated - up_threshold
[ 107.929436] CPUFREQ: Per core ondemand sysfs interface is deprecated - ignore_nice_load
[ 115.644799] Registered led device: iwl-phy0::radio
[ 115.644828] Registered led device: iwl-phy0::assoc
[ 115.644853] Registered led device: iwl-phy0::RX
[ 115.644878] Registered led device: iwl-phy0::TX
[ 115.656936] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 126.493063] wlan0: direct probe to AP 00:30:bd:fd:b7:87 (try 1)
[ 126.493093] wlan0: deauthenticating from 00:30:bd:fd:b7:87 by local choice (reason=3)
[ 126.493120] wlan0: direct probe to AP 00:30:bd:fd:b7:87 (try 1)
[ 126.495208] wlan0: direct probe responded
[ 126.495213] wlan0: authenticate with AP 00:30:bd:fd:b7:87 (try 1)
[ 126.500267] wlan0: authenticated
[ 126.500300] wlan0: associate with AP 00:30:bd:fd:b7:87 (try 1)
[ 126.502681] wlan0: RX AssocResp from 00:30:bd:fd:b7:87 (capab=0x411 status=0 aid=4)
[ 126.502687] wlan0: associated
[ 126.517354] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 144.465038] wlan0: no IPv6 routers present
[ 1052.304179] No probe response from AP 00:30:bd:fd:b7:87 after 500ms, disconnecting.
[ 1066.574811] Registered led device: iwl-phy0::radio
[ 1066.574840] Registered led device: iwl-phy0::assoc
[ 1066.574868] Registered led device: iwl-phy0::RX
[ 1066.574900] Registered led device: iwl-phy0::TX
[ 1066.584744] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1087.110991] wlan0: direct probe to AP 00:30:bd:fd:b7:87 (try 1)
[ 1087.111012] wlan0: deauthenticating from 00:30:bd:fd:b7:87 by local choice (reason=3)
[ 1087.111030] wlan0: direct probe to AP 00:30:bd:fd:b7:87 (try 1)
[ 1087.113137] wlan0: direct probe responded
[ 1087.113142] wlan0: authenticate with AP 00:30:bd:fd:b7:87 (try 1)
[ 1087.117948] wlan0: authenticated
[ 1087.117986] wlan0: associate with AP 00:30:bd:fd:b7:87 (try 1)
[ 1087.120247] wlan0: RX AssocResp from 00:30:bd:fd:b7:87 (capab=0x411 status=0 aid=4)
[ 1087.120254] wlan0: associated
[ 1087.131777] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 1104.180032] wlan0: no IPv6 routers present
[ 2592.316250] No probe response from AP 00:30:bd:fd:b7:87 after 500ms, disconnecting.
[ 2610.517623] Registered led device: iwl-phy0::radio
[ 2610.518179] Registered led device: iwl-phy0::assoc
[ 2610.518696] Registered led device: iwl-phy0::RX
[ 2610.519196] Registered led device: iwl-phy0::TX
[ 2610.526259] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2676.918710] wlan0: deauthenticating from 00:30:bd:fd:b7:87 by local choice (reason=3)
[ 2676.918806] wlan0: direct probe to AP 00:30:bd:fd:b7:87 (try 1)
[ 2676.922706] wlan0: direct probe responded
[ 2676.922713] wlan0: authenticate with AP 00:30:bd:fd:b7:87 (try 1)
[ 2676.926736] wlan0: authenticated
[ 2676.926758] wlan0: associate with AP 00:30:bd:fd:b7:87 (try 1)
[ 2676.939519] wlan0: RX AssocResp from 00:30:bd:fd:b7:87 (capab=0x411 status=0 aid=4)
[ 2676.939524] wlan0: associated
[ 2676.944043] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 2693.704128] wlan0: no IPv6 routers present
** Model information
sys_vendor: Dell Inc.
product_name: Vostro 1520
product_version: Null
chassis_vendor: Dell Inc.
chassis_version: N/A
bios_vendor: Dell Inc.
bios_version: A02
board_vendor: Dell Inc.
board_name: 0T816J
board_version:
** Loaded modules:
Module Size Used by
i915 254663 1
drm_kms_helper 20033 1 i915
drm 142087 3 i915,drm_kms_helper
i2c_algo_bit 4225 1 i915
binfmt_misc 6399 1
rfcomm 29533 0
l2cap 24720 5 rfcomm
crc16 1319 1 l2cap
bluetooth 41763 4 rfcomm,l2cap
ppdev 5030 0
parport_pc 18855 0
lp 7462 0
parport 27938 3 ppdev,parport_pc,lp
acpi_cpufreq 5523 1
cpufreq_userspace 1960 0
cpufreq_stats 2659 0
cpufreq_conservative 5162 0
cpufreq_powersave 902 0
loop 11767 0
firewire_sbp2 11434 0
snd_hda_codec_idt 42481 1
joydev 8395 0
snd_hda_intel 19955 1
snd_hda_codec 54244 2 snd_hda_codec_idt,snd_hda_intel
arc4 1274 2
snd_hwdep 5380 1 snd_hda_codec
ecb 1841 2
snd_pcm 60503 2 snd_hda_intel,snd_hda_codec
ac 2192 0
iwlagn 73059 0
battery 4998 0
snd_seq 42737 0
snd_timer 15534 2 snd_pcm,snd_seq
snd_seq_device 4493 1 snd_seq
iwlcore 77282 1 iwlagn
mac80211 136188 2 iwlagn,iwlcore
video 17461 1 i915
output 1692 1 video
snd 46414 10 snd_hda_codec_idt,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_seq,snd_timer,snd_seq_device
i2c_i801 7830 0
dcdbas 5000 0
psmouse 49729 0
evdev 7352 15
processor 30191 3 acpi_cpufreq
soundcore 4598 1 snd
pcspkr 1699 0
serio_raw 3752 0
i2c_core 15680 5 i915,drm_kms_helper,drm,i2c_algo_bit,i2c_i801
button 4650 1 i915
cfg80211 100808 3 iwlagn,iwlcore,mac80211
rfkill 12964 2 bluetooth,cfg80211
snd_page_alloc 6169 2 snd_hda_intel,snd_pcm
ext3 106118 1
jbd 36861 1 ext3
mbcache 5050 1 ext3
sg 18712 0
sr_mod 12602 0
cdrom 29415 1 sr_mod
sd_mod 29713 3
crc_t10dif 1276 1 sd_mod
ahci 32310 2
libata 133280 1 ahci
scsi_mod 121845 5 firewire_sbp2,sg,sr_mod,sd_mod,libata
sdhci_pci 5533 0
sdhci 13902 1 sdhci_pci
mmc_core 45040 1 sdhci
led_class 2433 2 iwlcore,sdhci
ehci_hcd 30911 0
uhci_hcd 18457 0
firewire_ohci 19436 0
firewire_core 36672 2 firewire_sbp2,firewire_ohci
crc_itu_t 1307 1 firewire_core
r8169 28669 0
mii 3210 1 r8169
usbcore 121730 3 ehci_hcd,uhci_hcd
nls_base 6377 1 usbcore
thermal 11674 0
fan 3346 0
thermal_sys 11942 4 video,processor,thermal,fan
** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
allow-hotplug eth0
iface eth0 inet dhcp
iface sofa inet dhcp
wireless-essid sofasofa
wireless-key1 **************************
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN qlen 1000
link/ether 00:24:e8:c2:9e:5b brd ff:ff:ff:ff:ff:ff
inet 169.254.8.122/16 brd 169.254.255.255 scope link eth0:avahi
3: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000
link/ether 00:22:fb:ab:b8:54 brd ff:ff:ff:ff:ff:ff
inet 10.0.0.5/8 brd 10.255.255.255 scope global wlan0
inet6 fe80::222:fbff:feab:b854/64 scope link
valid_lft forever preferred_lft forever
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed
lo: 271611 970 0 0 0 0 0 0 271611 970 0 0 0 0 0 0
eth0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
wlan0:231892644 162046 0 0 0 0 0 0 9205406 98072 0 0 0 0 0 0
*** Protocol statistics:
Ip:
163035 total packets received
6 with invalid addresses
0 forwarded
0 incoming packets discarded
163005 incoming packets delivered
98929 requests sent out
Icmp:
99 ICMP messages received
22 input ICMP message failed.
ICMP input histogram:
destination unreachable: 80
timeout in transit: 17
echo replies: 2
100 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
destination unreachable: 80
IcmpMsg:
InType0: 2
InType3: 80
InType11: 17
OutType3: 80
OutType69: 20
Tcp:
799 active connections openings
10 passive connection openings
128 failed connection attempts
6 connection resets received
2 connections established
161685 segments received
97241 segments send out
441 segments retransmited
0 bad segments received.
48 resets sent
Udp:
1161 packets received
40 packets to unknown port received.
0 packet receive errors
1138 packets sent
UdpLite:
TcpExt:
288 TCP sockets finished time wait in fast timer
816 delayed acks sent
Quick ack mode was activated 187 times
123229 packets directly queued to recvmsg prequeue.
74767 bytes directly in process context from backlog
141676795 bytes directly received in process context from prequeue
48270 packet headers predicted
95627 packets header predicted and directly queued to user
1281 acknowledgments not containing data payload received
1138 predicted acknowledgments
32 congestion windows recovered without slow start after partial ack
203 other TCP timeouts
3 times receiver scheduled too late for direct processing
188 DSACKs sent for old packets
12 DSACKs received
1 connections reset due to unexpected data
4 connections reset due to early user close
127 connections aborted due to timeout
TCPDSACKIgnoredOld: 7
TCPDSACKIgnoredNoUndo: 1
IpExt:
InMcastPkts: 142
OutMcastPkts: 149
InBcastPkts: 99
InOctets: 229907730
OutOctets: 6322246
InMcastOctets: 21425
OutMcastOctets: 20921
InBcastOctets: 19764
*** Device features:
eth0: 0x180
lo: 0x13865
wlan0: 0x2000
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub [8086:2a40] (rev 07)
Subsystem: Dell Device [1028:02bc]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller [8086:2a42] (rev 07) (prog-if 00 [VGA controller])
Subsystem: Dell Device [1028:02bc]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 33
Region 0: Memory at f6800000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at 1800 [size=8]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel modules: i915
00:02.1 Display controller [0380]: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller [8086:2a43] (rev 07)
Subsystem: Dell Device [1028:02bc]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at f6100000 (64-bit, non-prefetchable) [size=1M]
Capabilities: <access denied>
00:1a.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 [8086:2937] (rev 03) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:02bc]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at 1820 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 [8086:2938] (rev 03) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:02bc]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at 1840 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.2 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 [8086:2939] (rev 03) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:02bc]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 19
Region 4: I/O ports at 1860 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 [8086:293c] (rev 03) (prog-if 20 [EHCI])
Subsystem: Dell Device [1028:02bc]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 19
Region 0: Memory at f6504800 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1b.0 Audio device [0403]: Intel Corporation 82801I (ICH9 Family) HD Audio Controller [8086:293e] (rev 03)
Subsystem: Dell Device [1028:02bc]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at f6500000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:1c.0 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 [8086:2940] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=03, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: f8000000-f9ffffff
Prefetchable memory behind bridge: 00000000f0000000-00000000f1ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.1 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 [8086:2942] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=08, subordinate=08, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: 80000000-803fffff
Prefetchable memory behind bridge: 00000000f6000000-00000000f60fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.2 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 3 [8086:2944] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0e, subordinate=0f, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: fa000000-fbffffff
Prefetchable memory behind bridge: 00000000f2000000-00000000f3ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.3 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 [8086:2946] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=14, subordinate=15, sec-latency=0
I/O behind bridge: 00005000-00005fff
Memory behind bridge: fc000000-fdffffff
Prefetchable memory behind bridge: 00000000f4000000-00000000f5ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.4 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 [8086:2948] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=1a, subordinate=1a, sec-latency=0
I/O behind bridge: 00006000-00006fff
Memory behind bridge: f6200000-f62fffff
Prefetchable memory behind bridge: 0000000080400000-00000000805fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.5 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 [8086:294a] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=20, subordinate=20, sec-latency=0
I/O behind bridge: 00007000-00007fff
Memory behind bridge: 80600000-807fffff
Prefetchable memory behind bridge: 0000000080800000-00000000809fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1d.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 [8086:2934] (rev 03) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:02bc]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at 1880 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 [8086:2935] (rev 03) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:02bc]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 18a0 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 [8086:2936] (rev 03) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:02bc]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 18c0 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 [8086:293a] (rev 03) (prog-if 20 [EHCI])
Subsystem: Dell Device [1028:02bc]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f6504c00 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev 93) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=26, subordinate=26, sec-latency=0
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation ICH9M LPC Interface Controller [8086:2919] (rev 03)
Subsystem: Dell Device [1028:02bc]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel modules: iTCO_wdt
00:1f.2 SATA controller [0106]: Intel Corporation ICH9M/M-E SATA AHCI Controller [8086:2929] (rev 03) (prog-if 01 [AHCI 1.0])
Subsystem: Dell Device [1028:02bc]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 31
Region 0: I/O ports at 1818 [size=8]
Region 1: I/O ports at 180c [size=4]
Region 2: I/O ports at 1810 [size=8]
Region 3: I/O ports at 1808 [size=4]
Region 4: I/O ports at 18e0 [size=32]
Region 5: Memory at f6504000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
Kernel modules: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 82801I (ICH9 Family) SMBus Controller [8086:2930] (rev 03)
Subsystem: Dell Device [1028:02bc]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 19
Region 0: Memory at 80a00000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 1c00 [size=32]
Kernel modules: i2c-i801
08:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 03)
Subsystem: Dell Device [1028:02bc]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 30
Region 0: I/O ports at 3000 [size=256]
Region 2: Memory at f6004000 (64-bit, prefetchable) [size=4K]
Region 4: Memory at f6000000 (64-bit, prefetchable) [size=16K]
[virtual] Expansion ROM at f6020000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: r8169
Kernel modules: r8169
0e:00.0 Network controller [0280]: Intel Corporation Wireless WiFi Link 5100 [8086:4232]
Subsystem: Intel Corporation Wireless WiFi Link 5100 [8086:1321]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 32
Region 0: Memory at fa000000 (64-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: iwlagn
Kernel modules: iwlagn
1a:00.0 FireWire (IEEE 1394) [0c00]: O2 Micro, Inc. Device [1217:10f7] (rev 01) (prog-if 10 [OHCI])
Subsystem: Dell Device [1028:02bc]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f6200000 (32-bit, non-prefetchable) [size=4K]
Region 1: Memory at f6202000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
Kernel modules: firewire-ohci
1a:00.1 SD Host controller [0805]: O2 Micro, Inc. Device [1217:8120] (rev 01)
Subsystem: Dell Device [1028:02bc]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f6203800 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: sdhci-pci
Kernel modules: sdhci-pci
1a:00.2 Mass storage controller [0180]: O2 Micro, Inc. Device [1217:8130] (rev 01)
Subsystem: Dell Device [1028:02bc]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f6201000 (32-bit, non-prefetchable) [size=4K]
Region 1: Memory at f6203000 (32-bit, non-prefetchable) [size=2K]
Region 2: Memory at f6202800 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
** USB devices:
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
-- System Information:
Debian Release: 5.0.6
APT prefers stable
APT policy: (540, 'stable')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.32-bpo.5-amd64 (SMP w/2 CPU cores)
Locale: LANG=en_GB.UTF-8, LC_CTYPE=en_GB.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.32-bpo.5-amd64 depends on:
ii debconf [debconf-2.0] 1.5.24 Debian configuration management sy
ii initramfs-tools [linux 0.92o tools for generating an initramfs
ii linux-base 2.6.32-23~bpo50+1 Linux image base package
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.32-bpo.5-amd64 recommends:
ii firmware-linux-free 2.6.32-23~bpo50+1 Binary firmware for various driver
Versions of packages linux-image-2.6.32-bpo.5-amd64 suggests:
ii grub-pc [grub] 1.96+20080724-16 GRand Unified Bootloader, version
pn linux-doc-2.6.32 <none> (no description available)
Versions of packages linux-image-2.6.32-bpo.5-amd64 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
ii firmware-iwlwifi 0.17~bpo50+1 Binary firmware for Intel Wireless
pn firmware-linux <none> (no description available)
pn firmware-linux-nonfree <none> (no description available)
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn xen-hypervisor <none> (no description available)
-- debconf information:
linux-image-2.6.32-bpo.5-amd64/prerm/removing-running-kernel-2.6.32-bpo.5-amd64: true
* linux-image-2.6.32-bpo.5-amd64/postinst/missing-firmware-2.6.32-bpo.5-amd64:
linux-image-2.6.32-bpo.5-amd64/postinst/depmod-error-initrd-2.6.32-bpo.5-amd64: false
linux-image-2.6.32-bpo.5-amd64/postinst/ignoring-do-bootloader-2.6.32-bpo.5-amd64:
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.32-bpo.5-amd64 (Debian 2.6.32-23~bpo50+1) (norbert@tretkowski.de) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) #1 SMP Sat Sep 18 19:03:14 UTC 2010
[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-bpo.5-amd64 root=UUID=b25673dd-6844-4fc6-8c4d-90f5d52e0b9d ro quiet
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] Centaur CentaurHauls
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
[ 0.000000] BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000d2000 - 00000000000d4000 (reserved)
[ 0.000000] BIOS-e820: 00000000000d8000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007d6a1000 (usable)
[ 0.000000] BIOS-e820: 000000007d6a1000 - 000000007d6a7000 (reserved)
[ 0.000000] BIOS-e820: 000000007d6a7000 - 000000007d7bd000 (usable)
[ 0.000000] BIOS-e820: 000000007d7bd000 - 000000007d80f000 (reserved)
[ 0.000000] BIOS-e820: 000000007d80f000 - 000000007d908000 (usable)
[ 0.000000] BIOS-e820: 000000007d908000 - 000000007db0f000 (reserved)
[ 0.000000] BIOS-e820: 000000007db0f000 - 000000007db18000 (usable)
[ 0.000000] BIOS-e820: 000000007db18000 - 000000007db1f000 (reserved)
[ 0.000000] BIOS-e820: 000000007db1f000 - 000000007db64000 (usable)
[ 0.000000] BIOS-e820: 000000007db64000 - 000000007db9f000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007db9f000 - 000000007dbe6000 (usable)
[ 0.000000] BIOS-e820: 000000007dbe6000 - 000000007dbff000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007dbff000 - 000000007dc00000 (usable)
[ 0.000000] BIOS-e820: 000000007dc00000 - 000000007de00000 (reserved)
[ 0.000000] BIOS-e820: 000000007e000000 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
[ 0.000000] BIOS-e820: 00000000fed10000 - 00000000fed14000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed18000 - 00000000fed1a000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
[ 0.000000] DMI present.
[ 0.000000] last_pfn = 0x7dc00 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 07E000000 mask FFE000000 uncachable
[ 0.000000] 1 base 000000000 mask F80000000 write-back
[ 0.000000] 2 base 0FFE40000 mask FFFFC0000 write-protect
[ 0.000000] 3 base 07DE00000 mask FFFE00000 uncachable
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] initial memory mapped : 0 - 20000000
[ 0.000000] init_memory_mapping: 0000000000000000-000000007dc00000
[ 0.000000] 0000000000 - 007dc00000 page 2M
[ 0.000000] kernel direct mapping tables up to 7dc00000 @ 8000-b000
[ 0.000000] RAMDISK: 378a0000 - 37fef627
[ 0.000000] ACPI: RSDP 00000000000f6a40 00024 (v02 DELL )
[ 0.000000] ACPI: XSDT 000000007dbf874d 0006C (v01 DELL CL09 06040000 LTP 00000000)
[ 0.000000] ACPI: FACP 000000007dbe8000 000F4 (v03 TOSCPL CRESTLNE 06040000 ALAN 00000001)
[ 0.000000] ACPI: DSDT 000000007dbe9000 06318 (v02 Intel CANTIGA 06040000 INTL 20060608)
[ 0.000000] ACPI: FACS 000000007db9efc0 00040
[ 0.000000] ACPI: HPET 000000007dbfed14 00038 (v01 INTEL CRESTLNE 06040000 LOHR 0000005A)
[ 0.000000] ACPI: MCFG 000000007dbfed4c 0003C (v01 INTEL CRESTLNE 06040000 LOHR 0000005A)
[ 0.000000] ACPI: OSFR 000000007dbfed88 00072 (v01 TOSHIB A+2nd ID 06040000 TASM 04010000)
[ 0.000000] ACPI: APIC 000000007dbfedfa 00068 (v01 PTLTD ? APIC 06040000 LTP 00000000)
[ 0.000000] ACPI: BOOT 000000007dbfee62 00028 (v01 PTLTD $SBFTBL$ 06040000 LTP 00000001)
[ 0.000000] ACPI: SLIC 000000007dbfee8a 00176 (v01 DELL CL09 06040000 LTP 00000000)
[ 0.000000] ACPI: SSDT 000000007dbf87f1 000A3 (v01 BrtRef DD01BRT 00001000 INTL 20050624)
[ 0.000000] ACPI: SSDT 000000007dbe7000 00655 (v01 PmRef CpuPm 00003000 INTL 20050624)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at 0000000000000000-000000007dc00000
[ 0.000000] Bootmem setup node 0 0000000000000000-000000007dc00000
[ 0.000000] NODE_DATA [0000000000009000 - 0000000000010fff]
[ 0.000000] bootmap [0000000000011000 - 0000000000020b7f] pages 10
[ 0.000000] (7 early reservations) ==> bootmem [0000000000 - 007dc00000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
[ 0.000000] #2 [0001000000 - 0001684414] TEXT DATA BSS ==> [0001000000 - 0001684414]
[ 0.000000] #3 [00378a0000 - 0037fef627] RAMDISK ==> [00378a0000 - 0037fef627]
[ 0.000000] #4 [000009f400 - 0000100000] BIOS reserved ==> [000009f400 - 0000100000]
[ 0.000000] #5 [0001685000 - 000168512c] BRK ==> [0001685000 - 000168512c]
[ 0.000000] #6 [0000008000 - 0000009000] PGTABLE ==> [0000008000 - 0000009000]
[ 0.000000] found SMP MP-table at [ffff8800000f6b20] f6b20
[ 0.000000] [ffffea0000000000-ffffea0001bfffff] PMD -> [ffff880001c00000-ffff8800037fffff] on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal 0x00100000 -> 0x00100000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[8] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0007d6a1
[ 0.000000] 0: 0x0007d6a7 -> 0x0007d7bd
[ 0.000000] 0: 0x0007d80f -> 0x0007d908
[ 0.000000] 0: 0x0007db0f -> 0x0007db18
[ 0.000000] 0: 0x0007db1f -> 0x0007db64
[ 0.000000] 0: 0x0007db9f -> 0x0007dbe6
[ 0.000000] 0: 0x0007dbff -> 0x0007dc00
[ 0.000000] On node 0 totalpages: 514277
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 100 pages reserved
[ 0.000000] DMA zone: 3843 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 6986 pages used for memmap
[ 0.000000] DMA32 zone: 503292 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 24
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000d2000
[ 0.000000] PM: Registered nosave memory: 00000000000d2000 - 00000000000d4000
[ 0.000000] PM: Registered nosave memory: 00000000000d4000 - 00000000000d8000
[ 0.000000] PM: Registered nosave memory: 00000000000d8000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 000000007d6a1000 - 000000007d6a7000
[ 0.000000] PM: Registered nosave memory: 000000007d7bd000 - 000000007d80f000
[ 0.000000] PM: Registered nosave memory: 000000007d908000 - 000000007db0f000
[ 0.000000] PM: Registered nosave memory: 000000007db18000 - 000000007db1f000
[ 0.000000] PM: Registered nosave memory: 000000007db64000 - 000000007db9f000
[ 0.000000] PM: Registered nosave memory: 000000007dbe6000 - 000000007dbff000
[ 0.000000] Allocating PCI resources starting at 80000000 (gap: 80000000:60000000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:2 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 30 pages/cpu @ffff880001800000 s90328 r8192 d24360 u1048576
[ 0.000000] pcpu-alloc: s90328 r8192 d24360 u1048576 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 507135
[ 0.000000] Policy zone: DMA32
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-bpo.5-amd64 root=UUID=b25673dd-6844-4fc6-8c4d-90f5d52e0b9d ro quiet
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] xsave/xrstor: enabled xstate_bv 0x3, cntxt size 0x240
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 2013696k/2060288k available (3075k kernel code, 3180k absent, 43412k reserved, 1879k data, 584k init)
[ 0.000000] SLUB: Genslabs=14, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:4352 nr_irqs:424
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] hpet clockevent registered
[ 0.000000] HPET: 4 timers in total, 0 timers will be used for per-cpu timer
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 2194.667 MHz processor.
[ 0.004006] Calibrating delay loop (skipped), value calculated using timer frequency.. 4389.33 BogoMIPS (lpj=8778668)
[ 0.004023] Security Framework initialized
[ 0.004029] SELinux: Disabled at boot.
[ 0.004188] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.005399] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.008140] Mount-cache hash table entries: 256
[ 0.008284] Initializing cgroup subsys ns
[ 0.008287] Initializing cgroup subsys cpuacct
[ 0.008291] Initializing cgroup subsys devices
[ 0.008293] Initializing cgroup subsys freezer
[ 0.008295] Initializing cgroup subsys net_cls
[ 0.008320] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.008321] CPU: L2 cache: 2048K
[ 0.008325] CPU 0/0x0 -> Node 0
[ 0.008327] CPU: Physical Processor ID: 0
[ 0.008328] CPU: Processor Core ID: 0
[ 0.008331] mce: CPU supports 6 MCE banks
[ 0.008339] CPU0: Thermal monitoring enabled (TM2)
[ 0.008343] using mwait in idle threads.
[ 0.008345] Performance Events: Core2 events, Intel PMU driver.
[ 0.008350] ... version: 2
[ 0.008352] ... bit width: 40
[ 0.008353] ... generic registers: 2
[ 0.008354] ... value mask: 000000ffffffffff
[ 0.008356] ... max period: 000000007fffffff
[ 0.008357] ... fixed-purpose events: 3
[ 0.008359] ... event mask: 0000000700000003
[ 0.009366] ACPI: Core revision 20090903
[ 0.020071] Setting APIC routing to flat
[ 0.020657] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.061302] CPU0: Intel(R) Core(TM)2 Duo CPU T6670 @ 2.20GHz stepping 0a
[ 0.064001] Booting processor 1 APIC 0x1 ip 0x6000
[ 0.008000] Initializing CPU#1
[ 0.008000] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.008000] CPU: L2 cache: 2048K
[ 0.008000] CPU 1/0x1 -> Node 0
[ 0.008000] CPU: Physical Processor ID: 0
[ 0.008000] CPU: Processor Core ID: 1
[ 0.008000] CPU1: Thermal monitoring enabled (TM2)
[ 0.148040] CPU1: Intel(R) Core(TM)2 Duo CPU T6670 @ 2.20GHz stepping 0a
[ 0.148047] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.152017] Brought up 2 CPUs
[ 0.152019] Total of 2 processors activated (8778.28 BogoMIPS).
[ 0.152482] CPU0 attaching sched-domain:
[ 0.152485] domain 0: span 0-1 level MC
[ 0.152487] groups: 0 1
[ 0.152493] CPU1 attaching sched-domain:
[ 0.152495] domain 0: span 0-1 level MC
[ 0.152497] groups: 1 0
[ 0.152573] devtmpfs: initialized
[ 0.154841] regulator: core version 0.5
[ 0.154841] NET: Registered protocol family 16
[ 0.154841] ACPI: bus type pci registered
[ 0.154841] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.154841] PCI: MCFG area at e0000000 reserved in E820
[ 0.169006] PCI: Using MMCONFIG at e0000000 - efffffff
[ 0.169007] PCI: Using configuration type 1 for base access
[ 0.169315] bio: create slab <bio-0> at 0
[ 0.169315] ACPI: EC: Look up EC in DSDT
[ 0.173078] ACPI: BIOS _OSI(Linux) query ignored
[ 0.178176] ACPI: Interpreter enabled
[ 0.178178] ACPI: (supports S0 S3 S4 S5)
[ 0.178199] ACPI: Using IOAPIC for interrupt routing
[ 0.334128] ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62
[ 0.334516] ACPI: No dock devices found.
[ 0.335134] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.335188] DMAR: Forcing write-buffer flush capability
[ 0.335221] pci 0000:00:02.0: reg 10 64bit mmio: [0xf6800000-0xf6bfffff]
[ 0.335227] pci 0000:00:02.0: reg 18 64bit mmio pref: [0xd0000000-0xdfffffff]
[ 0.335232] pci 0000:00:02.0: reg 20 io port: [0x1800-0x1807]
[ 0.335268] pci 0000:00:02.1: reg 10 64bit mmio: [0xf6100000-0xf61fffff]
[ 0.335388] pci 0000:00:1a.0: reg 20 io port: [0x1820-0x183f]
[ 0.335480] pci 0000:00:1a.1: reg 20 io port: [0x1840-0x185f]
[ 0.335572] pci 0000:00:1a.2: reg 20 io port: [0x1860-0x187f]
[ 0.336034] pci 0000:00:1a.7: reg 10 32bit mmio: [0xf6504800-0xf6504bff]
[ 0.336101] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
[ 0.336106] pci 0000:00:1a.7: PME# disabled
[ 0.336163] pci 0000:00:1b.0: reg 10 64bit mmio: [0xf6500000-0xf6503fff]
[ 0.336222] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.336227] pci 0000:00:1b.0: PME# disabled
[ 0.336321] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.336325] pci 0000:00:1c.0: PME# disabled
[ 0.336420] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 0.336425] pci 0000:00:1c.1: PME# disabled
[ 0.336519] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[ 0.336524] pci 0000:00:1c.2: PME# disabled
[ 0.336618] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[ 0.336622] pci 0000:00:1c.3: PME# disabled
[ 0.336717] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[ 0.336722] pci 0000:00:1c.4: PME# disabled
[ 0.336815] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
[ 0.336820] pci 0000:00:1c.5: PME# disabled
[ 0.336895] pci 0000:00:1d.0: reg 20 io port: [0x1880-0x189f]
[ 0.336988] pci 0000:00:1d.1: reg 20 io port: [0x18a0-0x18bf]
[ 0.337082] pci 0000:00:1d.2: reg 20 io port: [0x18c0-0x18df]
[ 0.337175] pci 0000:00:1d.7: reg 10 32bit mmio: [0xf6504c00-0xf6504fff]
[ 0.337242] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.337247] pci 0000:00:1d.7: PME# disabled
[ 0.337506] pci 0000:00:1f.2: reg 10 io port: [0x1818-0x181f]
[ 0.337514] pci 0000:00:1f.2: reg 14 io port: [0x180c-0x180f]
[ 0.337521] pci 0000:00:1f.2: reg 18 io port: [0x1810-0x1817]
[ 0.337529] pci 0000:00:1f.2: reg 1c io port: [0x1808-0x180b]
[ 0.337536] pci 0000:00:1f.2: reg 20 io port: [0x18e0-0x18ff]
[ 0.337544] pci 0000:00:1f.2: reg 24 32bit mmio: [0xf6504000-0xf65047ff]
[ 0.337591] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.337595] pci 0000:00:1f.2: PME# disabled
[ 0.337637] pci 0000:00:1f.3: reg 10 64bit mmio: [0x000000-0x0000ff]
[ 0.337655] pci 0000:00:1f.3: reg 20 io port: [0x1c00-0x1c1f]
[ 0.337741] pci 0000:00:1c.0: bridge io port: [0x2000-0x2fff]
[ 0.337745] pci 0000:00:1c.0: bridge 32bit mmio: [0xf8000000-0xf9ffffff]
[ 0.337753] pci 0000:00:1c.0: bridge 64bit mmio pref: [0xf0000000-0xf1ffffff]
[ 0.337815] pci 0000:08:00.0: reg 10 io port: [0x3000-0x30ff]
[ 0.337842] pci 0000:08:00.0: reg 18 64bit mmio pref: [0xf6004000-0xf6004fff]
[ 0.337860] pci 0000:08:00.0: reg 20 64bit mmio pref: [0xf6000000-0xf6003fff]
[ 0.337870] pci 0000:08:00.0: reg 30 32bit mmio pref: [0x000000-0x01ffff]
[ 0.337923] pci 0000:08:00.0: supports D1 D2
[ 0.337925] pci 0000:08:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.337931] pci 0000:08:00.0: PME# disabled
[ 0.344115] pci 0000:00:1c.1: bridge io port: [0x3000-0x3fff]
[ 0.344126] pci 0000:00:1c.1: bridge 64bit mmio pref: [0xf6000000-0xf60fffff]
[ 0.344266] pci 0000:0e:00.0: reg 10 64bit mmio: [0xfa000000-0xfa001fff]
[ 0.344391] pci 0000:0e:00.0: PME# supported from D0 D3hot D3cold
[ 0.344403] pci 0000:0e:00.0: PME# disabled
[ 0.352154] pci 0000:00:1c.2: bridge io port: [0x4000-0x4fff]
[ 0.352159] pci 0000:00:1c.2: bridge 32bit mmio: [0xfa000000-0xfbffffff]
[ 0.352167] pci 0000:00:1c.2: bridge 64bit mmio pref: [0xf2000000-0xf3ffffff]
[ 0.352226] pci 0000:00:1c.3: bridge io port: [0x5000-0x5fff]
[ 0.352230] pci 0000:00:1c.3: bridge 32bit mmio: [0xfc000000-0xfdffffff]
[ 0.352238] pci 0000:00:1c.3: bridge 64bit mmio pref: [0xf4000000-0xf5ffffff]
[ 0.352366] pci 0000:1a:00.0: reg 10 32bit mmio: [0xf6200000-0xf6200fff]
[ 0.352389] pci 0000:1a:00.0: reg 14 32bit mmio: [0xf6202000-0xf62027ff]
[ 0.352588] pci 0000:1a:00.0: supports D1 D2
[ 0.352590] pci 0000:1a:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.352602] pci 0000:1a:00.0: PME# disabled
[ 0.352764] pci 0000:1a:00.1: reg 10 32bit mmio: [0xf6203800-0xf62038ff]
[ 0.352984] pci 0000:1a:00.1: supports D1 D2
[ 0.352986] pci 0000:1a:00.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.352999] pci 0000:1a:00.1: PME# disabled
[ 0.353152] pci 0000:1a:00.2: reg 10 32bit mmio: [0xf6201000-0xf6201fff]
[ 0.353176] pci 0000:1a:00.2: reg 14 32bit mmio: [0xf6203000-0xf62037ff]
[ 0.353199] pci 0000:1a:00.2: reg 18 32bit mmio: [0xf6202800-0xf6202fff]
[ 0.353377] pci 0000:1a:00.2: supports D1 D2
[ 0.353379] pci 0000:1a:00.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.353391] pci 0000:1a:00.2: PME# disabled
[ 0.354009] pci 0000:00:1c.4: bridge 32bit mmio: [0xf6200000-0xf62fffff]
[ 0.354146] pci 0000:00:1e.0: transparent bridge
[ 0.354203] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.354343] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[ 0.354435] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[ 0.354499] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
[ 0.354564] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
[ 0.354628] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP04._PRT]
[ 0.354691] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP05._PRT]
[ 0.354756] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP06._PRT]
[ 0.369095] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[ 0.369196] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[ 0.369294] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 *5 6 7 10 12 14 15)
[ 0.369392] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 *5 6 7 11 12 14 15)
[ 0.369491] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
[ 0.369589] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 *7 11 12 14 15)
[ 0.369688] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 *5 6 7 10 12 14 15)
[ 0.369785] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[ 0.369872] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.369887] vgaarb: loaded
[ 0.369916] PCI: Using ACPI for IRQ routing
[ 0.369916] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[ 0.369916] hpet0: 4 comparators, 64-bit 14.318180 MHz counter
[ 0.380019] Switching to clocksource tsc
[ 0.381143] pnp: PnP ACPI init
[ 0.381151] ACPI: bus type pnp registered
[ 0.452440] pnp 00:08: mem resource (0xf6203900-0xf6203bff) overlaps 0000:00:1c.4 BAR 14 (0xf6200000-0xf62fffff), disabling
[ 0.453059] pnp: PnP ACPI: found 10 devices
[ 0.453061] ACPI: ACPI bus type pnp unregistered
[ 0.453070] system 00:02: iomem range 0xfed00000-0xfed003ff has been reserved
[ 0.453076] system 00:04: ioport range 0x480-0x48f has been reserved
[ 0.453078] system 00:04: ioport range 0xffff-0xffff has been reserved
[ 0.453081] system 00:04: ioport range 0xffff-0xffff has been reserved
[ 0.453084] system 00:04: ioport range 0x400-0x47f has been reserved
[ 0.453086] system 00:04: ioport range 0x1180-0x11ff has been reserved
[ 0.453089] system 00:04: ioport range 0xfe00-0xfe00 has been reserved
[ 0.453092] system 00:04: ioport range 0xff2c-0xff7f has been reserved
[ 0.453100] system 00:09: iomem range 0xfed1c000-0xfed1ffff has been reserved
[ 0.453103] system 00:09: iomem range 0xfed10000-0xfed13fff has been reserved
[ 0.453106] system 00:09: iomem range 0xfed18000-0xfed18fff has been reserved
[ 0.453108] system 00:09: iomem range 0xfed19000-0xfed19fff has been reserved
[ 0.453111] system 00:09: iomem range 0xe0000000-0xefffffff has been reserved
[ 0.453114] system 00:09: iomem range 0xfed20000-0xfed3ffff has been reserved
[ 0.453117] system 00:09: iomem range 0xfed40000-0xfed44fff has been reserved
[ 0.453119] system 00:09: iomem range 0xfed45000-0xfed8ffff has been reserved
[ 0.457872] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
[ 0.457875] pci 0000:00:1c.0: IO window: 0x2000-0x2fff
[ 0.457882] pci 0000:00:1c.0: MEM window: 0xf8000000-0xf9ffffff
[ 0.457887] pci 0000:00:1c.0: PREFETCH window: 0x000000f0000000-0x000000f1ffffff
[ 0.457895] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:08
[ 0.457898] pci 0000:00:1c.1: IO window: 0x3000-0x3fff
[ 0.457904] pci 0000:00:1c.1: MEM window: 0x80000000-0x803fffff
[ 0.457909] pci 0000:00:1c.1: PREFETCH window: 0x000000f6000000-0x000000f60fffff
[ 0.457917] pci 0000:00:1c.2: PCI bridge, secondary bus 0000:0e
[ 0.457920] pci 0000:00:1c.2: IO window: 0x4000-0x4fff
[ 0.457926] pci 0000:00:1c.2: MEM window: 0xfa000000-0xfbffffff
[ 0.457931] pci 0000:00:1c.2: PREFETCH window: 0x000000f2000000-0x000000f3ffffff
[ 0.457939] pci 0000:00:1c.3: PCI bridge, secondary bus 0000:14
[ 0.457942] pci 0000:00:1c.3: IO window: 0x5000-0x5fff
[ 0.457948] pci 0000:00:1c.3: MEM window: 0xfc000000-0xfdffffff
[ 0.457953] pci 0000:00:1c.3: PREFETCH window: 0x000000f4000000-0x000000f5ffffff
[ 0.457961] pci 0000:00:1c.4: PCI bridge, secondary bus 0000:1a
[ 0.457964] pci 0000:00:1c.4: IO window: 0x6000-0x6fff
[ 0.457970] pci 0000:00:1c.4: MEM window: 0xf6200000-0xf62fffff
[ 0.457975] pci 0000:00:1c.4: PREFETCH window: 0x00000080400000-0x000000805fffff
[ 0.457982] pci 0000:00:1c.5: PCI bridge, secondary bus 0000:20
[ 0.457985] pci 0000:00:1c.5: IO window: 0x7000-0x7fff
[ 0.457991] pci 0000:00:1c.5: MEM window: 0x80600000-0x807fffff
[ 0.457996] pci 0000:00:1c.5: PREFETCH window: 0x00000080800000-0x000000809fffff
[ 0.458004] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:26
[ 0.458005] pci 0000:00:1e.0: IO window: disabled
[ 0.458011] pci 0000:00:1e.0: MEM window: disabled
[ 0.458015] pci 0000:00:1e.0: PREFETCH window: disabled
[ 0.458032] alloc irq_desc for 17 on node -1
[ 0.458034] alloc kstat_irqs on node -1
[ 0.458038] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.458044] pci 0000:00:1c.0: setting latency timer to 64
[ 0.458054] alloc irq_desc for 16 on node -1
[ 0.458055] alloc kstat_irqs on node -1
[ 0.458059] pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16
[ 0.458063] pci 0000:00:1c.1: setting latency timer to 64
[ 0.458073] alloc irq_desc for 18 on node -1
[ 0.458074] alloc kstat_irqs on node -1
[ 0.458078] pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.458082] pci 0000:00:1c.2: setting latency timer to 64
[ 0.458091] alloc irq_desc for 19 on node -1
[ 0.458093] alloc kstat_irqs on node -1
[ 0.458096] pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 0.458101] pci 0000:00:1c.3: setting latency timer to 64
[ 0.458110] pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.458115] pci 0000:00:1c.4: setting latency timer to 64
[ 0.458125] pci 0000:00:1c.5: PCI INT B -> GSI 16 (level, low) -> IRQ 16
[ 0.458130] pci 0000:00:1c.5: setting latency timer to 64
[ 0.458138] pci 0000:00:1e.0: setting latency timer to 64
[ 0.458142] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.458144] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
[ 0.458147] pci_bus 0000:02: resource 0 io: [0x2000-0x2fff]
[ 0.458149] pci_bus 0000:02: resource 1 mem: [0xf8000000-0xf9ffffff]
[ 0.458151] pci_bus 0000:02: resource 2 pref mem [0xf0000000-0xf1ffffff]
[ 0.458153] pci_bus 0000:08: resource 0 io: [0x3000-0x3fff]
[ 0.458155] pci_bus 0000:08: resource 1 mem: [0x80000000-0x803fffff]
[ 0.458158] pci_bus 0000:08: resource 2 pref mem [0xf6000000-0xf60fffff]
[ 0.458160] pci_bus 0000:0e: resource 0 io: [0x4000-0x4fff]
[ 0.458162] pci_bus 0000:0e: resource 1 mem: [0xfa000000-0xfbffffff]
[ 0.458164] pci_bus 0000:0e: resource 2 pref mem [0xf2000000-0xf3ffffff]
[ 0.458166] pci_bus 0000:14: resource 0 io: [0x5000-0x5fff]
[ 0.458168] pci_bus 0000:14: resource 1 mem: [0xfc000000-0xfdffffff]
[ 0.458171] pci_bus 0000:14: resource 2 pref mem [0xf4000000-0xf5ffffff]
[ 0.458173] pci_bus 0000:1a: resource 0 io: [0x6000-0x6fff]
[ 0.458175] pci_bus 0000:1a: resource 1 mem: [0xf6200000-0xf62fffff]
[ 0.458177] pci_bus 0000:1a: resource 2 pref mem [0x80400000-0x805fffff]
[ 0.458179] pci_bus 0000:20: resource 0 io: [0x7000-0x7fff]
[ 0.458181] pci_bus 0000:20: resource 1 mem: [0x80600000-0x807fffff]
[ 0.458183] pci_bus 0000:20: resource 2 pref mem [0x80800000-0x809fffff]
[ 0.458186] pci_bus 0000:26: resource 3 io: [0x00-0xffff]
[ 0.458188] pci_bus 0000:26: resource 4 mem: [0x000000-0xffffffffffffffff]
[ 0.458217] NET: Registered protocol family 2
[ 0.458328] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.459031] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 0.461490] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.462191] TCP: Hash tables configured (established 262144 bind 65536)
[ 0.462193] TCP reno registered
[ 0.462310] NET: Registered protocol family 1
[ 0.462332] pci 0000:00:02.0: Boot video device
[ 0.462546] Unpacking initramfs...
[ 0.655036] Freeing initrd memory: 7485k freed
[ 0.659207] Simple Boot Flag at 0x36 set to 0x1
[ 0.659546] audit: initializing netlink socket (disabled)
[ 0.659561] type=2000 audit(1285104635.655:1): initialized
[ 0.662371] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.663649] VFS: Disk quotas dquot_6.5.2
[ 0.663697] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.663767] msgmni has been set to 3947
[ 0.663989] alg: No test for stdrng (krng)
[ 0.664031] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.664034] io scheduler noop registered
[ 0.664035] io scheduler anticipatory registered
[ 0.664037] io scheduler deadline registered
[ 0.664066] io scheduler cfq registered (default)
[ 0.664209] alloc irq_desc for 24 on node -1
[ 0.664211] alloc kstat_irqs on node -1
[ 0.664224] pcieport 0000:00:1c.0: irq 24 for MSI/MSI-X
[ 0.664235] pcieport 0000:00:1c.0: setting latency timer to 64
[ 0.664384] alloc irq_desc for 25 on node -1
[ 0.664386] alloc kstat_irqs on node -1
[ 0.664394] pcieport 0000:00:1c.1: irq 25 for MSI/MSI-X
[ 0.664404] pcieport 0000:00:1c.1: setting latency timer to 64
[ 0.664548] alloc irq_desc for 26 on node -1
[ 0.664550] alloc kstat_irqs on node -1
[ 0.664558] pcieport 0000:00:1c.2: irq 26 for MSI/MSI-X
[ 0.664568] pcieport 0000:00:1c.2: setting latency timer to 64
[ 0.664712] alloc irq_desc for 27 on node -1
[ 0.664714] alloc kstat_irqs on node -1
[ 0.664722] pcieport 0000:00:1c.3: irq 27 for MSI/MSI-X
[ 0.664732] pcieport 0000:00:1c.3: setting latency timer to 64
[ 0.664881] alloc irq_desc for 28 on node -1
[ 0.664883] alloc kstat_irqs on node -1
[ 0.664891] pcieport 0000:00:1c.4: irq 28 for MSI/MSI-X
[ 0.664902] pcieport 0000:00:1c.4: setting latency timer to 64
[ 0.665049] alloc irq_desc for 29 on node -1
[ 0.665050] alloc kstat_irqs on node -1
[ 0.665059] pcieport 0000:00:1c.5: irq 29 for MSI/MSI-X
[ 0.665069] pcieport 0000:00:1c.5: setting latency timer to 64
[ 0.666488] Linux agpgart interface v0.103
[ 0.666502] agpgart-intel 0000:00:00.0: Intel Mobile Intel® GM45 Express Chipset
[ 0.667239] agpgart-intel 0000:00:00.0: detected 32764K stolen memory
[ 0.693773] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
[ 0.693820] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.694169] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 0.694228] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 0.729220] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.729227] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.729298] mice: PS/2 mouse device common for all mice
[ 0.729334] rtc_cmos 00:05: RTC can wake from S4
[ 0.729367] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[ 0.729401] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[ 0.729412] cpuidle: using governor ladder
[ 0.729414] cpuidle: using governor menu
[ 0.729418] No iBFT detected.
[ 0.729698] TCP cubic registered
[ 0.729792] NET: Registered protocol family 10
[ 0.730176] lo: Disabled Privacy Extensions
[ 0.730420] Mobile IPv6
[ 0.730423] NET: Registered protocol family 17
[ 0.730493] PM: Resume from disk failed.
[ 0.730503] registered taskstats version 1
[ 0.732251] rtc_cmos 00:05: setting system clock to 2010-09-21 21:30:36 UTC (1285104636)
[ 0.732317] Initalizing network drop monitor service
[ 0.732338] Freeing unused kernel memory: 584k freed
[ 0.732488] Write protecting the kernel read-only data: 4216k
[ 0.754983] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[ 1.049116] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 1.049143] r8169 0000:08:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 1.049189] r8169 0000:08:00.0: setting latency timer to 64
[ 1.049244] alloc irq_desc for 30 on node -1
[ 1.049246] alloc kstat_irqs on node -1
[ 1.049262] r8169 0000:08:00.0: irq 30 for MSI/MSI-X
[ 1.049765] eth0: RTL8168d/8111d at 0xffffc9000037a000, 00:24:e8:c2:9e:5b, XID 081000c0 IRQ 30
[ 1.060537] usbcore: registered new interface driver usbfs
[ 1.060565] usbcore: registered new interface driver hub
[ 1.085053] usbcore: registered new device driver usb
[ 1.089042] r8169 0000:08:00.0: firmware: requesting rtl8168d-1.fw
[ 1.113337] firewire_ohci 0000:1a:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.113352] firewire_ohci 0000:1a:00.0: setting latency timer to 64
[ 1.115326] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.115366] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.115375] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 1.115379] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 1.115406] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 1.115451] uhci_hcd 0000:00:1a.0: irq 16, io base 0x00001820
[ 1.115490] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.115493] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.115495] usb usb1: Product: UHCI Host Controller
[ 1.115497] usb usb1: Manufacturer: Linux 2.6.32-bpo.5-amd64 uhci_hcd
[ 1.115499] usb usb1: SerialNumber: 0000:00:1a.0
[ 1.115568] usb usb1: configuration #1 chosen from 1 choice
[ 1.115597] hub 1-0:1.0: USB hub found
[ 1.115603] hub 1-0:1.0: 2 ports detected
[ 1.115653] alloc irq_desc for 21 on node -1
[ 1.115655] alloc kstat_irqs on node -1
[ 1.115660] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 1.115667] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[ 1.115670] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 1.115677] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
[ 1.115711] uhci_hcd 0000:00:1a.1: irq 21, io base 0x00001840
[ 1.115742] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.115745] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.115747] usb usb2: Product: UHCI Host Controller
[ 1.115748] usb usb2: Manufacturer: Linux 2.6.32-bpo.5-amd64 uhci_hcd
[ 1.115750] usb usb2: SerialNumber: 0000:00:1a.1
[ 1.115796] usb usb2: configuration #1 chosen from 1 choice
[ 1.115822] hub 2-0:1.0: USB hub found
[ 1.115827] hub 2-0:1.0: 2 ports detected
[ 1.115870] uhci_hcd 0000:00:1a.2: PCI INT C -> GSI 19 (level, low) -> IRQ 19
[ 1.115876] uhci_hcd 0000:00:1a.2: setting latency timer to 64
[ 1.115880] uhci_hcd 0000:00:1a.2: UHCI Host Controller
[ 1.115888] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 3
[ 1.115923] uhci_hcd 0000:00:1a.2: irq 19, io base 0x00001860
[ 1.115954] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.115956] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.115958] usb usb3: Product: UHCI Host Controller
[ 1.115960] usb usb3: Manufacturer: Linux 2.6.32-bpo.5-amd64 uhci_hcd
[ 1.115962] usb usb3: SerialNumber: 0000:00:1a.2
[ 1.117588] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.117590] Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
[ 1.117709] usb usb3: configuration #1 chosen from 1 choice
[ 1.117734] hub 3-0:1.0: USB hub found
[ 1.117739] hub 3-0:1.0: 2 ports detected
[ 1.126078] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 19 (level, low) -> IRQ 19
[ 1.126101] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[ 1.126105] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 1.126122] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 4
[ 1.126152] ehci_hcd 0000:00:1a.7: debug port 1
[ 1.130049] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
[ 1.130058] ehci_hcd 0000:00:1a.7: irq 19, io mem 0xf6504800
[ 1.176056] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[ 1.176089] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.176091] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.176094] usb usb4: Product: EHCI Host Controller
[ 1.176095] usb usb4: Manufacturer: Linux 2.6.32-bpo.5-amd64 ehci_hcd
[ 1.176097] usb usb4: SerialNumber: 0000:00:1a.7
[ 1.176188] usb usb4: configuration #1 chosen from 1 choice
[ 1.176218] hub 4-0:1.0: USB hub found
[ 1.176226] hub 4-0:1.0: 6 ports detected
[ 1.176306] alloc irq_desc for 23 on node -1
[ 1.176308] alloc kstat_irqs on node -1
[ 1.176316] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 1.176326] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 1.176330] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 1.176338] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
[ 1.176378] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001880
[ 1.176413] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.176415] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.176417] usb usb5: Product: UHCI Host Controller
[ 1.176419] usb usb5: Manufacturer: Linux 2.6.32-bpo.5-amd64 uhci_hcd
[ 1.176421] usb usb5: SerialNumber: 0000:00:1d.0
[ 1.176473] usb usb5: configuration #1 chosen from 1 choice
[ 1.176497] hub 5-0:1.0: USB hub found
[ 1.176503] hub 5-0:1.0: 2 ports detected
[ 1.176560] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 1.176593] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 1.176596] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 1.176604] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 6
[ 1.176636] ehci_hcd 0000:00:1d.7: debug port 1
[ 1.180526] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 1.184027] firewire_ohci: Added fw-ohci device 0000:1a:00.0, OHCI version 1.10
[ 1.201823] sdhci: Secure Digital Host Controller Interface driver
[ 1.201826] sdhci: Copyright(c) Pierre Ossman
[ 1.203193] sdhci-pci 0000:1a:00.1: SDHCI controller found [1217:8120] (rev 1)
[ 1.203236] sdhci-pci 0000:1a:00.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.203266] mmc0: Unknown controller version (2). You may experience problems.
[ 1.203328] sdhci-pci 0000:1a:00.1: Will use DMA mode even though HW doesn't fully claim to support it.
[ 1.203342] sdhci-pci 0000:1a:00.1: setting latency timer to 64
[ 1.203384] Registered led device: mmc0::
[ 1.203421] mmc0: SDHCI controller on PCI [0000:1a:00.1] using DMA
[ 1.203579] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf6504c00
[ 1.260033] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 1.260064] usb usb6: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.260066] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.260068] usb usb6: Product: EHCI Host Controller
[ 1.260070] usb usb6: Manufacturer: Linux 2.6.32-bpo.5-amd64 ehci_hcd
[ 1.260072] usb usb6: SerialNumber: 0000:00:1d.7
[ 1.260156] usb usb6: configuration #1 chosen from 1 choice
[ 1.260183] hub 6-0:1.0: USB hub found
[ 1.260191] hub 6-0:1.0: 6 ports detected
[ 1.260267] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1.260276] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 1.260280] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 1.260288] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
[ 1.260320] uhci_hcd 0000:00:1d.1: irq 19, io base 0x000018a0
[ 1.260352] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.260355] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.260357] usb usb7: Product: UHCI Host Controller
[ 1.260358] usb usb7: Manufacturer: Linux 2.6.32-bpo.5-amd64 uhci_hcd
[ 1.260360] usb usb7: SerialNumber: 0000:00:1d.1
[ 1.260407] usb usb7: configuration #1 chosen from 1 choice
[ 1.260434] hub 7-0:1.0: USB hub found
[ 1.260439] hub 7-0:1.0: 2 ports detected
[ 1.260484] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 1.260490] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 1.260493] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 1.260500] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
[ 1.260540] uhci_hcd 0000:00:1d.2: irq 18, io base 0x000018c0
[ 1.260571] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.260574] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.260576] usb usb8: Product: UHCI Host Controller
[ 1.260577] usb usb8: Manufacturer: Linux 2.6.32-bpo.5-amd64 uhci_hcd
[ 1.260579] usb usb8: SerialNumber: 0000:00:1d.2
[ 1.260628] usb usb8: configuration #1 chosen from 1 choice
[ 1.260651] hub 8-0:1.0: USB hub found
[ 1.260657] hub 8-0:1.0: 2 ports detected
[ 1.389235] SCSI subsystem initialized
[ 1.471661] libata version 3.00 loaded.
[ 1.475920] ahci 0000:00:1f.2: version 3.0
[ 1.475938] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1.475981] alloc irq_desc for 31 on node -1
[ 1.475983] alloc kstat_irqs on node -1
[ 1.476008] ahci 0000:00:1f.2: irq 31 for MSI/MSI-X
[ 1.476083] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 4 ports 3 Gbps 0x3 impl SATA mode
[ 1.476086] ahci 0000:00:1f.2: flags: 64bit ncq sntf led clo pmp pio slum part ccc sxs
[ 1.476092] ahci 0000:00:1f.2: setting latency timer to 64
[ 1.477693] scsi0 : ahci
[ 1.478185] scsi1 : ahci
[ 1.478237] scsi2 : ahci
[ 1.478289] scsi3 : ahci
[ 1.478333] ata1: SATA max UDMA/133 abar m2048@0xf6504000 port 0xf6504100 irq 31
[ 1.478337] ata2: SATA max UDMA/133 irq_stat 0x00000040, connection status changed irq 31
[ 1.478339] ata3: DUMMY
[ 1.478340] ata4: DUMMY
[ 1.684075] firewire_core: created device fw0: GUID 00000010a000b000, S400
[ 1.960014] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 2.007191] ata1.00: ATA-8: WDC WD1600BEVT-75ZCT2, 11.01A11, max UDMA/133
[ 2.007194] ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 2.008568] ata1.00: configured for UDMA/133
[ 2.008659] scsi 0:0:0:0: Direct-Access ATA WDC WD1600BEVT-7 11.0 PQ: 0 ANSI: 5
[ 2.364013] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2.365868] ata2.00: ATAPI: PLDS DVD+/-RW DS-8A3S, HD13, max UDMA/100
[ 2.367031] ata2.00: configured for UDMA/100
[ 2.370058] scsi 1:0:0:0: CD-ROM PLDS DVD+-RW DS-8A3S HD13 PQ: 0 ANSI: 5
[ 2.388605] sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[ 2.388653] sd 0:0:0:0: [sda] Write Protect is off
[ 2.388655] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.388676] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.388799] sda: sda1 sda2 sda3
[ 2.441904] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.454859] sr0: scsi3-mmc drive: 24x/8x writer dvd-ram cd/rw xa/form2 cdda pop-up
[ 2.454863] Uniform CD-ROM driver Revision: 3.20
[ 2.454961] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 2.466393] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 2.466849] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 61.088047] eth0: unable to apply firmware patch
[ 61.987101] PM: Starting manual resume from disk
[ 61.987104] PM: Resume from partition 8:2
[ 61.987106] PM: Checking hibernation image.
[ 61.987245] PM: Error -22 checking image file
[ 61.987247] PM: Resume from disk failed.
[ 62.352467] kjournald starting. Commit interval 5 seconds
[ 62.352472] EXT3-fs: mounted filesystem with ordered data mode.
[ 64.363582] udevd version 125 started
[ 65.368313] cfg80211: Using static regulatory domain info
[ 65.368315] cfg80211: Regulatory domain: US
[ 65.368317] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 65.368320] (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
[ 65.368322] (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 65.368325] (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 65.368327] (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 65.368329] (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 65.368332] (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
[ 65.368339] cfg80211: Calling CRDA for country: US
[ 65.410315] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input2
[ 65.410388] ACPI: Lid Switch [LID0]
[ 65.410431] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input3
[ 65.410435] ACPI: Power Button [PWRB]
[ 65.410476] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input4
[ 65.410480] ACPI: Sleep Button [SLPB]
[ 65.410522] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input5
[ 65.410525] ACPI: Power Button [PWRF]
[ 65.493480] input: PC Speaker as /devices/platform/pcspkr/input/input6
[ 65.676971] ACPI: SSDT 000000007db1ac20 00265 (v01 PmRef Cpu0Ist 00003000 INTL 20050624)
[ 65.677469] ACPI: SSDT 000000007db18620 00568 (v01 PmRef Cpu0Cst 00003001 INTL 20050624)
[ 65.738827] Monitor-Mwait will be used to enter C-1 state
[ 65.756093] Monitor-Mwait will be used to enter C-2 state
[ 65.772020] Monitor-Mwait will be used to enter C-3 state
[ 65.772027] Marking TSC unstable due to TSC halts in idle
[ 65.772135] processor LNXCPU:00: registered as cooling_device0
[ 65.772699] ACPI: SSDT 000000007db19ca0 001CF (v01 PmRef ApIst 00003000 INTL 20050624)
[ 65.773058] ACPI: SSDT 000000007db19f20 0008D (v01 PmRef ApCst 00003000 INTL 20050624)
[ 65.785088] Switching to clocksource hpet
[ 65.815105] processor LNXCPU:01: registered as cooling_device1
[ 65.847583] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[ 65.868638] i801_smbus 0000:00:1f.3: PCI INT C -> GSI 19 (level, low) -> IRQ 19
[ 65.868645] ACPI: I/O resource 0000:00:1f.3 [0x1c00-0x1c1f] conflicts with ACPI region SMBI [0x1c00-0x1c0f]
[ 65.868707] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 66.619731] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27ks
[ 66.619734] iwlagn: Copyright(c) 2003-2009 Intel Corporation
[ 66.619839] iwlagn 0000:0e:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 66.619869] iwlagn 0000:0e:00.0: setting latency timer to 64
[ 66.619920] iwlagn 0000:0e:00.0: Detected Intel Wireless WiFi Link 5100AGN REV=0x54
[ 66.790949] iwlagn 0000:0e:00.0: Tunable channels: 13 802.11bg, 24 802.11a channels
[ 66.791014] alloc irq_desc for 32 on node -1
[ 66.791016] alloc kstat_irqs on node -1
[ 66.791038] iwlagn 0000:0e:00.0: irq 32 for MSI/MSI-X
[ 66.939216] ACPI: Battery Slot [BAT1] (battery present)
[ 66.979017] input: PS/2 Mouse as /devices/platform/i8042/serio1/input/input7
[ 67.008298] ACPI: AC Adapter [ACAD] (off-line)
[ 67.025103] input: AlpsPS/2 ALPS GlidePoint as /devices/platform/i8042/serio1/input/input8
[ 67.068301] phy0: Selected rate control algorithm 'iwl-agn-rs'
[ 67.074729] alloc irq_desc for 22 on node -1
[ 67.074732] alloc kstat_irqs on node -1
[ 67.074739] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 67.074779] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 67.209878] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input9
[ 67.220444] input: HDA Intel Mic at Ext Front Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[ 67.220502] input: HDA Intel HP Out at Ext Front Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[ 69.471952] Adding 3903784k swap on /dev/sda2. Priority:-1 extents:1 across:3903784k
[ 69.526074] EXT3 FS on sda3, internal journal
[ 70.401520] loop: module loaded
[ 72.873784] r8169: eth0: link down
[ 72.874095] ADDRCONF(NETDEV_UP): eth0: link is not ready
Reply to: