Bug#554619: linux-image-2.6.26-2-686: rt2500pci module has unreliable and slow connection speed
Package: linux-image-2.6.26-2-686
Version: 2.6.26-19lenny2
Severity: normal
I get very slow connection speeds with this module around 40 KB/s
what should be 700 - 800 KB/s. I connect through a router with WPA encryption.
At first I had the problem that the wlan card set the
speed of the connection to 1 Mb/s. I solved that problem with the
following entry in /etc/network/interfaces:
allow-hotplug wlan0
iface wlan0 inet static
pre-up iwconfig wlan0 rate 54M
wpa-driver wext
wpa-ssid
wpa-psk ""
network 192.168.178.0
address 192.168.178.200
netmask 255.255.255.0
broadcast 192.168.178.255
gateway 192.168.178.1
dns-nameservers 192.168.178.1
Now it shows 54 MB/s in iwconfig:
wlan0 IEEE 802.11 ESSID:""
Mode:Managed Frequency:2.412 GHz Access Point: 00:
Bit Rate=54 Mb/s Tx-Power=20 dBm
Retry min limit:7 RTS thr:off Fragment thr=2352 B
Encryption key:2 [2]
Link Quality=72/100 Signal level=-63 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
It worked for quite a while however lately I can only download with about 40 KB/s.
The rt2500 module build from the package rt2500-source works without problems.
Thanks for help.
-- Package-specific info:
** Version:
Linux version 2.6.26-2-686 (Debian 2.6.26-19lenny2) (dannf@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 SMP Wed Nov 4 20:45:37 UTC 2009
** Command line:
root=/dev/hda1 ro
** Tainted: P (1)
** Kernel log:
[ 6.356151] input,hidraw1: USB HID v1.11 Mouse [Microsft Microsoft Wireless Desktop Receiver 3.1A] on usb-0000:00:02.0-1
[ 6.361385] input: Logitech USB Gaming Mouse as /class/input/input2
[ 6.376102] input,hidraw2: USB HID v1.11 Mouse [Logitech USB Gaming Mouse] on usb-0000:00:02.0-2
[ 6.381341] hda: max request size: 128KiB
[ 6.381905] hda: 160086528 sectors (81964 MB) w/2048KiB Cache, CHS=65535/16/63
[ 6.382851] hda: cache flushes supported
[ 6.382953] hda:<6>hiddev96hidraw3: USB HID v1.11 Device [Logitech USB Gaming Mouse] on usb-0000:00:02.0-2
[ 6.385229] usbcore: registered new interface driver usbhid
[ 6.385281] usbhid: v2.6:USB HID core driver
[ 6.392784] hda1 hda2 < hda5 >
[ 6.414901] hdc: ATAPI 32X CD-ROM CD-R/RW drive, 4096kB Cache
[ 6.415084] Uniform CD-ROM driver Revision: 3.20
[ 6.685061] device-mapper: uevent: version 1.0.3
[ 6.687376] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
[ 6.713660] PM: Starting manual resume from disk
[ 6.779493] kjournald starting. Commit interval 5 seconds
[ 6.779556] EXT3-fs: mounted filesystem with ordered data mode.
[ 8.856162] udevd version 125 started
[ 10.023353] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x5000
[ 10.023434] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x5040
[ 10.066272] input: Power Button (FF) as /class/input/input3
[ 10.092068] ACPI: Power Button (FF) [PWRF]
[ 10.092210] input: Power Button (CM) as /class/input/input4
[ 10.124089] ACPI: Power Button (CM) [PWRB]
[ 10.935505] Bluetooth: Core ver 2.11
[ 10.964162] NET: Registered protocol family 31
[ 10.964216] Bluetooth: HCI device and connection manager initialized
[ 10.964269] Bluetooth: HCI socket layer initialized
[ 10.999565] Bluetooth: HCI USB driver ver 2.9
[ 11.001174] usbcore: registered new interface driver hci_usb
[ 11.287501] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 11.304025] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 11.546774] input: PC Speaker as /class/input/input5
[ 11.834807] gameport: EMU10K1 is pci0000:02:08.1/gameport0, io 0xbc00, speed 1193kHz
[ 11.986870] parport_pc 00:06: reported by Plug and Play ACPI
[ 11.986972] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[ 12.110002] gameport: NS558 PnP Gameport is pnp00:0b/gameport0, io 0x200, speed 917kHz
[ 12.343924] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 18
[ 12.343987] ACPI: PCI Interrupt 0000:02:07.0[A] -> Link [LNKB] -> GSI 18 (level, low) -> IRQ 18
[ 12.357655] phy0: Selected rate control algorithm 'pid'
[ 12.893158] Registered led device: rt2500pci-phy0:radio
[ 13.146605] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 17
[ 13.146668] ACPI: PCI Interrupt 0000:02:08.0[A] -> Link [LNKC] -> GSI 17 (level, low) -> IRQ 17
[ 13.920339] Adding 2650684k swap on /dev/hda5. Priority:-1 extents:1 across:2650684k
[ 14.392194] EXT3 FS on hda1, internal journal
[ 14.621159] loop: module loaded
[ 14.701973] it87: Found IT8712F chip at 0xd00, revision 7
[ 14.702035] it87: in3 is VCC (+5V)
[ 14.702080] it87: in7 is VCCH (+5V Stand-By)
[ 17.193487] eth0: no link during initialization.
[ 18.096313] powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3200+ processors (1 cpu cores) (version 2.20.00)
[ 18.096313] powernow-k8: 0 : fid 0xe (2200 MHz), vid 0x2
[ 18.096313] powernow-k8: 1 : fid 0xc (2000 MHz), vid 0x6
[ 18.096313] powernow-k8: 2 : fid 0xa (1800 MHz), vid 0xa
[ 18.096313] powernow-k8: 3 : fid 0x2 (1000 MHz), vid 0x12
[ 18.820488] wlan0: Initial auth_alg=0
[ 18.820496] wlan0: authenticate with AP 00:
[ 18.823099] wlan0: RX authentication from 00: (alg=0 transaction=2 status=0)
[ 18.823103] wlan0: authenticated
[ 18.823106] wlan0: associate with AP 00:
[ 18.826750] wlan0: RX AssocResp from 00: (capab=0x431 status=0 aid=1)
[ 18.826756] wlan0: associated
[ 18.826765] wlan0: failed to set TX queue parameters for queue 2
[ 18.826767] wlan0: failed to set TX queue parameters for queue 3
[ 18.826771] wlan0: CTS protection enabled (BSSID=00:)
[ 18.826774] wlan0: switched to short barker preamble (BSSID=00:)
[ 18.968094] padlock: VIA PadLock not detected.
[ 19.216160] Marking TSC unstable due to: cpufreq changes.
[ 19.249971] lp0: using parport0 (interrupt-driven).
[ 19.279417] ppdev: user-space parallel port driver
[ 19.724027] Clocksource tsc unstable (delta = -272729916 ns)
[ 20.013263] NET: Registered protocol family 10
[ 20.014108] lo: Disabled Privacy Extensions
[ 20.015125] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 23.467378] vboxdrv: Trying to deactivate the NMI watchdog permanently...
[ 23.467390] vboxdrv: Successfully done.
[ 23.467394] vboxdrv: Found 1 processor cores.
[ 23.467531] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[ 23.467608] vboxdrv: Successfully loaded version 3.0.10 (interface 0x000e0001).
[ 24.127995] warning: `ntpd' uses 32-bit capabilities (legacy support in use)
[ 26.442538] Bluetooth: L2CAP ver 2.9
[ 26.442600] Bluetooth: L2CAP socket layer initialized
[ 26.491035] Bluetooth: RFCOMM socket layer initialized
[ 26.491117] Bluetooth: RFCOMM TTY layer initialized
[ 26.491170] Bluetooth: RFCOMM ver 1.8
[ 26.653323] Bluetooth: SCO (Voice Link) ver 0.5
[ 26.653401] Bluetooth: SCO socket layer initialized
[ 26.872588] Bluetooth: BNEP (Ethernet Emulation) ver 1.2
[ 26.872668] Bluetooth: BNEP filters: protocol multicast
[ 26.922558] Bridge firewalling registered
[ 26.925151] pan0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
[ 30.840020] wlan0: no IPv6 routers present
[ 31.683203] nvidia: module license 'NVIDIA' taints kernel.
[ 31.948288] ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 16
[ 31.948310] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKE] -> GSI 16 (level, low) -> IRQ 16
[ 31.948808] NVRM: loading NVIDIA UNIX x86 Kernel Module 173.14.20 Thu Jun 25 19:23:24 PDT 2009
[ 32.189679] agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
[ 32.189702] agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
[ 32.189743] agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
[ 92.060853] process `skype' is using obsolete setsockopt SO_BSDCOMPAT
** Loaded modules:
Module Size Used by
nvidia 7081896 24
binfmt_misc 7560 1
bridge 40024 0
bnep 10304 2
sco 8640 2
rfcomm 28272 4
l2cap 17248 16 bnep,rfcomm
vboxnetadp 67944 0
vboxnetflt 73384 0
vboxdrv 103784 1 vboxnetflt
ipv6 235396 20
ppdev 6468 0
lp 8164 0
aes_i586 7744 1
aes_generic 29256 1 aes_i586
powernow_k8 12036 0
cpufreq_powersave 1856 0
cpufreq_ondemand 6476 1
cpufreq_conservative 5960 0
cpufreq_stats 3776 0
freq_table 4224 3 powernow_k8,cpufreq_ondemand,cpufreq_stats
cpufreq_userspace 3172 0
it87 17904 0
hwmon_vid 2720 1 it87
sbp2 18572 0
loop 12748 0
snd_emu10k1_synth 5664 0
snd_emux_synth 27936 1 snd_emu10k1_synth
snd_seq_virmidi 4896 1 snd_emux_synth
snd_seq_midi_emul 5376 1 snd_emux_synth
snd_emu10k1 115200 3 snd_emu10k1_synth
snd_cs4232 11380 0
snd_ac97_codec 88452 1 snd_emu10k1
snd_opl3_lib 9344 1 snd_cs4232
ac97_bus 1728 1 snd_ac97_codec
snd_util_mem 4032 2 snd_emux_synth,snd_emu10k1
arc4 1824 2
snd_cs4231_lib 20512 1 snd_cs4232
snd_hwdep 6212 3 snd_emux_synth,snd_emu10k1,snd_opl3_lib
snd_seq_dummy 2660 0
ecb 2624 2
crypto_blkcipher 15236 1 ecb
snd_pcm_oss 32800 0
snd_mixer_oss 12320 1 snd_pcm_oss
snd_pcm 62660 5 snd_emu10k1,snd_ac97_codec,snd_cs4231_lib,snd_pcm_oss
snd_page_alloc 7816 3 snd_emu10k1,snd_cs4231_lib,snd_pcm
snd_seq_oss 24992 0
rt2500pci 17152 0
rt2x00pci 7648 1 rt2500pci
rt2x00lib 22432 2 rt2500pci,rt2x00pci
firmware_class 6816 2 snd_emu10k1,rt2x00lib
snd_mpu401 6152 0
snd_mpu401_uart 6368 2 snd_cs4232,snd_mpu401
snd_seq_midi 5728 0
snd_seq_midi_event 6432 3 snd_seq_virmidi,snd_seq_oss,snd_seq_midi
rfkill 5652 1 rt2x00lib
snd_rawmidi 18496 4 snd_seq_virmidi,snd_emu10k1,snd_mpu401_uart,snd_seq_midi
snd_seq 41456 9 snd_emux_synth,snd_seq_virmidi,snd_seq_midi_emul,snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
led_class 3908 1 rt2x00lib
ns558 3712 0
parport_pc 22500 1
parport 30988 3 ppdev,lp,parport_pc
snd_timer 17800 5 snd_emu10k1,snd_opl3_lib,snd_cs4231_lib,snd_pcm,snd_seq
input_polldev 3752 1 rt2x00lib
mac80211 139776 2 rt2x00pci,rt2x00lib
snd_seq_device 6380 9 snd_emu10k1_synth,snd_emux_synth,snd_emu10k1,snd_opl3_lib,snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
emu10k1_gp 2688 0
snd 45636 21 snd_emux_synth,snd_seq_virmidi,snd_emu10k1,snd_cs4232,snd_ac97_codec,snd_opl3_lib,snd_cs4231_lib,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_mpu401,snd_mpu401_uart,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
cfg80211 21608 2 rt2x00lib,mac80211
gameport 10700 4 ns558,emu10k1_gp
soundcore 6368 1 snd
eeprom_93cx6 2144 1 rt2500pci
serio_raw 4740 0
pcspkr 2432 0
psmouse 32336 0
k8temp 4064 0
shpchp 25528 0
pci_hotplug 23460 1 shpchp
hci_usb 12252 2
bluetooth 44996 9 bnep,sco,rfcomm,l2cap,hci_usb
button 6096 0
i2c_nforce2 5536 0
i2c_core 19828 2 nvidia,i2c_nforce2
evdev 8000 4
ext3 105576 1
jbd 39476 1 ext3
mbcache 7108 1 ext3
dm_mirror 15136 0
dm_log 8452 1 dm_mirror
dm_snapshot 14340 0
dm_mod 46216 3 dm_mirror,dm_log,dm_snapshot
ide_cd_mod 27684 1
cdrom 30176 1 ide_cd_mod
ide_disk 10496 3
usbhid 35904 0
hid 33184 1 usbhid
ff_memless 4392 1 usbhid
ide_pci_generic 3908 0 [permanent]
amd74xx 7752 0 [permanent]
ide_core 96168 4 ide_cd_mod,ide_disk,ide_pci_generic,amd74xx
floppy 47716 0
ohci1394 24976 0
ieee1394 75832 2 sbp2,ohci1394
ata_generic 4676 0
sata_nv 19848 0
libata 140448 2 ata_generic,sata_nv
scsi_mod 129548 2 sbp2,libata
dock 8304 1 libata
forcedeth 45072 0
ehci_hcd 28428 0
ohci_hcd 18532 0
usbcore 118192 5 hci_usb,usbhid,ehci_hcd,ohci_hcd
amd64_agp 8772 1
agpgart 28808 2 nvidia,amd64_agp
thermal 15228 0
processor 32576 2 powernow_k8,thermal
fan 4196 0
thermal_sys 10856 3 thermal,processor,fan
** PCI devices:
00:00.0 Host bridge [0600]: nVidia Corporation nForce3 250Gb Host Bridge [10de:00e1] (rev a1)
Subsystem: ASUSTeK Computer Inc. K8N-E [1043:813f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
Capabilities: <access denied>
Kernel driver in use: agpgart-amd64
Kernel modules: amd64-agp
00:01.0 ISA bridge [0601]: nVidia Corporation nForce3 250Gb LPC Bridge [10de:00e0] (rev a2)
Subsystem: ASUSTeK Computer Inc. K8N-E [1043:813f]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:01.1 SMBus [0c05]: nVidia Corporation nForce 250Gb PCI System Management [10de:00e4] (rev a1)
Subsystem: ASUSTeK Computer Inc. K8N-E [1043:813f]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 0
Region 0: I/O ports at 5080 [size=32]
Region 4: I/O ports at 5000 [size=64]
Region 5: I/O ports at 5040 [size=64]
Capabilities: <access denied>
Kernel driver in use: nForce2_smbus
Kernel modules: i2c-nforce2
00:02.0 USB Controller [0c03]: nVidia Corporation CK8S USB Controller [10de:00e7] (rev a1) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. K8N-E [1043:813f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at febfd000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:02.1 USB Controller [0c03]: nVidia Corporation CK8S USB Controller [10de:00e7] (rev a1) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. K8N-E [1043:813f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 21
Region 0: Memory at febfe000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:02.2 USB Controller [0c03]: nVidia Corporation nForce3 EHCI USB 2.0 Controller [10de:00e8] (rev a2) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. K8N-E [1043:813f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin C routed to IRQ 20
Region 0: Memory at febffc00 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:05.0 Bridge [0680]: nVidia Corporation CK8S Ethernet Controller [10de:00df] (rev a2)
Subsystem: ASUSTeK Computer Inc. K8N-E [1043:80a7]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at febfc000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at ec00 [size=8]
Capabilities: <access denied>
Kernel driver in use: forcedeth
Kernel modules: forcedeth
00:08.0 IDE interface [0101]: nVidia Corporation CK8S Parallel ATA Controller (v2.5) [10de:00e5] (rev a2) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. K8N-E [1043:813f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1]
Region 4: I/O ports at ffa0 [size=16]
Capabilities: <access denied>
Kernel driver in use: AMD_IDE
Kernel modules: amd74xx
00:0a.0 IDE interface [0101]: nVidia Corporation nForce3 Serial ATA Controller [10de:00e3] (rev a2) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. K8N-E [1043:813f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at 09f0 [size=8]
Region 1: I/O ports at 0bf0 [size=4]
Region 2: I/O ports at 0970 [size=8]
Region 3: I/O ports at 0b70 [size=4]
Region 4: I/O ports at c800 [size=16]
Region 5: I/O ports at c400 [size=128]
Capabilities: <access denied>
Kernel driver in use: sata_nv
Kernel modules: sata_nv
00:0b.0 PCI bridge [0604]: nVidia Corporation nForce3 250Gb AGP Host to PCI Bridge [10de:00e2] (rev a2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16
Bus: primary=00, secondary=01, subordinate=01, sec-latency=10
Memory behind bridge: fc900000-fe9fffff
Prefetchable memory behind bridge: cc800000-ec7fffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Kernel modules: shpchp
00:0e.0 PCI bridge [0604]: nVidia Corporation nForce3 250Gb PCI-to-PCI Bridge [10de:00ed] (rev a2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR+ <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=128
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: fea00000-feafffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR+
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Kernel modules: shpchp
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map [1022:1101]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller [1022:1102]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control [1022:1103]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Kernel driver in use: k8temp
Kernel modules: k8temp
01:00.0 VGA compatible controller [0300]: nVidia Corporation NV36.2 [GeForce FX 5700] [10de:0342] (rev a1) (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. Device [1043:8158]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 248 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d0000000 (32-bit, prefetchable) [size=256M]
[virtual] Expansion ROM at fe9e0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: nvidia
Kernel modules: nvidiafb, nvidia
02:07.0 Network controller [0280]: RaLink RT2500 802.11g Cardbus/mini-PCI [1814:0201] (rev 01)
Subsystem: Micro-Star International Co., Ltd. Device [1462:6834]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at feafe000 (32-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: rt2500pci
Kernel modules: rt2500pci
02:08.0 Multimedia audio controller [0401]: Creative Labs SB Audigy [1102:0004] (rev 03)
Subsystem: Creative Labs SB0090 Audigy Player/OEM [1102:0053]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at b800 [size=32]
Capabilities: <access denied>
Kernel driver in use: EMU10K1_Audigy
Kernel modules: snd-emu10k1
02:08.1 Input device controller [0980]: Creative Labs SB Audigy Game Port [1102:7003] (rev 03)
Subsystem: Creative Labs SB Audigy MIDI/Game Port [1102:0040]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Region 0: I/O ports at bc00 [size=8]
Capabilities: <access denied>
Kernel driver in use: Emu10k1_gameport
Kernel modules: emu10k1-gp
02:08.2 FireWire (IEEE 1394) [0c00]: Creative Labs SB Audigy FireWire Port [1102:4001] (prog-if 10 [OHCI])
Subsystem: Creative Labs SB Audigy FireWire Port [1102:0010]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (500ns min, 1000ns max), Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 19
Region 0: Memory at feafd800 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at feaf8000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: ohci1394
Kernel modules: ohci1394
-- System Information:
Debian Release: 5.0.3
APT prefers stable
APT policy: (900, 'stable')
Architecture: i386 (i686)
Kernel: Linux 2.6.26-2-686 (SMP w/1 CPU core)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.26-2-686 depends on:
ii debconf [debconf-2.0] 1.5.24 Debian configuration management sy
ii initramfs-tools [linux-in 0.93.2~bpo50+2 tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.26-2-686 recommends:
ii libc6-i686 2.7-18 GNU C Library: Shared libraries [i
Versions of packages linux-image-2.6.26-2-686 suggests:
ii grub 0.97-47lenny2 GRand Unified Bootloader (Legacy v
pn linux-doc-2.6.26 <none> (no description available)
-- debconf information:
linux-image-2.6.26-2-686/postinst/bootloader-error-2.6.26-2-686:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.26-2-686/postinst/old-dir-initrd-link-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/overwriting-modules-2.6.26-2-686: true
linux-image-2.6.26-2-686/postinst/bootloader-test-error-2.6.26-2-686:
linux-image-2.6.26-2-686/postinst/depmod-error-2.6.26-2-686: false
linux-image-2.6.26-2-686/preinst/bootloader-initrd-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/abort-overwrite-2.6.26-2-686:
linux-image-2.6.26-2-686/preinst/abort-install-2.6.26-2-686:
linux-image-2.6.26-2-686/postinst/depmod-error-initrd-2.6.26-2-686: false
linux-image-2.6.26-2-686/postinst/create-kimage-link-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/failed-to-move-modules-2.6.26-2-686:
linux-image-2.6.26-2-686/preinst/initrd-2.6.26-2-686:
linux-image-2.6.26-2-686/preinst/lilo-has-ramdisk:
linux-image-2.6.26-2-686/prerm/would-invalidate-boot-loader-2.6.26-2-686: true
linux-image-2.6.26-2-686/postinst/kimage-is-a-directory:
linux-image-2.6.26-2-686/postinst/old-initrd-link-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/elilo-initrd-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/lilo-initrd-2.6.26-2-686: true
linux-image-2.6.26-2-686/prerm/removing-running-kernel-2.6.26-2-686: true
linux-image-2.6.26-2-686/postinst/old-system-map-link-2.6.26-2-686: true
Reply to: