Bug#581340: linux-image-2.6.32-3-amd64: Kernel panic or hardware shutdown on HP ProLiant ML370 G6
Package: linux-image-2.6.32-3-amd64
Version: 2.6.32-9
Severity: important
Tags: squeeze
*** Please type your report below this line ***
When i bring up network interface eth1-eth3 i see messages from kernel
like this:
Message from syslogd@localhost at Apr 2 09:29:57 ... kernel:[
227.352979] Uhhuh. NMI received for unknown reason b1 on CPU 0.
Message from syslogd@localhost at Apr 2 09:29:57 ... kernel:[
227.353044] You have some hardware problem, likely on the PCI bus.
Message from syslogd@localhost at Apr 2 09:29:57 ... kernel:[
227.353106] Dazed and confused, but trying to continue
and my network card become unavaible. Sometimes I see kernel panic
message instead of this.
When I use only interface eth0 after some hours I see kernel message:
[121030.457885] eth0: Device temperature 100 degrees C exceeds maximum
allowed. Hardware has been shut down.
[121030.457939] eth1: Device temperature 100 degrees C exceeds maximum
allowed. Hardware has been shut down.
[121030.457990] eth2: Device temperature 100 degrees C exceeds maximum
allowed. Hardware has been shut down.
[121062.437873] netxen_nic: card response timeout.
[121062.437902] netxen_nic: Failed to destroy rx ctx in firmware
[121094.417869] netxen_nic: card response timeout.
[121094.417898] netxen_nic: Failed to destroy tx ctx in firmware
[121094.460703] eth3: Device temperature 100 degrees C exceeds maximum
allowed. Hardware has been shut down.
But I am sure that this temerature can't exist.
And after this error network card doesn't work too.
I can not tell exaclty what kind of network card is used, but I can
say that server which is used is HP ProLiant ML370 G6.
$ lspci -vs 06:00.0
06:00.0 Ethernet controller: NetXen Incorporated NX3031 Multifunction
1/10-Gigabit Server Adapter (rev 42)
Subsystem: Hewlett-Packard Company NC375i Integrated Quad Port
Multifunction Gigabit Server Adapter
Flags: bus master, fast devsel, latency 0, IRQ 24
Memory at fae00000 (64-bit, non-prefetchable) [size=2M]
Memory at f8000000 (64-bit, non-prefetchable) [size=32M]
Capabilities: <access denied>
Kernel driver in use: netxen_nic
Kernel modules: netxen_nic
$ dmesg |grep eth
[ 1.796876] ACPI Error (psparse-0537): Method parse/execution
failed [\_SB_._OSC] (Node ffff880426c14f20), AE_AML_BUFFER_LIMIT
[ 2.432767] netxen_nic 0000:06:00.0: eth0: GbE port initialized
[ 2.434177] netxen_nic 0000:06:00.1: eth1: GbE port initialized
[ 2.435628] netxen_nic 0000:06:00.2: eth2: GbE port initialized
[ 2.437115] netxen_nic 0000:06:00.3: eth3: GbE port initialized
[ 8.754656] netxen_nic: eth0 NIC Link is up
[ 8.755739] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 8.760126] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 19.319590] eth0: no IPv6 routers present
I'm not sure that I rightly specify the package for this bugreport. I
had made a mistake (
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=579212 ) and send a
report to the wrong place. Please let me know about correct place for
this report if I am wrong again.
As in lenny network card is not working, I have updated debian to
squeeze and periodically perform full upgrade hoping that the problem
will be fixed soon. The kernel is also being updated. That is why I do
not think that the problem exists only for the specified kernel
version.
I have not tested whether there is a problem in other linux distributions.
-- Package-specific info:
** Version:
Linux version 2.6.32-3-amd64 (Debian 2.6.32-9) (maks@debian.org) (gcc
version 4.3.4 (Debian 4.3.4-8) ) #1 SMP Wed Feb 24 18:07:42 UTC 2010
** Command line:
BOOT_IMAGE=/boot/vmlinuz-2.6.32-3-amd64
root=UUID=6d33a63d-3cee-4a57-9fc5-bb72dab917c3 ro quiet
** Not tainted
** Kernel log:
[ 2.428149] uhci_hcd 0000:01:04.4: new USB bus registered, assigned
bus number 6
[ 2.428163] uhci_hcd 0000:01:04.4: port count misdetected? forcing to 2 ports
[ 2.428836] uhci_hcd 0000:01:04.4: irq 22, io base 0x00003800
[ 2.428933] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.428936] usb usb6: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 2.428939] usb usb6: Product: UHCI Host Controller
[ 2.428941] usb usb6: Manufacturer: Linux 2.6.32-3-amd64 uhci_hcd
[ 2.429031] usb usb6: SerialNumber: 0000:01:04.4
[ 2.429091] usb usb6: configuration #1 chosen from 1 choice
[ 2.429115] netxen_nic 0000:06:00.3: eth3: GbE port initialized
[ 2.429131] hub 6-0:1.0: USB hub found
[ 2.429137] hub 6-0:1.0: 2 ports detected
[ 2.738440] usb 6-1: new full speed USB device using uhci_hcd and address 2
[ 2.757180] ata1: SATA link down (SStatus 4 SControl 300)
[ 2.757191] ata1.00: link status unknown, clearing UNKNOWN to NONE
[ 2.757223] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2.757233] ata2.00: link online but device misclassifed
[ 2.757236] ata2: link online but 1 devices misclassified, retrying
[ 2.757239] ata2: reset failed (errno=-11), retrying in 10 secs
[ 2.885611] usb 6-1: New USB device found, idVendor=03f0, idProduct=1027
[ 2.885614] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.885617] usb 6-1: Product: Virtual Keyboard
[ 2.885619] usb 6-1: Manufacturer: HP
[ 2.885695] usb 6-1: configuration #1 chosen from 1 choice
[ 2.902444] usbcore: registered new interface driver hiddev
[ 2.906490] input: HP Virtual Keyboard as
/devices/pci0000:00/0000:00:1e.0/0000:01:04.4/usb6/6-1/6-1:1.0/input/input3
[ 2.906545] generic-usb 0003:03F0:1027.0001: input,hidraw0: USB HID
v1.01 Keyboard [HP Virtual Keyboard] on usb-0000:01:04.4-1/input0
[ 2.912970] input: HP Virtual Keyboard as
/devices/pci0000:00/0000:00:1e.0/0000:01:04.4/usb6/6-1/6-1:1.1/input/input4
[ 2.913029] generic-usb 0003:03F0:1027.0002: input,hidraw1: USB HID
v1.01 Mouse [HP Virtual Keyboard] on usb-0000:01:04.4-1/input1
[ 2.913050] usbcore: registered new interface driver usbhid
[ 2.913053] usbhid: v2.6:USB HID core driver
[ 12.895159] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 12.903380] ata2.00: ATAPI: hp DVDROM DH20N, EB00, max UDMA/100
[ 12.919377] ata2.00: configured for UDMA/100
[ 12.920922] scsi 1:0:0:0: CD-ROM hp DVDROM DH20N
EB00 PQ: 0 ANSI: 5
[ 12.932315] Uniform Multi-Platform E-IDE driver
[ 12.942729] sr0: scsi3-mmc drive: 12x/40x cd/rw xa/form2 cdda tray
[ 12.942734] Uniform CD-ROM driver Revision: 3.20
[ 12.942825] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 12.946231] sr 1:0:0:0: Attached scsi generic sg0 type 5
[ 13.024461] PM: Starting manual resume from disk
[ 13.024465] PM: Resume from partition 104:5
[ 13.024467] PM: Checking hibernation image.
[ 13.025036] PM: Error -22 checking image file
[ 13.025038] PM: Resume from disk failed.
[ 13.053091] kjournald starting. Commit interval 5 seconds
[ 13.053098] EXT3-fs: mounted filesystem with ordered data mode.
[ 14.293039] udev: starting version 151
[ 14.570027] Monitor-Mwait will be used to enter C-1 state
[ 14.579408] Monitor-Mwait will be used to enter C-3 state
[ 14.583130] input: PC Speaker as /devices/platform/pcspkr/input/input5
[ 14.584373] Monitor-Mwait will be used to enter C-3 state
[ 14.584478] processor LNXCPU:00: registered as cooling_device0
[ 14.646962] power_meter ACPI000D:00: Found ACPI power meter.
[ 14.647007] power_meter ACPI000D:00: Ignoring unsafe software power cap!
[ 14.647645] alloc irq_desc for 21 on node -1
[ 14.647650] alloc kstat_irqs on node -1
[ 14.647659] alloc irq_2_iommu on node -1
[ 14.647671] hpwdt 0000:01:04.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[ 14.647747] hpwdt: New timer passed in is 30 seconds.
[ 14.648141] hp Watchdog Timer Driver: 1.1.1, timer margin: 30
seconds (nowayout=0), allow kernel dump: OFF (default = 0/OFF),
priority: LAST (default = 0/LAST).
[ 14.654420] processor LNXCPU:01: registered as cooling_device1
[ 14.674122] processor LNXCPU:02: registered as cooling_device2
[ 14.677296] processor LNXCPU:03: registered as cooling_device3
[ 14.691449] processor LNXCPU:04: registered as cooling_device4
[ 14.694202] processor LNXCPU:05: registered as cooling_device5
[ 14.694791] processor LNXCPU:06: registered as cooling_device6
[ 14.695403] processor LNXCPU:07: registered as cooling_device7
[ 14.696038] processor LNXCPU:08: registered as cooling_device8
[ 14.696706] processor LNXCPU:09: registered as cooling_device9
[ 14.700218] processor LNXCPU:0a: registered as cooling_device10
[ 14.700879] processor LNXCPU:0b: registered as cooling_device11
[ 14.701450] processor LNXCPU:0c: registered as cooling_device12
[ 14.702102] processor LNXCPU:0d: registered as cooling_device13
[ 14.702651] processor LNXCPU:0e: registered as cooling_device14
[ 14.703325] processor LNXCPU:0f: registered as cooling_device15
[ 14.745389] ipmi message handler version 39.2
[ 14.758791] IPMI System Interface driver.
[ 14.758794] ipmi_si: Trying SMBIOS-specified kcs state machine at
i/o address 0xca2, slave address 0x20, irq 0
[ 14.847976] Error: Driver 'pcspkr' is already registered, aborting...
[ 14.868560] hpilo 0000:01:04.2: PCI INT B -> GSI 22 (level, low) -> IRQ 22
[ 14.934853] ipmi: Found new BMC (man_id: 0x00000b, prod_id:
0x0000, dev_id: 0x11)
[ 14.934862] IPMI kcs interface initialized
[ 14.934873] ipmi_si: Trying ACPI-specified kcs state machine at i/o
address 0xca2, slave address 0x0, irq 0
[ 14.934875] ipmi_si: duplicate interface
[ 14.973828] ipmi_si 0000:01:04.6: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[ 14.973833] ipmi_si: Trying PCI-specified kcs state machine at mem
address 0xeb9f0000, slave address 0x0, irq 21
[ 15.093716] IRQ 21/ipmi_si: IRQF_DISABLED is not guaranteed on shared IRQs
[ 15.093735] Using irq 21
[ 15.245115] input: ImPS/2 Generic Wheel Mouse as
/devices/platform/i8042/serio1/input/input6
[ 15.286023] ipmi: interfacing existing BMC (man_id: 0x00000b,
prod_id: 0x0000, dev_id: 0x11)
[ 15.286038] IPMI kcs interface initialized
[ 15.753765] Adding 48235120k swap on /dev/cciss/c0d0p5.
Priority:-1 extents:1 across:48235120k
[ 15.889390] EXT3 FS on cciss/c0d0p1, internal journal
[ 16.070580] loop: module loaded
[ 17.745718] netxen_nic: eth0 NIC Link is up
[ 17.746588] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 17.749113] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 28.272120] eth0: no IPv6 routers present
[ 137.387634] udev: starting version 153
** Model information
sys_vendor: HP
product_name: ProLiant ML370 G6
product_version:
chassis_vendor: HP
chassis_version:
bios_vendor: HP
bios_version: P63
** Loaded modules:
Module Size Used by
loop 11783 0
bnx2 57289 0
hpilo 6284 0
container 2389 0
snd_pcm 60615 0
snd_timer 15502 1 snd_pcm
snd 46350 2 snd_pcm,snd_timer
soundcore 4598 1 snd
snd_page_alloc 6217 1 snd_pcm
ipmi_si 30912 0
ipmi_msghandler 26506 1 ipmi_si
hpwdt 4916 0
power_meter 8302 0
psmouse 49505 0
serio_raw 3752 0
pcspkr 1699 0
evdev 7336 3
processor 30215 16
ext3 106486 1
jbd 37053 1 ext3
mbcache 4970 1 ext3
sg 18728 0
sr_mod 12602 0
cdrom 29399 1 sr_mod
ide_pci_generic 2788 0
ide_core 76850 1 ide_pci_generic
ata_generic 2983 0
usbhid 33132 0
hid 62825 1 usbhid
uhci_hcd 18505 0
cciss 83334 3
ata_piix 19773 0
ehci_hcd 30706 0
libata 132183 2 ata_generic,ata_piix
usbcore 121703 4 usbhid,uhci_hcd,ehci_hcd
nls_base 6377 1 usbcore
scsi_mod 121925 4 sg,sr_mod,cciss,libata
netxen_nic 72695 0
button 4634 0
thermal 11674 0
fan 3346 0
thermal_sys 11878 3 processor,thermal,fan
** Network interface configuration:
# Used by ifup(8) and ifdown(8). See the interfaces(5) manpage or
# /usr/share/doc/ifupdown/examples for more information.
auto lo
iface lo inet loopback
allow-hotplug eth0
iface eth0 inet static
address 10.2.9.5
netmask 255.255.255.0
network 10.2.9.0
broadcast 10.2.9.255
gateway 10.2.9.1
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
state UP qlen 1000
link/ether 18:a9:05:6e:40:78 brd ff:ff:ff:ff:ff:ff
inet 10.2.9.5/24 brd 10.2.9.255 scope global eth0
inet6 fe80::1aa9:5ff:fe6e:4078/64 scope link
valid_lft forever preferred_lft forever
3: eth1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
link/ether 18:a9:05:6e:40:79 brd ff:ff:ff:ff:ff:ff
4: eth2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
link/ether 18:a9:05:6e:40:7a brd ff:ff:ff:ff:ff:ff
5: eth3: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
link/ether 18:a9:05:6e:40:7b brd ff:ff:ff:ff:ff:ff
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed
multicast|bytes packets errs drop fifo colls carrier compressed
lo: 304 4 0 0 0 0 0 0
304 4 0 0 0 0 0 0
eth0:52713526 36958 0 0 0 0 0 0
1840472 22580 0 0 0 0 0 0
eth1: 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0
eth2: 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0
eth3: 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0
*** Protocol statistics:
Ip:
36404 total packets received
0 forwarded
0 incoming packets discarded
36404 incoming packets delivered
22549 requests sent out
Icmp:
4 ICMP messages received
0 input ICMP message failed.
ICMP input histogram:
destination unreachable: 4
13 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
destination unreachable: 9
echo request: 4
IcmpMsg:
InType3: 4
OutType3: 9
OutType8: 4
Tcp:
132 active connections openings
2 passive connection openings
0 failed connection attempts
0 connection resets received
2 connections established
36153 segments received
22449 segments send out
0 segments retransmited
0 bad segments received.
12 resets sent
Udp:
55 packets received
5 packets to unknown port received.
0 packet receive errors
87 packets sent
UdpLite:
TcpExt:
39 delayed acks sent
3 packets directly queued to recvmsg prequeue.
31067 packet headers predicted
187 acknowledgments not containing data payload received
1197 predicted acknowledgments
2 connections reset due to unexpected data
IpExt:
InMcastPkts: 25
InBcastPkts: 185
InOctets: 51505086
OutOctets: 1522032
InMcastOctets: 700
InBcastOctets: 39502
*** Device features:
eth0: 0x1148b3
eth1: 0x1148b3
eth2: 0x1148b3
eth3: 0x1148b3
lo: 0x13865
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 5520 I/O Hub to ESI Port
[8086:3406] (rev 13)
Subsystem: Hewlett-Packard Company Device [103c:330b]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:01.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI
Express Root Port 1 [8086:3408] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0a, subordinate=0c, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:02.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI
Express Root Port 2 [8086:3409] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=13, subordinate=13, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:03.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI
Express Root Port 3 [8086:340a] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=06, subordinate=08, sec-latency=0
Memory behind bridge: ec000000-faffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:04.0 PCI bridge [0604]: Intel Corporation 5520/X58 I/O Hub PCI
Express Root Port 4 [8086:340b] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=09, subordinate=09, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:05.0 PCI bridge [0604]: Intel Corporation 5520/X58 I/O Hub PCI
Express Root Port 5 [8086:340c] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=10, subordinate=12, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:06.0 PCI bridge [0604]: Intel Corporation 5520/X58 I/O Hub PCI
Express Root Port 6 [8086:340d] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: ebb00000-ebffffff
Prefetchable memory behind bridge: 00000000dc000000-00000000dc0fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:07.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI
Express Root Port 7 [8086:340e] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0d, subordinate=0f, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:08.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI
Express Root Port 8 [8086:340f] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=14, subordinate=14, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:09.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI
Express Root Port 9 [8086:3410] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=15, subordinate=15, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:0a.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI
Express Root Port 10 [8086:3411] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=16, subordinate=16, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:0d.0 Host bridge [0600]: Intel Corporation Device [8086:343a] (rev 13)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:0d.1 Host bridge [0600]: Intel Corporation Device [8086:343b] (rev 13)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:0d.2 Host bridge [0600]: Intel Corporation Device [8086:343c] (rev 13)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:0d.3 Host bridge [0600]: Intel Corporation Device [8086:343d] (rev 13)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:0d.4 Host bridge [0600]: Intel Corporation 5520/5500/X58 Physical
Layer Port 0 [8086:3418] (rev 13)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:0d.5 Host bridge [0600]: Intel Corporation 5520/5500 Physical Layer
Port 1 [8086:3419] (rev 13)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:0d.6 Host bridge [0600]: Intel Corporation Device [8086:341a] (rev 13)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:0e.0 Host bridge [0600]: Intel Corporation Device [8086:341c] (rev 13)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:0e.1 Host bridge [0600]: Intel Corporation Device [8086:341d] (rev 13)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:0e.2 Host bridge [0600]: Intel Corporation Device [8086:341e] (rev 13)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:0e.3 Host bridge [0600]: Intel Corporation Device [8086:341f] (rev 13)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:0e.4 Host bridge [0600]: Intel Corporation Device [8086:3439] (rev 13)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:14.0 PIC [0800]: Intel Corporation 5520/5500/X58 I/O Hub System
Management Registers [8086:342e] (rev 13) (prog-if 00 [8259])
Subsystem: Device [003c:000b]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:14.1 PIC [0800]: Intel Corporation 5520/5500/X58 I/O Hub GPIO and
Scratch Pad Registers [8086:3422] (rev 13) (prog-if 00 [8259])
Subsystem: Device [003c:000b]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:14.2 PIC [0800]: Intel Corporation 5520/5500/X58 I/O Hub Control
Status and RAS Registers [8086:3423] (rev 13) (prog-if 00 [8259])
Subsystem: Device [003c:000b]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:1c.0 PCI bridge [0604]: Intel Corporation 82801JI (ICH10 Family)
PCI Express Root Port 1 [8086:3a40] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=04, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1d.0 USB Controller [0c03]: Intel Corporation 82801JI (ICH10
Family) USB UHCI Controller #1 [8086:3a34] (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:330d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 1000 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801JI (ICH10
Family) USB UHCI Controller #2 [8086:3a35] (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:330d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 23
Region 4: I/O ports at 1020 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 82801JI (ICH10
Family) USB UHCI Controller #3 [8086:3a36] (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:330d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 22
Region 4: I/O ports at 1040 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.3 USB Controller [0c03]: Intel Corporation 82801JI (ICH10
Family) USB UHCI Controller #6 [8086:3a39] (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:330d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 23
Region 4: I/O ports at 1060 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 82801JI (ICH10
Family) USB2 EHCI Controller #1 [8086:3a3a] (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Device [103c:330d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 0: Memory at eb8f0000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge
[8086:244e] (rev 90) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 00002000-00003fff
Memory behind bridge: eb900000-ebafffff
Prefetchable memory behind bridge: 00000000e0000000-00000000e7ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801JIB (ICH10) LPC
Interface Controller [8086:3a18]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel modules: iTCO_wdt
00:1f.5 IDE interface [0101]: Intel Corporation 82801JI (ICH10 Family)
2 port SATA IDE Controller #2 [8086:3a26] (prog-if 85 [Master SecO
PriO])
Subsystem: Hewlett-Packard Company Device [103c:330d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at 10c0 [size=8]
Region 1: I/O ports at 10c8 [size=4]
Region 2: I/O ports at 10d0 [size=8]
Region 3: I/O ports at 10d8 [size=4]
Region 4: I/O ports at 10e0 [size=16]
Region 5: I/O ports at 10f0 [size=16]
Capabilities: <access denied>
Kernel driver in use: ata_piix
Kernel modules: ide-pci-generic, ata_generic, ata_piix
01:03.0 VGA compatible controller [0300]: ATI Technologies Inc ES1000
[1002:515e] (rev 02) (prog-if 00 [VGA controller])
Subsystem: Hewlett-Packard Company Device [103c:31fb]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping+ SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (2000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 7
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 3000 [size=256]
Region 2: Memory at ebaf0000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at eb900000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel modules: radeonfb
01:04.0 System peripheral [0880]: Compaq Computer Corporation
Integrated Lights Out Controller [0e11:b203] (rev 03)
Subsystem: Hewlett-Packard Company Device [103c:3305]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at 2800 [size=256]
Region 1: Memory at ebae0000 (32-bit, non-prefetchable) [size=512]
Capabilities: <access denied>
Kernel driver in use: hpwdt
Kernel modules: hpwdt
01:04.2 System peripheral [0880]: Compaq Computer Corporation
Integrated Lights Out Processor [0e11:b204] (rev 03)
Subsystem: Hewlett-Packard Company Device [103c:3305]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 22
BIST result: 00
Region 0: I/O ports at 3400 [size=256]
Region 1: Memory at ebad0000 (32-bit, non-prefetchable) [size=2K]
Region 2: Memory at ebac0000 (32-bit, non-prefetchable) [size=16K]
Region 3: Memory at eba00000 (32-bit, non-prefetchable) [size=512K]
[virtual] Expansion ROM at eb920000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: hpilo
Kernel modules: hpilo
01:04.4 USB Controller [0c03]: Hewlett-Packard Company Proliant
iLO2/iLO3 virtual USB controller [103c:3300] (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:3305]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin B routed to IRQ 22
Region 4: I/O ports at 3800 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
01:04.6 IPMI SMIC interface [0c07]: Hewlett-Packard Company Proliant
iLO2 virtual UART [103c:3302] (prog-if 01)
Subsystem: Hewlett-Packard Company Device [103c:3305]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 21
Region 0: Memory at eb9f0000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ipmi_si
Kernel modules: ipmi_si
05:00.0 RAID bus controller [0104]: Hewlett-Packard Company Smart
Array G6 controllers [103c:323a] (rev 01)
Subsystem: Hewlett-Packard Company Smart Array P410i [103c:3245]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 27
Region 0: Memory at ebc00000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at ebbf0000 (64-bit, non-prefetchable) [size=4K]
Region 4: I/O ports at 4000 [size=256]
[virtual] Expansion ROM at dc000000 [disabled] [size=512K]
Capabilities: <access denied>
Kernel driver in use: cciss
Kernel modules: cciss
06:00.0 Ethernet controller [0200]: NetXen Incorporated NX3031
Multifunction 1/10-Gigabit Server Adapter [4040:0100] (rev 42)
Subsystem: Hewlett-Packard Company NC375i Integrated Quad Port
Multifunction Gigabit Server Adapter [103c:705a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 24
Region 0: Memory at fae00000 (64-bit, non-prefetchable) [size=2M]
Region 4: Memory at f8000000 (64-bit, non-prefetchable) [size=32M]
Capabilities: <access denied>
Kernel driver in use: netxen_nic
Kernel modules: netxen_nic
06:00.1 Ethernet controller [0200]: NetXen Incorporated NX3031
Multifunction 1/10-Gigabit Server Adapter [4040:0100] (rev 42)
Subsystem: Hewlett-Packard Company NC375i Integrated Quad Port
Multifunction Gigabit Server Adapter [103c:705a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 24
Region 0: Memory at f7e00000 (64-bit, non-prefetchable) [size=2M]
Region 4: Memory at f4000000 (64-bit, non-prefetchable) [size=32M]
Capabilities: <access denied>
Kernel driver in use: netxen_nic
Kernel modules: netxen_nic
06:00.2 Ethernet controller [0200]: NetXen Incorporated NX3031
Multifunction 1/10-Gigabit Server Adapter [4040:0100] (rev 42)
Subsystem: Hewlett-Packard Company NC375i Integrated Quad Port
Multifunction Gigabit Server Adapter [103c:705a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 24
Region 0: Memory at f3e00000 (64-bit, non-prefetchable) [size=2M]
Region 4: Memory at f0000000 (64-bit, non-prefetchable) [size=32M]
Capabilities: <access denied>
Kernel driver in use: netxen_nic
Kernel modules: netxen_nic
06:00.3 Ethernet controller [0200]: NetXen Incorporated NX3031
Multifunction 1/10-Gigabit Server Adapter [4040:0100] (rev 42)
Subsystem: Hewlett-Packard Company NC375i Integrated Quad Port
Multifunction Gigabit Server Adapter [103c:705a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 24
Region 0: Memory at efe00000 (64-bit, non-prefetchable) [size=2M]
Region 4: Memory at ec000000 (64-bit, non-prefetchable) [size=32M]
Capabilities: <access denied>
Kernel driver in use: netxen_nic
Kernel modules: netxen_nic
17:01.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI
Express Root Port 1 [8086:3408] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=17, secondary=18, subordinate=1a, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
17:02.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI
Express Root Port 2 [8086:3409] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=17, secondary=28, subordinate=28, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
17:03.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI
Express Root Port 3 [8086:340a] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=17, secondary=21, subordinate=23, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
17:04.0 PCI bridge [0604]: Intel Corporation 5520/X58 I/O Hub PCI
Express Root Port 4 [8086:340b] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=17, secondary=29, subordinate=29, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
17:05.0 PCI bridge [0604]: Intel Corporation 5520/X58 I/O Hub PCI
Express Root Port 5 [8086:340c] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=17, secondary=2a, subordinate=2a, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
17:06.0 PCI bridge [0604]: Intel Corporation 5520/X58 I/O Hub PCI
Express Root Port 6 [8086:340d] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=17, secondary=2b, subordinate=2b, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
17:07.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI
Express Root Port 7 [8086:340e] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=17, secondary=24, subordinate=26, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
17:08.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI
Express Root Port 8 [8086:340f] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=17, secondary=1e, subordinate=20, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
17:09.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI
Express Root Port 9 [8086:3410] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=17, secondary=1b, subordinate=1d, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
17:0a.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI
Express Root Port 10 [8086:3411] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=17, secondary=2c, subordinate=2c, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
17:0d.0 Host bridge [0600]: Intel Corporation Device [8086:343a] (rev 13)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
17:0d.1 Host bridge [0600]: Intel Corporation Device [8086:343b] (rev 13)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
17:0d.2 Host bridge [0600]: Intel Corporation Device [8086:343c] (rev 13)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
17:0d.3 Host bridge [0600]: Intel Corporation Device [8086:343d] (rev 13)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
17:0d.4 Host bridge [0600]: Intel Corporation 5520/5500/X58 Physical
Layer Port 0 [8086:3418] (rev 13)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
17:0d.5 Host bridge [0600]: Intel Corporation 5520/5500 Physical Layer
Port 1 [8086:3419] (rev 13)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
17:0d.6 Host bridge [0600]: Intel Corporation Device [8086:341a] (rev 13)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
17:0e.0 Host bridge [0600]: Intel Corporation Device [8086:341c] (rev 13)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
17:0e.1 Host bridge [0600]: Intel Corporation Device [8086:341d] (rev 13)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
17:0e.2 Host bridge [0600]: Intel Corporation Device [8086:341e] (rev 13)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
17:0e.3 Host bridge [0600]: Intel Corporation Device [8086:341f] (rev 13)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
17:0e.4 Host bridge [0600]: Intel Corporation Device [8086:3439] (rev 13)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
17:14.0 PIC [0800]: Intel Corporation 5520/5500/X58 I/O Hub System
Management Registers [8086:342e] (rev 13) (prog-if 00 [8259])
Subsystem: Device [003c:000b]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
17:14.1 PIC [0800]: Intel Corporation 5520/5500/X58 I/O Hub GPIO and
Scratch Pad Registers [8086:3422] (rev 13) (prog-if 00 [8259])
Subsystem: Device [003c:000b]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
17:14.2 PIC [0800]: Intel Corporation 5520/5500/X58 I/O Hub Control
Status and RAS Registers [8086:3423] (rev 13) (prog-if 00 [8259])
Subsystem: Device [003c:000b]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
** USB devices:
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 002: ID 03f0:1027 Hewlett-Packard
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: squeeze/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.32-3-amd64 (SMP w/16 CPU cores)
Locale: LANG=ru_RU.UTF-8, LC_CTYPE=ru_RU.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-2.6.32-3-amd64 depends on:
ii debconf [debconf-2.0] 1.5.32 Debian configuration management sy
ii initramfs-tools [linux-initr 0.93.4 tools for generating an initramfs
ii module-init-tools 3.12~pre2-3 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.32-3-amd64 recommends:
pn firmware-linux-free <none> (no description available)
Versions of packages linux-image-2.6.32-3-amd64 suggests:
ii grub 0.97-61 GRand Unified Bootloader (dummy pa
pn linux-doc-2.6.32 <none> (no description available)
Versions of packages linux-image-2.6.32-3-amd64 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-linux <none> (no description available)
pn firmware-linux-nonfree <none> (no description available)
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
-- debconf information:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.32-3-amd64/prerm/removing-running-kernel-2.6.32-3-amd64: true
linux-image-2.6.32-3-amd64/postinst/bootloader-test-error-2.6.32-3-amd64:
linux-image-2.6.32-3-amd64/postinst/missing-firmware-2.6.32-3-amd64:
linux-image-2.6.32-3-amd64/prerm/would-invalidate-boot-loader-2.6.32-3-amd64:
true
linux-image-2.6.32-3-amd64/postinst/depmod-error-initrd-2.6.32-3-amd64: false
linux-image-2.6.32-3-amd64/postinst/bootloader-error-2.6.32-3-amd64:
Reply to: