[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Bug#580149: linux-image-2.6.32-trunk-amd64: usb - sata > Sense not available



> Looking back at the original error messages, it looks like the cable
> might be sub-standard and not suitable for USB High Speed.  Can you try
> changing the cable?


looks like the converter

|-------------- |
| usb-sata   |
|	             ||=====> to usb port on pci card(there is no cable)
| converter   |
|---------------|
     | |
     | |
     | |
     V
     sata cable to hdd.



The motherboard USB port is operating normally, but the PCI card gives an error.



debug contents :
----------------------------------------
usb-storage 2-3:1.0: usb_probe_interface
usb-storage 2-3:1.0: usb_probe_interface - got id
usb-storage: USB Mass Storage device detected
usb-storage: -- associate_dev
usb-storage: Vendor: 0x152d, Product: 0x2329, Revision: 0x0100
usb-storage: Interface Subclass: 0x06, Protocol: 0x50
usb-storage: Transport: Bulk
usb-storage: Protocol: Transparent SCSI
usb-storage: *** thread sleeping.
.
..
...............Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x1 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad LUN (0:1)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (1:0)
..
...
Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries
ehci_hcd 0000:04:01.2: detected XactErr len 0/4096 retry 1
ehci_hcd 0000:04:01.2: detected XactErr len 0/4096 retry 2
ehci_hcd 0000:04:01.2: detected XactErr len 0/4096 retry 3
ehci_hcd 0000:04:01.2: detected XactErr len 0/4096 retry 4
ehci_hcd 0000:04:01.2: detected XactErr len 0/4096 retry 5
ehci_hcd 0000:04:01.2: detected XactErr len 0/4096 retry 6
.............................................................


on Motherboard usb port(work fine) : 

usb 1-2: new high speed USB device using ehci_hcd and address 2
usb 1-2: New USB device found, idVendor=152d, idProduct=2329
usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=5
usb 1-2: Product: USB to ATA/ATAPI Bridge
usb 1-2: Manufacturer: JMicron
usb 1-2: SerialNumber: 08871F418665
scsi2 : usb-storage 1-2:1.0
scsi 2:0:0:0: Direct-Access     SAMSUNG  SP1213C               PQ: 0 ANSI: 2 CCS
sd 2:0:0:0: [sdb] 234493056 512-byte logical blocks: (120 GB/111 GiB)
sd 2:0:0:0: [sdb] Write Protect is off
sdb:
sdb1
sd 2:0:0:0: [sdb] Attached SCSI disk


Best wishes
hz



Reply to: