[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Bug#508235: marked as done (linux-image-2.6.26-1-686: SATA hard drives recognized in 2.6.25-2 but not in 2.6.26-1)



Your message dated Wed, 17 Mar 2010 23:24:58 +0100
with message-id <20100317222458.GA5697@galadriel.inutil.org>
and subject line Re: linux-image-2.6.26-1-686: SATA hard drives recognized in 2.6.25-2 but not in 2.6.26-1
has caused the Debian Bug report #508235,
regarding linux-image-2.6.26-1-686: SATA hard drives recognized in 2.6.25-2 but not in 2.6.26-1
to be marked as done.

This means that you claim that the problem has been dealt with.
If this is not the case it is now your responsibility to reopen the
Bug report if necessary, and/or fix the problem forthwith.

(NB: If you are a system administrator and have no idea what this
message is talking about, this may indicate a serious mail system
misconfiguration somewhere. Please contact owner@bugs.debian.org
immediately.)


-- 
508235: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=508235
Debian Bug Tracking System
Contact owner@bugs.debian.org with problems
--- Begin Message ---
Package: linux-image-2.6.26-1-686
Version: 2.6.26-11
Severity: important


My two SAMSUNG HA250JC hard drives were working fine until apt-get upgraded
the kernel from 2.6.25-2 to 2.6.26-1 (Debian testing).

Both hard drives are plugged externally to my laptop through a PCMCIA card with 2 eSATA ports.

The following excerpt from /var/log/dmesg might be be relevant when I boot with 2.6.26-1:

[   15.896167] ata3: link is slow to respond, please be patient (ready=-19)
[   20.544166] ata3: COMRESET failed (errno=-16)
[   25.904165] ata3: link is slow to respond, please be patient (ready=-19)
[   30.552167] ata3: COMRESET failed (errno=-16)
[   35.912165] ata3: link is slow to respond, please be patient (ready=-19)
[   65.596166] ata3: COMRESET failed (errno=-16)
[   70.620178] ata3: COMRESET failed (errno=-16)
[   70.620238] ata3: reset failed, giving up

With 2.6.25-2, I am getting the following result:

[   92.236169] ata3: hard resetting link
[   97.837264] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[   97.845734] ata3.00: ATA-7: SAMSUNG HA250JC, WE100-33, max UDMA/133
[   97.845740] ata3.00: 488397168 sectors, multi 0: LBA48 
[   97.845743] ata3.00: applying bridge limits
[   97.861619] ata3.00: configured for UDMA/100
[   97.861633] ata3: EH complete
[   97.861747] scsi 2:0:0:0: Direct-Access     ATA      SAMSUNG HA250JC  WE10 PQ: 0 ANSI: 5
[   97.865796] sd 2:0:0:0: [sdb] 488397168 512-byte hardware sectors (250059 MB)
[   97.868908] sd 2:0:0:0: [sdb] Write Protect is off
[   97.872926] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   97.873268] sd 2:0:0:0: [sdb] 488397168 512-byte hardware sectors (250059 MB)
[   97.876079] sd 2:0:0:0: [sdb] Write Protect is off
[   97.879716] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   97.890512] sd 2:0:0:0: [sdb] Attached SCSI disk
[   97.890553] sd 2:0:0:0: Attached scsi generic sg2 type 0


I found a few similar reports; maybe there are related:
http://bugs.archlinux.org/task/11388
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=501023

which pointed me to an on-going patch, maybe related too: 
http://article.gmane.org/gmane.linux.ide/34077/raw


If you want further information, do not hesitate to ask, I can reproduce the problem.
This bug prevents me from upgrading to 2.6.26.

Here is the full dmesg log of the boot process with 2.6.26-1:

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.26-1-686 (Debian 2.6.26-11) (waldi@debian.org) (gcc version 4.1.3 20080623 (prerelease) (Debian 4.1.2-23)) #1 SMP Wed Nov 26 19:14:11 UTC 2008
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
[    0.000000]  BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000001f7d1800 (usable)
[    0.000000]  BIOS-e820: 000000001f7d1800 - 0000000020000000 (reserved)
[    0.000000]  BIOS-e820: 00000000e0000000 - 00000000f0007000 (reserved)
[    0.000000]  BIOS-e820: 00000000f0008000 - 00000000f000c000 (reserved)
[    0.000000]  BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[    0.000000]  BIOS-e820: 00000000fed20000 - 00000000fee10000 (reserved)
[    0.000000]  BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
[    0.000000] 0MB HIGHMEM available.
[    0.000000] 503MB LOWMEM available.
[    0.000000] Entering add_active_range(0, 0, 128977) 0 entries of 256 used
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA             0 ->     4096
[    0.000000]   Normal       4096 ->   128977
[    0.000000]   HighMem    128977 ->   128977
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0:        0 ->   128977
[    0.000000] On node 0 totalpages: 128977
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 4064 pages, LIFO batch:0
[    0.000000]   Normal zone: 976 pages used for memmap
[    0.000000]   Normal zone: 123905 pages, LIFO batch:31
[    0.000000]   HighMem zone: 0 pages used for memmap
[    0.000000]   Movable zone: 0 pages used for memmap
[    0.000000] DMI 2.3 present.
[    0.000000] ACPI: RSDP 000FC9B0, 0014 (r0 DELL  )
[    0.000000] ACPI: RSDT 1F7D1F90, 0040 (r1 DELL    CPi R   27D50A02 ASL        61)
[    0.000000] ACPI: FACP 1F7D2C00, 0074 (r1 DELL    CPi R   27D50A02 ASL        61)
[    0.000000] ACPI: DSDT 1F7D3800, 3C51 (r1 INT430 SYSFexxx     1001 MSFT  100000E)
[    0.000000] ACPI: FACS 1F7E2000, 0040
[    0.000000] ACPI: APIC 1F7D3400, 0068 (r1 DELL    CPi R   27D50A02 ASL        47)
[    0.000000] ACPI: ASF! 1F7D3000, 005B (r16 DELL    CPi R   27D50A02 ASL        61)
[    0.000000] ACPI: MCFG 1F7D33C0, 003E (r16 DELL    CPi R   27D50A02 ASL        61)
[    0.000000] ACPI: SSDT 1F7D23E6, 023E (r1  PmRef  Cpu0Ist     3000 INTL 20030522)
[    0.000000] ACPI: SSDT 1F7D220E, 01D8 (r1  PmRef  Cpu0Cst     3001 INTL 20030522)
[    0.000000] ACPI: SSDT 1F7D2013, 01FB (r1  PmRef    CpuPm     3000 INTL 20030522)
[    0.000000] ACPI: PM-Timer IO Port: 0x1008
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] Allocating PCI resources starting at 30000000 (gap: 20000000:c0000000)
[    0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 0000000000100000
[    0.000000] SMP: Allowing 2 CPUs, 1 hotplug CPUs
[    0.000000] PERCPU: Allocating 37960 bytes of per cpu data
[    0.000000] NR_CPUS: 8, nr_cpu_ids: 2
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 127969
[    0.000000] Kernel command line: root=/dev/sda3 ro 
[    0.000000] mapped APIC to ffffb000 (fee00000)
[    0.000000] mapped IOAPIC to ffffa000 (fec00000)
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[    0.000000] Detected 1729.055 MHz processor.
[    0.004000] Console: colour VGA+ 80x25
[    0.004000] console [tty0] enabled
[    0.004000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.004000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.004000] Memory: 500932k/515908k available (1768k kernel code, 14368k reserved, 752k data, 244k init, 0k highmem)
[    0.004000] virtual kernel memory layout:
[    0.004000]     fixmap  : 0xfff4c000 - 0xfffff000   ( 716 kB)
[    0.004000]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[    0.004000]     vmalloc : 0xe0000000 - 0xff7fe000   ( 503 MB)
[    0.004000]     lowmem  : 0xc0000000 - 0xdf7d1000   ( 503 MB)
[    0.004000]       .init : 0xc037f000 - 0xc03bc000   ( 244 kB)
[    0.004000]       .data : 0xc02ba293 - 0xc0376620   ( 752 kB)
[    0.004000]       .text : 0xc0100000 - 0xc02ba293   (1768 kB)
[    0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[    0.084124] Calibrating delay using timer specific routine.. 3462.25 BogoMIPS (lpj=6924519)
[    0.084272] Security Framework initialized
[    0.084332] SELinux:  Disabled at boot.
[    0.084388] Capability LSM initialized
[    0.084457] Mount-cache hash table entries: 512
[    0.084663] Initializing cgroup subsys ns
[    0.084723] Initializing cgroup subsys cpuacct
[    0.084780] Initializing cgroup subsys devices
[    0.084857] CPU: L1 I cache: 32K, L1 D cache: 32K
[    0.084945] CPU: L2 cache: 2048K
[    0.085001] Intel machine check architecture supported.
[    0.085061] Intel machine check reporting enabled on CPU#0.
[    0.085127] Checking 'hlt' instruction... OK.
[    0.100474] SMP alternatives: switching to UP code
[    0.105692] ACPI: Core revision 20080321
[    0.115642] ENABLING IO-APIC IRQs
[    0.115893] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.155668] CPU0: Intel(R) Pentium(R) M processor 1.73GHz stepping 08
[    0.156009] Brought up 1 CPUs
[    0.156009] Total of 1 processors activated (3462.25 BogoMIPS).
[    0.156009] CPU0 attaching sched-domain:
[    0.156009]  domain 0: span 0
[    0.156009]   groups: 0
[    0.156009] net_namespace: 660 bytes
[    0.156009] Booting paravirtualized kernel on bare hardware
[    0.156009] NET: Registered protocol family 16
[    0.156009] ACPI: bus type pci registered
[    0.156009] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[    0.156009] PCI: MCFG area at e0000000 reserved in E820
[    0.156009] PCI: Using MMCONFIG for extended config space
[    0.156009] PCI: Using configuration type 1 for base access
[    0.156009] Setting up standard PCI resources
[    0.156010] ACPI: EC: Look up EC in DSDT
[    0.186226] ACPI: SSDT 1F7D1FD0, 0043 (r1  LMPWR  DELLLOM     1001 INTL 20030522)
[    0.186953] ACPI: Interpreter enabled
[    0.187010] ACPI: (supports S0 S3 S4 S5)
[    0.187196] ACPI: Using IOAPIC for interrupt routing
[    0.232014] ACPI: PCI Root Bridge [PCI0] (0000:00)
[    0.232014] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
[    0.232014] pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
[    0.232014] pci 0000:00:1f.0: quirk: region 1080-10bf claimed by ICH6 GPIO
[    0.232014] PCI: Transparent bridge - 0000:00:1e.0
[    0.232014] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.232485] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT]
[    0.276017] ACPI: PCI Interrupt Link [LNKA] (IRQs 9 10 *11)
[    0.276017] ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7) *10
[    0.276017] ACPI: PCI Interrupt Link [LNKC] (IRQs *9 10 11)
[    0.276017] ACPI: PCI Interrupt Link [LNKD] (IRQs *5 7 9 10 11)
[    0.276017] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[    0.276017] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[    0.276662] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[    0.277400] Linux Plug and Play Support v0.97 (c) Adam Belay
[    0.277486] pnp: PnP ACPI init
[    0.277545] ACPI: bus type pnp registered
[    0.337665] pnp 00:0e: can't add resource for IO 0x57b0-0x57bb
[    0.344111] pnp: PnP ACPI: found 15 devices
[    0.344168] ACPI: ACPI bus type pnp unregistered
[    0.344226] PnPBIOS: Disabled by ACPI PNP
[    0.344512] PCI: Using ACPI for IRQ routing
[    0.344822] hpet clockevent registered
[    0.344829] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.345009] hpet0: 3 64-bit timers, 14318180 Hz
[    0.346131] system 00:00: iomem range 0x0-0x9fbff could not be reserved
[    0.346194] system 00:00: iomem range 0x9fc00-0x9ffff could not be reserved
[    0.346256] system 00:00: iomem range 0xc0000-0xcffff could not be reserved
[    0.346319] system 00:00: iomem range 0xe0000-0xfffff could not be reserved
[    0.346381] system 00:00: iomem range 0x100000-0x1f7d17ff could not be reserved
[    0.346460] system 00:00: iomem range 0x1f7d1800-0x1f7fffff could not be reserved
[    0.346540] system 00:00: iomem range 0x1f800000-0x1fffffff could not be reserved
[    0.346619] system 00:00: iomem range 0xfeda0000-0xfedfffff could not be reserved
[    0.346698] system 00:00: iomem range 0xffb00000-0xffffffff could not be reserved
[    0.346777] system 00:00: iomem range 0xfec00000-0xfec0ffff could not be reserved
[    0.346856] system 00:00: iomem range 0xfee00000-0xfee0ffff could not be reserved
[    0.346935] system 00:00: iomem range 0xfed20000-0xfed9ffff could not be reserved
[    0.347014] system 00:00: iomem range 0xf0000000-0xf0003fff could not be reserved
[    0.347093] system 00:00: iomem range 0xf0004000-0xf0004fff could not be reserved
[    0.347172] system 00:00: iomem range 0xf0005000-0xf0005fff could not be reserved
[    0.347251] system 00:00: iomem range 0xf0006000-0xf0006fff could not be reserved
[    0.347330] system 00:00: iomem range 0xf0008000-0xf000bfff could not be reserved
[    0.347409] system 00:00: iomem range 0xe0000000-0xefffffff could not be reserved
[    0.347491] system 00:02: ioport range 0x4d0-0x4d1 has been reserved
[    0.347553] system 00:02: ioport range 0x1000-0x1005 has been reserved
[    0.347615] system 00:02: ioport range 0x1008-0x100f has been reserved
[    0.347679] system 00:03: ioport range 0xf400-0xf4fe has been reserved
[    0.347741] system 00:03: ioport range 0x1006-0x1007 has been reserved
[    0.347803] system 00:03: ioport range 0x100a-0x1059 could not be reserved
[    0.347865] system 00:03: ioport range 0x1060-0x107f has been reserved
[    0.347927] system 00:03: ioport range 0x1080-0x10bf has been reserved
[    0.347989] system 00:03: ioport range 0x10c0-0x10df has been reserved
[    0.348021] system 00:03: ioport range 0x10e0-0x10ff has been reserved
[    0.348091] system 00:08: ioport range 0x900-0x90f has been reserved
[    0.348152] system 00:08: ioport range 0x910-0x91f has been reserved
[    0.348213] system 00:08: ioport range 0x920-0x92f has been reserved
[    0.349265] system 00:08: ioport range 0x93c-0x93f has been reserved
[    0.349326] system 00:08: ioport range 0x940-0x97f has been reserved
[    0.349392] system 00:0d: ioport range 0x930-0x93b has been reserved
[    0.349456] system 00:0e: ioport range 0x7b0-0x7bb has been reserved
[    0.349517] system 00:0e: ioport range 0x7c0-0x7df has been reserved
[    0.349579] system 00:0e: ioport range 0xbb0-0xbbb has been reserved
[    0.349640] system 00:0e: ioport range 0xbc0-0xbdf has been reserved
[    0.349703] system 00:0e: ioport range 0xfb0-0xfbb has been reserved
[    0.349764] system 00:0e: ioport range 0xfc0-0xfdf has been reserved
[    0.349825] system 00:0e: ioport range 0x13b0-0x13bb has been reserved
[    0.349887] system 00:0e: ioport range 0x13c0-0x13df has been reserved
[    0.349948] system 00:0e: ioport range 0x17b0-0x17bb has been reserved
[    0.350010] system 00:0e: ioport range 0x17c0-0x17df has been reserved
[    0.350072] system 00:0e: ioport range 0x1bb0-0x1bbb has been reserved
[    0.350134] system 00:0e: ioport range 0x1bc0-0x1bdf has been reserved
[    0.350196] system 00:0e: ioport range 0x1fb0-0x1fbb has been reserved
[    0.350257] system 00:0e: ioport range 0x1fc0-0x1fdf has been reserved
[    0.350319] system 00:0e: ioport range 0x23b0-0x23bb has been reserved
[    0.350381] system 00:0e: ioport range 0x23c0-0x23df has been reserved
[    0.350442] system 00:0e: ioport range 0x27b0-0x27bb has been reserved
[    0.350504] system 00:0e: ioport range 0x27c0-0x27df has been reserved
[    0.350565] system 00:0e: ioport range 0x2bb0-0x2bbb has been reserved
[    0.350627] system 00:0e: ioport range 0x2bc0-0x2bdf has been reserved
[    0.350688] system 00:0e: ioport range 0x2fb0-0x2fbb has been reserved
[    0.350750] system 00:0e: ioport range 0x2fc0-0x2fdf has been reserved
[    0.350811] system 00:0e: ioport range 0x33b0-0x33bb has been reserved
[    0.350872] system 00:0e: ioport range 0x33c0-0x33df has been reserved
[    0.350934] system 00:0e: ioport range 0x37b0-0x37bb has been reserved
[    0.350995] system 00:0e: ioport range 0x37c0-0x37df has been reserved
[    0.351057] system 00:0e: ioport range 0x3bb0-0x3bbb has been reserved
[    0.351118] system 00:0e: ioport range 0x3bc0-0x3bdf has been reserved
[    0.351180] system 00:0e: ioport range 0x3fb0-0x3fbb has been reserved
[    0.351241] system 00:0e: ioport range 0x3fc0-0x3fdf has been reserved
[    0.351302] system 00:0e: ioport range 0x43b0-0x43bb has been reserved
[    0.351364] system 00:0e: ioport range 0x43c0-0x43df has been reserved
[    0.351426] system 00:0e: ioport range 0x47b0-0x47bb has been reserved
[    0.351488] system 00:0e: ioport range 0x47c0-0x47df has been reserved
[    0.351550] system 00:0e: ioport range 0x4bb0-0x4bbb has been reserved
[    0.351611] system 00:0e: ioport range 0x4bc0-0x4bdf has been reserved
[    0.351673] system 00:0e: ioport range 0x4fb0-0x4fbb has been reserved
[    0.351735] system 00:0e: ioport range 0x4fc0-0x4fdf has been reserved
[    0.351796] system 00:0e: ioport range 0x53b0-0x53bb has been reserved
[    0.351858] system 00:0e: ioport range 0x53c0-0x53df has been reserved
[    0.382265] PCI: region 0000:03:01.0/9 too large: 0x0000000000000000-0x0000000003ffffff
[    0.382350] PCI: Bridge: 0000:00:1c.0
[    0.382404]   IO window: disabled.
[    0.382461]   MEM window: 0xdfd00000-0xdfdfffff
[    0.382520]   PREFETCH window: disabled.
[    0.382586] PCI: Bus 4, cardbus bridge: 0000:03:01.0
[    0.382643]   IO window: 0x00006000-0x000060ff
[    0.382702]   IO window: 0x00006400-0x000064ff
[    0.382761]   MEM window: 0x30000000-0x33ffffff
[    0.382821] PCI: Bridge: 0000:00:1e.0
[    0.382876]   IO window: 6000-6fff
[    0.382934]   MEM window: 0xdfc00000-0xdfcfffff
[    0.382992]   PREFETCH window: disabled.
[    0.383074] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
[    0.383185] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[    0.383199] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[    0.383216] pci 0000:03:01.0: enabling device (0000 -> 0003)
[    0.383277] ACPI: PCI Interrupt 0000:03:01.0[A] -> GSI 19 (level, low) -> IRQ 19
[    0.383409] NET: Registered protocol family 2
[    0.383547] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.383792] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    0.383970] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[    0.384133] TCP: Hash tables configured (established 16384 bind 16384)
[    0.384194] TCP reno registered
[    0.384313] NET: Registered protocol family 1
[    0.384472] checking if image is initramfs... it is
[    0.848009] Switched to high resolution mode on CPU 0
[    0.983324] Freeing initrd memory: 6592k freed
[    0.984108] audit: initializing netlink socket (disabled)
[    0.984184] type=2000 audit(1228765642.984:1): initialized
[    0.984367] Total HugeTLB memory allocated, 0
[    0.984522] VFS: Disk quotas dquot_6.5.1
[    0.984608] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.984712] msgmni has been set to 991
[    0.984892] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    0.984972] io scheduler noop registered
[    0.985027] io scheduler anticipatory registered
[    0.985084] io scheduler deadline registered
[    0.985155] io scheduler cfq registered (default)
[    0.985226] pci 0000:00:02.0: Boot video device
[    0.985428] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[    0.985472] assign_interrupt_mode Found MSI capability
[    0.985575] Allocate Port Service[0000:00:1c.0:pcie00]
[    0.985617] Allocate Port Service[0000:00:1c.0:pcie02]
[    0.985654] Allocate Port Service[0000:00:1c.0:pcie03]
[    0.985985] isapnp: Scanning for PnP cards...
[    1.340254] isapnp: No Plug & Play device found
[    1.342767] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[    1.342985] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.343498] 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.343685] ACPI: PCI Interrupt 0000:00:1e.3[B] -> GSI 17 (level, low) -> IRQ 17
[    1.343799] ACPI: PCI interrupt for device 0000:00:1e.3 disabled
[    1.345178] brd: module loaded
[    1.345326] PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    1.350495] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.350557] serio: i8042 AUX port at 0x60,0x64 irq 12
[    1.350747] mice: PS/2 mouse device common for all mice
[    1.350925] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[    1.351003] rtc0: alarms up to one month, y3k
[    1.351090] cpuidle: using governor ladder
[    1.351146] cpuidle: using governor menu
[    1.351204] No iBFT detected.
[    1.351689] TCP cubic registered
[    1.351744] NET: Registered protocol family 17
[    1.351804] Using IPI No-Shortcut mode
[    1.351971] registered taskstats version 1
[    1.352188] rtc_cmos 00:06: setting system clock to 2008-12-08 19:47:24 UTC (1228765644)
[    1.352405] Freeing unused kernel memory: 244k freed
[    1.355577] input: AT Translated Set 2 keyboard as /class/input/input0
[    1.438167] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3])
[    1.438437] ACPI: ACPI0007:00 is registered as cooling_device0
[    1.438498] ACPI: Processor [CPU0] (supports 8 throttling states)
[    1.441720] ACPI: LNXTHERM:01 is registered as thermal_zone0
[    1.443341] ACPI: Thermal Zone [THM] (61 C)
[    1.937510] ACPI: ACPI Dock Station Driver
[    1.967704] tg3.c:v3.92.1 (June 9, 2008)
[    1.967796] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[    1.967914] PCI: Setting latency timer of device 0000:02:00.0 to 64
[    1.989132] eth0: Tigon3 [partno(BCM95751) rev 4001 PHY(5750)] (PCI Express) 10/100/1000Base-T Ethernet 00:15:c5:21:30:61
[    1.989223] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
[    1.989302] eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[    2.015828] usbcore: registered new interface driver usbfs
[    2.015917] usbcore: registered new interface driver hub
[    2.016014] usbcore: registered new device driver usb
[    2.020832] USB Universal Host Controller Interface driver v3.0
[    2.020933] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16
[    2.021053] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[    2.021058] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    2.021255] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[    2.021369] uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000bf80
[    2.021505] usb usb1: configuration #1 chosen from 1 choice
[    2.021589] hub 1-0:1.0: USB hub found
[    2.021648] hub 1-0:1.0: 2 ports detected
[    2.124128] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[    2.124196] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.124274] usb usb1: Product: UHCI Host Controller
[    2.124331] usb usb1: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[    2.124391] usb usb1: SerialNumber: 0000:00:1d.0
[    2.124488] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 17
[    2.124609] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[    2.124614] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    2.124692] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[    2.124803] uhci_hcd 0000:00:1d.1: irq 17, io base 0x0000bf60
[    2.124940] usb usb2: configuration #1 chosen from 1 choice
[    2.125027] hub 2-0:1.0: USB hub found
[    2.125087] hub 2-0:1.0: 2 ports detected
[    2.144253] SCSI subsystem initialized
[    2.164129] libata version 3.00 loaded.
[    2.228129] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    2.228197] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.228276] usb usb2: Product: UHCI Host Controller
[    2.228333] usb usb2: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[    2.228392] usb usb2: SerialNumber: 0000:00:1d.1
[    2.228497] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[    2.228617] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[    2.228622] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    2.228706] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[    2.228816] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000bf40
[    2.228953] usb usb3: configuration #1 chosen from 1 choice
[    2.229037] hub 3-0:1.0: USB hub found
[    2.229097] hub 3-0:1.0: 2 ports detected
[    2.271772] Marking TSC unstable due to: TSC halts in idle.
[    2.367127] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    2.367127] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.367127] usb usb3: Product: UHCI Host Controller
[    2.367127] usb usb3: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[    2.367127] usb usb3: SerialNumber: 0000:00:1d.2
[    2.367127] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 19
[    2.367127] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[    2.367127] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    2.367127] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[    2.367127] uhci_hcd 0000:00:1d.3: irq 19, io base 0x0000bf20
[    2.367127] usb usb4: configuration #1 chosen from 1 choice
[    2.367127] hub 4-0:1.0: USB hub found
[    2.367127] hub 4-0:1.0: 2 ports detected
[    2.376436] Clocksource tsc unstable (delta = -101834951 ns)
[    2.396313] usb 1-2: new full speed USB device using uhci_hcd and address 2
[    2.467849] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    2.467849] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.467849] usb usb4: Product: UHCI Host Controller
[    2.467849] usb usb4: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[    2.467849] usb usb4: SerialNumber: 0000:00:1d.3
[    2.467849] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 16 (level, low) -> IRQ 16
[    2.467849] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[    2.467849] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    2.467849] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
[    2.467849] ehci_hcd 0000:00:1d.7: debug port 1
[    2.467849] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[    2.467849] ehci_hcd 0000:00:1d.7: irq 16, io mem 0xffa80800
[    2.514356] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[    2.514356] usb usb5: configuration #1 chosen from 1 choice
[    2.514356] hub 5-0:1.0: USB hub found
[    2.514356] hub 5-0:1.0: 8 ports detected
[    2.617458] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[    2.617458] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.617458] usb usb5: Product: EHCI Host Controller
[    2.617458] usb usb5: Manufacturer: Linux 2.6.26-1-686 ehci_hcd
[    2.617458] usb usb5: SerialNumber: 0000:00:1d.7
[    2.617458] ahci 0000:00:1f.2: version 3.0
[    2.617458] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level, low) -> IRQ 17
[    2.617458] ACPI: PCI interrupt for device 0000:00:1f.2 disabled
[    2.617458] ahci: probe of 0000:00:1f.2 failed with error -22
[    2.617458] ata_piix 0000:00:1f.2: version 2.12
[    2.617458] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level, low) -> IRQ 17
[    2.617458] ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
[    2.756069] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[    2.756227] scsi0 : ata_piix
[    2.756390] scsi1 : ata_piix
[    2.758473] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xbfa0 irq 14
[    2.758537] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xbfa8 irq 15
[    2.896166] usb 1-2: device not accepting address 2, error -71
[    2.920926] ata1.00: ATA-6: TOSHIBA MK4032GAX, AD102D, max UDMA/100
[    2.920988] ata1.00: 78140160 sectors, multi 8: LBA48 
[    2.921046] ata1.00: applying bridge limits
[    2.928931] ata1.00: configured for UDMA/100
[    2.952195] hub 1-0:1.0: unable to enumerate USB device on port 2
[    3.092597] ata2.00: ATAPI: HL-DT-ST DVD-ROM GDR-8084N, 1.01, max UDMA/33
[    3.108536] ata2.00: configured for UDMA/33
[    3.108702] scsi 0:0:0:0: Direct-Access     ATA      TOSHIBA MK4032GA AD10 PQ: 0 ANSI: 5
[    3.112961] scsi 1:0:0:0: CD-ROM            HL-DT-ST DVD-ROM GDR8084N 1.01 PQ: 0 ANSI: 5
[    3.119276] Uniform Multi-Platform E-IDE driver
[    3.119337] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[    3.149649] Driver 'sd' needs updating - please use bus_type methods
[    3.149816] sd 0:0:0:0: [sda] 78140160 512-byte hardware sectors (40008 MB)
[    3.149898] sd 0:0:0:0: [sda] Write Protect is off
[    3.149956] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    3.149992] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.150139] sd 0:0:0:0: [sda] 78140160 512-byte hardware sectors (40008 MB)
[    3.150219] sd 0:0:0:0: [sda] Write Protect is off
[    3.150277] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    3.150313] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.150396]  sda:<4>Driver 'sr' needs updating - please use bus_type methods
[    3.178181]  sda1 sda2 sda3 sda4 < sda5 >
[    3.204848] sd 0:0:0:0: [sda] Attached SCSI disk
[    3.216524] sr0: scsi3-mmc drive: 24x/24x cd/rw xa/form2 cdda tray
[    3.216592] Uniform CD-ROM driver Revision: 3.20
[    3.216732] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    3.227644] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    3.227726] sr 1:0:0:0: Attached scsi generic sg1 type 5
[    3.320044] usb 5-2: new high speed USB device using ehci_hcd and address 2
[    3.452447] usb 5-2: configuration #1 chosen from 1 choice
[    3.452656] hub 5-2:1.0: USB hub found
[    3.452765] hub 5-2:1.0: 4 ports detected
[    3.548775] device-mapper: uevent: version 1.0.3
[    3.549900] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
[    3.556114] usb 5-2: New USB device found, idVendor=413c, idProduct=0058
[    3.556183] usb 5-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    3.579459] PM: Starting manual resume from disk
[    3.615577] kjournald starting.  Commit interval 5 seconds
[    3.615577] EXT3-fs: mounted filesystem with ordered data mode.
[    3.996163] usb 5-2.1: new high speed USB device using ehci_hcd and address 4
[    4.088449] usb 5-2.1: configuration #1 chosen from 1 choice
[    4.088651] hub 5-2.1:1.0: USB hub found
[    4.088739] hub 5-2.1:1.0: 4 ports detected
[    4.192089] usb 5-2.1: New USB device found, idVendor=0424, idProduct=2504
[    4.192153] usb 5-2.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    4.432029] usb 2-1: new full speed USB device using uhci_hcd and address 2
[    4.629314] usb 2-1: configuration #1 chosen from 1 choice
[    4.633107] usb 2-1: New USB device found, idVendor=413c, idProduct=8103
[    4.633107] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    5.625453] udevd version 125 started
[    6.386329] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[    6.523873] Linux agpgart interface v0.103
[    6.565909] agpgart: Detected an Intel 915GM Chipset.
[    6.566346] agpgart: Detected 7932K stolen memory.
[    6.583439] agpgart: AGP aperture is 256M @ 0xc0000000
[    6.852553] ACPI: AC Adapter [AC] (on-line)
[    7.328626] ACPI: Battery Slot [BAT0] (battery present)
[    7.328805] ACPI: Battery Slot [BAT1] (battery absent)
[    7.328952] input: Lid Switch as /class/input/input1
[    7.340628] ACPI: Lid Switch [LID]
[    7.340750] input: Power Button (CM) as /class/input/input2
[    7.368060] ACPI: Power Button (CM) [PBTN]
[    7.368536] input: Sleep Button (CM) as /class/input/input3
[    7.396060] ACPI: Sleep Button (CM) [SBTN]
[    7.900827] ACPI: \_SB_.PCI0.IDE0.SEC0.MAST: found ejectable bay
[    7.900833] ACPI: \_SB_.PCI0.IDE0.SEC0.MAST: Adding notify handler
[    7.900863] ACPI: Error installing bay notify handler
[    7.959287] input: Video Bus as /class/input/input4
[    7.984057] ACPI: Video Device [VID] (multi-head: yes  rom: no  post: no)
[    7.984635] input: Video Bus as /class/input/input5
[    8.012058] ACPI: Video Device [VID1] (multi-head: yes  rom: no  post: no)
[    8.012258] input: Video Bus as /class/input/input6
[    8.044056] ACPI: Video Device [VID2] (multi-head: yes  rom: no  post: no)
[    8.209950] Bluetooth: Core ver 2.11
[    8.210167] NET: Registered protocol family 31
[    8.210224] Bluetooth: HCI device and connection manager initialized
[    8.210285] Bluetooth: HCI socket layer initialized
[    8.233399] Bluetooth: HCI USB driver ver 2.9
[    8.236604] usbcore: registered new interface driver hci_usb
[    8.548383] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
[    8.548524] iTCO_wdt: Found a ICH6-M TCO device (Version=2, TCOBASE=0x1060)
[    8.548614] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[    8.625837] intel_rng: FWH not detected
[    8.633503] ACPI: PCI Interrupt 0000:00:1e.3[B] -> GSI 17 (level, low) -> IRQ 17
[    8.633629] PCI: Setting latency timer of device 0000:00:1e.3 to 64
[    8.736064] MC'97 1 converters and GPIO not ready (0xff00)
[    8.736755] ACPI: PCI Interrupt 0000:00:1e.2[A] -> GSI 16 (level, low) -> IRQ 16
[    8.736884] PCI: Setting latency timer of device 0000:00:1e.2 to 64
[    8.804208] ieee80211_crypt: registered algorithm 'NULL'
[    8.849452] ieee80211: 802.11 data/management/control stack, git-1.1.13
[    8.849519] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[    8.909346] input: PC Speaker as /class/input/input7
[    8.934616] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq
[    8.934700] ipw2200: Copyright(c) 2003-2006 Intel Corporation
[    9.512895] input: PS/2 Mouse as /class/input/input8
[    9.561437] input: AlpsPS/2 ALPS GlidePoint as /class/input/input9
[    9.564028] intel8x0_measure_ac97_clock: measured 55470 usecs
[    9.564088] intel8x0: clocking to 48000
[    9.564641] Yenta: CardBus bridge found at 0000:03:01.0 [1028:0182]
[    9.564727] PCI: Bus 4, cardbus bridge: 0000:03:01.0
[    9.564785]   IO window: 0x00006000-0x000060ff
[    9.564845]   IO window: 0x00006400-0x000064ff
[    9.564905]   PREFETCH window: 0x34000000-0x343fffff
[    9.564965]   MEM window: 0x30000000-0x33ffffff
[    9.565028] Yenta: Using CSCINT to route CSC interrupts to PCI
[    9.565088] Yenta: Routing CardBus interrupts to PCI
[    9.565149] Yenta TI: socket 0000:03:01.0, mfunc 0x01111122, devctl 0x64
[    9.600109] parport_pc 00:0c: reported by Plug and Play ACPI
[    9.600238] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[    9.663721] Error: Driver 'pcspkr' is already registered, aborting...
[    9.796702] Yenta: ISA IRQ mask 0x0c78, PCI irq 19
[    9.796766] Socket status: 30000820
[    9.797821] Yenta: Raising subordinate bus# of parent bus (#03) from #04 to #07
[    9.797901] pcmcia: parent PCI bridge I/O window: 0x6000 - 0x6fff
[    9.797962] cs: IO port probe 0x6000-0x6fff: clean.
[    9.798393] pcmcia: parent PCI bridge Memory window: 0xdfc00000 - 0xdfcfffff
[    9.801291] ACPI: PCI Interrupt 0000:03:03.0[A] -> GSI 17 (level, low) -> IRQ 17
[    9.801454] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
[    9.801551] firmware: requesting ipw2200-bss.fw
[   10.201609] ipw2200: Detected geography ZZD (13 802.11bg channels, 0 802.11a channels)
[   10.432174] pccard: CardBus card inserted into slot 0
[   10.536063] sata_sil 0000:04:00.0: version 2.3
[   10.536102] sata_sil 0000:04:00.0: enabling device (0000 -> 0003)
[   10.536173] ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 19 (level, low) -> IRQ 19
[   10.536295] sata_sil 0000:04:00.0: cache line size not set.  Driver may not function
[   10.536376] sata_sil 0000:04:00.0: Applying R_ERR on DMA activate FIS errata fix
[   10.536462] PCI: Setting latency timer of device 0000:04:00.0 to 64
[   10.537577] scsi2 : sata_sil
[   10.537810] scsi3 : sata_sil
[   10.537894] ata3: SATA max UDMA/100 mmio m512@0x34080000 tf 0x34080080 irq 19
[   10.537959] ata4: SATA max UDMA/100 mmio m512@0x34080000 tf 0x340800c0 irq 19
[   10.588017] cs: IO port probe 0x100-0x3af: clean.
[   10.589773] cs: IO port probe 0x3e0-0x4ff: clean.
[   10.590543] cs: IO port probe 0x820-0x8ff: clean.
[   10.591211] cs: IO port probe 0xc00-0xcf7: clean.
[   15.896167] ata3: link is slow to respond, please be patient (ready=-19)
[   20.544166] ata3: COMRESET failed (errno=-16)
[   25.904165] ata3: link is slow to respond, please be patient (ready=-19)
[   30.552167] ata3: COMRESET failed (errno=-16)
[   35.912165] ata3: link is slow to respond, please be patient (ready=-19)
[   65.596166] ata3: COMRESET failed (errno=-16)
[   70.620178] ata3: COMRESET failed (errno=-16)
[   70.620238] ata3: reset failed, giving up
[   75.980164] ata4: link is slow to respond, please be patient (ready=-19)
[   80.628166] ata4: COMRESET failed (errno=-16)
[   85.988166] ata4: link is slow to respond, please be patient (ready=-19)
[   90.636166] ata4: COMRESET failed (errno=-16)
[   95.996166] ata4: link is slow to respond, please be patient (ready=-19)
[  125.676166] ata4: COMRESET failed (errno=-16)
[  130.700165] ata4: COMRESET failed (errno=-16)
[  130.700224] ata4: reset failed, giving up
[  131.973721] Adding 570268k swap on /dev/sda5.  Priority:-1 extents:1 across:570268k
[  132.536719] EXT3 FS on sda3, internal journal
[  132.854188] loop: module loaded
[  135.735603] NET: Registered protocol family 10
[  135.736124] lo: Disabled Privacy Extensions
[  135.736616] ADDRCONF(NETDEV_UP): eth0: link is not ready
[  136.329925] tg3: eth0: Link is up at 100 Mbps, full duplex.
[  136.329925] tg3: eth0: Flow control is off for TX and off for RX.
[  136.329925] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready



And in comparison, here is /var/log/dmesg when I boot with 2.6.25-2:


Kernel command line: root=/dev/sda3 ro 
[    0.000000] mapped APIC to ffffb000 (fee00000)
[    0.000000] mapped IOAPIC to ffffa000 (fec00000)
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[    0.000000] Detected 1729.022 MHz processor.
[    0.001508] Console: colour VGA+ 80x25
[    0.001512] console [tty0] enabled
[    0.004000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.004000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.004000] Memory: 501320k/515908k available (1753k kernel code, 14044k reserved, 728k data, 252k init, 0k highmem)
[    0.004000] virtual kernel memory layout:
[    0.004000]     fixmap  : 0xfff4c000 - 0xfffff000   ( 716 kB)
[    0.004000]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[    0.004000]     vmalloc : 0xe0000000 - 0xff7fe000   ( 503 MB)
[    0.004000]     lowmem  : 0xc0000000 - 0xdf7d1000   ( 503 MB)
[    0.004000]       .init : 0xc0375000 - 0xc03b4000   ( 252 kB)
[    0.004000]       .data : 0xc02b649a - 0xc036c640   ( 728 kB)
[    0.004000]       .text : 0xc0100000 - 0xc02b649a   (1753 kB)
[    0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[    0.084009] Calibrating delay using timer specific routine.. 3462.08 BogoMIPS (lpj=6924179)
[    0.084155] Security Framework initialized
[    0.084215] SELinux:  Disabled at boot.
[    0.084271] Capability LSM initialized
[    0.084339] Mount-cache hash table entries: 512
[    0.084530] Initializing cgroup subsys ns
[    0.084587] Initializing cgroup subsys cpuacct
[    0.084662] CPU: L1 I cache: 32K, L1 D cache: 32K
[    0.084749] CPU: L2 cache: 2048K
[    0.084804] Intel machine check architecture supported.
[    0.084864] Intel machine check reporting enabled on CPU#0.
[    0.084923] Compat vDSO mapped to ffffe000.
[    0.084982] Checking 'hlt' instruction... OK.
[    0.100348] SMP alternatives: switching to UP code
[    0.102460] Freeing SMP alternatives: 16k freed
[    0.102517] ACPI: Core revision 20070126
[    0.112044] CPU0: Intel(R) Pentium(R) M processor 1.73GHz stepping 08
[    0.112185] Total of 1 processors activated (3462.08 BogoMIPS).
[    0.112431] ENABLING IO-APIC IRQs
[    0.112673] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.156009] Brought up 1 CPUs
[    0.156009] CPU0 attaching sched-domain:
[    0.156009]  domain 0: span 01
[    0.156009]   groups: 01
[    0.156009] net_namespace: 548 bytes
[    0.156009] Booting paravirtualized kernel on bare hardware
[    0.156009] NET: Registered protocol family 16
[    0.156009] ACPI: bus type pci registered
[    0.156009] PCI: Using MMCONFIG for extended config space
[    0.156009] PCI: Using configuration type 1
[    0.156009] Setting up standard PCI resources
[    0.156010] ACPI: EC: Look up EC in DSDT
[    0.176652] ACPI: SSDT 1F7D1FD0, 0043 (r1  LMPWR  DELLLOM     1001 INTL 20030522)
[    0.176914] ACPI: Interpreter enabled
[    0.176970] ACPI: (supports S0 S3 S4 S5)
[    0.177156] ACPI: Using IOAPIC for interrupt routing
[    0.216352] ACPI: PCI Root Bridge [PCI0] (0000:00)
[    0.217128] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
[    0.217135] pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
[    0.217216] pci 0000:00:1f.0: quirk: region 1080-10bf claimed by ICH6 GPIO
[    0.217779] PCI: Transparent bridge - 0000:00:1e.0
[    0.217883] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.218347] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT]
[    0.260330] ACPI: PCI Interrupt Link [LNKA] (IRQs 9 10 *11)
[    0.260661] ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7) *10
[    0.260990] ACPI: PCI Interrupt Link [LNKC] (IRQs *9 10 11)
[    0.261323] ACPI: PCI Interrupt Link [LNKD] (IRQs *5 7 9 10 11)
[    0.261698] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[    0.264199] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[    0.264834] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[    0.265550] Linux Plug and Play Support v0.97 (c) Adam Belay
[    0.265636] pnp: PnP ACPI init
[    0.265693] ACPI: bus type pnp registered
[    0.325687] pnpacpi: exceeded the max number of IO resources: 40 
[    0.332100] pnp: PnP ACPI: found 15 devices
[    0.332156] ACPI: ACPI bus type pnp unregistered
[    0.332213] PnPBIOS: Disabled by ACPI PNP
[    0.332472] PCI: Using ACPI for IRQ routing
[    0.332528] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[    0.332851] hpet clockevent registered
[    0.332858] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.333038] hpet0: 3 64-bit timers, 14318180 Hz
[    0.334143] system 00:00: iomem range 0x0-0x9fbff could not be reserved
[    0.334205] system 00:00: iomem range 0x9fc00-0x9ffff could not be reserved
[    0.334267] system 00:00: iomem range 0xc0000-0xcffff could not be reserved
[    0.334330] system 00:00: iomem range 0xe0000-0xfffff could not be reserved
[    0.334392] system 00:00: iomem range 0x100000-0x1f7d17ff could not be reserved
[    0.334471] system 00:00: iomem range 0x1f7d1800-0x1f7fffff could not be reserved
[    0.334550] system 00:00: iomem range 0x1f800000-0x1fffffff could not be reserved
[    0.334629] system 00:00: iomem range 0xfeda0000-0xfedfffff could not be reserved
[    0.334708] system 00:00: iomem range 0xffb00000-0xffffffff could not be reserved
[    0.334787] system 00:00: iomem range 0xfec00000-0xfec0ffff could not be reserved
[    0.334866] system 00:00: iomem range 0xfee00000-0xfee0ffff could not be reserved
[    0.334946] system 00:00: iomem range 0xfed20000-0xfed9ffff could not be reserved
[    0.335025] system 00:00: iomem range 0xf0000000-0xf0003fff could not be reserved
[    0.335104] system 00:00: iomem range 0xf0004000-0xf0004fff could not be reserved
[    0.335184] system 00:00: iomem range 0xf0005000-0xf0005fff could not be reserved
[    0.335263] system 00:00: iomem range 0xf0006000-0xf0006fff could not be reserved
[    0.335341] system 00:00: iomem range 0xf0008000-0xf000bfff could not be reserved
[    0.335420] system 00:00: iomem range 0xe0000000-0xefffffff could not be reserved
[    0.335502] system 00:02: ioport range 0x4d0-0x4d1 has been reserved
[    0.335563] system 00:02: ioport range 0x1000-0x1005 has been reserved
[    0.335629] system 00:02: ioport range 0x1008-0x100f has been reserved
[    0.335693] system 00:03: ioport range 0xf400-0xf4fe has been reserved
[    0.335755] system 00:03: ioport range 0x1006-0x1007 has been reserved
[    0.335816] system 00:03: ioport range 0x100a-0x1059 could not be reserved
[    0.335878] system 00:03: ioport range 0x1060-0x107f has been reserved
[    0.335939] system 00:03: ioport range 0x1080-0x10bf has been reserved
[    0.336001] system 00:03: ioport range 0x10c0-0x10df has been reserved
[    0.336023] system 00:03: ioport range 0x10e0-0x10ff has been reserved
[    0.337051] system 00:08: ioport range 0x900-0x90f has been reserved
[    0.337112] system 00:08: ioport range 0x910-0x91f has been reserved
[    0.337173] system 00:08: ioport range 0x920-0x92f has been reserved
[    0.337234] system 00:08: ioport range 0x93c-0x93f has been reserved
[    0.337294] system 00:08: ioport range 0x940-0x97f has been reserved
[    0.337358] system 00:0d: ioport range 0x930-0x93b has been reserved
[    0.337421] system 00:0e: ioport range 0x7b0-0x7bb has been reserved
[    0.337482] system 00:0e: ioport range 0x7c0-0x7df has been reserved
[    0.337544] system 00:0e: ioport range 0xbb0-0xbbb has been reserved
[    0.337605] system 00:0e: ioport range 0xbc0-0xbdf has been reserved
[    0.337666] system 00:0e: ioport range 0xfb0-0xfbb has been reserved
[    0.337726] system 00:0e: ioport range 0xfc0-0xfdf has been reserved
[    0.337787] system 00:0e: ioport range 0x13b0-0x13bb has been reserved
[    0.337849] system 00:0e: ioport range 0x13c0-0x13df has been reserved
[    0.337910] system 00:0e: ioport range 0x17b0-0x17bb has been reserved
[    0.337971] system 00:0e: ioport range 0x17c0-0x17df has been reserved
[    0.338033] system 00:0e: ioport range 0x1bb0-0x1bbb has been reserved
[    0.338094] system 00:0e: ioport range 0x1bc0-0x1bdf has been reserved
[    0.338156] system 00:0e: ioport range 0x1fb0-0x1fbb has been reserved
[    0.338218] system 00:0e: ioport range 0x1fc0-0x1fdf has been reserved
[    0.338279] system 00:0e: ioport range 0x23b0-0x23bb has been reserved
[    0.338341] system 00:0e: ioport range 0x23c0-0x23df has been reserved
[    0.338402] system 00:0e: ioport range 0x27b0-0x27bb has been reserved
[    0.338464] system 00:0e: ioport range 0x27c0-0x27df has been reserved
[    0.338525] system 00:0e: ioport range 0x2bb0-0x2bbb has been reserved
[    0.338586] system 00:0e: ioport range 0x2bc0-0x2bdf has been reserved
[    0.338647] system 00:0e: ioport range 0x2fb0-0x2fbb has been reserved
[    0.338709] system 00:0e: ioport range 0x2fc0-0x2fdf has been reserved
[    0.338771] system 00:0e: ioport range 0x33b0-0x33bb has been reserved
[    0.338832] system 00:0e: ioport range 0x33c0-0x33df has been reserved
[    0.338894] system 00:0e: ioport range 0x37b0-0x37bb has been reserved
[    0.338955] system 00:0e: ioport range 0x37c0-0x37df has been reserved
[    0.339016] system 00:0e: ioport range 0x3bb0-0x3bbb has been reserved
[    0.339078] system 00:0e: ioport range 0x3bc0-0x3bdf has been reserved
[    0.339139] system 00:0e: ioport range 0x3fb0-0x3fbb has been reserved
[    0.339201] system 00:0e: ioport range 0x3fc0-0x3fdf has been reserved
[    0.339262] system 00:0e: ioport range 0x43b0-0x43bb has been reserved
[    0.339323] system 00:0e: ioport range 0x43c0-0x43df has been reserved
[    0.339385] system 00:0e: ioport range 0x47b0-0x47bb has been reserved
[    0.339446] system 00:0e: ioport range 0x47c0-0x47df has been reserved
[    0.339508] system 00:0e: ioport range 0x4bb0-0x4bbb has been reserved
[    0.339569] system 00:0e: ioport range 0x4bc0-0x4bdf has been reserved
[    0.339631] system 00:0e: ioport range 0x4fb0-0x4fbb has been reserved
[    0.339692] system 00:0e: ioport range 0x4fc0-0x4fdf has been reserved
[    0.339753] system 00:0e: ioport range 0x53b0-0x53bb has been reserved
[    0.339815] system 00:0e: ioport range 0x53c0-0x53df has been reserved
[    0.370309] PCI: Bridge: 0000:00:1c.0
[    0.370364]   IO window: disabled.
[    0.370422]   MEM window: 0xdfd00000-0xdfdfffff
[    0.370481]   PREFETCH window: disabled.
[    0.370547] PCI: Bus 4, cardbus bridge: 0000:03:01.0
[    0.370604]   IO window: 0x00006000-0x000060ff
[    0.370664]   IO window: 0x00006400-0x000064ff
[    0.370723]   PREFETCH window: 0x30000000-0x33ffffff
[    0.370784]   MEM window: 0x34000000-0x37ffffff
[    0.370843] PCI: Bridge: 0000:00:1e.0
[    0.370899]   IO window: 6000-6fff
[    0.370956]   MEM window: 0xdfc00000-0xdfcfffff
[    0.371015]   PREFETCH window: 0x0000000030000000-0x0000000033ffffff
[    0.371102] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
[    0.371215] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[    0.371228] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[    0.371244] PCI: Enabling device 0000:03:01.0 (0000 -> 0003)
[    0.371305] ACPI: PCI Interrupt 0000:03:01.0[A] -> GSI 19 (level, low) -> IRQ 19
[    0.371433] NET: Registered protocol family 2
[    0.371567] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.371809] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    0.371987] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[    0.372123] TCP: Hash tables configured (established 16384 bind 16384)
[    0.372185] TCP reno registered
[    0.372387] checking if image is initramfs... it is
[    0.840058] Switched to high resolution mode on CPU 0
[    0.969320] Freeing initrd memory: 6443k freed
[    0.970092] audit: initializing netlink socket (disabled)
[    0.970169] type=2000 audit(1228766037.964:1): initialized
[    0.970350] Total HugeTLB memory allocated, 0
[    0.970479] VFS: Disk quotas dquot_6.5.1
[    0.970559] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.970720] io scheduler noop registered
[    0.970775] io scheduler anticipatory registered
[    0.970832] io scheduler deadline registered
[    0.970900] io scheduler cfq registered (default)
[    0.970970] pci 0000:00:02.0: Boot video device
[    0.971165] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[    0.971210] assign_interrupt_mode Found MSI capability
[    0.971313] Allocate Port Service[0000:00:1c.0:pcie00]
[    0.971354] Allocate Port Service[0000:00:1c.0:pcie02]
[    0.971391] Allocate Port Service[0000:00:1c.0:pcie03]
[    0.971708] isapnp: Scanning for PnP cards...
[    1.326992] isapnp: No Plug & Play device found
[    1.329495] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[    1.329715] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.330229] 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.330416] ACPI: PCI Interrupt 0000:00:1e.3[B] -> GSI 17 (level, low) -> IRQ 17
[    1.330531] ACPI: PCI interrupt for device 0000:00:1e.3 disabled
[    1.331305] brd: module loaded
[    1.331446] PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    1.336569] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.336631] serio: i8042 AUX port at 0x60,0x64 irq 12
[    1.336817] mice: PS/2 mouse device common for all mice
[    1.336927] cpuidle: using governor ladder
[    1.336983] cpuidle: using governor menu
[    1.337420] TCP cubic registered
[    1.337486] NET: Registered protocol family 1
[    1.337550] NET: Registered protocol family 17
[    1.337612] Using IPI No-Shortcut mode
[    1.337784] registered taskstats version 1
[    1.338085] Freeing unused kernel memory: 252k freed
[    1.342419] input: AT Translated Set 2 keyboard as /class/input/input0
[    1.417577] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3])
[    1.417850] ACPI: ACPI0007:00 is registered as cooling_device0
[    1.417911] ACPI: Processor [CPU0] (supports 8 throttling states)
[    1.420833] ACPI: LNXTHERM:01 is registered as thermal_zone0
[    1.422456] ACPI: Thermal Zone [THM] (59 C)
[    1.899332] ACPI: ACPI Dock Station Driver 
[    1.931288] tg3.c:v3.91 (April 18, 2008)
[    1.931379] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[    1.931496] PCI: Setting latency timer of device 0000:02:00.0 to 64
[    1.952962] eth0: Tigon3 [partno(BCM95751) rev 4001 PHY(5750)] (PCI Express) 10/100/1000Base-T Ethernet 00:15:c5:21:30:61
[    1.953055] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
[    1.953134] eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[    1.968070] usbcore: registered new interface driver usbfs
[    1.968157] usbcore: registered new interface driver hub
[    1.979217] usbcore: registered new device driver usb
[    1.991385] USB Universal Host Controller Interface driver v3.0
[    1.991487] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16
[    1.991608] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[    1.991612] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    1.991802] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[    1.991913] uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000bf80
[    1.992090] usb usb1: configuration #1 chosen from 1 choice
[    1.992151] hub 1-0:1.0: USB hub found
[    1.992210] hub 1-0:1.0: 2 ports detected
[    2.096233] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[    2.096302] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.096381] usb usb1: Product: UHCI Host Controller
[    2.096438] usb usb1: Manufacturer: Linux 2.6.25-2-686 uhci_hcd
[    2.096497] usb usb1: SerialNumber: 0000:00:1d.0
[    2.096588] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 17
[    2.096708] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[    2.096712] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    2.096793] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[    2.096905] uhci_hcd 0000:00:1d.1: irq 17, io base 0x0000bf60
[    2.097066] usb usb2: configuration #1 chosen from 1 choice
[    2.097145] hub 2-0:1.0: USB hub found
[    2.097204] hub 2-0:1.0: 2 ports detected
[    2.101888] SCSI subsystem initialized
[    2.130729] libata version 3.00 loaded.
[    2.200226] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    2.200296] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.200374] usb usb2: Product: UHCI Host Controller
[    2.200431] usb usb2: Manufacturer: Linux 2.6.25-2-686 uhci_hcd
[    2.200491] usb usb2: SerialNumber: 0000:00:1d.1
[    2.200587] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[    2.200707] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[    2.200711] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    2.200792] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[    2.200901] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000bf40
[    2.201065] usb usb3: configuration #1 chosen from 1 choice
[    2.201144] hub 3-0:1.0: USB hub found
[    2.201204] hub 3-0:1.0: 2 ports detected
[    2.236140] Marking TSC unstable due to: TSC halts in idle.
[    2.300676] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    2.300739] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.300816] usb usb3: Product: UHCI Host Controller
[    2.300873] usb usb3: Manufacturer: Linux 2.6.25-2-686 uhci_hcd
[    2.300933] usb usb3: SerialNumber: 0000:00:1d.2
[    2.301022] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 19
[    2.301140] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[    2.301144] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    2.301224] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[    2.302312] uhci_hcd 0000:00:1d.3: irq 19, io base 0x0000bf20
[    2.302473] usb usb4: configuration #1 chosen from 1 choice
[    2.302553] hub 4-0:1.0: USB hub found
[    2.302612] hub 4-0:1.0: 2 ports detected
[    2.332359] Clocksource tsc unstable (delta = -92009530 ns)
[    2.332427] usb 1-2: new full speed USB device using uhci_hcd and address 2
[    2.404190] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    2.404252] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.404330] usb usb4: Product: UHCI Host Controller
[    2.404387] usb usb4: Manufacturer: Linux 2.6.25-2-686 uhci_hcd
[    2.404446] usb usb4: SerialNumber: 0000:00:1d.3
[    2.404556] ahci 0000:00:1f.2: version 3.0
[    2.404577] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level, low) -> IRQ 17
[    2.404695] ACPI: PCI interrupt for device 0000:00:1f.2 disabled
[    2.404757] ahci: probe of 0000:00:1f.2 failed with error -22
[    2.406838] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 16 (level, low) -> IRQ 16
[    2.406955] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[    2.406959] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    2.407037] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
[    2.411050] ehci_hcd 0000:00:1d.7: debug port 1
[    2.411110] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[    2.411116] ehci_hcd 0000:00:1d.7: irq 16, io mem 0xffa80800
[    2.456150] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[    2.456339] usb usb5: configuration #1 chosen from 1 choice
[    2.456423] hub 5-0:1.0: USB hub found
[    2.456484] hub 5-0:1.0: 8 ports detected
[    2.560158] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[    2.560228] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.560306] usb usb5: Product: EHCI Host Controller
[    2.560363] usb usb5: Manufacturer: Linux 2.6.25-2-686 ehci_hcd
[    2.560423] usb usb5: SerialNumber: 0000:00:1d.7
[    2.564177] ata_piix 0000:00:1f.2: version 2.12
[    2.564191] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level, low) -> IRQ 17
[    2.564304] ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
[    2.719698] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[    2.719870] scsi0 : ata_piix
[    2.720115] scsi1 : ata_piix
[    2.722083] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xbfa0 irq 14
[    2.722145] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xbfa8 irq 15
[    2.851416] usb 1-2: device not accepting address 2, error -71
[    2.884070] ata1.00: ATA-6: TOSHIBA MK4032GAX, AD102D, max UDMA/100
[    2.884131] ata1.00: 78140160 sectors, multi 8: LBA48 
[    2.884189] ata1.00: applying bridge limits
[    2.892031] ata1.00: configured for UDMA/100
[    2.907223] hub 1-0:1.0: unable to enumerate USB device on port 2
[    3.210778] ata2.00: ATAPI: HL-DT-ST DVD-ROM GDR-8084N, 1.01, max UDMA/33
[    3.274189] usb 5-2: new high speed USB device using ehci_hcd and address 2
[    3.382265] ata2.00: configured for UDMA/33
[    3.382436] scsi 0:0:0:0: Direct-Access     ATA      TOSHIBA MK4032GA AD10 PQ: 0 ANSI: 5
[    3.386816] scsi 1:0:0:0: CD-ROM            HL-DT-ST DVD-ROM GDR8084N 1.01 PQ: 0 ANSI: 5
[    3.393549] Uniform Multi-Platform E-IDE driver
[    3.393612] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[    3.406332] usb 5-2: configuration #1 chosen from 1 choice
[    3.406508] hub 5-2:1.0: USB hub found
[    3.406612] hub 5-2:1.0: 4 ports detected
[    3.424591] Driver 'sd' needs updating - please use bus_type methods
[    3.424749] sd 0:0:0:0: [sda] 78140160 512-byte hardware sectors (40008 MB)
[    3.424829] sd 0:0:0:0: [sda] Write Protect is off
[    3.424887] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    3.424919] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.425063] sd 0:0:0:0: [sda] 78140160 512-byte hardware sectors (40008 MB)
[    3.425141] sd 0:0:0:0: [sda] Write Protect is off
[    3.425198] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    3.425230] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.425312]  sda:<4>Driver 'sr' needs updating - please use bus_type methods
[    3.460964]  sda1 sda2 sda3 sda4 < sda5 >
[    3.487602] sd 0:0:0:0: [sda] Attached SCSI disk
[    3.497019] sr0: scsi3-mmc drive: 24x/24x cd/rw xa/form2 cdda tray
[    3.497086] Uniform CD-ROM driver Revision: 3.20
[    3.497197] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    3.508277] usb 5-2: New USB device found, idVendor=413c, idProduct=0058
[    3.508344] usb 5-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    3.509493] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    3.509600] sr 1:0:0:0: Attached scsi generic sg1 type 5
[    3.733620] hub 5-0:1.0: unable to enumerate USB device on port 3
[    3.753308] md: raid1 personality registered for level 1
[    3.760777] md: md0 stopped.
[    3.786355] device-mapper: uevent: version 1.0.3
[    3.787539] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
[    3.798935] PM: Starting manual resume from disk
[    3.838049] kjournald starting.  Commit interval 5 seconds
[    3.838049] EXT3-fs: mounted filesystem with ordered data mode.
[    3.919823] usb 5-2.1: new high speed USB device using ehci_hcd and address 4
[    4.010971] usb 5-2.1: configuration #1 chosen from 1 choice
[    4.011131] hub 5-2.1:1.0: USB hub found
[    4.011223] hub 5-2.1:1.0: 4 ports detected
[    4.112540] usb 5-2.1: New USB device found, idVendor=0424, idProduct=2504
[    4.112602] usb 5-2.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    4.348055] usb 2-1: new full speed USB device using uhci_hcd and address 2
[    4.534085] usb 2-1: configuration #1 chosen from 1 choice
[    4.537937] usb 2-1: New USB device found, idVendor=413c, idProduct=8103
[    4.537937] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    5.748501] udevd version 125 started
[    6.452384] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[    6.622137] Linux agpgart interface v0.103
[    6.669352] agpgart: Detected an Intel 915GM Chipset.
[    6.669784] agpgart: Detected 7932K stolen memory.
[    6.686839] agpgart: AGP aperture is 256M @ 0xc0000000
[    7.024569] ACPI: AC Adapter [AC] (on-line)
[    7.329689] ACPI: Battery Slot [BAT0] (battery present)
[    7.329802] ACPI: Battery Slot [BAT1] (battery absent)
[    7.329950] input: Lid Switch as /class/input/input1
[    7.341718] ACPI: Lid Switch [LID]
[    7.341826] input: Power Button (CM) as /class/input/input2
[    7.369154] ACPI: Power Button (CM) [PBTN]
[    7.369268] input: Sleep Button (CM) as /class/input/input3
[    7.397149] ACPI: Sleep Button (CM) [SBTN]
[    7.966742] ACPI: \_SB_.PCI0.IDE0.SEC0.MAST: found ejectable bay
[    7.966748] ACPI: \_SB_.PCI0.IDE0.SEC0.MAST: Adding notify handler
[    7.966778] ACPI: Error installing bay notify handler
[    7.966843] ACPI: Bay [\_SB_.PCI0.IDE0.SEC0.MAST] Added
[    8.031279] input: Video Bus as /class/input/input4
[    8.057194] ACPI: Video Device [VID] (multi-head: yes  rom: no  post: no)
[    8.057746] input: Video Bus as /class/input/input5
[    8.089206] ACPI: Video Device [VID1] (multi-head: yes  rom: no  post: no)
[    8.089420] input: Video Bus as /class/input/input6
[    8.121200] ACPI: Video Device [VID2] (multi-head: yes  rom: no  post: no)
[    8.220311] Bluetooth: Core ver 2.11
[    8.254427] NET: Registered protocol family 31
[    8.254487] Bluetooth: HCI device and connection manager initialized
[    8.254549] Bluetooth: HCI socket layer initialized
[    8.296211] Bluetooth: HCI USB driver ver 2.9
[    8.299020] usbcore: registered new interface driver hci_usb
[    8.567724] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
[    8.567866] iTCO_wdt: Found a ICH6-M TCO device (Version=2, TCOBASE=0x1060)
[    8.567954] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[    8.725834] intel_rng: FWH not detected
[    8.854414] Yenta: CardBus bridge found at 0000:03:01.0 [1028:0182]
[    8.854502] Yenta: Using CSCINT to route CSC interrupts to PCI
[    8.854561] Yenta: Routing CardBus interrupts to PCI
[    8.854622] Yenta TI: socket 0000:03:01.0, mfunc 0x01111122, devctl 0x64
[    8.922967] input: PC Speaker as /class/input/input7
[    8.996759] ieee80211_crypt: registered algorithm 'NULL'
[    9.016444] ieee80211: 802.11 data/management/control stack, git-1.1.13
[    9.016511] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[    9.086012] Yenta: ISA IRQ mask 0x0cf8, PCI irq 19
[    9.086077] Socket status: 30000820
[    9.086132] Yenta: Raising subordinate bus# of parent bus (#03) from #04 to #07
[    9.086212] pcmcia: parent PCI bridge I/O window: 0x6000 - 0x6fff
[    9.086303] cs: IO port probe 0x6000-0x6fff: clean.
[    9.086725] pcmcia: parent PCI bridge Memory window: 0xdfc00000 - 0xdfcfffff
[    9.086787] pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x33ffffff
[    9.091038] ACPI: PCI Interrupt 0000:00:1e.2[A] -> GSI 16 (level, low) -> IRQ 16
[    9.091174] PCI: Setting latency timer of device 0000:00:1e.2 to 64
[    9.116440] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq
[    9.116525] ipw2200: Copyright(c) 2003-2006 Intel Corporation
[    9.189372] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[    9.189468] rtc0: alarms up to one month, y3k
[    9.657906] input: PS/2 Mouse as /class/input/input8
[    9.706674] input: AlpsPS/2 ALPS GlidePoint as /class/input/input9
[    9.725476] pccard: CardBus card inserted into slot 0
[    9.737737] parport_pc 00:0c: reported by Plug and Play ACPI
[    9.738864] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[    9.917286] intel8x0_measure_ac97_clock: measured 55498 usecs
[    9.917351] intel8x0: clocking to 48000
[    9.917677] ACPI: PCI Interrupt 0000:03:03.0[A] -> GSI 17 (level, low) -> IRQ 17
[    9.917856] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
[   10.140503] cs: IO port probe 0x100-0x3af: clean.
[   10.141714] cs: IO port probe 0x3e0-0x4ff: clean.
[   10.142479] cs: IO port probe 0x820-0x8ff: clean.
[   10.143142] cs: IO port probe 0xc00-0xcf7: clean.
[   10.318999] ipw2200: Detected geography ZZD (13 802.11bg channels, 0 802.11a channels)
[   10.319159] sata_sil 0000:04:00.0: version 2.3
[   10.319196] PCI: Enabling device 0000:04:00.0 (0000 -> 0003)
[   10.319261] ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 19 (level, low) -> IRQ 19
[   10.319384] sata_sil 0000:04:00.0: cache line size not set.  Driver may not function
[   10.319465] sata_sil 0000:04:00.0: Applying R_ERR on DMA activate FIS errata fix
[   10.319552] PCI: Setting latency timer of device 0000:04:00.0 to 64
[   10.319631] ACPI: PCI Interrupt 0000:00:1e.3[B] -> GSI 17 (level, low) -> IRQ 17
[   10.319753] PCI: Setting latency timer of device 0000:00:1e.3 to 64
[   10.320636] scsi2 : sata_sil
[   10.321659] scsi3 : sata_sil
[   10.321752] ata3: SATA max UDMA/100 mmio m512@0x34000000 tf 0x34000080 irq 19
[   10.321816] ata4: SATA max UDMA/100 mmio m512@0x34000000 tf 0x340000c0 irq 19
[   10.422762] MC'97 1 converters and GPIO not ready (0xff00)
[   10.783457] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[   10.792239] ata3.00: ATA-7: SAMSUNG HA250JC, WE100-33, max UDMA/133
[   10.792301] ata3.00: 488397168 sectors, multi 0: LBA48 
[   10.792359] ata3.00: applying bridge limits
[   10.808192] ata3.00: configured for UDMA/100
[   11.272308] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[   11.319988] ata4.00: NODEV after polling detection
[   11.320123] scsi 2:0:0:0: Direct-Access     ATA      SAMSUNG HA250JC  WE10 PQ: 0 ANSI: 5
[   11.320294] sd 2:0:0:0: [sdb] 488397168 512-byte hardware sectors (250059 MB)
[   11.320376] sd 2:0:0:0: [sdb] Write Protect is off
[   11.320433] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[   11.320466] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   11.320611] sd 2:0:0:0: [sdb] 488397168 512-byte hardware sectors (250059 MB)
[   11.320689] sd 2:0:0:0: [sdb] Write Protect is off
[   11.320746] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[   11.320778] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   11.320860]  sdb: unknown partition table
[   11.336198] sd 2:0:0:0: [sdb] Attached SCSI disk
[   11.336198] sd 2:0:0:0: Attached scsi generic sg2 type 0
[   12.246855] Adding 570268k swap on /dev/sda5.  Priority:-1 extents:1 across:570268k
[   12.799102] EXT3 FS on sda3, internal journal
[   12.982678] loop: module loaded
[   15.646366] NET: Registered protocol family 10
[   15.646906] lo: Disabled Privacy Extensions
[   15.647395] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   16.265591] tg3: eth0: Link is up at 100 Mbps, full duplex.
[   16.265591] tg3: eth0: Flow control is off for TX and off for RX.
[   16.265591] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready



-- Package-specific info:

-- System Information:
Debian Release: lenny/sid
  APT prefers testing
  APT policy: (500, 'testing')
Architecture: i386 (i686)

Kernel: Linux 2.6.25-2-686 (SMP w/1 CPU core)
Locale: LANG=fr_FR.UTF-8, LC_CTYPE=fr_FR.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash

Versions of packages linux-image-2.6.26-1-686 depends on:
ii  debconf [debconf-2.0]         1.5.24     Debian configuration management sy
ii  initramfs-tools [linux-initra 0.92j      tools for generating an initramfs
ii  module-init-tools             3.4-1      tools for managing Linux kernel mo

Versions of packages linux-image-2.6.26-1-686 recommends:
ii  libc6-i686                    2.7-16     GNU C Library: Shared libraries [i

Versions of packages linux-image-2.6.26-1-686 suggests:
ii  grub                          0.97-47    GRand Unified Bootloader (Legacy v
pn  linux-doc-2.6.26              <none>     (no description available)

-- debconf information:
  linux-image-2.6.26-1-686/preinst/abort-overwrite-2.6.26-1-686:
  shared/kernel-image/really-run-bootloader: true
  linux-image-2.6.26-1-686/postinst/bootloader-error-2.6.26-1-686:
  linux-image-2.6.26-1-686/postinst/depmod-error-initrd-2.6.26-1-686: false
  linux-image-2.6.26-1-686/prerm/removing-running-kernel-2.6.26-1-686: true
  linux-image-2.6.26-1-686/postinst/old-system-map-link-2.6.26-1-686: true
  linux-image-2.6.26-1-686/preinst/abort-install-2.6.26-1-686:
  linux-image-2.6.26-1-686/preinst/lilo-has-ramdisk:
  linux-image-2.6.26-1-686/preinst/bootloader-initrd-2.6.26-1-686: true
  linux-image-2.6.26-1-686/prerm/would-invalidate-boot-loader-2.6.26-1-686: true
  linux-image-2.6.26-1-686/preinst/elilo-initrd-2.6.26-1-686: true
  linux-image-2.6.26-1-686/postinst/kimage-is-a-directory:
  linux-image-2.6.26-1-686/postinst/old-dir-initrd-link-2.6.26-1-686: true
  linux-image-2.6.26-1-686/postinst/create-kimage-link-2.6.26-1-686: true
  linux-image-2.6.26-1-686/preinst/lilo-initrd-2.6.26-1-686: true
  linux-image-2.6.26-1-686/postinst/old-initrd-link-2.6.26-1-686: true
  linux-image-2.6.26-1-686/preinst/overwriting-modules-2.6.26-1-686: true
  linux-image-2.6.26-1-686/postinst/depmod-error-2.6.26-1-686: false
  linux-image-2.6.26-1-686/postinst/bootloader-test-error-2.6.26-1-686:
  linux-image-2.6.26-1-686/preinst/failed-to-move-modules-2.6.26-1-686:
  linux-image-2.6.26-1-686/preinst/initrd-2.6.26-1-686:



--- End Message ---
--- Begin Message ---
On Thu, Sep 10, 2009 at 10:41:49PM +0200, Moritz Muehlenhoff wrote:
> On Mon, Dec 08, 2008 at 10:04:03PM -0500, Jerome wrote:
> > Package: linux-image-2.6.26-1-686
> > Version: 2.6.26-11
> > Severity: important
> > 
> > 
> > My two SAMSUNG HA250JC hard drives were working fine until apt-get upgraded
> > the kernel from 2.6.25-2 to 2.6.26-1 (Debian testing).
> > 
> > Both hard drives are plugged externally to my laptop through a PCMCIA card with 2 eSATA ports.
> > 
> > The following excerpt from /var/log/dmesg might be be relevant when I boot with 2.6.26-1:
> > 
> > [   15.896167] ata3: link is slow to respond, please be patient (ready=-19)
> > [   20.544166] ata3: COMRESET failed (errno=-16)
> > [   25.904165] ata3: link is slow to respond, please be patient (ready=-19)
> > [   30.552167] ata3: COMRESET failed (errno=-16)
> > [   35.912165] ata3: link is slow to respond, please be patient (ready=-19)
> > [   65.596166] ata3: COMRESET failed (errno=-16)
> > [   70.620178] ata3: COMRESET failed (errno=-16)
> > [   70.620238] ata3: reset failed, giving up
> > 
> > With 2.6.25-2, I am getting the following result:
> > 
> > [   92.236169] ata3: hard resetting link
> > [   97.837264] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
> > [   97.845734] ata3.00: ATA-7: SAMSUNG HA250JC, WE100-33, max UDMA/133
> > [   97.845740] ata3.00: 488397168 sectors, multi 0: LBA48 
> > [   97.845743] ata3.00: applying bridge limits
> > [   97.861619] ata3.00: configured for UDMA/100
> > [   97.861633] ata3: EH complete
> > [   97.861747] scsi 2:0:0:0: Direct-Access     ATA      SAMSUNG HA250JC  WE10 PQ: 0 ANSI: 5
> > [   97.865796] sd 2:0:0:0: [sdb] 488397168 512-byte hardware sectors (250059 MB)
> > [   97.868908] sd 2:0:0:0: [sdb] Write Protect is off
> > [   97.872926] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> > [   97.873268] sd 2:0:0:0: [sdb] 488397168 512-byte hardware sectors (250059 MB)
> > [   97.876079] sd 2:0:0:0: [sdb] Write Protect is off
> > [   97.879716] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> > [   97.890512] sd 2:0:0:0: [sdb] Attached SCSI disk
> > [   97.890553] sd 2:0:0:0: Attached scsi generic sg2 type 0
> > 
> > 
> > I found a few similar reports; maybe there are related:
> > http://bugs.archlinux.org/task/11388
> > http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=501023
> > 
> > which pointed me to an on-going patch, maybe related too: 
> > http://article.gmane.org/gmane.linux.ide/34077/raw
> > 
> > If you want further information, do not hesitate to ask, I can reproduce the problem.
> > This bug prevents me from upgrading to 2.6.26.
> 
> #501023 was fixed in a Lenny point release (2.6.26-18). Does it fix the error
> for you?

No further feedback, closing the bug.

If this can be reproduced with current kernels or latest Lenny,
please reopen this bug.

Cheers,
        Moritz










--- End Message ---

Reply to: