[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Bug#516476: marked as done (linux-image-2.6.26-1-amd64: iwl3945 dosen't not run on dell latitude d820)



Your message dated Sun, 30 May 2010 23:47:00 +0200
with message-id <20100530214700.GA9111@galadriel.inutil.org>
and subject line Re: linux-image-2.6.26-1-amd64: iwl3945 dosen't not run on dell latitude d820
has caused the Debian Bug report #516476,
regarding linux-image-2.6.26-1-amd64: iwl3945 dosen't not run on dell latitude d820
to be marked as done.

This means that you claim that the problem has been dealt with.
If this is not the case it is now your responsibility to reopen the
Bug report if necessary, and/or fix the problem forthwith.

(NB: If you are a system administrator and have no idea what this
message is talking about, this may indicate a serious mail system
misconfiguration somewhere. Please contact owner@bugs.debian.org
immediately.)


-- 
516476: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=516476
Debian Bug Tracking System
Contact owner@bugs.debian.org with problems
--- Begin Message ---
Package: linux-image-2.6.26-1-amd64
Version: 2.6.26-13
Severity: normal

I can't connect to my AP after upgrate to new kernel.

Try to switch off/on hardware plug of wifi card. Try reload iwl3945
modules. Try reinstall firmware-iwlwifi.

-- Package-specific info:
** Version:
Linux version 2.6.26-1-amd64 (Debian 2.6.26-13) (waldi@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-24)) #1 SMP Sat Jan 10 19:55:48 UTC 2009

** Command line:
root=UUID=7ddd1541-6755-42a0-b492-f2874378c1f4 ro resume2=swap:/dev/sda3 quiet vga=795 agp=off usbcore.autosuspend=1 

** Tainted: P (1)

** Kernel log:
[   85.597405] CE: hpet increasing min_delta_ns to 15000 nsec
[  141.571066] CPU0 attaching NULL sched-domain.
[  141.571078] CPU1 attaching NULL sched-domain.
[  141.590120] CPU0 attaching sched-domain:
[  141.590128]  domain 0: span 0-1
[  141.590132]   groups: 0 1
[  141.590139]   domain 1: span 0-1
[  141.590142]    groups: 0-1
[  141.590148] CPU1 attaching sched-domain:
[  141.590151]  domain 0: span 0-1
[  141.590155]   groups: 1 0
[  141.590160]   domain 1: span 0-1
[  141.590163]    groups: 0-1
[  145.234132] CE: hpet increasing min_delta_ns to 22500 nsec
[  185.055432] ACPI: PCI interrupt for device 0000:0c:00.0 disabled
[  189.413099] ACPI: PCI Interrupt 0000:0c:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[  189.416861] PM: Writing back config space on device 0000:0c:00.0 at offset 1 (was 100102, writing 100106)
[  189.460571] Registered led device: iwl-phy0:radio
[  189.460593] Registered led device: iwl-phy0:assoc
[  189.460651] Registered led device: iwl-phy0:RX
[  189.460669] Registered led device: iwl-phy0:TX
[  189.474998] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  267.211877] device wlan0 entered promiscuous mode
[  272.314445] device wlan0 left promiscuous mode
[  272.565899] ACPI: PCI interrupt for device 0000:0c:00.0 disabled
[  275.036480] ACPI: PCI Interrupt 0000:0c:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[  275.036642] PM: Writing back config space on device 0000:0c:00.0 at offset 1 (was 100102, writing 100106)
[  275.080905] Registered led device: iwl-phy0:radio
[  275.080988] Registered led device: iwl-phy0:assoc
[  275.081022] Registered led device: iwl-phy0:RX
[  275.081056] Registered led device: iwl-phy0:TX
[  275.102928] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  280.133610] tg3: eth0: Link is up at 100 Mbps, full duplex.
[  280.133610] tg3: eth0: Flow control is on for TX and on for RX.
[  280.133610] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  281.723110] IPv6 addrconf: prefix with wrong length 48
[  289.761094] device eth0 entered promiscuous mode
[  291.256852] device eth0 left promiscuous mode
[  293.441181] IPv6 addrconf: prefix with wrong length 48
[  578.263001] CE: hpet increasing min_delta_ns to 33750 nsec
[  578.263096] CE: hpet increasing min_delta_ns to 50624 nsec
[  881.301816] IPv6 addrconf: prefix with wrong length 48
[ 1006.321801] ACPI: PCI interrupt for device 0000:0c:00.0 disabled
[ 1010.919378] IPv6 addrconf: prefix with wrong length 48
[ 1028.450042] ACPI: PCI Interrupt 0000:0c:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 1028.450212] PM: Writing back config space on device 0000:0c:00.0 at offset 1 (was 100102, writing 100106)
[ 1028.498950] Registered led device: iwl-phy0:radio
[ 1028.498950] Registered led device: iwl-phy0:assoc
[ 1028.498950] Registered led device: iwl-phy0:RX
[ 1028.498950] Registered led device: iwl-phy0:TX
[ 1028.551096] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1262.090093] IPv6 addrconf: prefix with wrong length 48
[ 1690.157875] ACPI: PCI interrupt for device 0000:0c:00.0 disabled
[ 1694.335886] iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, 1.2.26ks
[ 1694.335886] iwl3945: Copyright(c) 2003-2008 Intel Corporation
[ 1694.335886] ACPI: PCI Interrupt 0000:0c:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 1694.335886] PCI: Setting latency timer of device 0000:0c:00.0 to 64
[ 1694.335886] iwl3945: Detected Intel Wireless WiFi Link 3945ABG
[ 1694.379568] iwl3945: Tunable channels: 13 802.11bg, 23 802.11a channels
[ 1694.380075] phy1: Selected rate control algorithm 'iwl-3945-rs'
[ 1694.419570] ACPI: PCI Interrupt 0000:0c:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 1694.419570] firmware: requesting iwlwifi-3945-1.ucode
[ 1694.471570] Registered led device: iwl-phy1:radio
[ 1694.471570] Registered led device: iwl-phy1:assoc
[ 1694.471570] Registered led device: iwl-phy1:RX
[ 1694.471570] Registered led device: iwl-phy1:TX
[ 1694.486175] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1794.973848] ACPI: PCI Interrupt 0000:0c:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 1795.019099] Registered led device: iwl-phy1:radio
[ 1795.019122] Registered led device: iwl-phy1:assoc
[ 1795.019180] Registered led device: iwl-phy1:RX
[ 1795.019200] Registered led device: iwl-phy1:TX
[ 1795.032375] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1797.780362] IPv6 addrconf: prefix with wrong length 48
[ 2157.259347] IPv6 addrconf: prefix with wrong length 48
[ 2431.206473] IPv6 addrconf: prefix with wrong length 48
[ 2497.907206] iwl3945: Radio Frequency Kill Switch is On:
[ 2497.907206] Kill switch must be turned off for wireless networking to work.
[ 2498.149713] usb 5-2.3: USB disconnect, address 4
[ 2498.852093] Registered led device: iwl-phy1:radio
[ 2498.852116] Registered led device: iwl-phy1:assoc
[ 2498.852172] Registered led device: iwl-phy1:RX
[ 2498.852189] Registered led device: iwl-phy1:TX
[ 2498.890023] iwl3945: Radio Frequency Kill Switch is On:
[ 2498.890025] Kill switch must be turned off for wireless networking to work.
[ 2499.137982] iwl3945: Radio Frequency Kill Switch is On:
[ 2499.137982] Kill switch must be turned off for wireless networking to work.
[ 2499.144081] iwl3945: WARNING: Requesting MAC access during RFKILL wakes up NIC
[ 2499.153125] iwl3945: WARNING: Requesting MAC access during RFKILL wakes up NIC
[ 2499.173127] iwl3945: WARNING: Requesting MAC access during RFKILL wakes up NIC
[ 2499.201135] iwl3945: WARNING: Requesting MAC access during RFKILL wakes up NIC
[ 2500.018897] Registered led device: iwl-phy1:radio
[ 2500.018979] Registered led device: iwl-phy1:assoc
[ 2500.019014] Registered led device: iwl-phy1:RX
[ 2500.019049] Registered led device: iwl-phy1:TX
[ 2500.279547] usb 5-2.3: new full speed USB device using ehci_hcd and address 5
[ 2500.424171] usb 5-2.3: configuration #1 chosen from 1 choice
[ 2500.427201] usb 5-2.3: New USB device found, idVendor=413c, idProduct=8103
[ 2500.427211] usb 5-2.3: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 2716.107338] IPv6 addrconf: prefix with wrong length 48

** Loaded modules:
Module                  Size  Used by
tcp_diag                5888  0 
inet_diag              13968  1 tcp_diag
iwl3945                92916  0 
nvidia               8104944  26 
binfmt_misc            13580  1 
rfcomm                 38176  4 
l2cap                  23936  9 rfcomm
cpufreq_ondemand       11792  1 
kvm_intel              39776  0 
kvm                   127464  1 kvm_intel
irtty_sir               9728  0 
sir_dev                16904  1 irtty_sir
ppdev                  11656  0 
parport_pc             31016  0 
lp                     14724  0 
parport                41776  3 ppdev,parport_pc,lp
ipv6                  288328  20 
fuse                   53184  1 
dm_snapshot            19400  0 
dm_mirror              20608  0 
dm_log                 13956  1 dm_mirror
dm_mod                 58864  3 dm_snapshot,dm_mirror,dm_log
acpi_cpufreq           11792  1 
freq_table              9344  2 cpufreq_ondemand,acpi_cpufreq
sbp2                   25356  0 
loop                   19468  0 
rng_core                8968  0 
snd_hda_intel         434904  1 
snd_pcm_oss            41760  0 
snd_mixer_oss          18816  2 snd_pcm_oss
arc4                    6272  2 
snd_pcm                81672  2 snd_hda_intel,snd_pcm_oss
snd_seq_dummy           7428  0 
ecb                     7296  2 
snd_seq_oss            33152  0 
crypto_blkcipher       21636  1 ecb
pcmcia                 38680  0 
i2c_i801               13596  0 
snd_seq_midi           11072  0 
snd_rawmidi            26784  1 snd_seq_midi
snd_seq_midi_event     11904  2 snd_seq_oss,snd_seq_midi
irda                  117732  1 sir_dev
snd_seq                54304  6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
firmware_class         12544  2 iwl3945,pcmcia
mac80211              162864  1 iwl3945
led_class               8968  1 iwl3945
iTCO_wdt               15696  0 
crc_ccitt               6528  1 irda
yenta_socket           27916  1 
rsrc_nonstatic         14080  1 yenta_socket
pcmcia_core            41508  3 pcmcia,yenta_socket,rsrc_nonstatic
i2c_core               27936  2 nvidia,i2c_i801
hci_usb                18460  2 
psmouse                42268  0 
serio_raw               9860  0 
bluetooth              57124  7 rfcomm,l2cap,hci_usb
video                  24212  10 
output                  7808  1 video
cfg80211               30224  2 iwl3945,mac80211
wmi                    11712  0 
button                 11680  0 
battery                16904  0 
snd_timer              25744  2 snd_pcm,snd_seq
snd_seq_device         11668  5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
ac                      9352  0 
snd                    63688  9 snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
soundcore              12064  2 snd
snd_page_alloc         13072  2 snd_hda_intel,snd_pcm
evdev                  14208  11 
dcdbas                 11952  0 
jfs                   157904  1 
nls_base               12932  1 jfs
sg                     36448  0 
sr_mod                 19652  0 
cdrom                  37928  1 sr_mod
sd_mod                 29376  3 
ide_pci_generic         9220  0 [permanent]
ide_core              128284  1 ide_pci_generic
ata_piix               22660  2 
ata_generic            10116  0 
ohci1394               32564  0 
libata                165472  2 ata_piix,ata_generic
scsi_mod              160760  5 sbp2,sg,sr_mod,sd_mod,libata
ieee1394               93816  2 sbp2,ohci1394
ehci_hcd               36108  0 
uhci_hcd               25760  0 
tg3                    97156  0 
dock                   14112  1 libata
thermal                22688  0 
processor              42304  4 acpi_cpufreq,thermal
fan                     9352  0 
thermal_sys            17728  4 video,thermal,processor,fan

** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub [8086:27a0] (rev 03)
	Subsystem: Dell Device [1028:01cc]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
	Latency: 0
	Capabilities: <access denied>
	Kernel modules: intel-agp

00:01.0 PCI bridge [0604]: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express PCI Express Root Port [8086:27a1] (rev 03) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	Memory behind bridge: ed000000-efefffff
	Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport-driver
	Kernel modules: shpchp

00:1b.0 Audio device [0403]: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller [8086:27d8] (rev 01)
	Subsystem: Dell Device [1028:01cc]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 21
	Region 0: Memory at efffc000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: <access denied>
	Kernel driver in use: HDA Intel
	Kernel modules: snd-hda-intel

00:1c.0 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 [8086:27d0] (rev 01) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=0b, subordinate=0b, sec-latency=0
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport-driver
	Kernel modules: shpchp

00:1c.1 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 [8086:27d2] (rev 01) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=0c, subordinate=0c, sec-latency=0
	Memory behind bridge: ecf00000-ecffffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport-driver
	Kernel modules: shpchp

00:1c.2 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3 [8086:27d4] (rev 01) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=09, subordinate=09, sec-latency=0
	Memory behind bridge: ece00000-ecefffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport-driver
	Kernel modules: shpchp

00:1c.3 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 4 [8086:27d6] (rev 01) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=0d, subordinate=0e, sec-latency=0
	I/O behind bridge: 0000e000-0000efff
	Memory behind bridge: ecc00000-ecdfffff
	Prefetchable memory behind bridge: 00000000e0000000-00000000e01fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport-driver
	Kernel modules: shpchp

00:1d.0 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 [8086:27c8] (rev 01) (prog-if 00 [UHCI])
	Subsystem: Dell Device [1028:01cc]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 20
	Region 4: I/O ports at bf80 [size=32]
	Kernel driver in use: uhci_hcd
	Kernel modules: uhci-hcd

00:1d.1 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 [8086:27c9] (rev 01) (prog-if 00 [UHCI])
	Subsystem: Dell Device [1028:01cc]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 21
	Region 4: I/O ports at bf60 [size=32]
	Kernel driver in use: uhci_hcd
	Kernel modules: uhci-hcd

00:1d.2 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 [8086:27ca] (rev 01) (prog-if 00 [UHCI])
	Subsystem: Dell Device [1028:01cc]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin C routed to IRQ 22
	Region 4: I/O ports at bf40 [size=32]
	Kernel driver in use: uhci_hcd
	Kernel modules: uhci-hcd

00:1d.3 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 [8086:27cb] (rev 01) (prog-if 00 [UHCI])
	Subsystem: Dell Device [1028:01cc]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin D routed to IRQ 23
	Region 4: I/O ports at bf20 [size=32]
	Kernel driver in use: uhci_hcd
	Kernel modules: uhci-hcd

00:1d.7 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller [8086:27cc] (rev 01) (prog-if 20 [EHCI])
	Subsystem: Dell Device [1028:01cc]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 20
	Region 0: Memory at ffa80000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: <access denied>
	Kernel driver in use: ehci_hcd
	Kernel modules: ehci-hcd

00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e1) (prog-if 01 [Subtractive decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Bus: primary=00, secondary=03, subordinate=07, sec-latency=32
	I/O behind bridge: 00002000-00002fff
	Memory behind bridge: ecb00000-ecbfffff
	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR+
	BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>

00:1f.0 ISA bridge [0601]: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge [8086:27b9] (rev 01)
	Subsystem: Dell Device [1028:01cc]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Capabilities: <access denied>
	Kernel modules: intel-rng, iTCO_wdt

00:1f.2 IDE interface [0101]: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller [8086:27c4] (rev 01) (prog-if 80 [Master])
	Subsystem: Dell Device [1028:01cc]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 17
	Region 0: I/O ports at 01f0 [size=8]
	Region 1: I/O ports at 03f4 [size=1]
	Region 2: I/O ports at 0170 [size=8]
	Region 3: I/O ports at 0374 [size=1]
	Region 4: I/O ports at bfa0 [size=16]
	Capabilities: <access denied>
	Kernel driver in use: ata_piix
	Kernel modules: ata_piix

00:1f.3 SMBus [0c05]: Intel Corporation 82801G (ICH7 Family) SMBus Controller [8086:27da] (rev 01)
	Subsystem: Dell Device [1028:01cc]
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin B routed to IRQ 17
	Region 4: I/O ports at 10c0 [size=32]
	Kernel driver in use: i801_smbus
	Kernel modules: i2c-i801

01:00.0 VGA compatible controller [0300]: nVidia Corporation G72M [Quadro NVS 110M/GeForce Go 7300] [10de:01d7] (rev a1) (prog-if 00 [VGA controller])
	Subsystem: Dell Device [1028:01cc]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at ed000000 (32-bit, non-prefetchable) [size=16M]
	Region 1: Memory at d0000000 (64-bit, prefetchable) [size=256M]
	Region 3: Memory at ee000000 (64-bit, non-prefetchable) [size=16M]
	[virtual] Expansion ROM at ef000000 [disabled] [size=128K]
	Capabilities: <access denied>
	Kernel driver in use: nvidia
	Kernel modules: nvidiafb, nvidia

03:01.0 CardBus bridge [0607]: O2 Micro, Inc. Cardbus bridge [1217:7135] (rev 21)
	Subsystem: Dell Device [1028:01cc]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 168
	Interrupt: pin A routed to IRQ 19
	Region 0: Memory at ecb00000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=03, secondary=04, subordinate=07, sec-latency=176
	Memory window 0: e0400000-e07ff000 (prefetchable)
	Memory window 1: e4000000-e7fff000
	I/O window 0: 00002000-000020ff
	I/O window 1: 00002400-000024ff
	BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
	16-bit legacy interface ports at 0001
	Kernel driver in use: yenta_cardbus
	Kernel modules: yenta_socket

03:01.4 FireWire (IEEE 1394) [0c00]: O2 Micro, Inc. Firewire (IEEE 1394) [1217:00f7] (rev 02) (prog-if 10 [OHCI])
	Subsystem: Dell Device [1028:01cc]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
	Latency: 64, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 19
	Region 0: Memory at ecbff000 (32-bit, non-prefetchable) [size=4K]
	Region 1: Memory at ecbfe800 (32-bit, non-prefetchable) [size=2K]
	Capabilities: <access denied>
	Kernel driver in use: ohci1394
	Kernel modules: ohci1394

09:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5752 Gigabit Ethernet PCI Express [14e4:1600] (rev 02)
	Subsystem: Dell Device [1028:01cc]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 1274
	Region 0: Memory at ecef0000 (64-bit, non-prefetchable) [size=64K]
	Expansion ROM at <ignored> [disabled]
	Capabilities: <access denied>
	Kernel driver in use: tg3
	Kernel modules: tg3

0c:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection [8086:4222] (rev 02)
	Subsystem: Intel Corporation Device [8086:1021]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 1273
	Region 0: Memory at ecfff000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: <access denied>
	Kernel driver in use: iwl3945
	Kernel modules: iwl3945



-- System Information:
Debian Release: 5.0
  APT prefers stable
  APT policy: (500, 'stable')
Architecture: i386 (x86_64)

Kernel: Linux 2.6.26-1-amd64 (SMP w/2 CPU cores)
Locale: LANG=ru_RU.UTF-8, LC_CTYPE=ru_RU.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash

Versions of packages linux-image-2.6.26-1-amd64 depends on:
ii  debconf [debconf-2.0]         1.5.24     Debian configuration management sy
ii  initramfs-tools [linux-initra 0.92o      tools for generating an initramfs
ii  module-init-tools             3.4-1      tools for managing Linux kernel mo

linux-image-2.6.26-1-amd64 recommends no packages.

Versions of packages linux-image-2.6.26-1-amd64 suggests:
ii  grub                       0.97-47lenny2 GRand Unified Bootloader (Legacy v
pn  linux-doc-2.6.26           <none>        (no description available)

-- debconf information:
  linux-image-2.6.26-1-amd64/preinst/bootloader-initrd-2.6.26-1-amd64: true
  linux-image-2.6.26-1-amd64/postinst/old-initrd-link-2.6.26-1-amd64: true
  linux-image-2.6.26-1-amd64/postinst/old-system-map-link-2.6.26-1-amd64: true
  linux-image-2.6.26-1-amd64/preinst/overwriting-modules-2.6.26-1-amd64: true
  linux-image-2.6.26-1-amd64/preinst/lilo-initrd-2.6.26-1-amd64: true
  linux-image-2.6.26-1-amd64/prerm/removing-running-kernel-2.6.26-1-amd64: true
  linux-image-2.6.26-1-amd64/prerm/would-invalidate-boot-loader-2.6.26-1-amd64: true
  linux-image-2.6.26-1-amd64/postinst/bootloader-test-error-2.6.26-1-amd64:
  linux-image-2.6.26-1-amd64/preinst/lilo-has-ramdisk:
  linux-image-2.6.26-1-amd64/postinst/old-dir-initrd-link-2.6.26-1-amd64: true
  linux-image-2.6.26-1-amd64/preinst/failed-to-move-modules-2.6.26-1-amd64:
  linux-image-2.6.26-1-amd64/postinst/create-kimage-link-2.6.26-1-amd64: true
  shared/kernel-image/really-run-bootloader: true
  linux-image-2.6.26-1-amd64/postinst/kimage-is-a-directory:
  linux-image-2.6.26-1-amd64/preinst/initrd-2.6.26-1-amd64:
  linux-image-2.6.26-1-amd64/postinst/depmod-error-initrd-2.6.26-1-amd64: false
  linux-image-2.6.26-1-amd64/preinst/elilo-initrd-2.6.26-1-amd64: true
  linux-image-2.6.26-1-amd64/postinst/bootloader-error-2.6.26-1-amd64:
  linux-image-2.6.26-1-amd64/preinst/abort-install-2.6.26-1-amd64:
  linux-image-2.6.26-1-amd64/postinst/depmod-error-2.6.26-1-amd64: false
  linux-image-2.6.26-1-amd64/preinst/abort-overwrite-2.6.26-1-amd64:

-- 
wbr, Kirill



--- End Message ---
--- Begin Message ---
On Sat, Feb 20, 2010 at 10:14:05AM +0100, Moritz Muehlenhoff wrote:
> On Sat, Mar 28, 2009 at 11:37:32AM +0100, maximilian attems wrote:
> > can you reproduce that with a more recent linux image like 2.6.29?
> 
> Kirill,
> The next release of Debian (6.0, code name Squeeze) will be based
> on 2.6.32. Please test the current 2.6.32 from unstable/testing and tell
> us whether the problem persists. If so, we should report it upstream
> to the kernel.org developers.
> 
> The 2.6.32 kernel is available from packages.debian.org and can
> be installed in both Debian stable, testing and unstable
> installations.

No further feedback, closing the bug.

If this can be reproduced with current kernels, please reopen this bug.

Cheers,
        Moritz


--- End Message ---

Reply to: