[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Bug#556106: marked as done (do_IRQ: 0.184 No irq handler for vector)

Your message dated Wed, 9 Jun 2010 18:51:43 +0200
with message-id <20100609165142.GB6699@inutil.org>
and subject line Re: do_IRQ: 0.184 No irq handler for vector
has caused the Debian Bug report #556106,
regarding do_IRQ: 0.184 No irq handler for vector
to be marked as done.

This means that you claim that the problem has been dealt with.
If this is not the case it is now your responsibility to reopen the
Bug report if necessary, and/or fix the problem forthwith.

(NB: If you are a system administrator and have no idea what this
message is talking about, this may indicate a serious mail system
misconfiguration somewhere. Please contact owner@bugs.debian.org
immediately.)


-- 
556106: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=556106
Debian Bug Tracking System
Contact owner@bugs.debian.org with problems
--- Begin Message --- 
Package: linux-image-2.6.26-2-amd64
Version: 2.6.26-19lenny2
Severity: critical
Justification: breaks the whole system


On some disk load (over qla2xxx attached disks) the server prints an 
error and stops (console output attached below).
The same kernel with additional parameter pci=nomsi runs with no any 
problem.

-- Package-specific info:
** Version:
Linux version 2.6.26-2-amd64 (Debian 2.6.26-19lenny2) (dannf@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 SMP Thu Nov 5 02:23:12 UTC 2009

** Command line:
root=/dev/md1 ro console=ttyS0 pci=nomsi 

** Not tainted

** Kernel log:
[   27.101249] ACPI: Power Button (FF) [PWRF]
[   27.155477] input: Power Button (CM) as /class/input/input2
[   27.220046] EDAC MC: Ver: 2.1.0 Nov  5 2009
[   27.303732] EDAC MC0: Giving out device to 'i5000_edac.c' 'I5000': DEV 0000:00:10.0
[   27.394223] EDAC PCI0: Giving out device to module 'i5000_edac' controller 'EDAC PCI controller': DEV '0000:00:10.0' (POLLED)
[   27.659739] ACPI: Power Button (CM) [PWRB]
[   27.740359] tg3.c:v3.92.1 (June 9, 2008)
[   27.787198] ACPI: PCI Interrupt 0000:1e:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[   27.896338] PCI: Setting latency timer of device 0000:1e:00.0 to 64
[   27.904318] intel_rng: FWH not detected
[   27.957061] eth0: Tigon3 [partno(BCM95721) rev 4101 PHY(5750)] (PCI Express) 10/100/1000Base-T Ethernet 00:1b:78:a3:3c:04
[   28.087945] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] WireSpeed[1] TSOcap[1]
[   28.217777] eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[   28.280431] ACPI: PCI Interrupt 0000:1f:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[   28.368896] PCI: Setting latency timer of device 0000:1f:00.0 to 64
[   28.368872] input: PC Speaker as /class/input/input3
[   28.409888] eth1: Tigon3 [partno(BCM95721) rev 4101 PHY(5750)] (PCI Express) 10/100/1000Base-T Ethernet 00:1b:78:a3:3c:05
[   28.409891] eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
[   28.409893] eth1: dma_rwctrl[76180000] dma_mask[64-bit]
[   28.891576] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   29.005148] ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 19
[   29.212328] Error: Driver 'pcspkr' is already registered, aborting...
[   29.777999] ata1.00: configured for UDMA/100
[   29.876317] ata1: EH complete
[   29.924217] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[   29.924225] ata2.00: configured for UDMA/100
[   29.924225] ata2: EH complete
[   30.161445] sd 0:0:0:0: [sda] Write Protect is off
[   30.236991] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   30.237015] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   30.358530] sd 1:0:0:0: [sdb] 312581808 512-byte hardware sectors (160042 MB)
[   30.444842] sd 1:0:0:0: [sdb] Write Protect is off
[   30.502032] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[   30.502054] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   31.033228] Adding 7815480k swap on /dev/md3.  Priority:-1 extents:1 across:7815480k
[   31.451098] EXT3 FS on md1, internal journal
[   32.210188] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
[   32.292063] iTCO_wdt: Found a 631xESB/632xESB TCO device (Version=2, TCOBASE=0x1060)
[   32.424999] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[   32.565092] QLogic Fibre Channel HBA Driver: 8.02.01-k4
[   32.627511] ACPI: PCI Interrupt 0000:0b:01.0[A] -> GSI 24 (level, low) -> IRQ 24
[   32.743210] qla2xxx 0000:0b:01.0: Found an ISP2422, irq 24, iobase 0xffffc20000c52000
[   32.836803] qla2xxx 0000:0b:01.0: Configuring PCI space...
[   32.903412] qla2xxx 0000:0b:01.0: Configure NVRAM parameters...
[   33.010147] qla2xxx 0000:0b:01.0: Verifying loaded RISC code...
[   33.097421] firmware: requesting ql2400_fw.bin
[   33.408531] qla2xxx 0000:0b:01.0: Allocated (64 KB) for EFT...
[   33.478243] qla2xxx 0000:0b:01.0: Allocated (1413 KB) for firmware dump...
[   33.665758] scsi6 : qla2xxx
[   33.699227] qla2xxx 0000:0b:01.0: 
[   33.699227]  QLogic Fibre Channel HBA Driver: 8.02.01-k4
[   33.699227]   QLogic HP AE369-60001 - QLA2340
[   33.699227]   ISP2422: PCI-X Mode 1 (133 MHz) @ 0000:0b:01.0 hdma+, host#=6, fw=4.04.09 [IP] [84XX] 
[   34.093819] qla2xxx 0000:0b:01.0: LIP reset occured (f700).
[   34.193897] ACPI: PCI Interrupt 0000:0b:01.1[B] -> GSI 25 (level, low) -> IRQ 25
[   34.293972] qla2xxx 0000:0b:01.1: Found an ISP2422, irq 25, iobase 0xffffc20000c54000
[   34.387578] qla2xxx 0000:0b:01.1: Configuring PCI space...
[   34.489901] qla2xxx 0000:0b:01.1: Configure NVRAM parameters...
[   34.606863] qla2xxx 0000:0b:01.1: Verifying loaded RISC code...
[   34.938970] qla2xxx 0000:0b:01.1: Allocated (64 KB) for EFT...
[   35.092599] qla2xxx 0000:0b:01.1: Allocated (1413 KB) for firmware dump...
[   35.216869] scsi7 : qla2xxx
[   35.253266] qla2xxx 0000:0b:01.1: 
[   35.253266]  QLogic Fibre Channel HBA Driver: 8.02.01-k4
[   35.253266]   QLogic HP AE369-60001 - QLA2340
[   35.253266]   ISP2422: PCI-X Mode 1 (133 MHz) @ 0000:0b:01.1 hdma+, host#=7, fw=4.04.09 [IP] [84XX] 
[   35.305352] qla2xxx 0000:0b:01.0: LOOP UP detected (4 Gbps).
[   35.485352] qla2xxx 0000:0b:01.1: LIP reset occured (f700).
[   35.716082] device-mapper: uevent: version 1.0.3
[   35.782401] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
[   36.048024] device-mapper: multipath: version 1.0.5 loaded
[   36.148546] scsi 6:0:0:0: RAID              HP       HSV200           6200 PQ: 0 ANSI: 5
[   36.339091] scsi 6:0:1:0: RAID              HP       HSV200           6200 PQ: 0 ANSI: 5
[   36.835918] qla2xxx 0000:0b:01.1: LOOP UP detected (4 Gbps).
[   37.437596] scsi 7:0:0:0: RAID              HP       HSV200           6200 PQ: 0 ANSI: 5
[   37.633547] scsi 7:0:1:0: RAID              HP       HSV200           6200 PQ: 0 ANSI: 5
[   38.407601] kjournald starting.  Commit interval 5 seconds
[   38.476493] EXT3 FS on md0, internal journal
[   38.555496] EXT3-fs: mounted filesystem with ordered data mode.
[   38.817899] kjournald starting.  Commit interval 5 seconds
[   38.901897] EXT3 FS on md2, internal journal
[   38.971514] EXT3-fs: mounted filesystem with ordered data mode.
[   39.168308] kjournald starting.  Commit interval 5 seconds
[   39.307205] EXT3 FS on md4, internal journal
[   39.358506] EXT3-fs: mounted filesystem with ordered data mode.
[   42.814687] tg3: eth0: Link is up at 1000 Mbps, full duplex.
[   42.868110] tg3: eth0: Flow control is off for TX and off for RX.
[   44.319223] tg3: eth1: Link is up at 1000 Mbps, full duplex.
[   44.427939] tg3: eth1: Flow control is on for TX and on for RX.
[   63.915387] warning: `ntpd' uses 32-bit capabilities (legacy support in use)

** Loaded modules:
Module                  Size  Used by
dm_multipath           21392  0 
dm_mod                 58864  1 dm_multipath
qla2xxx               173812  0 
firmware_class         12544  1 qla2xxx
scsi_transport_fc      49668  1 qla2xxx
scsi_tgt               17616  1 scsi_transport_fc
iTCO_wdt               15696  1 
snd_pcm                81800  0 
snd_timer              25744  1 snd_pcm
snd                    63688  2 snd_pcm,snd_timer
soundcore              12064  1 snd
snd_page_alloc         13072  1 snd_pcm
serio_raw               9988  0 
i2c_i801               13596  0 
shpchp                 34208  0 
psmouse                42268  0 
i2c_core               27936  1 i2c_i801
pcspkr                  7040  0 
rng_core                8968  0 
tg3                    97156  0 
i5000_edac             12936  0 
edac_core              49560  3 i5000_edac
pci_hotplug            32056  1 shpchp
container               8320  0 
button                 11680  0 
evdev                  14208  0 
thermal                22688  0 
processor              42304  1 thermal
fan                     9352  0 
thermal_sys            17728  3 thermal,processor,fan
ahci                   33036  10 
libata                165600  1 ahci
dock                   14112  1 libata
raid1                  24192  5 
md_mod                 80292  6 raid1
ext3                  125072  4 
jbd                    51240  1 ext3
mbcache                12804  1 ext3
sd_mod                 29376  12 
scsi_mod              161016  5 qla2xxx,scsi_transport_fc,scsi_tgt,libata,sd_mod

** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 5000X Chipset Memory Controller Hub [8086:25c0] (rev 31)
	Subsystem: Intel Corporation 5000X Chipset Memory Controller Hub [8086:25c0]
	Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 0
	Capabilities: <access denied>

00:02.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI Express x8 Port 2-3 [8086:25f7] (rev 31) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Bus: primary=00, secondary=01, subordinate=0b, sec-latency=0
	I/O behind bridge: 00002000-00002fff
	Memory behind bridge: df900000-dfafffff
	Prefetchable memory behind bridge: 00000000d1000000-00000000d10fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport-driver
	Kernel modules: shpchp

00:03.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI Express x4 Port 3 [8086:25e3] (rev 31) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Bus: primary=00, secondary=0c, subordinate=0c, sec-latency=0
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport-driver
	Kernel modules: shpchp

00:04.0 PCI bridge [0604]: Intel Corporation 5000X Chipset PCI Express x16 Port 4-7 [8086:25fa] (rev 31) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Bus: primary=00, secondary=10, subordinate=10, sec-latency=0
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport-driver
	Kernel modules: shpchp

00:05.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI Express x4 Port 5 [8086:25e5] (rev 31) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Bus: primary=00, secondary=11, subordinate=11, sec-latency=0
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport-driver
	Kernel modules: shpchp

00:06.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI Express x4 Port 6 [8086:25e6] (rev 31) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Bus: primary=00, secondary=12, subordinate=12, sec-latency=0
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport-driver
	Kernel modules: shpchp

00:07.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI Express x4 Port 7 [8086:25e7] (rev 31) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Bus: primary=00, secondary=13, subordinate=13, sec-latency=0
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport-driver
	Kernel modules: shpchp

00:10.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset FSB Registers [8086:25f0] (rev 31)
	Subsystem: Hewlett-Packard Company Device [103c:31fd]
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Kernel driver in use: i5000_edac
	Kernel modules: i5000_edac

00:10.1 Host bridge [0600]: Intel Corporation 5000 Series Chipset FSB Registers [8086:25f0] (rev 31)
	Subsystem: Hewlett-Packard Company Device [103c:31fd]
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Kernel modules: i5000_edac

00:10.2 Host bridge [0600]: Intel Corporation 5000 Series Chipset FSB Registers [8086:25f0] (rev 31)
	Subsystem: Hewlett-Packard Company Device [103c:31fd]
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Kernel modules: i5000_edac

00:11.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset Reserved Registers [8086:25f1] (rev 31)
	Subsystem: Hewlett-Packard Company Device [103c:31fd]
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:13.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset Reserved Registers [8086:25f3] (rev 31)
	Subsystem: Hewlett-Packard Company Device [103c:31fd]
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:15.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset FBD Registers [8086:25f5] (rev 31)
	Subsystem: Hewlett-Packard Company Device [103c:31fd]
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:16.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset FBD Registers [8086:25f6] (rev 31)
	Subsystem: Hewlett-Packard Company Device [103c:31fd]
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:1c.0 PCI bridge [0604]: Intel Corporation 631xESB/632xESB/3100 Chipset PCI Express Root Port 1 [8086:2690] (rev 09) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Bus: primary=00, secondary=1e, subordinate=1e, sec-latency=0
	Memory behind bridge: dfb00000-dfbfffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport-driver
	Kernel modules: shpchp

00:1c.1 PCI bridge [0604]: Intel Corporation 631xESB/632xESB/3100 Chipset PCI Express Root Port 2 [8086:2692] (rev 09) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Bus: primary=00, secondary=1f, subordinate=1f, sec-latency=0
	Memory behind bridge: dfc00000-dfcfffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport-driver
	Kernel modules: shpchp

00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev d9) (prog-if 01 [Subtractive decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Bus: primary=00, secondary=20, subordinate=20, sec-latency=32
	Memory behind bridge: df000000-df8fffff
	Prefetchable memory behind bridge: 00000000de000000-00000000deffffff
	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity+ SERR+ NoISA+ VGA+ MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>

00:1f.0 ISA bridge [0601]: Intel Corporation 631xESB/632xESB/3100 Chipset LPC Interface Controller [8086:2670] (rev 09)
	Subsystem: Hewlett-Packard Company Device [103c:31fe]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Kernel modules: iTCO_wdt, intel-rng

00:1f.2 SATA controller [0106]: Intel Corporation 631xESB/632xESB SATA AHCI Controller [8086:2681] (rev 09) (prog-if 01 [AHCI 1.0])
	Subsystem: Hewlett-Packard Company Device [103c:31fe]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 19
	Region 0: I/O ports at 1830 [size=8]
	Region 1: I/O ports at 1824 [size=4]
	Region 2: I/O ports at 1828 [size=8]
	Region 3: I/O ports at 1820 [size=4]
	Region 4: I/O ports at 1800 [size=32]
	Region 5: Memory at dff00000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: <access denied>
	Kernel driver in use: ahci
	Kernel modules: ahci

00:1f.3 SMBus [0c05]: Intel Corporation 631xESB/632xESB/3100 Chipset SMBus Controller [8086:269b] (rev 09)
	Subsystem: Hewlett-Packard Company Device [103c:31fe]
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin B routed to IRQ 19
	Region 4: I/O ports at 1840 [size=32]
	Kernel driver in use: i801_smbus
	Kernel modules: i2c-i801

01:00.0 PCI bridge [0604]: Intel Corporation 6311ESB/6321ESB PCI Express Upstream Port [8086:3500] (rev 01) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Bus: primary=01, secondary=02, subordinate=03, sec-latency=0
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport-driver
	Kernel modules: shpchp

01:00.3 PCI bridge [0604]: Intel Corporation 6311ESB/6321ESB PCI Express to PCI-X Bridge [8086:350c] (rev 01) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=01, secondary=0b, subordinate=0b, sec-latency=64
	I/O behind bridge: 00002000-00002fff
	Memory behind bridge: dfa00000-dfafffff
	Prefetchable memory behind bridge: 00000000d1000000-00000000d10fffff
	Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel modules: shpchp

02:00.0 PCI bridge [0604]: Intel Corporation 6311ESB/6321ESB PCI Express Downstream Port E1 [8086:3510] (rev 01) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Bus: primary=02, secondary=03, subordinate=03, sec-latency=0
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport-driver
	Kernel modules: shpchp

0b:01.0 Fibre Channel [0c04]: QLogic Corp. ISP2422-based 4Gb Fibre Channel to PCI-X HBA [1077:2422] (rev 02)
	Subsystem: QLogic Corp. Device [1077:0148]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 128 (16000ns min), Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 24
	Region 0: I/O ports at 2000 [size=256]
	Region 1: Memory at dfa00000 (64-bit, non-prefetchable) [size=4K]
	[virtual] Expansion ROM at d1000000 [disabled] [size=256K]
	Capabilities: <access denied>
	Kernel driver in use: qla2xxx
	Kernel modules: qla2xxx

0b:01.1 Fibre Channel [0c04]: QLogic Corp. ISP2422-based 4Gb Fibre Channel to PCI-X HBA [1077:2422] (rev 02)
	Subsystem: QLogic Corp. Device [1077:0148]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 128 (16000ns min), Cache Line Size: 32 bytes
	Interrupt: pin B routed to IRQ 25
	Region 0: I/O ports at 2400 [size=256]
	Region 1: Memory at dfa01000 (64-bit, non-prefetchable) [size=4K]
	[virtual] Expansion ROM at d1040000 [disabled] [size=256K]
	Capabilities: <access denied>
	Kernel driver in use: qla2xxx
	Kernel modules: qla2xxx

1e:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express [14e4:1659] (rev 11)
	Subsystem: Hewlett-Packard Company Device [103c:3260]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at dfb00000 (64-bit, non-prefetchable) [size=64K]
	Expansion ROM at <ignored> [disabled]
	Capabilities: <access denied>
	Kernel driver in use: tg3
	Kernel modules: tg3

1f:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express [14e4:1659] (rev 11)
	Subsystem: Hewlett-Packard Company Device [103c:3260]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 17
	Region 0: Memory at dfc00000 (64-bit, non-prefetchable) [size=64K]
	Expansion ROM at <ignored> [disabled]
	Capabilities: <access denied>
	Kernel driver in use: tg3
	Kernel modules: tg3

20:02.0 VGA compatible controller [0300]: Matrox Graphics, Inc. MGA G200e [Pilot] ServerEngines (SEP1) [102b:0522] (rev 02) (prog-if 00 [VGA controller])
	Subsystem: Hewlett-Packard Company Device [103c:31fa]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 128 (4000ns min, 8000ns max), Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 5
	Region 0: Memory at de000000 (32-bit, prefetchable) [size=16M]
	Region 1: Memory at df800000 (32-bit, non-prefetchable) [size=16K]
	Region 2: Memory at df000000 (32-bit, non-prefetchable) [size=8M]
	[virtual] Expansion ROM at df810000 [disabled] [size=64K]
	Capabilities: <access denied>



-- System Information:
Debian Release: 5.0.3
  APT prefers stable
  APT policy: (500, 'stable')
Architecture: amd64 (x86_64)

Kernel: Linux 2.6.26-2-amd64 (SMP w/4 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash

Versions of packages linux-image-2.6.26-2-amd64 depends on:
ii  debconf [debconf-2.0]         1.5.24     Debian configuration management sy
ii  initramfs-tools [linux-initra 0.92o      tools for generating an initramfs
ii  module-init-tools             3.4-1      tools for managing Linux kernel mo

linux-image-2.6.26-2-amd64 recommends no packages.

Versions of packages linux-image-2.6.26-2-amd64 suggests:
ii  grub                       0.97-47lenny2 GRand Unified Bootloader (Legacy v
pn  linux-doc-2.6.26           <none>        (no description available)

-- debconf information excluded

[93543.093300] qla2xxx 0000:0b:01.0: Mailbox command timeout occured. Issuing ISP abort.
[93543.187021] qla2xxx 0000:0b:01.0: Performing ISP error recovery - ha= ffff81022b8985f8.
[93544.168312] qla2xxx 0000:0b:01.0: LIP reset occured (f700).
[93545.488056] qla2xxx 0000:0b:01.0: LOOP UP detected (4 Gbps).
[93545.684498] do_IRQ: 0.184 No irq handler for vector
[93545.800455] int3: 0000 [1] SMP 
[93545.836381] CPU 0 
[93545.836381] Modules linked in: dm_round_robin dm_multipath dm_mod qla2xxx firmware_class scsi_transport_fc scsi_tgt iTCO_wdt snd_pcm snd_timer snd soundcore snd_page_alloc i2c_i801 serio_raw i2c_core container tg3 rng_core pcspkr psmouse shpchp button pci_hotplug i5000_edac edac_core evdev thermal processor fan thermal_sys ahci libata dock raid1 md_mod ext3 jbd mbcache sd_mod scsi_mod
[93546.363711] Pid: 0, comm: swapper Not tainted 2.6.26-2-amd64 #1
[93546.451197] RIP: 0010:[<ffffffff8057d0f1>]  [<ffffffff8057d0f1>] _sinittext+0xf1/0x140
[93546.558593] RSP: 0000:ffffffff80575f18  EFLAGS: 00000046
[93546.558593] RAX: 0000000000000000 RBX: ffffffff80212c3f RCX: 0000000000000000
[93546.717564] RDX: 0000000000000000 RSI: 0000000000000001 RDI: ffffffff804fbe70
[93546.717564] RBP: 0000000000000000 R08: ffff8100010356a0 R09: 00008fb6f7876db6
[93546.717564] R10: ffff81022b891990 R11: ffffffff8021a827 R12: ffffffffffffffff
[93546.717564] R13: ffffffff805a5900 R14: ffffffff805a64c0 R15: 0000000000000000
[93546.717564] FS:  0000000000000000(0000) GS:ffffffff8053c000(0000) knlGS:0000000000000000
[93547.171510] CS:  0010 DS: 0018 ES: 0018 CR0: 000000008005003b
[93547.171510] CR2: 00007ffe29eb6218 CR3: 00000001e7c6a000 CR4: 00000000000006e0
[93547.171510] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[93547.171510] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[93547.171510] Process swapper (pid: 0, threadinfo ffffffff80574000, task ffffffff804f9480)
[93547.171510] Stack:  ffffffff80212c80 0000000000000010 0000000000000246 ffffffff80575f40
[93547.171510]  0000000000000000 ffffffff8020ac79 0000000000000020 ffffffff8057ddd1
[93547.171510]  0000000000000000 ffffffff8058e5d6 ffffffff805a64c0 0000000000675398
[93547.171510] Call Trace:
[93547.171510]  [<ffffffff80212c80>] mwait_idle+0x41/0x4d
[93547.171510]  [<ffffffff8020ac79>] cpu_idle+0x89/0xb3
[93547.171510] 
[93547.171510] 
[93547.171510] Code: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc <cc> cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc 
[93548.344319] RIP  [<ffffffff8057d0f1>] _sinittext+0xf1/0x140
[93548.344319]  RSP <ffffffff80575f18>
[93548.344319] ---[ end trace f2c19baabbb385ea ]---
[93548.344319] Kernel panic - not syncing: Attempted to kill the idle task!

--- End Message ---
--- Begin Message --- 
Version: 2.6.32-1

On Tue, Jun 08, 2010 at 05:08:42PM +0300, Andrejs Dubovskis wrote:
> Hi!
> >> Package: linux-image-2.6.26-2-amd64
> >> > Version: 2.6.26-19lenny2
> >> > Severity: critical
> >> > Justification: breaks the whole system
> >> > 
> >> > 
> >> > On some disk load (over qla2xxx attached disks) the server prints an 
> >> > error and stops (console output attached below).
> >> > The same kernel with additional parameter pci=nomsi runs with no any 
> >> > problem.
> 
> > The next release of Debian (6.0, code name Squeeze) will be based
> > on 2.6.32. Please test the current 2.6.32 from unstable/testing and tell
> > us whether the problem persists. If so, we should report it upstream
> > to the kernel.org developers.
> > 
> > The 2.6.32 kernel is available from packages.debian.org and can
> > be installed in both Debian stable, testing and unstable
> > installations.
> 
> During few hours I was unable to reproduce the error on lenny with kernel from
> testing. A hardware was exactly the same as before.
> 
> Thank you.

Thanks for the feedback, marking as closed.

Cheers,
        Moritz

--- End Message ---
Reply to: