Bug#556009: linux-image-2.6.31-1-686: ath9k disassociates frequently, regression from 2.6.30
Package: linux-2.6
Version: 2.6.31-1
Severity: important
After upgrading from 2.6.30-2-686, where wireless was working fine,
the ath9k driver started frequently spontaneously disassociating.
Forcing reassociation with iwconfig wlan0 ap <mac-address> would work,
but it would spontaneously disassociate again after just a few minutes.
This appears to be:
http://bugzilla.kernel.org/show_bug.cgi?id=14267
but I'm not certain.
The message when this happens is:
[ 745.004651] wlan0: no probe response from AP 00:13:10:d3:0b:2a - disassociating
when I force reassociation, I get:
[ 788.085908] wlan0: direct probe to AP 00:13:10:d3:0b:2a try 1
[ 788.087976] wlan0 direct probe responded
[ 788.087983] wlan0: authenticate with AP 00:13:10:d3:0b:2a
[ 788.090275] wlan0: authenticated
[ 788.090281] wlan0: associate with AP 00:13:10:d3:0b:2a
[ 788.092814] wlan0: RX ReassocResp from 00:13:10:d3:0b:2a (capab=0x431 status=0 aid=2)
[ 788.092820] wlan0: associated
[ 980.011984] wlan0: no probe response from AP 00:13:10:d3:0b:2a - disassociating
As you can see, it spontaneously disassociates again after a while. The
same configuration works fine with 2.6.30-2-686.
Possibly related: shortly after the first time I booted into 2.6.31, I
got the following:
[ 397.996992] Uhhuh. NMI received for unknown reason a0 on CPU 0.
[ 397.996992] You have some hardware problem, likely on the PCI bus.
[ 397.996992] Dazed and confused, but trying to continue
[ 401.996039] wlan0: no probe response from AP 00:13:10:d3:0b:2a - disassociating
I don't know if the NMI problem is at all related to this. I don't get
that NMI error with 2.6.30-2-686.
-- Package-specific info:
** Kernel log: boot messages should be attached
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.31-1-686 (Debian 2.6.31-1) (waldi@debian.org) (gcc version 4.3.4 (Debian 4.3.4-5) ) #1 SMP Sun Oct 25 20:25:27 UTC 2009
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] NSC Geode by NSC
[ 0.000000] Cyrix CyrixInstead
[ 0.000000] Centaur CentaurHauls
[ 0.000000] Transmeta GenuineTMx86
[ 0.000000] Transmeta TransmetaCPU
[ 0.000000] UMC UMC UMC UMC
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
[ 0.000000] BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000d2000 - 00000000000d4000 (reserved)
[ 0.000000] BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007fed0000 (usable)
[ 0.000000] BIOS-e820: 000000007fed0000 - 000000007fedf000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007fedf000 - 000000007ff00000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007ff00000 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
[ 0.000000] BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff800000 - 0000000100000000 (reserved)
[ 0.000000] DMI present.
[ 0.000000] last_pfn = 0x7fed0 max_arch_pfn = 0x100000
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] init_memory_mapping: 0000000000000000-00000000373fe000
[ 0.000000] RAMDISK: 3777a000 - 37fefd54
[ 0.000000] Allocated new RAMDISK: 00100000 - 00975d54
[ 0.000000] Move RAMDISK from 000000003777a000 - 0000000037fefd53 to 00100000 - 00975d53
[ 0.000000] ACPI: RSDP 000f67d0 00024 (v02 LENOVO)
[ 0.000000] ACPI: XSDT 7fed156e 0008C (v01 LENOVO TP-7I 00001070 LTP 00000000)
[ 0.000000] ACPI: FACP 7fed1700 000F4 (v03 LENOVO TP-7I 00001070 LNVO 00000001)
[ 0.000000] ACPI Warning: 32/64X length mismatch in Gpe1Block: 0/32 20090521 tbfadt-527
[ 0.000000] ACPI Warning: Optional field Gpe1Block has zero address or length: 000000000000102C/0 20090521 tbfadt-558
[ 0.000000] ACPI: DSDT 7fed1a5e 0D21B (v01 LENOVO TP-7I 00001070 MSFT 0100000E)
[ 0.000000] ACPI: FACS 7fef4000 00040
[ 0.000000] ACPI: SSDT 7fed18b4 001AA (v01 LENOVO TP-7I 00001070 MSFT 0100000E)
[ 0.000000] ACPI: ECDT 7fedec79 00052 (v01 LENOVO TP-7I 00001070 LNVO 00000001)
[ 0.000000] ACPI: TCPA 7fedeccb 00032 (v02 LENOVO TP-7I 00001070 LNVO 00000001)
[ 0.000000] ACPI: APIC 7fedecfd 00068 (v01 LENOVO TP-7I 00001070 LNVO 00000001)
[ 0.000000] ACPI: MCFG 7feded65 0003C (v01 LENOVO TP-7I 00001070 LNVO 00000001)
[ 0.000000] ACPI: HPET 7fededa1 00038 (v01 LENOVO TP-7I 00001070 LNVO 00000001)
[ 0.000000] ACPI: SLIC 7fedee62 00176 (v01 LENOVO TP-7I 00001070 LTP 00000000)
[ 0.000000] ACPI: BOOT 7fedefd8 00028 (v01 LENOVO TP-7I 00001070 LTP 00000001)
[ 0.000000] ACPI: SSDT 7fef2697 0025F (v01 LENOVO TP-7I 00001070 INTL 20050513)
[ 0.000000] ACPI: SSDT 7fef28f6 000A6 (v01 LENOVO TP-7I 00001070 INTL 20050513)
[ 0.000000] ACPI: SSDT 7fef299c 004F7 (v01 LENOVO TP-7I 00001070 INTL 20050513)
[ 0.000000] ACPI: SSDT 7fef2e93 001D8 (v01 LENOVO TP-7I 00001070 INTL 20050513)
[ 0.000000] 1162MB HIGHMEM available.
[ 0.000000] 883MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 373fe000
[ 0.000000] low ram: 0 - 373fe000
[ 0.000000] node 0 low ram: 00000000 - 373fe000
[ 0.000000] node 0 bootmap 00009000 - 0000fe80
[ 0.000000] (9 early reservations) ==> bootmem [0000000000 - 00373fe000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
[ 0.000000] #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
[ 0.000000] #3 [0001000000 - 0001500d58] TEXT DATA BSS ==> [0001000000 - 0001500d58]
[ 0.000000] #4 [000009f000 - 0000100000] BIOS reserved ==> [000009f000 - 0000100000]
[ 0.000000] #5 [0001501000 - 0001507138] BRK ==> [0001501000 - 0001507138]
[ 0.000000] #6 [0000007000 - 0000009000] PGTABLE ==> [0000007000 - 0000009000]
[ 0.000000] #7 [0000100000 - 0000975d54] NEW RAMDISK ==> [0000100000 - 0000975d54]
[ 0.000000] #8 [0000009000 - 0000010000] BOOTMAP ==> [0000009000 - 0000010000]
[ 0.000000] found SMP MP-table at [c00f6810] f6810
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x000373fe
[ 0.000000] HighMem 0x000373fe -> 0x0007fed0
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0007fed0
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000d2000
[ 0.000000] PM: Registered nosave memory: 00000000000d2000 - 00000000000d4000
[ 0.000000] PM: Registered nosave memory: 00000000000d4000 - 00000000000dc000
[ 0.000000] PM: Registered nosave memory: 00000000000dc000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 80000000 (gap: 80000000:70000000)
[ 0.000000] NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:2 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 13 pages at c2512000, static data 31868 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 519793
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.31-1-686 root=UUID=7751f9ff-c4eb-4cac-82e7-9ba705ada1cb ro quiet
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] Initializing HighMem for node 0 (000373fe:0007fed0)
[ 0.000000] Memory: 2063496k/2095936k available (2823k kernel code, 31168k reserved, 1233k data, 376k init, 1190728k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xffd56000 - 0xfffff000 (2724 kB)
[ 0.000000] pkmap : 0xff400000 - 0xff800000 (4096 kB)
[ 0.000000] vmalloc : 0xf7bfe000 - 0xff3fe000 ( 120 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf73fe000 ( 883 MB)
[ 0.000000] .init : 0xc13f7000 - 0xc1455000 ( 376 kB)
[ 0.000000] .data : 0xc12c1e94 - 0xc13f6458 (1233 kB)
[ 0.000000] .text : 0xc1000000 - 0xc12c1e94 (2823 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] NR_IRQS:1280
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 1995.031 MHz processor.
[ 0.003241] Console: colour VGA+ 80x25
[ 0.003244] console [tty0] enabled
[ 0.003412] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.003419] Calibrating delay loop (skipped), value calculated using timer frequency.. 3990.06 BogoMIPS (lpj=7980124)
[ 0.003462] Security Framework initialized
[ 0.003468] SELinux: Disabled at boot.
[ 0.003486] Mount-cache hash table entries: 512
[ 0.003628] Initializing cgroup subsys ns
[ 0.003633] Initializing cgroup subsys cpuacct
[ 0.003637] Initializing cgroup subsys devices
[ 0.003640] Initializing cgroup subsys freezer
[ 0.003642] Initializing cgroup subsys net_cls
[ 0.003665] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.003668] CPU: L2 cache: 4096K
[ 0.003671] CPU: Physical Processor ID: 0
[ 0.003672] CPU: Processor Core ID: 0
[ 0.003676] mce: CPU supports 6 MCE banks
[ 0.003686] CPU0: Thermal monitoring enabled (TM2)
[ 0.003690] using mwait in idle threads.
[ 0.003697] Performance Counters: Core2 events, Intel PMU driver.
[ 0.003705] ... version: 2
[ 0.003707] ... bit width: 40
[ 0.003708] ... generic counters: 2
[ 0.003710] ... value mask: 000000ffffffffff
[ 0.003712] ... max period: 000000007fffffff
[ 0.003714] ... fixed-purpose counters: 3
[ 0.003716] ... counter mask: 0000000700000003
[ 0.003721] Checking 'hlt' instruction... OK.
[ 0.017099] ACPI: Core revision 20090521
[ 0.040446] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.083588] CPU0: Intel(R) Core(TM)2 CPU T7200 @ 2.00GHz stepping 06
[ 0.084001] Booting processor 1 APIC 0x1 ip 0x6000
[ 0.004000] Initializing CPU#1
[ 0.004000] Calibrating delay using timer specific routine.. 3990.03 BogoMIPS (lpj=7980079)
[ 0.004000] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.004000] CPU: L2 cache: 4096K
[ 0.004000] CPU: Physical Processor ID: 0
[ 0.004000] CPU: Processor Core ID: 1
[ 0.004000] mce: CPU supports 6 MCE banks
[ 0.004000] CPU1: Thermal monitoring enabled (TM2)
[ 0.004000] x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
[ 0.169877] CPU1: Intel(R) Core(TM)2 CPU T7200 @ 2.00GHz stepping 06
[ 0.169892] checking TSC synchronization [CPU#0 -> CPU#1]:
[ 0.172001] Measured 617460 cycles TSC warp between CPUs, turning off TSC clock.
[ 0.172001] Marking TSC unstable due to check_tsc_sync_source failed
[ 0.172070] Brought up 2 CPUs
[ 0.172073] Total of 2 processors activated (7980.10 BogoMIPS).
[ 0.172221] Booting paravirtualized kernel on bare hardware
[ 0.172221] regulator: core version 0.5
[ 0.172221] NET: Registered protocol family 16
[ 0.172221] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 0.172221] ACPI: bus type pci registered
[ 0.172276] PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 63
[ 0.172280] PCI: MCFG area at f0000000 reserved in E820
[ 0.172282] PCI: Using MMCONFIG for extended config space
[ 0.172284] PCI: Using configuration type 1 for base access
[ 0.172615] bio: create slab <bio-0> at 0
[ 0.176576] ACPI: EC: EC description table is found, configuring boot EC
[ 0.183746] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 0.192501] ACPI: Interpreter enabled
[ 0.192507] ACPI: (supports S0 S3 S4 S5)
[ 0.192531] ACPI: Using IOAPIC for interrupt routing
[ 0.204789] ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62
[ 0.204792] ACPI: EC: driver started in interrupt mode
[ 0.204839] ACPI: Power Resource [PUBS] (on)
[ 0.209136] ACPI: ACPI Dock Station Driver: 3 docks/bays found
[ 0.209621] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.209734] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.209738] pci 0000:00:01.0: PME# disabled
[ 0.209892] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.209897] pci 0000:00:1b.0: PME# disabled
[ 0.209986] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.209991] pci 0000:00:1c.0: PME# disabled
[ 0.210081] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 0.210086] pci 0000:00:1c.1: PME# disabled
[ 0.210178] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[ 0.210183] pci 0000:00:1c.2: PME# disabled
[ 0.210273] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[ 0.210278] pci 0000:00:1c.3: PME# disabled
[ 0.210681] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.210687] pci 0000:00:1d.7: PME# disabled
[ 0.210858] pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
[ 0.210863] pci 0000:00:1f.0: quirk: region 1180-11bf claimed by ICH6 GPIO
[ 0.210868] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 1600 (mask 007f)
[ 0.210873] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 15e0 (mask 000f)
[ 0.210877] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 1680 (mask 001f)
[ 0.211113] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.211118] pci 0000:00:1f.2: PME# disabled
[ 0.211698] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[ 0.211705] pci 0000:02:00.0: PME# disabled
[ 0.211970] pci 0000:03:00.0: PME# supported from D0 D1 D3hot
[ 0.211977] pci 0000:03:00.0: PME# disabled
[ 0.212317] pci 0000:15:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.212324] pci 0000:15:00.0: PME# disabled
[ 0.212397] pci 0000:00:1e.0: transparent bridge
[ 0.216911] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11)
[ 0.217107] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11)
[ 0.217301] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11)
[ 0.217494] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11)
[ 0.217686] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11)
[ 0.217880] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11)
[ 0.218072] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 *11)
[ 0.218265] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11)
[ 0.218388] PCI: Using ACPI for IRQ routing
[ 0.228017] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.228023] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.244014] pnp: PnP ACPI init
[ 0.244024] ACPI: bus type pnp registered
[ 0.248329] pnp: PnP ACPI: found 12 devices
[ 0.248331] ACPI: ACPI bus type pnp unregistered
[ 0.248334] PnPBIOS: Disabled by ACPI PNP
[ 0.248344] system 00:00: iomem range 0x0-0x9ffff could not be reserved
[ 0.248348] system 00:00: iomem range 0xc0000-0xc3fff could not be reserved
[ 0.248351] system 00:00: iomem range 0xc4000-0xc7fff could not be reserved
[ 0.248355] system 00:00: iomem range 0xc8000-0xcbfff could not be reserved
[ 0.248358] system 00:00: iomem range 0xcc000-0xcffff could not be reserved
[ 0.248361] system 00:00: iomem range 0xd0000-0xd3fff could not be reserved
[ 0.248365] system 00:00: iomem range 0xdc000-0xdffff could not be reserved
[ 0.248368] system 00:00: iomem range 0xe0000-0xe3fff could not be reserved
[ 0.248371] system 00:00: iomem range 0xe4000-0xe7fff could not be reserved
[ 0.248374] system 00:00: iomem range 0xe8000-0xebfff could not be reserved
[ 0.248378] system 00:00: iomem range 0xec000-0xeffff could not be reserved
[ 0.248381] system 00:00: iomem range 0xf0000-0xfffff could not be reserved
[ 0.248384] system 00:00: iomem range 0x100000-0x7fffffff could not be reserved
[ 0.248388] system 00:00: iomem range 0xfec00000-0xfed3ffff could not be reserved
[ 0.248391] system 00:00: iomem range 0xfed41000-0xffffffff could not be reserved
[ 0.248399] system 00:02: ioport range 0x164e-0x164f has been reserved
[ 0.248403] system 00:02: ioport range 0x1000-0x107f has been reserved
[ 0.248406] system 00:02: ioport range 0x1180-0x11bf has been reserved
[ 0.248409] system 00:02: ioport range 0x800-0x80f has been reserved
[ 0.248413] system 00:02: ioport range 0x15e0-0x15ef has been reserved
[ 0.248416] system 00:02: ioport range 0x1600-0x165f could not be reserved
[ 0.248420] system 00:02: iomem range 0xf0000000-0xf3ffffff has been reserved
[ 0.248424] system 00:02: iomem range 0xfed1c000-0xfed1ffff has been reserved
[ 0.248427] system 00:02: iomem range 0xfed14000-0xfed17fff has been reserved
[ 0.248431] system 00:02: iomem range 0xfed18000-0xfed18fff has been reserved
[ 0.248434] system 00:02: iomem range 0xfed19000-0xfed19fff has been reserved
[ 0.283213] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[ 0.283217] pci 0000:00:01.0: IO window: 0x2000-0x2fff
[ 0.283222] pci 0000:00:01.0: MEM window: 0xee100000-0xee1fffff
[ 0.283226] pci 0000:00:01.0: PREFETCH window: 0x000000d0000000-0x000000dfffffff
[ 0.283231] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
[ 0.283235] pci 0000:00:1c.0: IO window: 0x3000-0x3fff
[ 0.283242] pci 0000:00:1c.0: MEM window: 0xee000000-0xee0fffff
[ 0.283247] pci 0000:00:1c.0: PREFETCH window: disabled
[ 0.283252] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:03
[ 0.283256] pci 0000:00:1c.1: IO window: 0x4000-0x5fff
[ 0.283263] pci 0000:00:1c.1: MEM window: 0xec000000-0xedffffff
[ 0.283269] pci 0000:00:1c.1: PREFETCH window: 0x000000e4000000-0x000000e40fffff
[ 0.283277] pci 0000:00:1c.2: PCI bridge, secondary bus 0000:04
[ 0.283281] pci 0000:00:1c.2: IO window: 0x6000-0x7fff
[ 0.283287] pci 0000:00:1c.2: MEM window: 0xe8000000-0xe9ffffff
[ 0.283293] pci 0000:00:1c.2: PREFETCH window: 0x000000e4100000-0x000000e41fffff
[ 0.283301] pci 0000:00:1c.3: PCI bridge, secondary bus 0000:0c
[ 0.283305] pci 0000:00:1c.3: IO window: 0x8000-0x9fff
[ 0.283312] pci 0000:00:1c.3: MEM window: 0xea000000-0xebffffff
[ 0.283317] pci 0000:00:1c.3: PREFETCH window: 0x000000e4200000-0x000000e42fffff
[ 0.283328] pci 0000:15:00.0: CardBus bridge, secondary bus 0000:16
[ 0.283330] pci 0000:15:00.0: IO window: 0x00a000-0x00a0ff
[ 0.283337] pci 0000:15:00.0: IO window: 0x00a400-0x00a4ff
[ 0.283343] pci 0000:15:00.0: PREFETCH window: 0xe0000000-0xe3ffffff
[ 0.283349] pci 0000:15:00.0: MEM window: 0x80000000-0x83ffffff
[ 0.283356] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:15
[ 0.283360] pci 0000:00:1e.0: IO window: 0xa000-0xdfff
[ 0.283366] pci 0000:00:1e.0: MEM window: 0xe4300000-0xe7ffffff
[ 0.283372] pci 0000:00:1e.0: PREFETCH window: 0x000000e0000000-0x000000e3ffffff
[ 0.283387] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.283402] pci 0000:00:1c.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 0.283418] pci 0000:00:1c.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 0.283433] pci 0000:00:1c.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22
[ 0.283448] pci 0000:00:1c.3: PCI INT D -> GSI 23 (level, low) -> IRQ 23
[ 0.283459] pci 0000:00:1e.0: enabling device (0005 -> 0007)
[ 0.283477] pci 0000:15:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.283614] NET: Registered protocol family 2
[ 0.283706] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.284030] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.284449] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.284666] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.284668] TCP reno registered
[ 0.284754] NET: Registered protocol family 1
[ 0.284814] Unpacking initramfs...
[ 0.531249] Freeing initrd memory: 8663k freed
[ 0.536293] Simple Boot Flag at 0x35 set to 0x1
[ 0.536694] audit: initializing netlink socket (disabled)
[ 0.536718] type=2000 audit(1258079162.536:1): initialized
[ 0.537092] highmem bounce pool size: 64 pages
[ 0.537097] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.537211] VFS: Disk quotas dquot_6.5.2
[ 0.537248] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.537311] msgmni has been set to 1723
[ 0.537503] alg: No test for stdrng (krng)
[ 0.537536] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.537540] io scheduler noop registered
[ 0.537542] io scheduler anticipatory registered
[ 0.537544] io scheduler deadline registered
[ 0.537562] io scheduler cfq registered (default)
[ 0.538691] isapnp: Scanning for PnP cards...
[ 0.893603] isapnp: No Plug & Play device found
[ 0.894789] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.895228] PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
[ 0.903006] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.903013] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.903062] mice: PS/2 mouse device common for all mice
[ 0.903112] rtc_cmos 00:07: RTC can wake from S4
[ 0.903145] rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
[ 0.903176] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 0.903189] cpuidle: using governor ladder
[ 0.903191] cpuidle: using governor menu
[ 0.903195] No iBFT detected.
[ 0.903513] TCP cubic registered
[ 0.903567] NET: Registered protocol family 10
[ 0.903990] lo: Disabled Privacy Extensions
[ 0.904300] Mobile IPv6
[ 0.904303] NET: Registered protocol family 17
[ 0.904326] Using IPI No-Shortcut mode
[ 0.904386] registered taskstats version 1
[ 0.904530] rtc_cmos 00:07: setting system clock to 2009-11-13 02:26:03 UTC (1258079163)
[ 0.904608] Freeing unused kernel memory: 376k freed
[ 0.904847] Write protecting the kernel text: 2824k
[ 0.904877] Write protecting the kernel read-only data: 844k
[ 0.907260] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 1.024258] thermal LNXTHERM:01: registered as thermal_zone0
[ 1.024267] ACPI: Thermal Zone [THM0] (37 C)
[ 1.025742] thermal LNXTHERM:02: registered as thermal_zone1
[ 1.025750] ACPI: Thermal Zone [THM1] (38 C)
[ 1.105129] SCSI subsystem initialized
[ 1.107678] Linux agpgart interface v0.103
[ 1.116033] acpi device:08: registered as cooling_device0
[ 1.116211] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:06/device:07/input/input1
[ 1.116219] ACPI: Video Device [VID1] (multi-head: yes rom: no post: no)
[ 1.127752] Uniform Multi-Platform E-IDE driver
[ 1.150918] piix 0000:00:1f.1: IDE controller (0x8086:0x27df rev 0x02)
[ 1.150935] PIIX_IDE 0000:00:1f.1: PCI INT C -> GSI 16 (level, low) -> IRQ 16
[ 1.150948] piix 0000:00:1f.1: IDE port disabled
[ 1.150958] piix 0000:00:1f.1: not 100% native mode: will probe irqs later
[ 1.150966] ide0: BM-DMA at 0x1880-0x1887
[ 1.151725] usbcore: registered new interface driver usbfs
[ 1.151750] usbcore: registered new interface driver hub
[ 1.151782] usbcore: registered new device driver usb
[ 1.154058] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.167610] e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2
[ 1.167613] e1000e: Copyright (c) 1999-2008 Intel Corporation.
[ 1.167656] e1000e 0000:02:00.0: Disabling L1 ASPM
[ 1.167675] e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.229052] e1000e 0000:02:00.0: Warning: detected ASPM enabled in EEPROM
[ 1.289975] 0000:02:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:1a:6b:67:47:20
[ 1.289978] 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection
[ 1.290055] 0000:02:00.0: eth0: MAC: 2, PHY: 2, PBA No: 005301-003
[ 1.885421] hda: HL-DT-ST DVDRAM GSA-4083N, ATAPI CD/DVD-ROM drive
[ 2.221820] hda: UDMA/33 mode selected
[ 2.222291] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 2.227881] ehci_hcd 0000:00:1d.7: power state changed by ACPI to D0
[ 2.227894] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 2.227914] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 2.227943] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 2.231861] ehci_hcd 0000:00:1d.7: debug port 1
[ 2.231882] ehci_hcd 0000:00:1d.7: irq 19, io mem 0xee404000
[ 2.244013] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 2.244038] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.244041] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.244043] usb usb1: Product: EHCI Host Controller
[ 2.244046] usb usb1: Manufacturer: Linux 2.6.31-1-686 ehci_hcd
[ 2.244048] usb usb1: SerialNumber: 0000:00:1d.7
[ 2.244112] usb usb1: configuration #1 chosen from 1 choice
[ 2.244145] hub 1-0:1.0: USB hub found
[ 2.244153] hub 1-0:1.0: 8 ports detected
[ 2.244232] ahci 0000:00:1f.2: PCI INT B -> GSI 16 (level, low) -> IRQ 16
[ 2.244343] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 1.5 Gbps 0x1 impl SATA mode
[ 2.244347] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part
[ 2.244911] scsi0 : ahci
[ 2.245058] scsi1 : ahci
[ 2.245159] scsi2 : ahci
[ 2.245262] scsi3 : ahci
[ 2.245346] ata1: SATA max UDMA/133 abar m1024@0xee404400 port 0xee404500 irq 30
[ 2.245349] ata2: DUMMY
[ 2.245351] ata3: DUMMY
[ 2.245353] ata4: DUMMY
[ 2.277325] uhci_hcd: USB Universal Host Controller Interface driver
[ 2.277900] uhci_hcd 0000:00:1d.0: power state changed by ACPI to D0
[ 2.277909] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 2.279003] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 2.279016] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 2.279055] uhci_hcd 0000:00:1d.0: irq 16, io base 0x00001800
[ 2.279094] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.279097] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.279100] usb usb2: Product: UHCI Host Controller
[ 2.279102] usb usb2: Manufacturer: Linux 2.6.31-1-686 uhci_hcd
[ 2.279105] usb usb2: SerialNumber: 0000:00:1d.0
[ 2.279203] usb usb2: configuration #1 chosen from 1 choice
[ 2.279271] hub 2-0:1.0: USB hub found
[ 2.279279] hub 2-0:1.0: 2 ports detected
[ 2.279333] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 2.279344] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 2.279352] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 2.279388] uhci_hcd 0000:00:1d.1: irq 17, io base 0x00001820
[ 2.279422] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.279425] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.279427] usb usb3: Product: UHCI Host Controller
[ 2.279430] usb usb3: Manufacturer: Linux 2.6.31-1-686 uhci_hcd
[ 2.279432] usb usb3: SerialNumber: 0000:00:1d.1
[ 2.279536] usb usb3: configuration #1 chosen from 1 choice
[ 2.279603] hub 3-0:1.0: USB hub found
[ 2.279611] hub 3-0:1.0: 2 ports detected
[ 2.280718] uhci_hcd 0000:00:1d.2: power state changed by ACPI to D0
[ 2.280727] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 2.280738] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 2.280752] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 2.280789] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001840
[ 2.280826] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.280829] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.280832] usb usb4: Product: UHCI Host Controller
[ 2.280834] usb usb4: Manufacturer: Linux 2.6.31-1-686 uhci_hcd
[ 2.280837] usb usb4: SerialNumber: 0000:00:1d.2
[ 2.280932] usb usb4: configuration #1 chosen from 1 choice
[ 2.280997] hub 4-0:1.0: USB hub found
[ 2.281014] hub 4-0:1.0: 2 ports detected
[ 2.281067] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 2.281078] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 2.281086] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[ 2.281114] uhci_hcd 0000:00:1d.3: irq 19, io base 0x00001860
[ 2.281147] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.281150] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.281153] usb usb5: Product: UHCI Host Controller
[ 2.281155] usb usb5: Manufacturer: Linux 2.6.31-1-686 uhci_hcd
[ 2.281158] usb usb5: SerialNumber: 0000:00:1d.3
[ 2.281246] usb usb5: configuration #1 chosen from 1 choice
[ 2.281310] hub 5-0:1.0: USB hub found
[ 2.281318] hub 5-0:1.0: 2 ports detected
[ 2.788029] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2.789362] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
[ 2.789365] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 filtered out
[ 2.790422] ata1.00: ATA-7: HTS541080G9SA00, MB4IC65R, max UDMA/100
[ 2.790425] ata1.00: 156301488 sectors, multi 16: LBA48
[ 2.791966] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
[ 2.791969] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 filtered out
[ 2.793050] ata1.00: configured for UDMA/100
[ 2.810429] ata1.00: configured for UDMA/100
[ 2.810433] ata1: EH complete
[ 2.810539] scsi 0:0:0:0: Direct-Access ATA HTS541080G9SA00 MB4I PQ: 0 ANSI: 5
[ 2.818961] ide-cd driver 5.00
[ 2.820786] ide-cd: hda: ATAPI 24X DVD-ROM DVD-R/RAM CD-R/RW drive, 2048kB Cache
[ 2.820793] Uniform CD-ROM driver Revision: 3.20
[ 2.826141] sd 0:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ 2.826188] sd 0:0:0:0: [sda] Write Protect is off
[ 2.826217] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.826340] sda: sda1 sda2 < sda5 >
[ 3.225959] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.485588] PM: Starting manual resume from disk
[ 3.553783] kjournald starting. Commit interval 5 seconds
[ 3.553793] EXT3-fs: mounted filesystem with ordered data mode.
[ 5.298302] udev: starting version 147
[ 5.807372] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 5.807381] ACPI: Power Button [PWRF]
[ 5.807454] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input3
[ 5.808046] ACPI: Lid Switch [LID]
[ 5.808106] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input4
[ 5.808114] ACPI: Sleep Button [SLPB]
[ 6.040362] ACPI: SSDT 7fef1d36 00282 (v01 PmRef Cpu0Ist 00000100 INTL 20050513)
[ 6.041012] ACPI: SSDT 7fef203d 0065A (v01 PmRef Cpu0Cst 00000100 INTL 20050513)
[ 6.047029] ACPI: AC Adapter [AC] (on-line)
[ 6.048283] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 6.048327] processor LNXCPU:00: registered as cooling_device1
[ 6.048332] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 6.048756] ACPI: SSDT 7fef1c6e 000C8 (v01 PmRef Cpu1Ist 00000100 INTL 20050513)
[ 6.049188] ACPI: SSDT 7fef1fb8 00085 (v01 PmRef Cpu1Cst 00000100 INTL 20050513)
[ 6.050900] ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
[ 6.050927] processor LNXCPU:01: registered as cooling_device2
[ 6.050932] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 6.054848] Non-volatile memory driver v1.3
[ 6.089696] ACPI: Battery Slot [BAT0] (battery present)
[ 6.748067] cfg80211: Using static regulatory domain info
[ 6.748070] cfg80211: Regulatory domain: US
[ 6.748072] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 6.748075] (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
[ 6.748078] (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 6.748081] (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 6.748084] (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 6.748087] (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 6.748090] (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
[ 6.748269] cfg80211: Calling CRDA for country: US
[ 6.792049] NET: Registered protocol family 23
[ 6.795487] input: PC Speaker as /devices/platform/pcspkr/input/input5
[ 6.808422] yenta_cardbus 0000:15:00.0: CardBus bridge found [17aa:2012]
[ 6.808450] yenta_cardbus 0000:15:00.0: Using INTVAL to route CSC interrupts to PCI
[ 6.808452] yenta_cardbus 0000:15:00.0: Routing CardBus interrupts to PCI
[ 6.808459] yenta_cardbus 0000:15:00.0: TI: mfunc 0x01d01002, devctl 0x64
[ 6.859572] intel_rng: FWH not detected
[ 6.928451] i801_smbus 0000:00:1f.3: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 6.981590] thinkpad_acpi: ThinkPad ACPI Extras v0.23
[ 6.981593] thinkpad_acpi: http://ibm-acpi.sf.net/
[ 6.981595] thinkpad_acpi: ThinkPad BIOS 7IET26WW (1.07 ), EC 79HT50WW-1.07
[ 6.981597] thinkpad_acpi: Lenovo ThinkPad T60p, model 8743CTO
[ 6.982244] thinkpad_acpi: radio switch found; radios are enabled
[ 6.982337] thinkpad_acpi: This ThinkPad has standard ACPI backlight brightness control, supported by the ACPI video driver
[ 6.982339] thinkpad_acpi: Disabling thinkpad-acpi brightness events by default...
[ 6.990293] Registered led device: tpacpi::thinklight
[ 6.990355] Registered led device: tpacpi::power
[ 6.990409] Registered led device: tpacpi::standby
[ 6.990476] Registered led device: tpacpi::thinkvantage
[ 6.993293] thinkpad_acpi: Standard ACPI backlight interface available, not loading native one.
[ 6.993650] input: ThinkPad Extra Buttons as /devices/virtual/input/input6
[ 7.039186] nsc-ircc 00:0a: activated
[ 7.039222] nsc-ircc, chip->init
[ 7.039237] nsc-ircc, Found chip at base=0x164e
[ 7.039279] nsc-ircc, driver loaded (Dag Brattli)
[ 7.039917] IrDA: Registered device irda0
[ 7.039919] nsc-ircc, Using dongle: IBM31T1100 or Temic TFDS6000/TFDS6500
[ 7.040914] yenta_cardbus 0000:15:00.0: ISA IRQ mask 0x0cf0, PCI irq 16
[ 7.040918] yenta_cardbus 0000:15:00.0: Socket status: 30000007
[ 7.040924] yenta_cardbus 0000:15:00.0: pcmcia: parent PCI bridge I/O window: 0xa000 - 0xdfff
[ 7.040927] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa000-0xdfff: clean.
[ 7.041925] yenta_cardbus 0000:15:00.0: pcmcia: parent PCI bridge Memory window: 0xe4300000 - 0xe7ffffff
[ 7.041929] yenta_cardbus 0000:15:00.0: pcmcia: parent PCI bridge Memory window: 0xe0000000 - 0xe3ffffff
[ 7.112133] ath9k 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 7.461823] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x81a0b1, caps: 0xa04793/0x300000
[ 7.461828] serio: Synaptics pass-through port at isa0060/serio1/input0
[ 7.502775] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input7
[ 7.633063] usb 5-1: new full speed USB device using uhci_hcd and address 2
[ 7.734725] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: clean.
[ 7.736912] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
[ 7.737849] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: clean.
[ 7.738604] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: clean.
[ 7.739548] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
[ 7.809068] usb 5-1: New USB device found, idVendor=0a5c, idProduct=2110
[ 7.809071] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 7.809074] usb 5-1: Product: BCM2045B
[ 7.809076] usb 5-1: Manufacturer: Broadcom Corp
[ 7.809147] usb 5-1: configuration #1 chosen from 1 choice
[ 7.839042] Registered led device: ath9k-phy0::radio
[ 7.839060] Registered led device: ath9k-phy0::assoc
[ 7.839077] Registered led device: ath9k-phy0::tx
[ 7.839096] Registered led device: ath9k-phy0::rx
[ 7.839106] phy0: Atheros AR5418 MAC/BB Rev:2 AR5133 RF Rev:81: mem=0xf83a0000, irq=17
[ 7.846018] HDA Intel 0000:00:1b.0: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 7.846023] hda_intel: probe_mask set to 0x1 for device 17aa:2010
[ 8.059387] Bluetooth: Core ver 2.15
[ 8.059750] NET: Registered protocol family 31
[ 8.059752] Bluetooth: HCI device and connection manager initialized
[ 8.059755] Bluetooth: HCI socket layer initialized
[ 8.133558] Bluetooth: Generic Bluetooth USB driver ver 0.5
[ 8.133674] usbcore: registered new interface driver btusb
[ 8.253857] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input8
[ 9.594837] Adding 2650684k swap on /dev/sda5. Priority:-1 extents:1 across:2650684k
[ 9.798443] EXT3 FS on sda1, internal journal
[ 9.929756] loop: module loaded
[ 12.152313] fuse init (API version 7.12)
[ 12.815877] IBM TrackPoint firmware: 0x0e, buttons: 3/3
[ 13.032185] input: TPPS/2 IBM TrackPoint as /devices/platform/i8042/serio1/serio2/input/input9
[ 23.001065] Clocksource tsc unstable (delta = -222081479 ns)
[ 24.311255] input: /usr/sbin/thinkpad-keys as /devices/virtual/input/input10
[ 29.448250] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 33.481955] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 33.496675] [drm] Initialized drm 1.1.0 20060810
[ 33.516380] pci 0000:01:00.0: power state changed by ACPI to D0
[ 33.516403] pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 33.516786] [drm] Initialized radeon 1.31.0 20080528 for 0000:01:00.0 on minor 0
[ 33.851289] [drm] Setting GART location based on new memory map
[ 33.852978] [drm] Loading R500 Microcode
[ 33.853101] platform radeon_cp.0: firmware: requesting radeon/R520_cp.bin
[ 33.897839] [drm] Num pipes: 1
[ 33.897857] [drm] writeback test succeeded in 2 usecs
[ 88.958504] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
** Model information
Lenovo Thinkpad T60p
** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
# The wireless network interface
allow-hotplug wlan0
auto wlan0
iface wlan0 inet dhcp
dns-nameservers 171.64.7.121 171.64.7.77 171.64.7.99 171.64.7.55
dns-search stanford.edu
wireless-essid Eyrie
wireless-key <redacted> restricted
wireless-channel 3
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub [8086:27a0] (rev 03)
Subsystem: Lenovo ThinkPad T60 [17aa:2015]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:01.0 PCI bridge [0604]: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express PCI Express Root Port [8086:27a1] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: ee100000-ee1fffff
Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1b.0 Audio device [0403]: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller [8086:27d8] (rev 02)
Subsystem: Lenovo ThinkPad T60/R60 series [17aa:2010]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at ee400000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
00:1c.0 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 [8086:27d0] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: ee000000-ee0fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1c.1 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 [8086:27d2] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00004000-00005fff
Memory behind bridge: ec000000-edffffff
Prefetchable memory behind bridge: 00000000e4000000-00000000e40fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1c.2 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3 [8086:27d4] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=0b, sec-latency=0
I/O behind bridge: 00006000-00007fff
Memory behind bridge: e8000000-e9ffffff
Prefetchable memory behind bridge: 00000000e4100000-00000000e41fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1c.3 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 4 [8086:27d6] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0c, subordinate=13, sec-latency=0
I/O behind bridge: 00008000-00009fff
Memory behind bridge: ea000000-ebffffff
Prefetchable memory behind bridge: 00000000e4200000-00000000e42fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1d.0 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 [8086:27c8] (rev 02) (prog-if 00 [UHCI])
Subsystem: Lenovo ThinkPad T60/R60 series [17aa:200a]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at 1800 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 [8086:27c9] (rev 02) (prog-if 00 [UHCI])
Subsystem: Lenovo ThinkPad T60/R60 series [17aa:200a]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at 1820 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 [8086:27ca] (rev 02) (prog-if 00 [UHCI])
Subsystem: Lenovo ThinkPad T60/R60 series [17aa:200a]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 1840 [size=32]
Kernel driver in use: uhci_hcd
00:1d.3 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 [8086:27cb] (rev 02) (prog-if 00 [UHCI])
Subsystem: Lenovo ThinkPad T60/R60 series [17aa:200a]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 19
Region 4: I/O ports at 1860 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller [8086:27cc] (rev 02) (prog-if 20 [EHCI])
Subsystem: Lenovo ThinkPad T60/R60 series [17aa:200b]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 19
Region 0: Memory at ee404000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=15, subordinate=18, sec-latency=32
I/O behind bridge: 0000a000-0000dfff
Memory behind bridge: e4300000-e7ffffff
Prefetchable memory behind bridge: 00000000e0000000-00000000e3ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge [8086:27b9] (rev 02)
Subsystem: Lenovo ThinkPad T60/R60 series [17aa:2009]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.1 IDE interface [0101]: Intel Corporation 82801G (ICH7 Family) IDE Controller [8086:27df] (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Lenovo ThinkPad T60/R60 series [17aa:200c]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 1880 [size=16]
Kernel driver in use: PIIX_IDE
00:1f.2 SATA controller [0106]: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA AHCI Controller [8086:27c5] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Lenovo ThinkPad T60/R60 series [17aa:200d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 30
Region 0: I/O ports at 18c8 [size=8]
Region 1: I/O ports at 18ac [size=4]
Region 2: I/O ports at 18c0 [size=8]
Region 3: I/O ports at 18a8 [size=4]
Region 4: I/O ports at 18b0 [size=16]
Region 5: Memory at ee404400 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 82801G (ICH7 Family) SMBus Controller [8086:27da] (rev 02)
Subsystem: Lenovo ThinkPad T60/R60 series [17aa:200f]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at 18e0 [size=32]
Kernel driver in use: i801_smbus
01:00.0 VGA compatible controller [0300]: ATI Technologies Inc M56GL [Mobility FireGL V5250] [1002:71d4] (prog-if 00 [VGA controller])
Subsystem: Lenovo Device [17aa:20a4]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 1: I/O ports at 2000 [size=256]
Region 2: Memory at ee100000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at ee120000 [disabled] [size=128K]
Capabilities: <access denied>
02:00.0 Ethernet controller [0200]: Intel Corporation 82573L Gigabit Ethernet Controller [8086:109a]
Subsystem: Lenovo ThinkPad T60 [17aa:2001]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 29
Region 0: Memory at ee000000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 3000 [size=32]
Capabilities: <access denied>
Kernel driver in use: e1000e
03:00.0 Network controller [0280]: Atheros Communications Inc. AR5008 Wireless Network Adapter [168c:0024] (rev 01)
Subsystem: Atheros Communications Inc. Device [168c:0033]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at edf00000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: ath9k
15:00.0 CardBus bridge [0607]: Texas Instruments PCI1510 PC card Cardbus Controller [104c:ac56]
Subsystem: Lenovo ThinkPad T60/R60 series [17aa:2012]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at e4300000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=15, secondary=16, subordinate=17, sec-latency=176
Memory window 0: e0000000-e3fff000 (prefetchable)
Memory window 1: 88000000-8bfff000
I/O window 0: 0000a000-0000a0ff
I/O window 1: 0000a400-0000a4ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
** USB devices:
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 002: ID 0a5c:2110 Broadcom Corp. Bluetooth Controller
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: squeeze/sid
APT prefers unstable
APT policy: (500, 'unstable'), (1, 'experimental')
Architecture: i386 (i686)
Kernel: Linux 2.6.30-2-686 (SMP w/2 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-2.6.31-1-686 depends on:
ii debconf [debconf-2.0] 1.5.28 Debian configuration management sy
ii initramfs-tools [linux-initra 0.93.4 tools for generating an initramfs
ii module-init-tools 3.11-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.31-1-686 recommends:
ii firmware-linux-free 2.6.31-1 Binary firmware for various driver
ii libc6-i686 2.10.1-6 GNU C Library: Shared libraries [i
Versions of packages linux-image-2.6.31-1-686 suggests:
pn grub | lilo <none> (no description available)
pn linux-doc-2.6.31 <none> (no description available)
Versions of packages linux-image-2.6.31-1-686 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
ii firmware-linux 0.21 Binary firmware for various driver
ii firmware-linux-nonfree 0.21 Binary firmware for various driver
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
-- debconf information:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.31-1-686/postinst/missing-firmware-2.6.31-1-686:
linux-image-2.6.31-1-686/postinst/bootloader-error-2.6.31-1-686:
linux-image-2.6.31-1-686/prerm/would-invalidate-boot-loader-2.6.31-1-686: true
linux-image-2.6.31-1-686/prerm/removing-running-kernel-2.6.31-1-686: true
linux-image-2.6.31-1-686/postinst/bootloader-test-error-2.6.31-1-686:
linux-image-2.6.31-1-686/postinst/depmod-error-initrd-2.6.31-1-686: false
Reply to: