Bug#566208: linux-image-2.6.26-2-486: e_powersaver causes constant lockups
Package: linux-image-2.6.26-2-486
Version: 2.6.26-19lenny2
Severity: critical
Justification: breaks the whole system
After upgrading linux-image-2.6.26-2-486 from 17lenny1 to 19lenny2, I
started experiencing 100% reproducable system lockups on a VIA C7
system. No errors in the logs, no oops, no BUG, nothing - just a hard
lock. No keyboard LED response and no sysrq functionality worked.
Sometimes the system wouldn't complete the boot process without
freezing. Sometimes it would last three minutes or so before
freezing. I could reproduce the lockup with "cat /dev/zero > file".
Every time, within 10 seconds, the system would freeze.
After a lot of trial, error, and searching, I discovered that the
e_powersaver module was being loaded and the lockups went away if I
unloaded it.
The kernel build help text indicates that the module shouldn't ever be
used, and is highly dangerous:
This adds the CPUFreq driver for VIA C7 processors. However, this
driver does not have any safeguards to prevent operating the CPU out
of spec and is thus considered dangerous. Please use the regular ACPI
cpufreq driver, enabled by CONFIG_X86_ACPI_CPUFREQ.
I have blacklisted this module and suspect that it should be
blacklisted by default. It seems possible that Debian bug #563941 is
related to this issue as well, but there's not enough info in the
report for me to be sure.
Thanks,
Ross
-- Package-specific info:
** Version:
Linux version 2.6.26-2-486 (Debian 2.6.26-19lenny2) (dannf@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 Wed Nov 4 20:19:07 UTC 2009
** Command line:
root=LABEL=root ro
** Not tainted
** Kernel log:
[ 13.058778] udevd version 125 started
[ 13.061147] usb 2-1: new low speed USB device using uhci_hcd and address 2
[ 13.303392] usb 2-1: configuration #1 chosen from 1 choice
[ 13.308441] usb 2-1: New USB device found, idVendor=051d, idProduct=0002
[ 13.308522] usb 2-1: New USB device strings: Mfr=3, Product=1, SerialNumber=2
[ 13.308596] usb 2-1: Product: Back-UPS XS 1300 LCD FW:836.H7 .D USB FW:H7
[ 13.308667] usb 2-1: Manufacturer: American Power Conversion
[ 13.308736] usb 2-1: SerialNumber: 8B0749R09108
[ 17.063851] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 17.111770] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 17.171321] Linux agpgart interface v0.103
[ 17.321713] agpgart: Detected VIA P4M900 chipset
[ 17.324789] agpgart: AGP aperture is 32M @ 0xfc000000
[ 19.291607] Initializing USB Mass Storage driver...
[ 19.400611] scsi4 : SCSI emulation for USB Mass Storage devices
[ 19.401000] scsi5 : SCSI emulation for USB Mass Storage devices
[ 19.401232] usbcore: registered new interface driver usb-storage
[ 19.401305] USB Mass Storage support registered.
[ 19.461227] usb-storage: device found at 4
[ 19.461238] usb-storage: waiting for device to settle before scanning
[ 19.464808] usb-storage: device found at 2
[ 19.464815] usb-storage: waiting for device to settle before scanning
[ 19.832163] input: Power Button (FF) as /class/input/input1
[ 19.863234] ACPI: Power Button (FF) [PWRF]
[ 19.863598] input: Sleep Button (CM) as /class/input/input2
[ 19.888589] ACPI: Sleep Button (CM) [SLPB]
[ 19.888860] input: Power Button (CM) as /class/input/input3
[ 19.921730] ACPI: Power Button (CM) [PWRB]
[ 22.914126] input: PC Speaker as /class/input/input4
[ 23.138478] Error: Driver 'pcspkr' is already registered, aborting...
[ 23.248778] ACPI: PCI Interrupt 0000:80:01.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 23.248968] PCI: Setting latency timer of device 0000:80:01.0 to 64
[ 24.460310] usb-storage: device scan complete
[ 24.461172] scsi 5:0:0:0: Direct-Access Generic Flash Disk 8.07 PQ: 0 ANSI: 2
[ 24.475496] sd 5:0:0:0: [sde] 1978368 512-byte hardware sectors (1013 MB)
[ 24.476243] sd 5:0:0:0: [sde] Write Protect is off
[ 24.476321] sd 5:0:0:0: [sde] Mode Sense: 03 00 00 00
[ 24.476330] sd 5:0:0:0: [sde] Assuming drive cache: write through
[ 24.479494] sd 5:0:0:0: [sde] 1978368 512-byte hardware sectors (1013 MB)
[ 24.480239] sd 5:0:0:0: [sde] Write Protect is off
[ 24.480318] sd 5:0:0:0: [sde] Mode Sense: 03 00 00 00
[ 24.480326] sd 5:0:0:0: [sde] Assuming drive cache: write through
[ 24.480414] sde:<7>usb-storage: device scan complete
[ 24.522804] scsi 4:0:0:0: Direct-Access Seagate FreeAgent 0132 PQ: 0 ANSI: 4
[ 24.706237] sde1
[ 24.706650] sd 5:0:0:0: [sde] Attached SCSI removable disk
[ 24.710798] sd 4:0:0:0: [sdf] 3907029168 512-byte hardware sectors (2000399 MB)
[ 24.711555] sd 4:0:0:0: [sdf] Write Protect is off
[ 24.711646] sd 4:0:0:0: [sdf] Mode Sense: 2d 08 00 00
[ 24.711654] sd 4:0:0:0: [sdf] Assuming drive cache: write through
[ 24.712930] sd 4:0:0:0: [sdf] 3907029168 512-byte hardware sectors (2000399 MB)
[ 24.714540] sd 4:0:0:0: [sdf] Write Protect is off
[ 24.714628] sd 4:0:0:0: [sdf] Mode Sense: 2d 08 00 00
[ 24.714637] sd 4:0:0:0: [sdf] Assuming drive cache: write through
[ 24.714716] sdf: sdf1
[ 24.715723] sd 4:0:0:0: [sdf] Attached SCSI disk
[ 25.096135] usbcore: registered new interface driver hiddev
[ 26.244006] hiddev96hidraw0: USB HID v1.10 Device [American Power Conversion Back-UPS XS 1300 LCD FW:836.H7 .D USB FW:H7 ] on usb-0000:00:10.1-1
[ 26.244006] usbcore: registered new interface driver usbhid
[ 26.244006] usbhid: v2.6:USB HID core driver
[ 27.268160] loop: module loaded
[ 27.367886] VIA RNG detected
[ 27.723889] device-mapper: uevent: version 1.0.3
[ 27.726303] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
[ 30.372571] kjournald starting. Commit interval 5 seconds
[ 30.464801] EXT3 FS on md0, internal journal
[ 30.464801] EXT3-fs: mounted filesystem with ordered data mode.
[ 39.993660] Velocity is AUTO mode
[ 40.663915] NET: Registered protocol family 10
[ 40.665220] lo: Disabled Privacy Extensions
[ 40.666674] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 42.173092] eps: Detected VIA Model A C7
[ 42.173106] eps: Current voltage = 1004mV
[ 42.173112] eps: Current multiplier = 10
[ 42.173119] eps: Highest voltage = 1004mV
[ 42.173125] eps: Highest multiplier = 10
[ 42.173131] eps: Lowest voltage = 956mV
[ 42.173136] eps: Lowest multiplier = 8
[ 42.358718] eth0: Link auto-negotiation speed 1000M bps full duplex
[ 42.360315] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 43.796005] Marking TSC unstable due to: cpufreq changes.
[ 44.340029] Clocksource tsc unstable (delta = -100020487 ns)
[ 47.259830] hda: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
[ 47.260022] hda: task_no_data_intr: error=0x04 { DriveStatusError }
[ 47.260022] ide: failed opcode was: 0xb0
[ 47.803018] RPC: Registered udp transport module.
[ 47.803103] RPC: Registered tcp transport module.
[ 47.859772] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 47.942762] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 47.942884] NFSD: starting 90-second grace period
[ 49.728398] warning: `proftpd' uses 32-bit capabilities (legacy support in use)
[ 53.156020] eth0: no IPv6 routers present
[ 75.407677] usb 4-5: USB disconnect, address 4
[ 321.022982] eps: Detected VIA Model A C7
[ 321.023155] eps: Current voltage = 1004mV
[ 321.023219] eps: Current multiplier = 10
[ 321.023283] eps: Highest voltage = 1004mV
[ 321.023347] eps: Highest multiplier = 10
[ 321.023410] eps: Lowest voltage = 956mV
[ 321.023474] eps: Lowest multiplier = 8
** Loaded modules:
Module Size Used by
nfsd 185456 13
lockd 54152 1 nfsd
nfs_acl 2816 1 nfsd
auth_rpcgss 33184 1 nfsd
sunrpc 157596 11 nfsd,lockd,nfs_acl,auth_rpcgss
exportfs 3712 1 nfsd
cpufreq_powersave 1792 0
cpufreq_userspace 2968 0
cpufreq_stats 3076 0
cpufreq_ondemand 6036 0
freq_table 4100 2 cpufreq_stats,cpufreq_ondemand
cpufreq_conservative 5664 0
ipv6 225172 32
ext3 103688 1
jbd 35092 1 ext3
dm_snapshot 14240 0
dm_mirror 14720 0
dm_log 8192 1 dm_mirror
dm_mod 45384 5 dm_snapshot,dm_mirror,dm_log
via_rng 2048 0
rng_core 3972 2 via_rng
loop 12428 0
usbhid 35712 1
hid 32128 1 usbhid
ff_memless 4232 1 usbhid
snd_hda_intel 325400 0
i2c_viapro 6804 0
i2c_core 19728 1 i2c_viapro
snd_pcm 60680 1 snd_hda_intel
snd_timer 17668 1 snd_pcm
snd 45092 3 snd_hda_intel,snd_pcm,snd_timer
soundcore 6112 1 snd
snd_page_alloc 7816 2 snd_hda_intel,snd_pcm
pcspkr 2304 0
button 6032 0
usb_storage 76864 1
via_agp 7680 1
agpgart 28336 1 via_agp
shpchp 25496 0
pci_hotplug 23204 1 shpchp
evdev 7808 0
ext2 52744 1
mbcache 6656 2 ext3,ext2
raid456 115216 1
md_mod 65940 2 raid456
async_xor 3456 1 raid456
async_memcpy 2176 1 raid456
async_tx 5960 3 raid456,async_xor,async_memcpy
xor 14728 2 raid456,async_xor
ide_disk 10496 2
ide_pci_generic 3844 0 [permanent]
sd_mod 22032 10
via82cxxx 6916 0 [permanent]
ide_core 95144 3 ide_disk,ide_pci_generic,via82cxxx
via_rhine 18184 0
mii 4864 1 via_rhine
uhci_hcd 18448 0
ehci_hcd 28300 0
ahci 23564 8
ata_generic 4612 0
libata 141216 2 ahci,ata_generic
usbcore 117616 6 usbhid,usb_storage,uhci_hcd,ehci_hcd
scsi_mod 130060 3 usb_storage,sd_mod,libata
dock 8076 1 libata
via_velocity 25988 0
crc_ccitt 2048 1 via_velocity
thermal 15132 0
processor 28080 1 thermal
fan 4100 0
thermal_sys 10784 3 thermal,processor,fan
** PCI devices:
00:00.0 Host bridge [0600]: VIA Technologies, Inc. CN896/VN896/P4M900 Host Bridge [1106:0364]
Subsystem: VIA Technologies, Inc. CN896/VN896/P4M900 Host Bridge [1106:0364]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 8
Region 0: Memory at <ignored> (32-bit, prefetchable)
Capabilities: <access denied>
Kernel driver in use: agpgart-via
Kernel modules: via-agp
00:00.1 Host bridge [0600]: VIA Technologies, Inc. CN896/VN896/P4M900 Host Bridge [1106:1364]
Subsystem: VIA Technologies, Inc. CN896/VN896/P4M900 Host Bridge [1106:1364]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:00.2 Host bridge [0600]: VIA Technologies, Inc. CN896/VN896/P4M900 Host Bridge [1106:2364]
Subsystem: VIA Technologies, Inc. CN896/VN896/P4M900 Host Bridge [1106:2364]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:00.3 Host bridge [0600]: VIA Technologies, Inc. CN896/VN896/P4M900 Host Bridge [1106:3364]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:00.4 Host bridge [0600]: VIA Technologies, Inc. CN896/VN896/P4M900 Host Bridge [1106:4364]
Subsystem: VIA Technologies, Inc. CN896/VN896/P4M900 Host Bridge [1106:4364]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:00.5 PIC [0800]: VIA Technologies, Inc. CN896/VN896/P4M900 I/O APIC Interrupt Controller [1106:5364] (prog-if 20 [IO(X)-APIC])
Subsystem: VIA Technologies, Inc. CN896/VN896/P4M900 I/O APIC Interrupt Controller [1106:5364]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:00.6 Host bridge [0600]: VIA Technologies, Inc. CN896/VN896/P4M900 Security Device [1106:6364]
Subsystem: VIA Technologies, Inc. CN896/VN896/P4M900 Security Device [1106:6364]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:00.7 Host bridge [0600]: VIA Technologies, Inc. CN896/VN896/P4M900 Host Bridge [1106:7364]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:01.0 PCI bridge [0604]: VIA Technologies, Inc. VT8237/VX700 PCI Bridge [1106:b198] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: fb000000-fe9fffff
Prefetchable memory behind bridge: f4000000-f7ffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel modules: shpchp
00:02.0 PCI bridge [0604]: VIA Technologies, Inc. CN896/VN896/P4M900 PCI to PCI Bridge Controller [1106:a364] (rev 80) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:03.0 PCI bridge [0604]: VIA Technologies, Inc. CN896/VN896/P4M900 PCI to PCI Bridge Controller [1106:c364] (rev 80) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR+ <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fea00000-feafffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR+ <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:0f.0 SATA controller [0106]: VIA Technologies, Inc. SATA RAID Controller [1106:6287] (rev 20) (prog-if 01 [AHCI 1.0])
Subsystem: VIA Technologies, Inc. SATA RAID Controller [1106:6287]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin B routed to IRQ 219
Region 0: I/O ports at dc00 [size=8]
Region 1: I/O ports at d880 [size=4]
Region 2: I/O ports at d800 [size=8]
Region 3: I/O ports at d480 [size=4]
Region 4: I/O ports at d400 [size=16]
Region 5: Memory at fafffc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ahci
Kernel modules: ahci
00:0f.1 IDE interface [0101]: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE [1106:0571] (rev 07) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE [1106:0571]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1]
Region 4: I/O ports at fc00 [size=16]
Capabilities: <access denied>
Kernel driver in use: VIA_IDE
Kernel modules: via82cxxx
00:10.0 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 91) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at cc00 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:10.1 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 91) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin C routed to IRQ 22
Region 4: I/O ports at d000 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:10.2 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 91) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at d080 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:10.4 USB Controller [0c03]: VIA Technologies, Inc. USB 2.0 [1106:3104] (rev 90) (prog-if 20 [EHCI])
Subsystem: VIA Technologies, Inc. USB 2.0 [1106:3104]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin C routed to IRQ 22
Region 0: Memory at fafff800 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:11.0 ISA bridge [0601]: VIA Technologies, Inc. VT8251 PCI to ISA Bridge [1106:3287]
Subsystem: VIA Technologies, Inc. VT8251 PCI to ISA Bridge [1106:3287]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
Kernel modules: i2c-viapro
00:11.7 Host bridge [0600]: VIA Technologies, Inc. VT8251 Ultra VLINK Controller [1106:287e]
Subsystem: VIA Technologies, Inc. VT8251 Ultra VLINK Controller [1106:287e]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 128
Capabilities: <access denied>
00:12.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6102 [Rhine-II] [1106:3065] (rev 7c)
Subsystem: VIA Technologies, Inc. VT6102 [Rhine II] Embeded Ethernet Controller on VT8235 [1106:0102]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (750ns min, 2000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 23
Region 0: I/O ports at c800 [size=256]
Region 1: Memory at fafff400 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: via-rhine
Kernel modules: via-rhine
00:13.0 Host bridge [0600]: VIA Technologies, Inc. VT8251 Host Bridge [1106:287b]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
00:14.0 Network controller [0280]: Intel Corporation PRO/Wireless 2915ABG [Calexico2] Network Connection [8086:4223] (rev 05)
Subsystem: Hewlett-Packard Company Device [103c:1354]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (750ns min, 6000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 5
Region 0: Memory at faffe000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel modules: ipw2200
01:00.0 VGA compatible controller [0300]: VIA Technologies, Inc. CN896/VN896/P4M900 [Chrome 9 HC] [1106:3371] (rev 01) (prog-if 00 [VGA controller])
Subsystem: Device [0908:1975]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (500ns min)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f4000000 (32-bit, prefetchable) [size=64M]
Region 1: Memory at fb000000 (32-bit, non-prefetchable) [size=16M]
Expansion ROM at fe9f0000 [disabled] [size=64K]
Capabilities: <access denied>
03:00.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6120/VT6121/VT6122 Gigabit Ethernet Adapter [1106:3119] (rev 82)
Subsystem: VIA Technologies, Inc. Device [1106:0110]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR+ <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 28
Region 0: I/O ports at e800 [size=256]
Region 1: Memory at feaffc00 (64-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: via-velocity
Kernel modules: via-velocity
80:00.0 PCI bridge [0604]: VIA Technologies, Inc. VT8251 PCIE Root Port [1106:287c] (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=80, secondary=82, subordinate=82, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
80:00.1 PCI bridge [0604]: VIA Technologies, Inc. VT8251 PCIE Root Port [1106:287d] (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=80, secondary=81, subordinate=81, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
80:01.0 Audio device [0403]: VIA Technologies, Inc. VT1708/A [Azalia HDAC] (VIA High Definition Audio Controller) [1106:3288]
Subsystem: VIA Technologies, Inc. VT1708/A [Azalia HDAC] (VIA High Definition Audio Controller) [1106:3288]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at febfc000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
-- System Information:
Debian Release: 5.0.3
APT prefers stable
APT policy: (500, 'stable')
Architecture: i386 (i686)
Kernel: Linux 2.6.26-2-486
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8) (ignored: LC_ALL set to en_US.UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.26-2-486 depends on:
ii debconf [debconf-2.0] 1.5.24 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92o tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
linux-image-2.6.26-2-486 recommends no packages.
Versions of packages linux-image-2.6.26-2-486 suggests:
ii grub 0.97-47lenny2 GRand Unified Bootloader (Legacy v
pn linux-doc-2.6.26 <none> (no description available)
-- debconf information:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.26-2-486/postinst/depmod-error-2.6.26-2-486: false
linux-image-2.6.26-2-486/preinst/initrd-2.6.26-2-486:
linux-image-2.6.26-2-486/preinst/abort-install-2.6.26-2-486:
linux-image-2.6.26-2-486/preinst/lilo-has-ramdisk:
linux-image-2.6.26-2-486/preinst/lilo-initrd-2.6.26-2-486: true
linux-image-2.6.26-2-486/postinst/create-kimage-link-2.6.26-2-486: true
linux-image-2.6.26-2-486/preinst/elilo-initrd-2.6.26-2-486: true
linux-image-2.6.26-2-486/postinst/bootloader-error-2.6.26-2-486:
linux-image-2.6.26-2-486/preinst/overwriting-modules-2.6.26-2-486: true
linux-image-2.6.26-2-486/postinst/old-system-map-link-2.6.26-2-486: true
linux-image-2.6.26-2-486/prerm/removing-running-kernel-2.6.26-2-486: true
linux-image-2.6.26-2-486/postinst/bootloader-test-error-2.6.26-2-486:
linux-image-2.6.26-2-486/prerm/would-invalidate-boot-loader-2.6.26-2-486: true
linux-image-2.6.26-2-486/preinst/failed-to-move-modules-2.6.26-2-486:
linux-image-2.6.26-2-486/preinst/bootloader-initrd-2.6.26-2-486: true
linux-image-2.6.26-2-486/preinst/abort-overwrite-2.6.26-2-486:
linux-image-2.6.26-2-486/postinst/old-initrd-link-2.6.26-2-486: true
linux-image-2.6.26-2-486/postinst/old-dir-initrd-link-2.6.26-2-486: true
linux-image-2.6.26-2-486/postinst/kimage-is-a-directory:
linux-image-2.6.26-2-486/postinst/depmod-error-initrd-2.6.26-2-486: false
Reply to: