--- Begin Message ---
- To: Debian Bug Tracking System <submit@bugs.debian.org>
- Subject: linux-image-2.6.30-1-powerpc: can't load Module snd-powermac
- From: Heiner Kurz <hkurz@t-online.de>
- Date: Sun, 21 Jun 2009 15:58:35 +0200
- Message-id: <20090621135835.4464.64891.reportbug@anubis.u8.wan>
Package: linux-image-2.6.30-1-powerpc
Version: 2.6.30-1
Severity: normal
modprobe snd-powermac --> Fatal: ... no Moule snd_powermac found ??
snd-powermac or snd_powermac ??
-- Package-specific info:
** Version:
Linux version 2.6.30-1-powerpc (Debian 2.6.30-1) (waldi@debian.org) (gcc version 4.3.3 (Debian 4.3.3-10) ) #1 Sun Jun 14 12:09:46 CEST 2009
** Command line:
root=/dev/sda12 ro
** Not tainted
** Kernel log:
[ 9.271958] usb 3-1: Product: NetScroll + Mini Traveler
[ 9.281173] usb 3-1: Manufacturer: Genius
[ 9.290515] usb 3-1: configuration #1 chosen from 1 choice
[ 9.302282] scsi0 : SBP-2 IEEE-1394
[ 9.317587] input: Genius NetScroll + Mini Traveler as /devices/pci0001:10/0001:10:1b.1/usb3/3-1/3-1:1.0/input/input7
[ 9.327280] generic-usb 0003:0458:0036.0003: input,hidraw2: USB HID v1.10 Mouse [Genius NetScroll + Mini Traveler] on usb-0001:10:1b.1-1/input0
[ 10.104619] firewire_sbp2: fw1.0: logged in to LUN 0000 (0 retries)
[ 10.120155] scsi 0:0:0:0: Direct-Access Ext Hard Disk PQ: 0 ANSI: 4
[ 10.144740] Driver 'sd' needs updating - please use bus_type methods
[ 10.163017] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors: (500 GB/465 GiB)
[ 10.175666] sd 0:0:0:0: [sda] Write Protect is off
[ 10.185543] sd 0:0:0:0: [sda] Mode Sense: 10 00 00 00
[ 10.187334] sd 0:0:0:0: [sda] Cache data unavailable
[ 10.197157] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 10.214875] sd 0:0:0:0: [sda] Cache data unavailable
[ 10.224640] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 10.234369] sda: [mac] sda1 sda2 sda3 sda4 sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12 sda13 sda14 sda15
[ 10.259399] sd 0:0:0:0: [sda] Attached SCSI disk
[ 10.928454] PM: Starting manual resume from disk
[ 11.132174] kjournald starting. Commit interval 5 seconds
[ 11.141772] EXT3-fs: mounted filesystem with ordered data mode.
[ 12.136881] eth0: Link is up at 1000 Mbps, full-duplex.
[ 12.574272] udev: starting version 141
[ 12.834054] yenta_cardbus 0001:10:13.0: CardBus bridge found [0000:0000]
[ 12.843982] yenta_cardbus 0001:10:13.0: Enabling burst memory read transactions
[ 12.853969] yenta_cardbus 0001:10:13.0: Using CSCINT to route CSC interrupts to PCI
[ 12.863859] yenta_cardbus 0001:10:13.0: Routing CardBus interrupts to PCI
[ 12.873565] yenta_cardbus 0001:10:13.0: TI: mfunc 0x00001002, devctl 0x60
[ 12.932889] cfg80211: Using static regulatory domain info
[ 12.942464] cfg80211: Regulatory domain: EU
[ 12.951836] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 12.961258] (2402000 KHz - 2482000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
[ 12.970631] (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 12.979847] (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 12.988791] (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 12.997453] (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
[ 13.006000] (5490000 KHz - 5710000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
[ 13.014435] cfg80211: Calling CRDA for country: EU
[ 13.128668] yenta_cardbus 0001:10:13.0: ISA IRQ mask 0x0000, PCI irq 53
[ 13.137278] yenta_cardbus 0001:10:13.0: Socket status: 30000087
[ 13.145696] yenta_cardbus 0001:10:13.0: pcmcia: parent PCI bridge I/O window: 0x0 - 0x7fffff
[ 13.154225] yenta_cardbus 0001:10:13.0: pcmcia: parent PCI bridge Memory window: 0xf3000000 - 0xf3ffffff
[ 13.162768] yenta_cardbus 0001:10:13.0: pcmcia: parent PCI bridge Memory window: 0x80000000 - 0xafffffff
[ 13.917398] usb 1-1: USB disconnect, address 2
[ 13.929663] usb 1-1: usbfs: USBDEVFS_CONTROL failed cmd hid2hci rqt 64 rq 0 len 0 ret -62
[ 14.216790] usb 1-1: new full speed USB device using ohci_hcd and address 3
[ 14.412922] b43-phy0: Broadcom 4306 WLAN found (core revision 5)
[ 14.430783] usb 1-1: New USB device found, idVendor=05ac, idProduct=8203
[ 14.438836] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 14.446880] usb 1-1: configuration #1 chosen from 1 choice
[ 15.183688] phy0: Selected rate control algorithm 'minstrel'
[ 15.184537] Broadcom 43xx driver loaded [ Features: PMLR, Firmware-ID: FW13 ]
[ 15.542924] Bluetooth: Core ver 2.15
[ 15.554012] NET: Registered protocol family 31
[ 15.562069] Bluetooth: HCI device and connection manager initialized
[ 15.570069] Bluetooth: HCI socket layer initialized
[ 15.583174] Bluetooth: Generic Bluetooth USB driver ver 0.5
[ 15.591135] usbcore: registered new interface driver btusb
[ 16.352413] Adding 6835928k swap on /dev/sda13. Priority:-1 extents:1 across:6835928k
[ 16.634074] EXT3 FS on sda12, internal journal
[ 17.032613] uhci_hcd: USB Universal Host Controller Interface driver
[ 17.070234] loop: module loaded
[ 17.119869] adt746x: version 1 (supported)
[ 17.127925] adt746x: Thermostat bus: 1, address: 0x2e, limit_adjust: 0, fan_speed: -1
[ 17.135989] sensor 0: CPU/INTREPID BOTTOMSIDE
[ 17.144107] sensor 1: CPU BOTTOMSIDE
[ 17.152250] sensor 2: PWR SUPPLY BOTTOMSIDE
[ 17.349804] adt746x: ADT7460 initializing
[ 17.360646] adt746x: Lowering max temperatures from 73, 73, 73 to 70, 50, 70
[ 18.046264] kjournald starting. Commit interval 5 seconds
[ 18.055378] EXT3 FS on sda14, internal journal
[ 18.064071] EXT3-fs: mounted filesystem with ordered data mode.
[ 20.032641] eth0: Link is up at 1000 Mbps, full-duplex.
[ 20.033748] eth0: Pause is enabled (rxfifo: 10240 off: 7168 on: 5632)
[ 30.588714] eth0: no IPv6 routers present
[ 35.015050] input: Mouseemu virtual keyboard as /devices/virtual/input/input8
[ 35.016523] input: Mouseemu virtual mouse as /devices/virtual/input/input9
[ 36.870489] hda: host max PIO4 wanted PIO0 selected PIO0
[ 37.085033] Bluetooth: L2CAP ver 2.13
[ 37.086134] Bluetooth: L2CAP socket layer initialized
[ 37.186157] Bluetooth: SCO (Voice Link) ver 0.6
[ 37.187273] Bluetooth: SCO socket layer initialized
[ 37.191542] Bluetooth: RFCOMM socket layer initialized
[ 37.192669] Bluetooth: RFCOMM TTY layer initialized
[ 37.193744] Bluetooth: RFCOMM ver 1.11
[ 37.224371] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 37.225500] Bluetooth: BNEP filters: protocol multicast
[ 37.273323] Bridge firewalling registered
[ 37.419594] lp: driver loaded but no devices found
[ 40.030680] radeonfb 0000:00:10.0: Invalid ROM contents
[ 40.030795] radeonfb 0000:00:10.0: Invalid ROM contents
[ 40.100480] [drm] Initialized drm 1.1.0 20060810
[ 40.131382] [drm] Initialized radeon 1.30.0 20080528 for 0000:00:10.0 on minor 0
[ 40.522066] agpgart-uninorth 0000:00:0b.0: putting AGP V2 device into 4x mode
[ 40.522079] radeonfb 0000:00:10.0: putting AGP V2 device into 4x mode
[ 40.852846] [drm] Setting GART location based on new memory map
[ 40.852944] [drm] Loading R300 Microcode
[ 40.852950] platform radeon_cp.0: firmware: requesting radeon/R300_cp.bin
[ 40.895913] [drm] Num pipes: 1
[ 40.895928] [drm] writeback test succeeded in 1 usecs
** Loaded modules:
Module Size Used by
radeon 166728 2
drm 166280 3 radeon
binfmt_misc 12600 1
lp 13412 0
parport 40908 1 lp
bridge 55844 0
stp 6088 1 bridge
bnep 17196 2
sco 14296 2
rfcomm 42352 4
l2cap 25884 16 bnep,rfcomm
uinput 12028 2
therm_adt746x 13416 0
loop 20072 0
uhci_hcd 30272 0
btusb 16072 2
bluetooth 61744 9 bnep,sco,rfcomm,l2cap,btusb
arc4 5168 2
ecb 6452 2
b43 139128 0
snd_aoa_i2sbus 23384 0
rfkill 15216 1 b43
rng_core 7936 1 b43
snd_pcm_oss 45784 0
snd_mixer_oss 21040 1 snd_pcm_oss
snd_pcm 80452 2 snd_aoa_i2sbus,snd_pcm_oss
snd_page_alloc 13200 1 snd_pcm
mac80211 179756 1 b43
snd_seq_midi 10576 0
snd_rawmidi 27140 1 snd_seq_midi
snd_seq_midi_event 10576 1 snd_seq_midi
snd_seq 59032 2 snd_seq_midi,snd_seq_midi_event
evdev 14076 24
snd_timer 25828 2 snd_pcm,snd_seq
snd_seq_device 11044 3 snd_seq_midi,snd_rawmidi,snd_seq
snd 66820 8 snd_aoa_i2sbus,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
soundcore 10324 1 snd
snd_aoa_soundbus 9028 1 snd_aoa_i2sbus
cfg80211 72620 2 b43,mac80211
input_polldev 7836 1 b43
yenta_socket 29248 1
rsrc_nonstatic 13708 1 yenta_socket
ext3 137900 2
jbd 50792 1 ext3
mbcache 11432 1 ext3
sd_mod 37912 4
crc_t10dif 5260 1 sd_mod
firewire_sbp2 18632 3
scsi_mod 157028 2 sd_mod,firewire_sbp2
firewire_ohci 28232 0
ide_cd_mod 32536 0
usbhid 43352 0
sungem 33348 0
sungem_phy 14788 1 sungem
hid 48160 1 usbhid
cdrom 41400 1 ide_cd_mod
firewire_core 50252 2 firewire_sbp2,firewire_ohci
crc_itu_t 5780 1 firewire_core
ssb 51416 1 b43
pcmcia 32336 2 b43,ssb
ehci_hcd 44424 0
pcmcia_core 40896 5 b43,yenta_socket,rsrc_nonstatic,ssb,pcmcia
uninorth_agp 12356 1
agpgart 40976 2 drm,uninorth_agp
i2c_powermac 8320 0
** PCI devices:
0000:00:0b.0 Host bridge [0600]: Apple Computer Inc. UniNorth 2 AGP [106b:0034]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 16, Cache Line Size: 32 bytes
Capabilities: <access denied>
Kernel driver in use: agpgart-uninorth
0000:00:10.0 VGA compatible controller [0300]: ATI Technologies Inc RV350 [Mobility Radeon 9600 M10] [1002:4e50] (prog-if 00 [VGA controller])
Subsystem: ATI Technologies Inc RV350 [Mobility Radeon 9600 M10] [1002:4e50]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 255 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 48
Region 0: Memory at b8000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 0400 [size=256]
Region 2: Memory at b0000000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at b0020000 [size=128K]
Capabilities: <access denied>
Kernel driver in use: radeonfb
0001:10:0b.0 Host bridge [0600]: Apple Computer Inc. UniNorth 2 PCI [106b:0035]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 16, Cache Line Size: 32 bytes
0001:10:12.0 Network controller [0280]: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller [14e4:4320] (rev 03)
Subsystem: Apple Computer Inc. AirPort Extreme [106b:004e]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16
Interrupt: pin A routed to IRQ 52
Region 0: Memory at a0006000 (32-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: b43-pci-bridge
0001:10:13.0 CardBus bridge [0607]: Texas Instruments PCI1510 PC card Cardbus Controller [104c:ac56]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 53
Region 0: Memory at a0004000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=10, secondary=11, subordinate=14, sec-latency=176
Memory window 0: 84000000-87fff000 (prefetchable)
Memory window 1: 88000000-8bfff000
I/O window 0: 00001000-000010ff
I/O window 1: 00001100-000011ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
0001:10:17.0 Class [ff00]: Apple Computer Inc. KeyLargo/Intrepid Mac I/O [106b:003e]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16, Cache Line Size: 32 bytes
Region 0: Memory at 80000000 (32-bit, non-prefetchable) [size=512K]
Kernel driver in use: macio
0001:10:18.0 USB Controller [0c03]: Apple Computer Inc. KeyLargo/Intrepid USB [106b:003f] (prog-if 10 [OHCI])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 27
0001:10:19.0 USB Controller [0c03]: Apple Computer Inc. KeyLargo/Intrepid USB [106b:003f] (prog-if 10 [OHCI])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 28
0001:10:1a.0 USB Controller [0c03]: Apple Computer Inc. KeyLargo/Intrepid USB [106b:003f] (prog-if 10 [OHCI])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (750ns min, 21500ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 29
Region 0: Memory at a0003000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
0001:10:1b.0 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 43) (prog-if 10 [OHCI])
Subsystem: NEC Corporation Hama USB 2.0 CardBus [1033:0035]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (250ns min, 10500ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 63
Region 0: Memory at a0002000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
0001:10:1b.1 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 43) (prog-if 10 [OHCI])
Subsystem: NEC Corporation Hama USB 2.0 CardBus [1033:0035]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (250ns min, 10500ns max), Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 63
Region 0: Memory at a0001000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
0001:10:1b.2 USB Controller [0c03]: NEC Corporation USB 2.0 [1033:00e0] (rev 04) (prog-if 20 [EHCI])
Subsystem: NEC Corporation USB 2.0 [1033:00e0]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (4000ns min, 8500ns max), Cache Line Size: 32 bytes
Interrupt: pin C routed to IRQ 63
Region 0: Memory at a0000000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
0002:24:0b.0 Host bridge [0600]: Apple Computer Inc. UniNorth 2 Internal PCI [106b:0036]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 16, Cache Line Size: 32 bytes
0002:24:0d.0 Class [ff00]: Apple Computer Inc. UniNorth/Intrepid ATA/100 [106b:003b]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+ INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin ? routed to IRQ 39
Region 0: Memory at f5004000 (32-bit, non-prefetchable) [size=16K]
Kernel driver in use: ide-pmac
0002:24:0e.0 FireWire (IEEE 1394) [0c00]: Apple Computer Inc. UniNorth 2 FireWire [106b:0031] (rev 81) (prog-if 10 [OHCI])
Subsystem: Apple Computer Inc. iBook G4 2004 [106b:5811]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (3000ns min, 6000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 40
Region 0: Memory at f5000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
0002:24:0f.0 Ethernet controller [0200]: Apple Computer Inc. UniNorth 2 GMAC (Sun GEM) [106b:0032] (rev 80)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR+ INTx-
Latency: 16 (16000ns min, 16000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 41
Region 0: Memory at f5200000 (32-bit, non-prefetchable) [size=2M]
Expansion ROM at f5100000 [disabled] [size=1M]
Kernel driver in use: gem
-- System Information:
Debian Release: squeeze/sid
APT prefers unstable
APT policy: (500, 'unstable')
Architecture: powerpc (ppc)
Kernel: Linux 2.6.30-1-powerpc
Locale: LANG=de_DE@euro, LC_CTYPE=de_DE@euro (charmap=ISO-8859-15)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.30-1-powerpc depends on:
ii debconf [debconf-2.0] 1.5.26 Debian configuration management sy
ii initramfs-tools [linux-initra 0.93.3 tools for generating an initramfs
ii libc6 2.9-17 GNU C Library: Shared libraries
ii module-init-tools 3.9-2 tools for managing Linux kernel mo
linux-image-2.6.30-1-powerpc recommends no packages.
Versions of packages linux-image-2.6.30-1-powerpc suggests:
ii linux-doc-2.6.30 2.6.30-1 Linux kernel specific documentatio
pn mkvmlinuz <none> (no description available)
-- debconf information:
linux-image-2.6.30-1-powerpc/postinst/old-system-map-link-2.6.30-1-powerpc: true
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.30-1-powerpc/preinst/elilo-initrd-2.6.30-1-powerpc: true
linux-image-2.6.30-1-powerpc/preinst/abort-install-2.6.30-1-powerpc:
linux-image-2.6.30-1-powerpc/prerm/would-invalidate-boot-loader-2.6.30-1-powerpc: true
linux-image-2.6.30-1-powerpc/postinst/old-dir-initrd-link-2.6.30-1-powerpc: true
linux-image-2.6.30-1-powerpc/postinst/old-initrd-link-2.6.30-1-powerpc: true
linux-image-2.6.30-1-powerpc/preinst/bootloader-initrd-2.6.30-1-powerpc: true
linux-image-2.6.30-1-powerpc/postinst/depmod-error-2.6.30-1-powerpc: false
linux-image-2.6.30-1-powerpc/prerm/removing-running-kernel-2.6.30-1-powerpc: true
linux-image-2.6.30-1-powerpc/postinst/bootloader-error-2.6.30-1-powerpc:
linux-image-2.6.30-1-powerpc/preinst/abort-overwrite-2.6.30-1-powerpc:
linux-image-2.6.30-1-powerpc/preinst/failed-to-move-modules-2.6.30-1-powerpc:
linux-image-2.6.30-1-powerpc/preinst/lilo-has-ramdisk:
linux-image-2.6.30-1-powerpc/postinst/create-kimage-link-2.6.30-1-powerpc: true
linux-image-2.6.30-1-powerpc/postinst/kimage-is-a-directory:
linux-image-2.6.30-1-powerpc/postinst/depmod-error-initrd-2.6.30-1-powerpc: false
linux-image-2.6.30-1-powerpc/preinst/overwriting-modules-2.6.30-1-powerpc: true
linux-image-2.6.30-1-powerpc/preinst/initrd-2.6.30-1-powerpc:
linux-image-2.6.30-1-powerpc/postinst/bootloader-test-error-2.6.30-1-powerpc:
linux-image-2.6.30-1-powerpc/preinst/lilo-initrd-2.6.30-1-powerpc: true
--- End Message ---