Bug#583390: linux-image-2.6.32-5-686: Hangs with "ata frozen" on boot
[sorry for the noise]
I haven't filed my own bugreport because it's not a big issue for me, ATM.
I'd rather wait the extra minute or so during boot, than change my disk maps and menus...
I have a very similar dmesg.... ata1: lost interrupt (Status 0x58) - and the kernel times out for about (30 seconds on each PATA Channel)
while waiting for dma [on the slave of both PATA channels]...
Both primary and secondary channel masters are hard disks and both primary and seconardy slaves are DVD burners...
The primary PATA channel slave is initialized at 33mbs
and the secondary channel slave is initialzed at 25mbs on the bus..
I saw this behavior "once" before while testing the last pre-release of the d-i just before Lenny was released. I worked around the issue at that time by fiddling with (ATA/IDE Configuration - enhanced/legacy SATA/PATA) and onboard (SATA RAID) BIOS settings...
Before sending this I
Unplugged both DVD burners, rebooted
Double checked disk jumpers, rebooted.
Disabled BIOS setting "PCI ATA Bus Master" rebooted
Installed 2.6.34-1-686, rebooted
Disabled "ATA/IDE Configuration" BIOS setting, rebooted
Changing BIOS setting:
Drive Configuration ->
ATA/IDE Configuration (Legacy) ->
Legacy IDE Channels (SATA PO/P1 only)
gets rid of the kernel timeout
but no longer initializes any of the PATA Channels
Intel D865PERLK mobo - 2 SATA channels - first generation
All disk channels populated.
--- On Thu, 5/27/10, Adrian Lang <debian@adrianlang.de> wrote:
> From: Adrian Lang <debian@adrianlang.de>
> Subject: Bug#583390: linux-image-2.6.32-5-686: Hangs with "ata frozen" on boot
> To: "Debian Bug Tracking System" <submit@bugs.debian.org>
> Date: Thursday, May 27, 2010, 10:44 AM
> Package: linux-2.6
> Version: 2.6.32-13
> Severity: important
> Tags: sid
>
> After "Loading, please wait...", linux hangs for 30
> seconds. after that, it logs:
> ----
> ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
> frozen
> ata1.00: cmd a0/01:00:00:80:00/00:00:00:00:00/a0 tag 0 dma
> 16512 in
> res
> 40/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
> ata1.00: status: { DRDY }
> ----
> These messages are repeated after 40 seconds, and again 40
> seconds.
>
> linux-image-2.6.32-3-686 works, linux-image-2.6.33-2-686
> and linux-image-2.6.34-1-686 show the same behaviour.
>
> -- Package-specific info:
> ** Kernel log: boot messages should be attached
>
> ** Model information
> not available
>
> ** PCI devices:
> 00:00.0 Host bridge [0600]: Intel Corporation
> 82G33/G31/P35/P31 Express DRAM Controller [8086:29c0] (rev
> 10)
> Subsystem: ASUSTeK Computer Inc.
> P5KPL-VM Motherboard [1043:82b0]
> Control: I/O- Mem+ BusMaster+ SpecCycle-
> MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B+
> ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+
> >SERR- <PERR- INTx-
> Latency: 0
> Capabilities: <access denied>
>
> 00:01.0 PCI bridge [0604]: Intel Corporation
> 82G33/G31/P35/P31 Express PCI Express Root Port [8086:29c1]
> (rev 10) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle-
> MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
> DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B-
> ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort-
> >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Bus: primary=00, secondary=01,
> subordinate=01, sec-latency=0
> Memory behind bridge: fc000000-fe9fffff
> Prefetchable memory behind bridge:
> 00000000e0000000-00000000efffffff
> Secondary status: 66MHz- FastB2B-
> ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+
> <SERR- <PERR-
> BridgeCtl: Parity- SERR+ NoISA- VGA+
> MAbort- >Reset- FastB2B-
> PriDiscTmr-
> SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: <access denied>
> Kernel driver in use: pcieport
>
> 00:1b.0 Audio device [0403]: Intel Corporation N10/ICH 7
> Family High Definition Audio Controller [8086:27d8] (rev
> 01)
> Subsystem: ASUSTeK Computer Inc.
> P5KPL-VM Motherboard [1043:8290]
> Control: I/O- Mem+ BusMaster+ SpecCycle-
> MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B-
> ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort-
> >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 16
> Region 0: Memory at fbffc000 (64-bit,
> non-prefetchable) [size=16K]
> Capabilities: <access denied>
> Kernel driver in use: HDA Intel
>
> 00:1c.0 PCI bridge [0604]: Intel Corporation N10/ICH 7
> Family PCI Express Port 1 [8086:27d0] (rev 01) (prog-if 00
> [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle-
> MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
> DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B-
> ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort-
> >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Bus: primary=00, secondary=03,
> subordinate=03, sec-latency=0
> I/O behind bridge: 00001000-00001fff
> Memory behind bridge: 80000000-801fffff
> Prefetchable memory behind bridge:
> 0000000080200000-00000000803fffff
> Secondary status: 66MHz- FastB2B-
> ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort-
> <SERR- <PERR-
> BridgeCtl: Parity- SERR+ NoISA- VGA-
> MAbort- >Reset- FastB2B-
> PriDiscTmr-
> SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: <access denied>
> Kernel driver in use: pcieport
>
> 00:1c.1 PCI bridge [0604]: Intel Corporation N10/ICH 7
> Family PCI Express Port 2 [8086:27d2] (rev 01) (prog-if 00
> [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle-
> MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
> DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B-
> ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort-
> >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Bus: primary=00, secondary=02,
> subordinate=02, sec-latency=0
> I/O behind bridge: 0000d000-0000dfff
> Memory behind bridge: fea00000-feafffff
> Prefetchable memory behind bridge:
> 00000000faf00000-00000000faffffff
> Secondary status: 66MHz- FastB2B-
> ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort-
> <SERR- <PERR-
> BridgeCtl: Parity- SERR+ NoISA- VGA-
> MAbort- >Reset- FastB2B-
> PriDiscTmr-
> SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: <access denied>
> Kernel driver in use: pcieport
>
> 00:1d.0 USB Controller [0c03]: Intel Corporation N10/ICH7
> Family USB UHCI Controller #1 [8086:27c8] (rev 01) (prog-if
> 00 [UHCI])
> Subsystem: ASUSTeK Computer Inc.
> P5KPL-VM,P5LD2-VM Mainboard [1043:8179]
> Control: I/O+ Mem- BusMaster+ SpecCycle-
> MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B+
> ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort-
> >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin A routed to IRQ 23
> Region 4: I/O ports at c480 [size=32]
> Kernel driver in use: uhci_hcd
>
> 00:1d.1 USB Controller [0c03]: Intel Corporation N10/ICH 7
> Family USB UHCI Controller #2 [8086:27c9] (rev 01) (prog-if
> 00 [UHCI])
> Subsystem: ASUSTeK Computer Inc.
> P5KPL-VM,P5LD2-VM Mainboard [1043:8179]
> Control: I/O+ Mem- BusMaster+ SpecCycle-
> MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B+
> ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort-
> >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin B routed to IRQ 19
> Region 4: I/O ports at c800 [size=32]
> Kernel driver in use: uhci_hcd
>
> 00:1d.2 USB Controller [0c03]: Intel Corporation N10/ICH 7
> Family USB UHCI Controller #3 [8086:27ca] (rev 01) (prog-if
> 00 [UHCI])
> Subsystem: ASUSTeK Computer Inc.
> P5KPL-VM,P5LD2-VM Mainboard [1043:8179]
> Control: I/O+ Mem- BusMaster+ SpecCycle-
> MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B+
> ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort-
> >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin C routed to IRQ 18
> Region 4: I/O ports at c880 [size=32]
> Kernel driver in use: uhci_hcd
>
> 00:1d.3 USB Controller [0c03]: Intel Corporation N10/ICH 7
> Family USB UHCI Controller #4 [8086:27cb] (rev 01) (prog-if
> 00 [UHCI])
> Subsystem: ASUSTeK Computer Inc.
> P5KPL-VM,P5LD2-VM Mainboard [1043:8179]
> Control: I/O+ Mem- BusMaster+ SpecCycle-
> MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B+
> ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort-
> >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin D routed to IRQ 16
> Region 4: I/O ports at cc00 [size=32]
> Kernel driver in use: uhci_hcd
>
> 00:1d.7 USB Controller [0c03]: Intel Corporation N10/ICH 7
> Family USB2 EHCI Controller [8086:27cc] (rev 01) (prog-if 20
> [EHCI])
> Subsystem: ASUSTeK Computer Inc.
> P5KPL-VM,P5LD2-VM Mainboard [1043:8179]
> Control: I/O- Mem+ BusMaster+ SpecCycle-
> MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B+
> ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort-
> >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin A routed to IRQ 23
> Region 0: Memory at fbffbc00 (32-bit,
> non-prefetchable) [size=1K]
> Capabilities: <access denied>
> Kernel driver in use: ehci_hcd
>
> 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI
> Bridge [8086:244e] (rev e1) (prog-if 01 [Subtractive
> decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle-
> MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
> DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B-
> ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort-
> >SERR- <PERR- INTx-
> Latency: 0
> Bus: primary=00, secondary=04,
> subordinate=04, sec-latency=32
> I/O behind bridge: 0000e000-0000efff
> Memory behind bridge: feb00000-febfffff
> Prefetchable memory behind bridge:
> 0000000080400000-00000000804fffff
> Secondary status: 66MHz- FastB2B+
> ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+
> <SERR- <PERR-
> BridgeCtl: Parity- SERR+ NoISA- VGA-
> MAbort- >Reset- FastB2B-
> PriDiscTmr-
> SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: <access denied>
>
> 00:1f.0 ISA bridge [0601]: Intel Corporation 82801GB/GR
> (ICH7 Family) LPC Interface Bridge [8086:27b8] (rev 01)
> Subsystem: ASUSTeK Computer Inc.
> P5KPL-VM Motherboard [1043:8179]
> Control: I/O+ Mem+ BusMaster+ SpecCycle-
> MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B-
> ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort-
> >SERR- <PERR- INTx-
> Latency: 0
> Capabilities: <access denied>
>
> 00:1f.1 IDE interface [0101]: Intel Corporation 82801G
> (ICH7 Family) IDE Controller [8086:27df] (rev 01) (prog-if
> 8a [Master SecP PriP])
> Subsystem: ASUSTeK Computer Inc.
> P5KPL-VM Motherboard [1043:8179]
> Control: I/O+ Mem- BusMaster+ SpecCycle-
> MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B+
> ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort-
> >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin A routed to IRQ 18
> Region 0: I/O ports at 01f0 [size=8]
> Region 1: I/O ports at 03f4 [size=1]
> Region 2: I/O ports at 0170 [size=8]
> Region 3: I/O ports at 0374 [size=1]
> Region 4: I/O ports at ffa0 [size=16]
> Kernel driver in use: PIIX_IDE
>
> 00:1f.2 IDE interface [0101]: Intel Corporation N10/ICH7
> Family SATA IDE Controller [8086:27c0] (rev 01) (prog-if 8f
> [Master SecP SecO PriP PriO])
> Subsystem: ASUSTeK Computer Inc.
> P5KPL-VM Motherboard [1043:8179]
> Control: I/O+ Mem- BusMaster+ SpecCycle-
> MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B+
> ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort-
> >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin B routed to IRQ 19
> Region 0: I/O ports at c400 [size=8]
> Region 1: I/O ports at c080 [size=4]
> Region 2: I/O ports at c000 [size=8]
> Region 3: I/O ports at bc00 [size=4]
> Region 4: I/O ports at b880 [size=16]
> Capabilities: <access denied>
> Kernel driver in use: ata_piix
>
> 00:1f.3 SMBus [0c05]: Intel Corporation N10/ICH 7 Family
> SMBus Controller [8086:27da] (rev 01)
> Subsystem: ASUSTeK Computer Inc.
> P5KPL-VM Motherboard [1043:8179]
> Control: I/O+ Mem- BusMaster- SpecCycle-
> MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B+
> ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort-
> >SERR- <PERR- INTx-
> Interrupt: pin B routed to IRQ 19
> Region 4: I/O ports at 0400 [size=32]
> Kernel driver in use: i801_smbus
>
> 01:00.0 VGA compatible controller [0300]: nVidia
> Corporation G71 [GeForce 7300 GS] [10de:01df] (rev a1)
> (prog-if 00 [VGA controller])
> Subsystem: Micro-Star International Co.,
> Ltd. Device [1462:0345]
> Control: I/O+ Mem+ BusMaster+ SpecCycle-
> MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B-
> ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort-
> >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin A routed to IRQ 16
> Region 0: Memory at fd000000 (32-bit,
> non-prefetchable) [size=16M]
> Region 1: Memory at e0000000 (64-bit,
> prefetchable) [size=256M]
> Region 3: Memory at fc000000 (64-bit,
> non-prefetchable) [size=16M]
> [virtual] Expansion ROM at fe9e0000
> [disabled] [size=128K]
> Capabilities: <access denied>
> Kernel driver in use: nvidia
>
> 02:00.0 Ethernet controller [0200]: Realtek Semiconductor
> Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet
> controller [10ec:8168] (rev 02)
> Subsystem: ASUSTeK Computer Inc. Device
> [1043:82c6]
> Control: I/O+ Mem+ BusMaster+ SpecCycle-
> MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B-
> ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort-
> >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 27
> Region 0: I/O ports at d800 [size=256]
> Region 2: Memory at fafff000 (64-bit,
> prefetchable) [size=4K]
> Region 4: Memory at fafe0000 (64-bit,
> prefetchable) [size=64K]
> Expansion ROM at feaf0000 [disabled]
> [size=64K]
> Capabilities: <access denied>
> Kernel driver in use: r8169
>
> 04:00.0 Ethernet controller [0200]: 3Com Corporation 3c905B
> 100BaseTX [Cyclone] [10b7:9055] (rev 30)
> Subsystem: 3Com Corporation 3C905B Fast
> Etherlink XL 10/100 [10b7:9055]
> Control: I/O+ Mem+ BusMaster+ SpecCycle-
> MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
> DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B-
> ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort-
> >SERR- <PERR- INTx-
> Latency: 64 (2500ns min, 2500ns max),
> Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 19
> Region 0: I/O ports at ec00 [size=128]
> Region 1: Memory at febffc00 (32-bit,
> non-prefetchable) [size=128]
> Expansion ROM at 80400000 [disabled]
> [size=128K]
> Capabilities: <access denied>
> Kernel driver in use: 3c59x
>
>
> ** USB devices:
> Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root
> hub
> Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root
> hub
> Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root
> hub
> Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root
> hub
> Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root
> hub
>
>
> -- System Information:
> Debian Release: squeeze/sid
> APT prefers testing
> APT policy: (990, 'testing'), (500, 'unstable'),
> (500, 'stable'), (1, 'experimental')
> Architecture: i386 (i686)
>
> Kernel: Linux 2.6.32-3-686 (SMP w/2 CPU cores)
> Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8
> (charmap=UTF-8)
> Shell: /bin/sh linked to /bin/dash
>
> Versions of packages linux-image-2.6.32-5-686 depends on:
> ii debconf [debconf 1.5.32
> Debian configuration
> management sy
> ii initramfs-tools 0.94.4
> tools for
> generating an initramfs
> ii linux-base
> 2.6.34-1~experimental.1 Linux image base
> package
> ii module-init-tool 3.12~pre2-3
> tools for managing Linux
> kernel mo
>
> Versions of packages linux-image-2.6.32-5-686 recommends:
> pn firmware-linux-free
> <none> (no
> description available)
> ii libc6-i686
>
> 2.10.2-9 GNU C Library: Shared libraries
> [i
>
> Versions of packages linux-image-2.6.32-5-686 suggests:
> pn grub | lilo
> <none>
> (no description available)
> pn linux-doc-2.6.32
> <none> (no
> description available)
>
> Versions of packages linux-image-2.6.32-5-686 is related
> to:
> pn firmware-bnx2
> <none>
> (no description available)
> pn firmware-bnx2x
> <none>
> (no description available)
> pn firmware-ipw2x00
> <none> (no
> description available)
> pn firmware-ivtv
> <none>
> (no description available)
> pn firmware-iwlwifi
> <none> (no
> description available)
> pn firmware-linux
> <none>
> (no description available)
> pn firmware-linux-nonfree
> <none> (no description
> available)
> pn firmware-qlogic
> <none>
> (no description available)
> pn firmware-ralink
> <none>
> (no description available)
> pn xen-hypervisor
> <none>
> (no description available)
>
> -- debconf information:
> shared/kernel-image/really-run-bootloader: true
>
> linux-image-2.6.32-5-686/prerm/removing-running-kernel-2.6.32-5-686:
> true
>
> linux-image-2.6.32-5-686/prerm/would-invalidate-boot-loader-2.6.32-5-686:
> true
>
> linux-image-2.6.32-5-686/postinst/bootloader-test-error-2.6.32-5-686:
>
> linux-image-2.6.32-5-686/postinst/bootloader-error-2.6.32-5-686:
>
> linux-image-2.6.32-5-686/postinst/depmod-error-initrd-2.6.32-5-686:
> false
>
> linux-image-2.6.32-5-686/postinst/missing-firmware-2.6.32-5-686:
>
>
>
> --
> To UNSUBSCRIBE, email to debian-kernel-REQUEST@lists.debian.org
> with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
> Archive: [🔎] 20100527144412.8983.75605.reportbug@tonks.cosmo">http://lists.debian.org/[🔎] 20100527144412.8983.75605.reportbug@tonks.cosmo
>
>
Reply to: