--- Begin Message ---
- To: Debian Bug Tracking System <submit@bugs.debian.org>
- Subject: linux-image-2.6.30-1-amd64: Player connected as usb storage dowsn't work.
- From: Azraelle Tarien <ptarien@gmail.com>
- Date: Sun, 09 Aug 2009 02:08:30 +0400
- Message-id: <20090808220830.28897.60306.reportbug@shodan.nowhere>
Package: linux-image-2.6.30-1-amd64
Version: 2.6.30-5
Severity: normal
Also tested on .31 form ubuntu. Player model nexx-920.
dmesg log:
[68092.156140] usb 2-1: new high speed USB device using ehci_hcd and address 12
[68092.289037] usb 2-1: New USB device found, idVendor=071b, idProduct=2851
[68092.289049] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[68092.289249] usb 2-1: configuration #1 chosen from 1 choice
[68092.290215] scsi11 : SCSI emulation for USB Mass Storage devices
[68092.291150] usb-storage: device found at 12
[68092.291155] usb-storage: waiting for device to settle before scanning
[68097.288450] usb-storage: device scan complete
[68097.289184] scsi 11:0:0:0: Direct-Access Nexx NF920 1.00 PQ: 0 ANSI: 0
[68097.290022] sd 11:0:0:0: Attached scsi generic sg2 type 0
[68097.292975] sd 11:0:0:0: [sdb] 8214016 512-byte hardware sectors: (4.20 GB/3.91 GiB)
[68097.293467] sd 11:0:0:0: [sdb] Write Protect is off
[68097.293475] sd 11:0:0:0: [sdb] Mode Sense: 00 06 00 00
[68097.293481] sd 11:0:0:0: [sdb] Assuming drive cache: write through
[68097.295583] sd 11:0:0:0: [sdb] Assuming drive cache: write through
[68097.295592] sdb: sdb1
[68097.300064] sd 11:0:0:0: [sdb] Attached SCSI removable disk
[68097.496275] usb 2-1: reset high speed USB device using ehci_hcd and address 12
[68097.760273] usb 2-1: reset high speed USB device using ehci_hcd and address 12
[68098.024236] sd 11:0:0:0: [sdb] Unhandled error code
[68098.024245] sd 11:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[68098.024254] end_request: I/O error, dev sdb, sector 96
[68098.024261] __ratelimit: 40 callbacks suppressed
[68098.024268] Buffer I/O error on device sdb, logical block 12
[68098.024282] Buffer I/O error on device sdb, logical block 13
[68098.024288] Buffer I/O error on device sdb, logical block 14
[68098.024294] Buffer I/O error on device sdb, logical block 15
[68098.024300] Buffer I/O error on device sdb, logical block 16
[68098.024306] Buffer I/O error on device sdb, logical block 17
[68098.024312] Buffer I/O error on device sdb, logical block 18
[68098.024318] Buffer I/O error on device sdb, logical block 19
[68098.024325] Buffer I/O error on device sdb, logical block 20
[68098.024331] Buffer I/O error on device sdb, logical block 21
[68098.024439] sd 11:0:0:0: [sdb] Unhandled error code
[68098.024443] sd 11:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[68098.024450] end_request: I/O error, dev sdb, sector 336
[68098.024527] sd 11:0:0:0: [sdb] Unhandled error code
[68098.024531] sd 11:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[68098.024539] end_request: I/O error, dev sdb, sector 96
[68098.024751] sd 11:0:0:0: [sdb] Unhandled error code
[68098.024756] sd 11:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[68098.024763] end_request: I/O error, dev sdb, sector 96
[68098.024916] sd 11:0:0:0: [sdb] Unhandled error code
[68098.024921] sd 11:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[68098.024928] end_request: I/O error, dev sdb, sector 96
[68098.025072] sd 11:0:0:0: [sdb] Unhandled error code
[68098.025077] sd 11:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[68098.025084] end_request: I/O error, dev sdb, sector 96
[68098.025232] sd 11:0:0:0: [sdb] Unhandled error code
[68098.025237] sd 11:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[68098.025244] end_request: I/O error, dev sdb, sector 96
[68098.025409] sd 11:0:0:0: [sdb] Unhandled error code
[68098.025414] sd 11:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[68098.025421] end_request: I/O error, dev sdb, sector 96
[68098.164121] hub 6-0:1.0: unable to enumerate USB device on port 1
[68098.164149] usb 2-1: USB disconnect, address 12
-- Package-specific info:
** Version:
Linux version 2.6.30-1-amd64 (Debian 2.6.30-5) (maks@debian.org) (gcc version 4.3.3 (Debian 4.3.3-5) ) #1 SMP Mon Aug 3 12:28:22 UTC 2009
** Command line:
root=/dev/sda2 ro
** Tainted: P (1)
** Kernel log:
[68901.888249] usb 6-1: device not accepting address 63, error -71
[68901.888289] hub 6-0:1.0: unable to enumerate USB device on port 1
[68912.400274] usb 6-1: new full speed USB device using uhci_hcd and address 64
[68912.520297] usb 6-1: device descriptor read/64, error -71
[68912.744279] usb 6-1: device descriptor read/64, error -71
[68912.960274] usb 6-1: new full speed USB device using uhci_hcd and address 65
[68913.080039] usb 6-1: device descriptor read/64, error -71
[68913.248156] hub 6-0:1.0: unable to enumerate USB device on port 1
[68914.384276] usb 6-1: new full speed USB device using uhci_hcd and address 66
[68914.504153] usb 6-1: device descriptor read/64, error -71
[68914.728274] usb 6-1: device descriptor read/64, error -71
[68914.888285] hub 6-0:1.0: unable to enumerate USB device on port 1
[68915.376147] usb 6-1: new full speed USB device using uhci_hcd and address 68
[68915.496134] usb 6-1: device descriptor read/64, error -71
[68915.720062] usb 6-1: device descriptor read/64, error -71
[68915.936300] usb 6-1: new full speed USB device using uhci_hcd and address 69
[68916.056271] usb 6-1: device descriptor read/64, error -71
[68916.280286] usb 6-1: device descriptor read/64, error -71
[68916.496299] usb 6-1: new full speed USB device using uhci_hcd and address 70
[68916.904252] usb 6-1: device not accepting address 70, error -71
[68917.016137] usb 6-1: new full speed USB device using uhci_hcd and address 71
[68917.424041] usb 6-1: device not accepting address 71, error -71
[68917.424077] hub 6-0:1.0: unable to enumerate USB device on port 1
[68918.060275] usb 6-1: new full speed USB device using uhci_hcd and address 72
[68918.180297] usb 6-1: device descriptor read/64, error -71
[68918.404275] usb 6-1: device descriptor read/64, error -71
[68918.620077] usb 6-1: new full speed USB device using uhci_hcd and address 73
[68918.740139] usb 6-1: device descriptor read/64, error -71
[68918.964274] usb 6-1: device descriptor read/64, error -71
[68919.180279] usb 6-1: new full speed USB device using uhci_hcd and address 74
[68919.588254] usb 6-1: device not accepting address 74, error -71
[68919.700155] usb 6-1: new full speed USB device using uhci_hcd and address 75
[68920.108256] usb 6-1: device not accepting address 75, error -71
[68920.108295] hub 6-0:1.0: unable to enumerate USB device on port 1
[68938.124301] usb 2-1: new high speed USB device using ehci_hcd and address 24
[68938.257875] usb 2-1: New USB device found, idVendor=0830, idProduct=0061
[68938.257886] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[68938.257893] usb 2-1: Product: palmOne Handheld
[68938.257898] usb 2-1: Manufacturer: palmOne, Inc.
[68938.257902] usb 2-1: SerialNumber: PVG0M5L5V0PM
[68938.258129] usb 2-1: configuration #1 chosen from 1 choice
[68938.797557] usb 2-1: USB disconnect, address 24
[68939.068302] usb 2-1: new high speed USB device using ehci_hcd and address 25
[68939.201789] usb 2-1: New USB device found, idVendor=0830, idProduct=0061
[68939.201801] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[68939.201807] usb 2-1: Product: palmOne Handheld
[68939.201812] usb 2-1: Manufacturer: palmOne, Inc.
[68939.201817] usb 2-1: SerialNumber: PVG0M5L5V0PM
[68939.202020] usb 2-1: configuration #1 chosen from 1 choice
[68939.826931] usb 2-1: USB disconnect, address 25
[68940.424298] usb 6-1: new full speed USB device using uhci_hcd and address 76
[68940.544128] usb 6-1: device descriptor read/64, error -71
[68940.790592] usb 6-1: not running at top speed; connect to a high speed hub
[68940.809538] usb 6-1: New USB device found, idVendor=0830, idProduct=0061
[68940.809549] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[68940.809555] usb 6-1: Product: palmOne Handheld
[68940.809561] usb 6-1: Manufacturer: palmOne, Inc.
[68940.809565] usb 6-1: SerialNumber: PVG0M5L5V0PM
[68940.809779] usb 6-1: configuration #1 chosen from 1 choice
[68941.176123] usb 6-1: USB disconnect, address 76
[68942.400278] usb 2-1: new high speed USB device using ehci_hcd and address 27
[68942.533876] usb 2-1: New USB device found, idVendor=0830, idProduct=00dd
[68942.533887] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[68942.533893] usb 2-1: Product: palmOne Handheld
[68942.533898] usb 2-1: Manufacturer: palmOne, Inc.
[68942.533903] usb 2-1: SerialNumber: PVG0M5L5V0PM
[68942.534108] usb 2-1: configuration #1 chosen from 1 choice
[68942.535096] scsi13 : SCSI emulation for USB Mass Storage devices
[68942.536812] usb-storage: device found at 27
[68942.536816] usb-storage: waiting for device to settle before scanning
[68947.538150] usb-storage: device scan complete
[68947.539338] scsi 13:0:0:0: Direct-Access palmOne, File storage 1.0 PQ: 0 ANSI: 0
[68947.540327] scsi 13:0:0:1: Direct-Access Sandisk SU256 1.0 PQ: 0 ANSI: 0
[68947.542350] sd 13:0:0:0: Attached scsi generic sg2 type 0
[68947.542604] sd 13:0:0:1: Attached scsi generic sg3 type 0
[68947.542806] sd 13:0:0:0: [sdb] 7818112 512-byte hardware sectors: (4.00 GB/3.72 GiB)
[68947.543574] sd 13:0:0:0: [sdb] Write Protect is off
[68947.543581] sd 13:0:0:0: [sdb] Mode Sense: 0f 00 00 00
[68947.543587] sd 13:0:0:0: [sdb] Assuming drive cache: write through
[68947.547719] sd 13:0:0:1: [sdc] 494080 512-byte hardware sectors: (252 MB/241 MiB)
[68947.557894] sd 13:0:0:0: [sdb] Assuming drive cache: write through
[68947.557906] sdb: sdb1
[68947.561456] sd 13:0:0:0: [sdb] Attached SCSI removable disk
[68947.563587] sd 13:0:0:1: [sdc] Write Protect is on
[68947.563596] sd 13:0:0:1: [sdc] Mode Sense: 0f 00 80 00
[68947.563601] sd 13:0:0:1: [sdc] Assuming drive cache: write through
[68947.580568] sd 13:0:0:1: [sdc] Assuming drive cache: write through
[68947.580581] sdc: sdc1
[68947.601891] sd 13:0:0:1: [sdc] Attached SCSI removable disk
[68948.766318] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[68948.978902] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[68963.419306] usb 2-1: USB disconnect, address 27
[68966.124544] usb 2-1: new high speed USB device using ehci_hcd and address 28
[68966.257401] usb 2-1: New USB device found, idVendor=0830, idProduct=0061
[68966.257412] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[68966.257418] usb 2-1: Product: palmOne Handheld
[68966.257423] usb 2-1: Manufacturer: palmOne, Inc.
[68966.257427] usb 2-1: SerialNumber: PVG0M5L5V0PM
[68966.257633] usb 2-1: configuration #1 chosen from 1 choice
[68967.026856] usb 2-1: USB disconnect, address 28
** Loaded modules:
Module Size Used by
nls_utf8 2000 0
nls_cp437 6928 0
vfat 10512 0
fat 48328 1 vfat
nls_base 8740 4 nls_utf8,nls_cp437,vfat,fat
usb_storage 61488 0
nvidia 10258056 29
ppdev 7784 0
parport_pc 27080 0
lp 10612 0
parport 38224 3 ppdev,parport_pc,lp
bridge 48272 0
stp 2868 1 bridge
bnep 13808 2
sco 10996 2
rfcomm 36032 8
l2cap 21152 16 bnep,rfcomm
acpi_cpufreq 8912 0
cpufreq_userspace 3652 0
cpufreq_powersave 1792 0
cpufreq_conservative 7928 0
cpufreq_stats 4660 0
fuse 54800 3
loop 15980 0
btusb 12756 2
bluetooth 55124 9 bnep,sco,rfcomm,l2cap,btusb
snd_hda_codec_nvhdmi 3536 1
snd_hda_codec_realtek 250260 1
snd_hda_intel 26680 2
snd_hda_codec 75264 3 snd_hda_codec_nvhdmi,snd_hda_codec_realtek,snd_hda_intel
arc4 2048 2
ecb 3072 2
snd_hwdep 8152 1 snd_hda_codec
snd_pcm_oss 37200 0
snd_mixer_oss 15072 1 snd_pcm_oss
joydev 10992 0
snd_pcm 78504 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss
snd_seq_midi 6976 0
uvcvideo 56700 0
snd_rawmidi 23008 1 snd_seq_midi
iwlagn 83508 0
snd_seq_midi_event 7712 1 snd_seq_midi
snd_seq 51376 2 snd_seq_midi,snd_seq_midi_event
snd_timer 21824 2 snd_pcm,snd_seq
iwlcore 106848 1 iwlagn
snd_seq_device 7476 3 snd_seq_midi,snd_rawmidi,snd_seq
i2c_i801 10464 0
videodev 36784 1 uvcvideo
acer_wmi 17240 0
v4l1_compat 12932 2 uvcvideo,videodev
snd 63912 15 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
rfkill 12116 5 iwlcore,acer_wmi
serio_raw 5844 0
v4l2_compat_ioctl32 9312 1 videodev
led_class 5048 2 iwlcore,acer_wmi
pcspkr 2800 0
soundcore 7984 1 snd
mac80211 161424 2 iwlagn,iwlcore
i2c_core 25456 2 nvidia,i2c_i801
wmi 7488 1 acer_wmi
psmouse 42172 0
evdev 10448 14
ac 3872 0
battery 7840 0
button 6512 0
processor 40176 3 acpi_cpufreq
cfg80211 65480 3 iwlagn,iwlcore,mac80211
snd_page_alloc 10000 2 snd_hda_intel,snd_pcm
xfs 457696 5
exportfs 4672 1 xfs
sg 24024 0
sr_mod 15908 0
cdrom 34344 1 sr_mod
sd_mod 33736 6
crc_t10dif 2096 1 sd_mod
usbhid 37344 0
hid 41376 1 usbhid
ahci 36480 5
libata 175532 1 ahci
uhci_hcd 22208 0
scsi_mod 158800 5 usb_storage,sg,sr_mod,sd_mod,libata
sky2 46644 0
ehci_hcd 33852 0
intel_agp 28752 0
video 21900 0
output 3472 1 video
thermal 15936 0
fan 5240 0
thermal_sys 16448 4 processor,video,thermal,fan
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub [8086:2a40] (rev 07)
Subsystem: Acer Incorporated [ALI] Device [1025:013f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:01.0 PCI bridge [0604]: Intel Corporation Mobile 4 Series Chipset PCI Express Graphics Port [8086:2a41] (rev 07) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: cc000000-ceffffff
Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1a.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 [8086:2937] (rev 03) (prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI] Device [1025:013f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 1800 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 [8086:2938] (rev 03) (prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI] Device [1025:013f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 20
Region 4: I/O ports at 1820 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.2 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 [8086:2939] (rev 03) (prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI] Device [1025:013f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 20
Region 4: I/O ports at 1840 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 [8086:293c] (rev 03) (prog-if 20 [EHCI])
Subsystem: Acer Incorporated [ALI] Device [1025:013f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 20
Region 0: Memory at f6504800 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1b.0 Audio device [0403]: Intel Corporation 82801I (ICH9 Family) HD Audio Controller [8086:293e] (rev 03)
Subsystem: Acer Incorporated [ALI] Device [1025:013f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at f6500000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
00:1c.0 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 [8086:2940] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: f6100000-f61fffff
Prefetchable memory behind bridge: 00000000c0000000-00000000c00fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1c.1 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 [8086:2942] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Memory behind bridge: f6200000-f62fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1c.2 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 3 [8086:2944] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1c.3 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 [8086:2946] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=07, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: f4000000-f60fffff
Prefetchable memory behind bridge: 00000000f0000000-00000000f1ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1c.4 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 [8086:2948] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=08, subordinate=0a, sec-latency=0
I/O behind bridge: 00005000-00005fff
Memory behind bridge: f8000000-f9ffffff
Prefetchable memory behind bridge: 00000000f2000000-00000000f3ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1d.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 [8086:2934] (rev 03) (prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI] Device [1025:013f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at 1860 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 [8086:2935] (rev 03) (prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI] Device [1025:013f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at 1880 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 [8086:2936] (rev 03) (prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI] Device [1025:013f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 18a0 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 [8086:293a] (rev 03) (prog-if 20 [EHCI])
Subsystem: Acer Incorporated [ALI] Device [1025:013f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f6504c00 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev 93) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=0d, subordinate=0d, sec-latency=0
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation ICH9M LPC Interface Controller [8086:2919] (rev 03)
Subsystem: Acer Incorporated [ALI] Device [1025:013f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.2 SATA controller [0106]: Intel Corporation ICH9M/M-E SATA AHCI Controller [8086:2929] (rev 03) (prog-if 01 [AHCI 1.0])
Subsystem: Acer Incorporated [ALI] Device [1025:013f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 31
Region 0: I/O ports at 18f0 [size=8]
Region 1: I/O ports at 18e4 [size=4]
Region 2: I/O ports at 18e8 [size=8]
Region 3: I/O ports at 18e0 [size=4]
Region 4: I/O ports at 18c0 [size=32]
Region 5: Memory at f6504000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 82801I (ICH9 Family) SMBus Controller [8086:2930] (rev 03)
Subsystem: Acer Incorporated [ALI] Device [1025:013f]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 19
Region 0: Memory at c0100000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 1c00 [size=32]
Kernel driver in use: i801_smbus
01:00.0 VGA compatible controller [0300]: nVidia Corporation G96 [GeForce 9600M GT] [10de:0649] (rev a1) (prog-if 00 [VGA controller])
Subsystem: Acer Incorporated [ALI] Device [1025:013f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at ce000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at cc000000 (64-bit, non-prefetchable) [size=32M]
Region 5: I/O ports at 2000 [size=128]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: nvidia
02:00.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8071 PCI-E Gigabit Ethernet Controller [11ab:436b] (rev 16)
Subsystem: Acer Incorporated [ALI] Device [1025:013f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 30
Region 0: Memory at f6100000 (64-bit, non-prefetchable) [size=16K]
Region 2: I/O ports at 3000 [size=256]
[virtual] Expansion ROM at c0000000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: sky2
03:00.0 Network controller [0280]: Intel Corporation Wireless WiFi Link 5100 [8086:4232]
Subsystem: Intel Corporation PRO/Wireless 5100ABG Network Connection [8086:1206]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 32
Region 0: Memory at f6200000 (64-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: iwlagn
-- System Information:
Debian Release: squeeze/sid
APT prefers testing
APT policy: (990, 'testing'), (500, 'unstable'), (1, 'experimental')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.30-1-amd64 (SMP w/2 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.30-1-amd64 depends on:
ii debconf [debconf-2.0] 1.5.27 Debian configuration management sy
ii initramfs-tools [linux-initra 0.93.4 tools for generating an initramfs
ii module-init-tools 3.9-2 tools for managing Linux kernel mo
linux-image-2.6.30-1-amd64 recommends no packages.
Versions of packages linux-image-2.6.30-1-amd64 suggests:
ii grub 0.97-55 GRand Unified Bootloader (dummy pa
ii grub-legacy [grub] 0.97-55 GRand Unified Bootloader (Legacy v
pn linux-doc-2.6.30 <none> (no description available)
-- debconf information:
linux-image-2.6.30-1-amd64/preinst/initrd-2.6.30-1-amd64:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.30-1-amd64/postinst/create-kimage-link-2.6.30-1-amd64: true
linux-image-2.6.30-1-amd64/preinst/abort-overwrite-2.6.30-1-amd64:
linux-image-2.6.30-1-amd64/postinst/bootloader-error-2.6.30-1-amd64:
linux-image-2.6.30-1-amd64/preinst/lilo-has-ramdisk:
linux-image-2.6.30-1-amd64/postinst/old-dir-initrd-link-2.6.30-1-amd64: true
linux-image-2.6.30-1-amd64/postinst/old-initrd-link-2.6.30-1-amd64: true
linux-image-2.6.30-1-amd64/postinst/kimage-is-a-directory:
linux-image-2.6.30-1-amd64/preinst/lilo-initrd-2.6.30-1-amd64: true
linux-image-2.6.30-1-amd64/prerm/removing-running-kernel-2.6.30-1-amd64: true
linux-image-2.6.30-1-amd64/prerm/would-invalidate-boot-loader-2.6.30-1-amd64: true
linux-image-2.6.30-1-amd64/preinst/elilo-initrd-2.6.30-1-amd64: true
linux-image-2.6.30-1-amd64/preinst/bootloader-initrd-2.6.30-1-amd64: true
linux-image-2.6.30-1-amd64/preinst/overwriting-modules-2.6.30-1-amd64: true
linux-image-2.6.30-1-amd64/postinst/depmod-error-2.6.30-1-amd64: false
linux-image-2.6.30-1-amd64/preinst/failed-to-move-modules-2.6.30-1-amd64:
linux-image-2.6.30-1-amd64/postinst/depmod-error-initrd-2.6.30-1-amd64: false
linux-image-2.6.30-1-amd64/preinst/abort-install-2.6.30-1-amd64:
linux-image-2.6.30-1-amd64/postinst/bootloader-test-error-2.6.30-1-amd64:
linux-image-2.6.30-1-amd64/postinst/old-system-map-link-2.6.30-1-amd64: true
--- End Message ---