[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Bug#563702: linux-image-2.6.26-2-openvz-686: partition size truncate randomly (mdadm-raid1/lvm2)



Package: linux-image-2.6.26-2-openvz-686
Version: 2.6.26-19lenny2
Severity: critical
Justification: causes serious data loss

[hope my translation was good]

sda1 boot scsi (sdb1 if sda fail) is 		/  			1.9Go
md0 [sda3/sdc3] : raid1 linux (mdadm) & lvm 	/usr, /var		9Go
md1 [sdd1/sde1] : raid1               & lvm	/var/www, /vz, ...	250Go

lvm on md1
/var/www 20Go in reality, but :

# df -h | grep www
/dev/mapper/satavol1-lvm--www
                      1,9G  1,2G  626M  65% /mnt/satavol1/lvm-www

It's critical, there's nothing in syslog to explain, and some directory in /mnt/satavol1/lvm-www
aren't accessible until umount/mount !!
# umount /mnt/satavol1/lvm-www
umount: /dev/mapper/satavol1-lvm--www: not mounted
umount: /dev/mapper/satavol1-lvm--www: not mounted
#  mount /mnt/satavol1/lvm-www
# df -h | grep www
/dev/mapper/satavol1-lvm--www
                       20G  8,7G   12G  44% /mnt/satavol1/lvm-www






since June 2009, df -h report 4 times 1.9G for my lv partition (note that 1.9 is the size of my sda1 
partition instead more (40Go for example)

-- Package-specific info:
** Version:
Linux version 2.6.26-2-openvz-686 (Debian 2.6.26-19lenny2) (dannf@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 SMP Wed Nov 4 22:06:32 UTC 2009

** Command line:
root=/dev/sda1 ro quiet vga=773

** Not tainted

** Kernel log:
[   27.508319] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   27.557229] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   27.753647] Linux agpgart interface v0.103
[   27.789506] parport_pc: VIA 686A/8231 detected
[   27.789519] parport_pc: probing current configuration
[   27.789545] parport_pc: Current parallel port base: 0x0
[   27.789555] parport_pc: VIA parallel port disabled in BIOS
[   27.810101] agpgart: Detected VIA Twister-K/KT133x/KM133 chipset
[   27.816692] agpgart: AGP aperture is 64M @ 0xe0000000
[   28.821295] input: Power Button (FF) as /class/input/input1
[   28.855381] ACPI: Power Button (FF) [PWRF]
[   28.855555] input: Power Button (CM) as /class/input/input2
[   28.880288] ACPI: Power Button (CM) [PWRB]
[   28.880470] input: Sleep Button (CM) as /class/input/input3
[   28.915944] ACPI: Sleep Button (CM) [SLPB]
[   29.093211] input: PC Speaker as /class/input/input4
[   29.284272] ACPI: PCI Interrupt 0000:00:07.5[C] -> Link [LNKD] -> GSI 15 (level, low) -> IRQ 15
[   29.284439] PCI: Setting latency timer of device 0000:00:07.5 to 64
[   29.889735] input: ImPS/2 Generic Wheel Mouse as /class/input/input5
[   31.905295] Adding 489972k swap on /dev/sda2.  Priority:-1 extents:1 across:489972k
[   31.929984] Adding 489972k swap on /dev/sdb2.  Priority:-2 extents:1 across:489972k
[   32.089661] EXT3 FS on sda1, internal journal
[   32.720016] loop: module loaded
[   32.845080] md: faulty personality registered for level -5
[   33.036467] md: bind<sdc3>
[   33.138892] raid1: raid set md1 active with 1 out of 2 mirrors
[   56.544042] ReiserFS: dm-10: found reiserfs format "3.6" with standard journal
[   56.544042] ReiserFS: dm-10: using ordered data mode
[   56.544042] ReiserFS: dm-10: journal params: device dm-10, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[   56.562380] ReiserFS: dm-10: checking transaction log (dm-10)
[   56.584048] ReiserFS: dm-10: Using r5 hash to sort names
[   56.584048] kjournald starting.  Commit interval 5 seconds
[   56.685624] EXT3 FS on sdb1, internal journal
[   56.685637] EXT3-fs: mounted filesystem with ordered data mode.
[   56.709934] ReiserFS: dm-9: found reiserfs format "3.6" with standard journal
[   56.709981] ReiserFS: dm-9: using ordered data mode
[   56.714787] ReiserFS: dm-9: journal params: device dm-9, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[   56.719487] ReiserFS: dm-9: checking transaction log (dm-9)
[   56.760840] ReiserFS: dm-9: Using r5 hash to sort names
[   56.808483] ReiserFS: dm-8: found reiserfs format "3.6" with standard journal
[   56.808483] ReiserFS: dm-8: using ordered data mode
[   56.818488] ReiserFS: dm-8: journal params: device dm-8, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[   56.823131] ReiserFS: dm-8: checking transaction log (dm-8)
[   56.853309] ReiserFS: dm-8: Using r5 hash to sort names
[   56.869739] ReiserFS: dm-6: found reiserfs format "3.6" with standard journal
[   56.869739] ReiserFS: dm-6: using ordered data mode
[   56.872028] ReiserFS: dm-6: journal params: device dm-6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[   56.885369] ReiserFS: dm-6: checking transaction log (dm-6)
[   56.952017] ReiserFS: dm-6: Using r5 hash to sort names
[   56.952017] ReiserFS: dm-7: found reiserfs format "3.6" with standard journal
[   56.952017] ReiserFS: dm-7: using ordered data mode
[   56.952017] ReiserFS: dm-7: journal params: device dm-7, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[   57.035230] ReiserFS: dm-7: checking transaction log (dm-7)
[   57.065802] ReiserFS: dm-7: Using r5 hash to sort names
[   57.088033] ReiserFS: dm-5: found reiserfs format "3.6" with standard journal
[   57.088033] ReiserFS: dm-5: using ordered data mode
[   57.088033] ReiserFS: dm-5: journal params: device dm-5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[   57.106075] ReiserFS: dm-5: checking transaction log (dm-5)
[   57.145513] ReiserFS: dm-5: Using r5 hash to sort names
[   57.160369] ReiserFS: dm-2: found reiserfs format "3.6" with standard journal
[   57.160422] ReiserFS: dm-2: using ordered data mode
[   57.160756] ReiserFS: dm-2: journal params: device dm-2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[   57.165381] ReiserFS: dm-2: checking transaction log (dm-2)
[   57.165984] ReiserFS: dm-2: Using r5 hash to sort names
[   58.580292] e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
[   62.637352] NET: Registered protocol family 10
[   68.412701] ip_tables: (C) 2000-2006 Netfilter Core Team
[   69.777629] tun: Universal TUN/TAP device driver, 1.6
[   69.777646] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   70.773675] warning: `vzctl' uses 32-bit capabilities (legacy support in use)
[   70.781236] CT: 101: started
[   72.906478] CT: 202: started
[   72.912075] eth0: no IPv6 routers present
[   75.309838] CT: 203: started
[   78.187972] CT: 204: started
[   82.007536] CT: 205: started
[   83.220100] veth101.0: no IPv6 routers present
[   86.844284] CT: 206: started
[  950.506385] RPC: Registered udp transport module.
[  950.506404] RPC: Registered tcp transport module.
[  950.628155] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 1014.631993] CT: 202: stopped
[ 1027.207757] CT: 202: started
[ 3646.764834] CT: 202: stopped
[ 3733.954352] ReiserFS: dm-5: found reiserfs format "3.6" with standard journal
[ 3733.954352] ReiserFS: dm-5: using ordered data mode
[ 3733.961435] ReiserFS: dm-5: journal params: device dm-5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 3733.966057] ReiserFS: dm-5: checking transaction log (dm-5)
[ 3734.044018] ReiserFS: dm-5: Using r5 hash to sort names
[ 3742.742649] ReiserFS: dm-6: found reiserfs format "3.6" with standard journal
[ 3742.742649] ReiserFS: dm-6: using ordered data mode
[ 3742.753589] ReiserFS: dm-6: journal params: device dm-6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 3742.758288] ReiserFS: dm-6: checking transaction log (dm-6)
[ 3742.804022] ReiserFS: dm-6: Using r5 hash to sort names
[ 3762.396698] CT: 202: started
[ 3824.348628] CT: 202: stopped
[ 3870.124075] CT: 202: started
[ 4106.977823] CT: 202: stopped
[ 4107.512128] CT: 202: started
[27764.999886] CT: 202: started

** Loaded modules:
Module                  Size  Used by
nfsd                  188752  0 
lockd                  56456  1 nfsd
nfs_acl                 3680  1 nfsd
auth_rpcgss            34752  1 nfsd
sunrpc                166880  6 nfsd,lockd,nfs_acl,auth_rpcgss
exportfs                4832  1 nfsd
vzethdev                9184  0 
vznetdev               14564  10 
simfs                   4756  5 
vzrst                 116532  0 
vzcpt                  97892  0 
tun                    10148  2 vzrst,vzcpt
vzdquota               32796  5 [permanent]
vzmon                  23176  11 vzethdev,vznetdev,vzrst,vzcpt
vzdev                   3624  4 vzethdev,vznetdev,vzdquota,vzmon
xt_tcpudp               3584  0 
xt_length               2528  0 
ipt_ttl                 2368  0 
xt_tcpmss               2752  0 
xt_TCPMSS               4448  0 
iptable_mangle          4640  0 
iptable_filter          4288  0 
xt_multiport            3584  0 
xt_limit                2948  0 
xt_dscp                 3136  0 
ipt_REJECT              3552  0 
ip_tables              11056  2 iptable_mangle,iptable_filter
x_tables               14404  10 xt_tcpudp,xt_length,ipt_ttl,xt_tcpmss,xt_TCPMSS,xt_multiport,xt_limit,xt_dscp,ipt_REJECT,ip_tables
ipv6                  242240  73 vzrst,vzcpt,vzmon
reiserfs              191232  5 
faulty                  4096  0 
loop                   13548  0 
snd_via82xx            21464  0 
gameport               11500  1 snd_via82xx
psmouse                33104  0 
snd_ac97_codec         89220  1 snd_via82xx
ac97_bus                2496  1 snd_ac97_codec
pcspkr                  3200  0 
serio_raw               5508  0 
snd_pcm                63492  2 snd_via82xx,snd_ac97_codec
snd_timer              18568  1 snd_pcm
snd_page_alloc          8648  2 snd_via82xx,snd_pcm
snd_mpu401_uart         7168  1 snd_via82xx
button                  6864  0 
snd_rawmidi            19264  1 snd_mpu401_uart
snd_seq_device          7148  1 snd_rawmidi
snd                    46436  7 snd_via82xx,snd_ac97_codec,snd_pcm,snd_timer,snd_mpu401_uart,snd_rawmidi,snd_seq_device
soundcore               7136  1 snd
via686a                12748  0 
i2c_viapro              7604  0 
i2c_core               20596  1 i2c_viapro
via_agp                 8512  1 
parport_pc             23396  0 
parport                31756  1 parport_pc
agpgart                29576  1 via_agp
shpchp                 26360  0 
pci_hotplug            24260  1 shpchp
evdev                   8736  0 
ext3                  106120  2 
jbd                    40276  1 ext3
mbcache                 7876  1 ext3
dm_mirror              15904  0 
dm_log                  9220  1 dm_mirror
dm_snapshot            15108  0 
dm_mod                 47016  20 dm_mirror,dm_log,dm_snapshot
raid1                  18688  2 
md_mod                 67900  4 faulty,raid1
sd_mod                 22968  10 
ata_generic             5444  0 
sata_promise           10596  2 
aic7xxx               118808  6 
scsi_transport_spi     20608  1 aic7xxx
libata                141376  2 ata_generic,sata_promise
e100                   29900  0 
mii                     5664  1 e100
dock                    9072  1 libata
scsi_mod              130444  4 sd_mod,aic7xxx,scsi_transport_spi,libata
uhci_hcd               19504  0 
usbcore               119280  2 uhci_hcd
via82cxxx               7716  0 [permanent]
ide_pci_generic         4676  0 [permanent]
ide_core               97000  2 via82cxxx,ide_pci_generic
thermal                15996  0 
processor              33568  1 thermal
fan                     4964  0 
thermal_sys            11624  3 thermal,processor,fan

** PCI devices:
00:00.0 Host bridge [0600]: VIA Technologies, Inc. VT8363/8365 [KT133/KM133] [1106:0305] (rev 03)
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
	Latency: 8
	Region 0: Memory at e0000000 (32-bit, prefetchable) [size=64M]
	Capabilities: [a0] AGP version 2.0
		Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
		Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
	Capabilities: [c0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: agpgart-via
	Kernel modules: via-agp

00:01.0 PCI bridge [0604]: VIA Technologies, Inc. VT8363/8365 [KT133/KM133 AGP] [1106:8305] (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
	Latency: 0
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	Memory behind bridge: e4000000-e5ffffff
	Prefetchable memory behind bridge: d0000000-dfffffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [80] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Kernel modules: shpchp

00:07.0 ISA bridge [0601]: VIA Technologies, Inc. VT82C686 [Apollo Super South] [1106:0686] (rev 40)
	Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge [1106:0000]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Capabilities: [c0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: parport_pc
	Kernel modules: parport_pc

00:07.1 IDE interface [0101]: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE [1106:0571] (rev 06) (prog-if 8a [Master SecP PriP])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32
	Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
	Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
	Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
	Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
	Region 4: I/O ports at c000 [size=16]
	Capabilities: [c0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: VIA_IDE
	Kernel modules: via82cxxx

00:07.2 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 16) (prog-if 00 [UHCI])
	Subsystem: First International Computer, Inc. VA-502 Mainboard [0925:1234]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32, Cache Line Size: 32 bytes
	Interrupt: pin D routed to IRQ 7
	Region 4: I/O ports at c400 [size=32]
	Capabilities: [80] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: uhci_hcd
	Kernel modules: uhci-hcd

00:07.3 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 16) (prog-if 00 [UHCI])
	Subsystem: First International Computer, Inc. VA-502 Mainboard [0925:1234]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32, Cache Line Size: 32 bytes
	Interrupt: pin D routed to IRQ 7
	Region 4: I/O ports at c800 [size=32]
	Capabilities: [80] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: uhci_hcd
	Kernel modules: uhci-hcd

00:07.4 Host bridge [0600]: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] [1106:3057] (rev 40)
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin ? routed to IRQ 3
	Capabilities: [68] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Kernel modules: via686a, i2c-viapro

00:07.5 Multimedia audio controller [0401]: VIA Technologies, Inc. VT82C686 AC97 Audio Controller [1106:3058] (rev 50)
	Subsystem: Micro-Star International Co., Ltd. MS-6330 Onboard Audio [1462:3300]
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin C routed to IRQ 15
	Region 0: I/O ports at cc00 [size=256]
	Region 1: I/O ports at d000 [size=4]
	Region 2: I/O ports at d400 [size=4]
	Capabilities: [c0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: VIA 82xx Audio
	Kernel modules: snd-via82xx

00:09.0 SCSI storage controller [0100]: Adaptec AIC-7892A U160/m [9005:0080] (rev 02)
	Subsystem: Adaptec 29160N Ultra160 SCSI Controller [9005:62a0]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32 (10000ns min, 6250ns max), Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 11
	BIST result: 00
	Region 0: I/O ports at d800 [disabled] [size=256]
	Region 1: Memory at e7120000 (64-bit, non-prefetchable) [size=4K]
	[virtual] Expansion ROM at 50000000 [disabled] [size=128K]
	Capabilities: [dc] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: aic7xxx
	Kernel modules: aic7xxx

00:0c.0 Mass storage controller [0180]: Promise Technology, Inc. PDC20375 (SATA150 TX2plus) [105a:3375] (rev 02)
	Subsystem: Promise Technology, Inc. PDC20375 (SATA150 TX2plus) [105a:3375]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 96 (1000ns min, 4500ns max), Cache Line Size: 576 bytes
	Interrupt: pin A routed to IRQ 10
	Region 0: I/O ports at dc00 [size=64]
	Region 1: I/O ports at e000 [size=16]
	Region 2: I/O ports at e400 [size=128]
	Region 3: Memory at e7122000 (32-bit, non-prefetchable) [size=4K]
	Region 4: Memory at e7100000 (32-bit, non-prefetchable) [size=128K]
	[virtual] Expansion ROM at 50020000 [disabled] [size=16K]
	Capabilities: [60] Power Management version 2
		Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: sata_promise
	Kernel modules: sata_promise

00:0e.0 Ethernet controller [0200]: Intel Corporation 82557/8/9/0/1 Ethernet Pro 100 [8086:1229] (rev 08)
	Subsystem: Hewlett-Packard Company NetServer 10/100TX [103c:10cb]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32 (2000ns min, 14000ns max), Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 15
	Region 0: Memory at e7121000 (32-bit, non-prefetchable) [size=4K]
	Region 1: I/O ports at e800 [size=64]
	Region 2: Memory at e7000000 (32-bit, non-prefetchable) [size=1M]
	Capabilities: [dc] Power Management version 2
		Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=2 PME-
	Kernel driver in use: e100
	Kernel modules: e100, eepro100

01:00.0 VGA compatible controller [0300]: nVidia Corporation NV17 [GeForce4 MX 440] [10de:0171] (rev a3) (prog-if 00 [VGA controller])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32 (1250ns min, 250ns max)
	Interrupt: pin A routed to IRQ 7
	Region 0: Memory at e4000000 (32-bit, non-prefetchable) [size=16M]
	Region 1: Memory at d0000000 (32-bit, prefetchable) [size=128M]
	Region 2: Memory at d8000000 (32-bit, prefetchable) [size=512K]
	[virtual] Expansion ROM at d8080000 [disabled] [size=128K]
	Capabilities: [60] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [44] AGP version 2.0
		Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
		Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
	Kernel modules: nvidiafb



-- System Information:
Debian Release: 5.0.3
  APT prefers stable
  APT policy: (500, 'stable')
Architecture: i386 (i686)

Kernel: Linux 2.6.26-2-openvz-686 (SMP w/1 CPU core)
Locale: LANG=fr_FR.UTF-8, LC_CTYPE=fr_FR.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash

Versions of packages linux-image-2.6.26-2-openvz-686 depends on:
ii  debconf [debconf-2.0]         1.5.24     Debian configuration management sy
ii  initramfs-tools [linux-initra 0.92o      tools for generating an initramfs
ii  module-init-tools             3.4-1      tools for managing Linux kernel mo
ii  vzctl                         3.0.22-14  server virtualization solution - c

Versions of packages linux-image-2.6.26-2-openvz-686 recommends:
ii  libc6-i686                    2.7-18     GNU C Library: Shared libraries [i

Versions of packages linux-image-2.6.26-2-openvz-686 suggests:
ii  grub                       0.97-47lenny2 GRand Unified Bootloader (Legacy v
pn  linux-doc-2.6.26           <none>        (no description available)

-- debconf information:
  shared/kernel-image/really-run-bootloader: true
  linux-image-2.6.26-2-openvz-686/preinst/lilo-has-ramdisk:
  linux-image-2.6.26-2-openvz-686/preinst/overwriting-modules-2.6.26-2-openvz-686: true
  linux-image-2.6.26-2-openvz-686/preinst/abort-overwrite-2.6.26-2-openvz-686:
  linux-image-2.6.26-2-openvz-686/preinst/failed-to-move-modules-2.6.26-2-openvz-686:
  linux-image-2.6.26-2-openvz-686/preinst/initrd-2.6.26-2-openvz-686:
  linux-image-2.6.26-2-openvz-686/prerm/removing-running-kernel-2.6.26-2-openvz-686: true
  linux-image-2.6.26-2-openvz-686/postinst/bootloader-test-error-2.6.26-2-openvz-686:
  linux-image-2.6.26-2-openvz-686/prerm/would-invalidate-boot-loader-2.6.26-2-openvz-686: true
  linux-image-2.6.26-2-openvz-686/postinst/old-system-map-link-2.6.26-2-openvz-686: true
  linux-image-2.6.26-2-openvz-686/preinst/elilo-initrd-2.6.26-2-openvz-686: true
  linux-image-2.6.26-2-openvz-686/postinst/old-initrd-link-2.6.26-2-openvz-686: true
  linux-image-2.6.26-2-openvz-686/postinst/create-kimage-link-2.6.26-2-openvz-686: true
  linux-image-2.6.26-2-openvz-686/postinst/depmod-error-2.6.26-2-openvz-686: false
  linux-image-2.6.26-2-openvz-686/postinst/old-dir-initrd-link-2.6.26-2-openvz-686: true
  linux-image-2.6.26-2-openvz-686/preinst/abort-install-2.6.26-2-openvz-686:
  linux-image-2.6.26-2-openvz-686/postinst/kimage-is-a-directory:
  linux-image-2.6.26-2-openvz-686/preinst/lilo-initrd-2.6.26-2-openvz-686: true
  linux-image-2.6.26-2-openvz-686/postinst/bootloader-error-2.6.26-2-openvz-686:
  linux-image-2.6.26-2-openvz-686/postinst/depmod-error-initrd-2.6.26-2-openvz-686: false
  linux-image-2.6.26-2-openvz-686/preinst/bootloader-initrd-2.6.26-2-openvz-686: true



Reply to: