--- Begin Message ---
- To: submit@bugs.debian.org
- Subject: Intel T3200 system only boots with 'nosmp' kernel option
- From: Peter <peter@zorbas.de>
- Date: Tue, 18 Nov 2008 23:57:29 +0100
- Message-id: <1227049049.3348.8.camel@ElkesLaptop.daheim>
Package: linux-image-2.6.26-1-686
Version: 2.6.26-10
Severity: important
*** Please type your report below this line ***
Without 'nosmp' system hangs immediatly. No log is written. Maybe the
problem is the quite new CPU:
The Laptop has a T3200 processor, all I found out about it is:
The Intel(R) Pentium(R) Dual-Core Mobile Processor T3200 is a dual core
processor; it is part of the Intel(R) Pentium(R) Dual-Core Mobile
family.
CPU speed: 2.00GHz
L2 Cache Size: 1MB
Bus Speed: 667MHz
Processor architecture: 32 bits
The system works fine with 'nosmp', however, only on one CPU. I would
appreciate to get a solution for using both CPUs.
Regards,
Peter
-- Package-specific info:
** Version:
Linux version 2.6.26-1-686 (Debian 2.6.26-10) (waldi@debian.org) (gcc
version 4.1.3 20080623 (prerelease) (Debian 4.1.2-23)) #1 SMP Sat Nov 8
19:00:26 UTC 2008
** Command line:
root=/dev/sda3 ro quiet vga=0x305 nosmp
** Not tainted
** Kernel log:
[ 3.455027] ata4: SATA max UDMA/133 cmd 0x1c48 ctl 0x1c40 bmdma
0x1c38 irq 11
[ 3.783188] ata3: SATA link down (SStatus 0 SControl 300)
[ 4.112041] ata4: SATA link down (SStatus 0 SControl 300)
[ 4.132861] Driver 'sd' needs updating - please use bus_type methods
[ 4.132944] sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors
(250059 MB)
[ 4.132963] sd 0:0:0:0: [sda] Write Protect is off
[ 4.132965] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.132997] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 4.133051] sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors
(250059 MB)
[ 4.133069] sd 0:0:0:0: [sda] Write Protect is off
[ 4.133071] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.133103] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 4.133107] sda:<4>Driver 'sr' needs updating - please use bus_type
methods
[ 4.144596] sda1 sda2 sda3 sda4 < sda5 >
[ 4.170626] sd 0:0:0:0: [sda] Attached SCSI disk
[ 4.389971] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw
xa/form2 cdda tray
[ 4.389971] Uniform CD-ROM driver Revision: 3.20
[ 4.389971] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 4.403023] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 4.403042] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 5.107007] PM: Starting manual resume from disk
[ 5.157666] kjournald starting. Commit interval 5 seconds
[ 5.157666] EXT3-fs: mounted filesystem with ordered data mode.
[ 6.935210] udevd version 125 started
[ 7.669502] Linux agpgart interface v0.103
[ 7.870619] agpgart: Detected an Intel Mobile Intel? GM45 Express
Chipset.
[ 7.870858] agpgart: Detected 65532K stolen memory.
[ 7.881128] agpgart: AGP aperture is 256M @ 0xd0000000
[ 8.013508] input: Power Button (FF) as /class/input/input1
[ 8.032072] ACPI: Power Button (FF) [PWRF]
[ 8.032261] input: Power Button (CM) as /class/input/input2
[ 8.064075] ACPI: Power Button (CM) [PWRB]
[ 8.064259] input: Lid Switch as /class/input/input3
[ 8.080701] ACPI: Lid Switch [LID0]
[ 8.081252] ACPI: AC Adapter [ACAD] (off-line)
[ 8.140461] usb-storage: device scan complete
[ 8.142610] scsi 2:0:0:0: Direct-Access Generic- Multi-Card
1.00 PQ: 0 ANSI: 0 CCS
[ 8.145382] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 8.145501] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 8.227244] ACPI: Battery Slot [BAT1] (battery present)
[ 8.343554] ACPI: device:06 is registered as cooling_device2
[ 8.343783] input: Video Bus as /class/input/input4
[ 8.438514] ACPI: Video Device [GFX0] (multi-head: yes rom: no
post: no)
[ 9.025441] ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 10
[ 9.025445] ACPI: PCI Interrupt 0000:00:1b.0[A] -> Link [LNKG] -> GSI
10 (level, low) -> IRQ 10
[ 9.025465] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 9.104346] ACPI: PCI Interrupt 0000:00:1f.3[C] -> Link [LNKD] -> GSI
11 (level, low) -> IRQ 11
[ 9.242632] input: PC Speaker as /class/input/input5
[ 9.493179] phy0: Selected rate control algorithm 'pid'
[ 9.590337] Registered led device: rt73usb-phy0:radio
[ 9.590351] Registered led device: rt73usb-phy0:assoc
[ 9.590366] Registered led device: rt73usb-phy0:quality
[ 9.590831] usbcore: registered new interface driver rt73usb
[ 9.933240] Synaptics Touchpad, model: 1, fw: 6.3, id: 0x81a0b2,
caps: 0xa04711/0xa00000
[ 9.974140] input: SynPS/2 Synaptics TouchPad as /class/input/input6
[ 10.620569] Adding 2658716k swap on /dev/sda5. Priority:-1 extents:1
across:2658716k
[ 10.674026] EXT3-fs warning: maximal mount count reached, running
e2fsck is recommended
[ 10.674245] EXT3 FS on sda3, internal journal
[ 10.898223] loop: module loaded
[ 12.484348] r8169: eth0: link down
[ 14.530503] NET: Registered protocol family 10
[ 14.530822] lo: Disabled Privacy Extensions
[ 14.531169] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 14.830160] lp: driver loaded but no devices found
[ 14.855586] ppdev: user-space parallel port driver
[ 18.269862] kerneloops[2758]: segfault at 0 ip b7d88443 sp bfbd6f1c
error 4 in libc-2.7.so[b7d12000+155000]
[ 18.767961] Bluetooth: Core ver 2.11
[ 18.772483] NET: Registered protocol family 31
[ 18.772488] Bluetooth: HCI device and connection manager initialized
[ 18.772490] Bluetooth: HCI socket layer initialized
[ 18.838743] Bluetooth: L2CAP ver 2.9
[ 18.838750] Bluetooth: L2CAP socket layer initialized
[ 19.005807] Bluetooth: RFCOMM socket layer initialized
[ 19.005825] Bluetooth: RFCOMM TTY layer initialized
[ 19.005828] Bluetooth: RFCOMM ver 1.8
[ 19.221020] firmware: requesting rt73.bin
[ 19.367775] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 23.101872] [drm] Initialized drm 1.1.0 20060810
[ 23.105441] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKA] -> GSI
5 (level, low) -> IRQ 5
[ 23.105450] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 23.105646] [drm] Initialized i915 1.6.0 20060119 on minor 0
[ 23.709651] set status page addr 0x03fff000
[ 48.556665] CPU0 attaching NULL sched-domain.
[ 48.559488] CPU0 attaching sched-domain:
[ 48.559539] domain 0: span 0
[ 48.559542] groups: 0
[ 51.122043] wlan0: Initial auth_alg=0
[ 51.122050] wlan0: authenticate with AP 00:06:4e:00:00:03
[ 51.123803] wlan0: RX authentication from 00:06:4e:00:00:03 (alg=0
transaction=2 status=0)
[ 51.123808] wlan0: authenticated
[ 51.123811] wlan0: associate with AP 00:06:4e:00:00:03
[ 51.126937] wlan0: RX AssocResp from 00:06:4e:00:00:03 (capab=0x431
status=0 aid=1)
[ 51.126943] wlan0: associated
[ 51.126950] wlan0: switched to short barker preamble
(BSSID=00:06:4e:00:00:03)
[ 51.128458] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 51.367235] padlock: VIA PadLock not detected.
[ 1197.058650] CPU0 attaching NULL sched-domain.
[ 1197.058910] CPU0 attaching sched-domain:
[ 1197.058914] domain 0: span 0
[ 1197.058916] groups: 0
** Loaded modules:
Module Size Used by
aes_i586 7744 2
aes_generic 29256 1 aes_i586
i915 25280 2
drm 65256 3 i915
rfcomm 28272 0
l2cap 17248 5 rfcomm
bluetooth 44900 4 rfcomm,l2cap
ppdev 6468 0
parport_pc 22500 0
lp 8164 0
parport 30988 3 ppdev,parport_pc,lp
ipv6 235300 14
acpi_cpufreq 6796 0
cpufreq_conservative 5960 0
cpufreq_ondemand 6476 1
cpufreq_powersave 1856 0
cpufreq_userspace 3172 0
cpufreq_stats 3776 0
freq_table 4224 3
acpi_cpufreq,cpufreq_ondemand,cpufreq_stats
loop 12748 0
joydev 8480 0
arc4 1824 2
ecb 2624 2
crypto_blkcipher 15236 1 ecb
pcspkr 2432 0
rt73usb 22432 0
crc_itu_t 2080 1 rt73usb
psmouse 32336 0
rt2x00usb 9792 1 rt73usb
rt2x00lib 22432 2 rt73usb,rt2x00usb
serio_raw 4740 0
firmware_class 6816 1 rt2x00lib
i2c_i801 7920 0
rfkill 5652 1 rt2x00lib
snd_hda_intel 324248 1
led_class 3908 1 rt2x00lib
i2c_core 19828 1 i2c_i801
input_polldev 3752 1 rt2x00lib
snd_pcm 62596 1 snd_hda_intel
snd_seq 41456 0
snd_timer 17800 2 snd_pcm,snd_seq
snd_seq_device 6380 1 snd_seq
mac80211 139680 2 rt2x00usb,rt2x00lib
snd 45604 7
snd_hda_intel,snd_pcm,snd_seq,snd_timer,snd_seq_device
cfg80211 21576 2 rt2x00lib,mac80211
soundcore 6368 1 snd
snd_page_alloc 7816 2 snd_hda_intel,snd_pcm
video 16400 0
output 2912 1 video
battery 10180 0
ac 4196 0
button 6064 0
intel_agp 22332 1
agpgart 28776 3 drm,intel_agp
evdev 8000 6
ext3 105416 1
jbd 39444 1 ext3
mbcache 7108 1 ext3
sg 26964 0
sr_mod 13316 0
cdrom 30176 1 sr_mod
sd_mod 22200 3
usb_storage 75936 0
ata_piix 14180 3
ata_generic 4676 0
libata 140384 2 ata_piix,ata_generic
scsi_mod 129356 5 sg,sr_mod,sd_mod,usb_storage,libata
dock 8272 1 libata
ide_pci_generic 3908 0 [permanent]
ide_core 96168 1 ide_pci_generic
r8169 23684 0
ehci_hcd 28428 0
uhci_hcd 18672 0
usbcore 118160 6
rt73usb,rt2x00usb,usb_storage,ehci_hcd,uhci_hcd
thermal 15228 0
processor 32576 3 acpi_cpufreq,thermal
fan 4164 0
thermal_sys 10856 4 video,thermal,processor,fan
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Mobile 4 Series Chipset
Memory Controller Hub [8086:2a40] (rev 07)
Subsystem: Device [1631:c219]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
Kernel modules: intel-agp
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 4
Series Chipset Integrated Graphics Controller [8086:2a42] (rev 07)
(prog-if 00 [VGA controller])
Subsystem: Device [1631:c219]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 5
Region 0: Memory at f2000000 (64-bit, non-prefetchable)
[size=4M]
Region 2: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at 1800 [size=8]
Capabilities: <access denied>
00:02.1 Display controller [0380]: Intel Corporation Mobile 4 Series
Chipset Integrated Graphics Controller [8086:2a43] (rev 07)
Subsystem: Device [1631:c219]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at f2400000 (64-bit, non-prefetchable)
[size=1M]
Capabilities: <access denied>
00:1a.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family)
USB UHCI Controller #4 [8086:2937] (rev 03) (prog-if 00 [UHCI])
Subsystem: Device [1631:c219]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 5
Region 4: I/O ports at 1820 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family)
USB UHCI Controller #5 [8086:2938] (rev 03) (prog-if 00 [UHCI])
Subsystem: Device [1631:c219]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 11
Region 4: I/O ports at 1840 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.2 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family)
USB UHCI Controller #6 [8086:2939] (rev 03) (prog-if 00 [UHCI])
Subsystem: Device [1631:c219]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 11
Region 4: I/O ports at 1860 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family)
USB2 EHCI Controller #2 [8086:293c] (rev 03) (prog-if 20 [EHCI])
Subsystem: Device [1631:c219]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 11
Region 0: Memory at f2704000 (32-bit, non-prefetchable)
[size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1b.0 Audio device [0403]: Intel Corporation 82801I (ICH9 Family) HD
Audio Controller [8086:293e] (rev 03)
Subsystem: Device [1631:c219]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f2700000 (64-bit, non-prefetchable)
[size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:1c.0 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI
Express Port 1 [8086:2940] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=03, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: f0000000-f1ffffff
Prefetchable memory behind bridge:
00000000f4000000-00000000f7ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1d.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family)
USB UHCI Controller #1 [8086:2934] (rev 03) (prog-if 00 [UHCI])
Subsystem: Device [1631:c219]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 7
Region 4: I/O ports at 1880 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family)
USB UHCI Controller #2 [8086:2935] (rev 03) (prog-if 00 [UHCI])
Subsystem: Device [1631:c219]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 11
Region 4: I/O ports at 18a0 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family)
USB UHCI Controller #3 [8086:2936] (rev 03) (prog-if 00 [UHCI])
Subsystem: Device [1631:c219]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 10
Region 4: I/O ports at 18c0 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family)
USB2 EHCI Controller #1 [8086:293a] (rev 03) (prog-if 20 [EHCI])
Subsystem: Device [1631:c219]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 7
Region 0: Memory at f2704400 (32-bit, non-prefetchable)
[size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge
[8086:2448] (rev 93) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=0a, subordinate=0a, sec-latency=0
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation ICH9M LPC Interface
Controller [8086:2919] (rev 03)
Subsystem: Device [1631:c219]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.2 IDE interface [0101]: Intel Corporation ICH9M/M-E 2 port SATA
IDE Controller [8086:2928] (rev 03) (prog-if 8f [Master SecP SecO PriP
PriO])
Subsystem: Device [1631:c219]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 11
Region 0: I/O ports at 18f8 [size=8]
Region 1: I/O ports at 180c [size=4]
Region 2: I/O ports at 18f0 [size=8]
Region 3: I/O ports at 1808 [size=4]
Region 4: I/O ports at 18e0 [size=16]
Region 5: I/O ports at 1810 [size=16]
Capabilities: <access denied>
Kernel driver in use: ata_piix
Kernel modules: ata_piix
00:1f.3 SMBus [0c05]: Intel Corporation 82801I (ICH9 Family) SMBus
Controller [8086:2930] (rev 03)
Subsystem: Device [1631:c219]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 11
Region 0: Memory at c2000000 (64-bit, non-prefetchable)
[size=256]
Region 4: I/O ports at 1c00 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801
00:1f.5 IDE interface [0101]: Intel Corporation ICH9M/M-E 2 port SATA
IDE Controller [8086:292d] (rev 03) (prog-if 85 [Master SecO PriO])
Subsystem: Device [1631:c219]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 11
Region 0: I/O ports at 1c50 [size=8]
Region 1: I/O ports at 1c44 [size=4]
Region 2: I/O ports at 1c48 [size=8]
Region 3: I/O ports at 1c40 [size=4]
Region 4: I/O ports at 1c30 [size=16]
Region 5: I/O ports at 1c20 [size=16]
Capabilities: <access denied>
Kernel driver in use: ata_piix
Kernel modules: ata_piix
02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev
02)
Subsystem: Device [1631:c219]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 222
Region 0: I/O ports at 2000 [size=256]
Region 2: Memory at f6000000 (64-bit, prefetchable) [size=4K]
Region 4: Memory at f4000000 (64-bit, prefetchable) [size=64K]
[virtual] Expansion ROM at f4020000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: r8169
Kernel modules: r8169
-- System Information:
Debian Release: lenny/sid
APT prefers testing-proposed-updates
APT policy: (500, 'testing-proposed-updates'), (500, 'unstable'),
(500, 'testing')
Architecture: i386 (i686)
Kernel: Linux 2.6.26-1-686 (SMP w/1 CPU core)
Locale: LANG=de_DE.UTF-8, LC_CTYPE=de_DE.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.26-1-686 depends on:
ii debconf [debconf-2.0] 1.5.24 Debian configuration
management sy
ii initramfs-tools [linux-initra 0.92l tools for generating an
initramfs
ii module-init-tools 3.4-1 tools for managing Linux
kernel mo
Versions of packages linux-image-2.6.26-1-686 recommends:
ii libc6-i686 2.7-16 GNU C Library: Shared
libraries [i
Versions of packages linux-image-2.6.26-1-686 suggests:
ii grub 0.97-47lenny1 GRand Unified Bootloader
(Legacy v
pn linux-doc-2.6.26 <none> (no description available)
-- debconf information excluded
--- End Message ---
--- Begin Message ---
- To: Peter <peter@zorbas.de>
- Cc: 506161-done@bugs.debian.org
- Subject: Re: Intel T3200 system only boots with 'nosmp' kernel option
- From: Moritz Muehlenhoff <jmm@inutil.org>
- Date: Sun, 14 Feb 2010 13:10:02 +0100
- Message-id: <20100214121002.GA21158@galadriel.inutil.org>
- In-reply-to: <1227049049.3348.8.camel@ElkesLaptop.daheim>
- References: <1227049049.3348.8.camel@ElkesLaptop.daheim>
On Tue, Nov 18, 2008 at 11:57:29PM +0100, Peter wrote:
> Package: linux-image-2.6.26-1-686
> Version: 2.6.26-10
> Severity: important
>
> *** Please type your report below this line ***
> Without 'nosmp' system hangs immediatly. No log is written. Maybe the
> problem is the quite new CPU:
>
> The Laptop has a T3200 processor, all I found out about it is:
>
> The Intel(R) Pentium(R) Dual-Core Mobile Processor T3200 is a dual core
> processor; it is part of the Intel(R) Pentium(R) Dual-Core Mobile
> family.
> CPU speed: 2.00GHz
> L2 Cache Size: 1MB
> Bus Speed: 667MHz
> Processor architecture: 32 bits
>
> The system works fine with 'nosmp', however, only on one CPU. I would
> appreciate to get a solution for using both CPUs.
Sorry for the reply, we're working ourselves through a large backlog.
This should be fixed in current kernels and we won't backport this to
Lenny any more, since our efforts are focused on the upcoming Squeeze
release. Please use a kernel from backports.org for now.
Cheers,
Moritz
--- End Message ---