Bug#506223: I can confirm that
On Fri, Aug 21, 2009 at 06:50:13PM +0200, Moritz Muehlenhoff wrote:
> On Thu, Feb 19, 2009 at 09:10:47PM +0000, Marcin Owsiany wrote:
> > I just wiped my etch installation and replaced it with a fresh lenny
> > installation. The installer auto-detected my wifi card and used the
> > rt2500pci driver.
> >
> > By default it achieves:
> > - 1Mbps rate (as reported by iwconfig - I can only download at max.
> > ~20KBps)
> > - approx "50% link quality"
> >
> > When I manually set it to "rate 11M", the reported bit rate goes to 11M,
> > the real download speed improves by about 50% and the "link quality"
> > goes to about 70%, but it's still a far cry from what the card can
> > achieve.
> >
> > It works just fine using ndiswrapper...
>
> Has this been fixed in later kernels like the 2.6.30 from unstable or
> backports.org? There have been many changes since the Lenny kernel.
It seems that in sid the driver does not work at all in WPA mode. Here's
the story:
I tried looking for a Debian live CD featuring sid/squeeze kernel, but
could not find one (live.debian.net seems to only have lenny 5.0.2
images).
So I downloaded a usb stick debian-installer image together with a
netinst iso image and booted off that. After a lot of retries [1] I
managed to get it to a stage where it has detected the network hardware
(identifying it as XXXXXXXXXXXXX), but is not able to configure WPA
(only WEP seems to be supported by d-i). So after some more retries I
copied wpa_* programs together with their required libraries onto the
loaded ramdisk using the usb stick.
Then I tried configuring the network with the following command:
/wpa_supplicant -Dwext -iwlan0 -c/wpa.conf
and the configuration in /wpa.conf (based on the config file which works
for me on the same machine in lenny (though with the NDIS driver)):
| ap_scan=1
| fast_reauth=1
| network={
| priority=100
| ssid="ZyXEL-MnM"
| scan_ssid=1
| key_mgmt=WPA-PSK
| psk="My-passphrase"
| }
However it seems the connection cannot be established. What I get is
(retyped manually from the screen, so there may be some typos):
Trying to associate with XX:XX:XX:XX:XX:XX (SSID='ZyXEL-MnM' freq=2437 MHz)
Association request to the driver failed
Associated with XX:XX:XX:XX:XX:XX
ioctl[SIOCSIWENCODEEXT]: Cannot allocate memory
WPA: Failed to set PTK to the driver
WPA: Key negotiation completed with XX:XX:XX:XX:XX:XX [PTK=CCMP GTK=TKIP]
CTRL-EVENT-CONNECTED - Connection to XX:XX:XX:XX:XX:XX completed (auth) [id_str=]
CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys
ioctl[SIOCSIWENCODEEXT]: No such file or directory
Associated with XX:XX:XX:XX:XX:XX
CTRL-EVENT-SCAN-RESULTS
ioctl[SIOCSIWENCODEEXT]: Cannot allocate memory
WPA: Failed to set PTK to the driver
WPA: Key negotiation completed with XX:XX:XX:XX:XX:XX [PTK=CCMP GTK=TKIP]
CTRL-EVENT-CONNECTED - Connection to XX:XX:XX:XX:XX:XX completed (reauth) [id_str=]
CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys
ioctl[SIOCSIWENCODEEXT]: No such file or directory
Associated with XX:XX:XX:XX:XX:XX
CTRL-EVENT-SCAN-RESULTS
[... and so on...]
Here's some more, retrieved from the same command with "-dd" appended,
running in "script(1)".
Initializing interface 'wlan0' conf '/wpa.conf' driver 'wext' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/wpa.conf' -> '/wpa.conf'
Reading configuration file '/wpa.conf'
ap_scan=1
fast_reauth=1
Line: 3 - start of a new network block
priority=100 (0x64)
ssid - hexdump_ascii(len=9):
5a 79 58 45 4c 2d 4d 6e 4d ZyXEL-MnM
scan_ssid=1 (0x1)
key_mgmt: 0x2
PSK (ASCII passphrase) - hexdump_ascii(len=41): [REMOVED]
PSK (from passphrase) - hexdump(len=32): [REMOVED]
Priority group 100
id=0 ssid='ZyXEL-MnM'
Interface wlan0 set UP - waiting a second for the driver to complete initialization
SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf
capabilities: key_mgmt 0xf enc 0xf flags 0x0
WEXT: Operstate: linkmode=1, operstate=5
Own MAC address: 00:11:50:90:41:9b
wpa_driver_wext_set_wpa
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_countermeasures
wpa_driver_wext_set_drop_unencrypted
RSN: flushing PMKID list in the driver
Setting scan request: 0 sec 100000 usec
WPS: UUID based on MAC address - hexdump(len=16): 88 ef 2a a6 5d a1 5b a7 a8 99 88 1e 34 b0 23 12
WPS: Build Beacon and Probe Response IEs
WPS: * Version
WPS: * Wi-Fi Protected Setup State (0)
WPS: * Version
WPS: * Wi-Fi Protected Setup State (0)
WPS: * Response Type (2)
WPS: * UUID-E
WPS: * Manufacturer
WPS: * Model Name
WPS: * Model Number
WPS: * Serial Number
WPS: * Primary Device Type
WPS: * Device Name
WPS: * Config Methods (0)
WPS: * RF Bands (3)
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
Added interface wlan0
Ignore event for foreign ifindex 2
RTM_NEWLINK: operstate=0 ifi_flags=0x1043 ([UP][RUNNING])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b06 len=8
State: DISCONNECTED -> SCANNING
Starting AP scan (specific SSID)
Scan SSID - hexdump_ascii(len=9):
5a 79 58 45 4c 2d 4d 6e 4d ZyXEL-MnM
Trying to get current scan results first without requesting a new scan to speed up initial association
Received 351 bytes of scan results (1 BSSes)
CTRL-EVENT-SCAN-RESULTS
Selecting BSS from priority group 100
Try to find WPA-enabled AP
0: 00:02:cf:6a:32:c8 ssid='ZyXEL-MnM' wpa_ie_len=22 rsn_ie_len=20 caps=0x11
selected based on RSN IE
selected WPA AP 00:02:cf:6a:32:c8 ssid='ZyXEL-MnM'
Trying to associate with 00:02:cf:6a:32:c8 (SSID='ZyXEL-MnM' freq=2437 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
RSN: using IEEE 802.11i/D9.0
WPA: Selected cipher suites: group 8 pairwise 16 key_mgmt 2 proto 2
WPA: set AP WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
WPA: set AP RSN IE - hexdump(len=22): 30 14 01 00 00 0f ac 02 01 00 00 0f ac 04 01 00 00 0f ac 02 01 00
WPA: using GTK TKIP
WPA: using PTK CCMP
WPA: using KEY_MGMT WPA-PSK
WPA: not using MGMT group cipher
WPA: Set own WPA IE default - hexdump(len=22): 30 14 01 00 00 0f ac 02 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
No keys have been configured - skip key clearing
wpa_driver_wext_set_drop_unencrypted
State: SCANNING -> ASSOCIATING
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
wpa_driver_wext_associate
wpa_driver_wext_set_psk
Association request to the driver failed
Setting authentication timeout: 5 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
RSN: added PMKSA cache candidate 00:02:cf:6a:32:c8 prio 1000
RSN: processing PMKSA candidate list
RSN: not in suitable state for new pre-authentication
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b04 len=12
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8c02 len=165
WEXT: Custom wireless event: 'ASSOCINFO(ReqIEs=00095a7958454c2d4d6e4d010802040b160c12182432043048606c30140100000fac020100000fac040100000fac020000 RespIEs=010882848b960c12182432043048606c)'
Association info event
req_ies - hexdump(len=49): 00 09 5a 79 58 45 4c 2d 4d 6e 4d 01 08 02 04 0b 16 0c 12 18 24 32 04 30 48 60 6c 30 14 01 00 00 0f ac 02 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
resp_ies - hexdump(len=16): 01 08 82 84 8b 96 0c 12 18 24 32 04 30 48 60 6c
WPA: set own WPA/RSN IE - hexdump(len=22): 30 14 01 00 00 0f ac 02 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:02:cf:6a:32:c8
State: ASSOCIATING -> ASSOCIATED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
Associated to a new BSS: BSSID=00:02:cf:6a:32:c8
No keys have been configured - skip key clearing
Associated with 00:02:cf:6a:32:c8
WPA: Association event - clear replay counter
WPA: Clear old PTK
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: SUPP_BE entering state IDLE
Setting authentication timeout: 10 sec 0 usec
Cancelling scan request
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
EAPOL: startWhen --> 0
EAPOL: disable timer tick
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: enable timer tick
EAPOL: txStart
WPA: drop TX EAPOL in non-IEEE 802.1X mode (type=1 len=0)
RX EAPOL from 00:02:cf:6a:32:c8
RX EAPOL - hexdump(len=99): 01 03 00 5f 02 00 8a 00 10 00 00 00 00 00 00 00 01 a7 5d b8 6f dc 6b 9a 0a 96 35 fa 9d d3 62 b2 ba cf 9b 05 66 7a 44 47 c4 24 1c 45 65 58 78 8c a7 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Setting authentication timeout: 10 sec 0 usec
IEEE 802.1X RX: version=1 type=3 length=95
EAPOL-Key type=2
key_info 0x8a (ver=2 keyidx=0 rsvd=0 Pairwise Ack)
key_length=16 key_data_length=0
replay_counter - hexdump(len=8): 00 00 00 00 00 00 00 01
key_nonce - hexdump(len=32): a7 5d b8 6f dc 6b 9a 0a 96 35 fa 9d d3 62 b2 ba cf 9b 05 66 7a 44 47 c4 24 1c 45 65 58 78 8c a7
key_iv - hexdump(len=16): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
key_rsc - hexdump(len=8): 00 00 00 00 00 00 00 00
key_id (reserved) - hexdump(len=8): 00 00 00 00 00 00 00 00
key_mic - hexdump(len=16): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
WPA: RX EAPOL-Key - hexdump(len=99): 01 03 00 5f 02 00 8a 00 10 00 00 00 00 00 00 00 01 a7 5d b8 6f dc 6b 9a 0a 96 35 fa 9d d3 62 b2 ba cf 9b 05 66 7a 44 47 c4 24 1c 45 65 58 78 8c a7 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
State: ASSOCIATED -> 4WAY_HANDSHAKE
WPA: RX message 1 of 4-Way Handshake from 00:02:cf:6a:32:c8 (ver=2)
RSN: msg 1/4 key data - hexdump(len=0):
WPA: Renewed SNonce - hexdump(len=32): df a9 04 69 8b 8c 79 b0 1a 0d 39 80 61 b9 d9 04 8b f0 b5 0b 41 dc 16 42 3e 5f 6e 4f e9 57 68 b6
WPA: PTK derivation - A1=00:11:50:90:41:9b A2=00:02:cf:6a:32:c8
WPA: PMK - hexdump(len=32): [REMOVED]
WPA: PTK - hexdump(len=64): [REMOVED]
WPA: WPA IE for msg 2/4 - hexdump(len=22): 30 14 01 00 00 0f ac 02 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
WPA: Sending EAPOL-Key 2/4
WPA: TX EAPOL-Key - hexdump(len=121): 01 03 00 75 02 01 0a 00 00 00 00 00 00 00 00 00 01 df a9 04 69 8b 8c 79 b0 1a 0d 39 80 61 b9 d9 04 8b f0 b5 0b 41 dc 16 42 3e 5f 6e 4f e9 57 68 b6 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 95 3b a2 98 5f 73 47 35 7e bf 9f 42 2e 76 22 eb 00 16 30 14 01 00 00 0f ac 02 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
RX EAPOL from 00:02:cf:6a:32:c8
RX EAPOL - hexdump(len=171): 01 03 00 a7 02 13 ca 00 10 00 00 00 00 00 00 00 02 a7 5d b8 6f dc 6b 9a 0a 96 35 fa 9d d3 62 b2 ba cf 9b 05 66 7a 44 47 c4 24 1c 45 65 58 78 8c a7 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f1 21 12 a8 b0 62 23 d7 47 86 ff 1b 34 a3 d0 f1 00 48 49 ad 81 9a ff 65 e6 ef 00 6b 4b 61 f6 c4 1c f6 83 ac e4 35 da 95 9e 8e 11 db 84 dc b2 ea a0 b4 3c 97 b1 5b 2a d9 db 23 7b 96 35 72 95 ae f9 69 2a f0 bb 8f 3a 94 67 05 c0 be a6 93 cd de 7e 0b d9 80 0d df 52 bb 45 ce
IEEE 802.1X RX: version=1 type=3 length=167
EAPOL-Key type=2
key_info 0x13ca (ver=2 keyidx=0 rsvd=0 Pairwise Install Ack MIC Secure Encr)
key_length=16 key_data_length=72
replay_counter - hexdump(len=8): 00 00 00 00 00 00 00 02
key_nonce - hexdump(len=32): a7 5d b8 6f dc 6b 9a 0a 96 35 fa 9d d3 62 b2 ba cf 9b 05 66 7a 44 47 c4 24 1c 45 65 58 78 8c a7
key_iv - hexdump(len=16): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
key_rsc - hexdump(len=8): 00 00 00 00 00 00 00 00
key_id (reserved) - hexdump(len=8): 00 00 00 00 00 00 00 00
key_mic - hexdump(len=16): f1 21 12 a8 b0 62 23 d7 47 86 ff 1b 34 a3 d0 f1
WPA: RX EAPOL-Key - hexdump(len=171): 01 03 00 a7 02 13 ca 00 10 00 00 00 00 00 00 00 02 a7 5d b8 6f dc 6b 9a 0a 96 35 fa 9d d3 62 b2 ba cf 9b 05 66 7a 44 47 c4 24 1c 45 65 58 78 8c a7 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f1 21 12 a8 b0 62 23 d7 47 86 ff 1b 34 a3 d0 f1 00 48 49 ad 81 9a ff 65 e6 ef 00 6b 4b 61 f6 c4 1c f6 83 ac e4 35 da 95 9e 8e 11 db 84 dc b2 ea a0 b4 3c 97 b1 5b 2a d9 db 23 7b 96 35 72 95 ae f9 69 2a f0 bb 8f 3a 94 67 05 c0 be a6 93 cd de 7e 0b d9 80 0d df 52 bb 45 ce
RSN: encrypted key data - hexdump(len=72): 49 ad 81 9a ff 65 e6 ef 00 6b 4b 61 f6 c4 1c f6 83 ac e4 35 da 95 9e 8e 11 db 84 dc b2 ea a0 b4 3c 97 b1 5b 2a d9 db 23 7b 96 35 72 95 ae f9 69 2a f0 bb 8f 3a 94 67 05 c0 be a6 93 cd de 7e 0b d9 80 0d df 52 bb 45 ce
WPA: decrypted EAPOL-Key key data - hexdump(len=64): [REMOVED]
State: 4WAY_HANDSHAKE -> 4WAY_HANDSHAKE
WPA: RX message 3 of 4-Way Handshake from 00:02:cf:6a:32:c8 (ver=2)
WPA: IE KeyData - hexdump(len=64): 30 14 01 00 00 0f ac 02 01 00 00 0f ac 04 01 00 00 0f ac 02 01 00 dd 26 00 0f ac 01 01 00 2c b0 71 b1 b4 3d 15 11 5e 69 ca 65 8d 8f 91 f0 73 c1 d7 25 e0 24 58 e9 44 c2 f3 c0 c9 30 79 5c dd 00
WPA: Sending EAPOL-Key 4/4
WPA: TX EAPOL-Key - hexdump(len=99): 01 03 00 5f 02 03 0a 00 00 00 00 00 00 00 00 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 de 32 41 70 ef ea 9e 2f ce 1c ef b5 48 52 32 f8 00 00
WPA: Installing PTK to the driver.
wpa_driver_wext_set_key: alg=3 key_idx=0 set_tx=1 seq_len=6 key_len=16
ioctl[SIOCSIWENCODEEXT]: Cannot allocate memory
Driver did not support SIOCSIWENCODEEXT
WPA: Failed to set PTK to the driver.
EAPOL: External notification - portValid=1
State: 4WAY_HANDSHAKE -> GROUP_HANDSHAKE
RSN: received GTK in pairwise handshake - hexdump(len=34): [REMOVED]
WPA: Group Key - hexdump(len=32): [REMOVED]
WPA: Installing GTK to the driver (keyidx=1 tx=0 len=32).
WPA: RSC - hexdump(len=6): 00 00 00 00 00 00
wpa_driver_wext_set_key: alg=2 key_idx=1 set_tx=0 seq_len=6 key_len=32
WPA: Key negotiation completed with 00:02:cf:6a:32:c8 [PTK=CCMP GTK=TKIP]
Cancelling authentication timeout
State: GROUP_HANDSHAKE -> COMPLETED
CTRL-EVENT-CONNECTED - Connection to 00:02:cf:6a:32:c8 completed (auth) [id=0 id_str=]
wpa_driver_wext_set_operstate: operstate 0->1 (UP)
WEXT: Operstate: linkmode=-1, operstate=6
EAPOL: External notification - portValid=1
EAPOL: External notification - EAP success=1
EAPOL: SUPP_PAE entering state AUTHENTICATING
EAPOL: SUPP_BE entering state SUCCESS
EAP: EAP entering state DISABLED
EAPOL: SUPP_PAE entering state AUTHENTICATED
EAPOL: SUPP_BE entering state IDLE
EAPOL authentication completed successfully
RTM_NEWLINK: operstate=1 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
RSN: processing PMKSA candidate list
RSN: not in suitable state for new pre-authentication
RTM_NEWLINK: operstate=1 ifi_flags=0x1043 ([UP][RUNNING])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:00:00:00:00:00
Setting scan request: 0 sec 100000 usec
Added BSSID 00:02:cf:6a:32:c8 into blacklist
CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
ioctl[SIOCSIWENCODEEXT]: No such file or directory
Driver did not support SIOCSIWENCODEEXT
State: COMPLETED -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 1->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
EAPOL: External notification - portEnabled=0
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: SUPP_BE entering state INITIALIZE
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
State: DISCONNECTED -> SCANNING
Starting AP scan (broadcast SSID)
Scan requested (ret=0) - scan timeout 5 seconds
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8c02 len=165
WEXT: Custom wireless event: 'ASSOCINFO(ReqIEs=00095a7958454c2d4d6e4d010802040b160c12182432043048606c30140100000fac020100000fac040100000fac020000 RespIEs=010882848b960c12182432043048606c)'
Association info event
req_ies - hexdump(len=49): 00 09 5a 79 58 45 4c 2d 4d 6e 4d 01 08 02 04 0b 16 0c 12 18 24 32 04 30 48 60 6c 30 14 01 00 00 0f ac 02 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
resp_ies - hexdump(len=16): 01 08 82 84 8b 96 0c 12 18 24 32 04 30 48 60 6c
WPA: set own WPA/RSN IE - hexdump(len=22): 30 14 01 00 00 0f ac 02 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:02:cf:6a:32:c8
State: SCANNING -> ASSOCIATED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
Associated to a new BSS: BSSID=00:02:cf:6a:32:c8
No keys have been configured - skip key clearing
Associated with 00:02:cf:6a:32:c8
WPA: Association event - clear replay counter
WPA: Clear old PTK
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: SUPP_BE entering state IDLE
Setting authentication timeout: 10 sec 0 usec
Cancelling scan request
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
EAPOL: startWhen --> 0
EAPOL: disable timer tick
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: enable timer tick
EAPOL: txStart
WPA: drop TX EAPOL in non-IEEE 802.1X mode (type=1 len=0)
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b19 len=8
Received 698 bytes of scan results (2 BSSes)
CTRL-EVENT-SCAN-RESULTS
Selecting BSS from priority group 100
Try to find WPA-enabled AP
0: 00:02:cf:6a:32:c8 ssid='ZyXEL-MnM' wpa_ie_len=22 rsn_ie_len=20 caps=0x11
selected based on RSN IE
selected WPA AP 00:02:cf:6a:32:c8 ssid='ZyXEL-MnM'
Already associated with the selected AP.
RX EAPOL from 00:02:cf:6a:32:c8
RX EAPOL - hexdump(len=99): 01 03 00 5f 02 00 8a 00 10 00 00 00 00 00 00 00 01 55 67 e9 3c c6 b3 ff f7 2a c0 41 57 77 17 b8 e7 c0 4c 94 ce 74 67 91 5d d6 d8 8d 27 94 49 29 bd 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Setting authentication timeout: 10 sec 0 usec
IEEE 802.1X RX: version=1 type=3 length=95
EAPOL-Key type=2
key_info 0x8a (ver=2 keyidx=0 rsvd=0 Pairwise Ack)
key_length=16 key_data_length=0
replay_counter - hexdump(len=8): 00 00 00 00 00 00 00 01
key_nonce - hexdump(len=32): 55 67 e9 3c c6 b3 ff f7 2a c0 41 57 77 17 b8 e7 c0 4c 94 ce 74 67 91 5d d6 d8 8d 27 94 49 29 bd
key_iv - hexdump(len=16): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
key_rsc - hexdump(len=8): 00 00 00 00 00 00 00 00
key_id (reserved) - hexdump(len=8): 00 00 00 00 00 00 00 00
key_mic - hexdump(len=16): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
WPA: RX EAPOL-Key - hexdump(len=99): 01 03 00 5f 02 00 8a 00 10 00 00 00 00 00 00 00 01 55 67 e9 3c c6 b3 ff f7 2a c0 41 57 77 17 b8 e7 c0 4c 94 ce 74 67 91 5d d6 d8 8d 27 94 49 29 bd 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
State: ASSOCIATED -> 4WAY_HANDSHAKE
WPA: RX message 1 of 4-Way Handshake from 00:02:cf:6a:32:c8 (ver=2)
RSN: msg 1/4 key data - hexdump(len=0):
WPA: Renewed SNonce - hexdump(len=32): aa e6 22 9d 8a ac b6 99 47 35 d3 ee 07 81 b9 34 2e e1 30 44 6e 68 ba 0e 60 83 46 a9 38 27 8c 09
WPA: PTK derivation - A1=00:11:50:90:41:9b A2=00:02:cf:6a:32:c8
WPA: PMK - hexdump(len=32): [REMOVED]
WPA: PTK - hexdump(len=64): [REMOVED]
WPA: WPA IE for msg 2/4 - hexdump(len=22): 30 14 01 00 00 0f ac 02 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
WPA: Sending EAPOL-Key 2/4
WPA: TX EAPOL-Key - hexdump(len=121): 01 03 00 75 02 01 0a 00 00 00 00 00 00 00 00 00 01 aa e6 22 9d 8a ac b6 99 47 35 d3 ee 07 81 b9 34 2e e1 30 44 6e 68 ba 0e 60 83 46 a9 38 27 8c 09 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 83 08 a2 82 1c cf e9 1d 24 30 59 d9 52 a7 10 25 00 16 30 14 01 00 00 0f ac 02 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
RX EAPOL from 00:02:cf:6a:32:c8
RX EAPOL - hexdump(len=171): 01 03 00 a7 02 13 ca 00 10 00 00 00 00 00 00 00 02 55 67 e9 3c c6 b3 ff f7 2a c0 41 57 77 17 b8 e7 c0 4c 94 ce 74 67 91 5d d6 d8 8d 27 94 49 29 bd 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f7 f6 d4 0a c0 45 ae 9a 01 fd 73 c1 6c d5 4e 90 00 48 a4 e5 90 6d fc 7f 11 b0 52 c2 90 ef ff 39 58 0e f7 c6 b2 3a c7 53 7e 1b 05 97 d4 98 5d 69 08 d6 fb 99 f7 54 b2 ae ae 51 5c a8 0d 1c 01 84 c1 4e 9d 8c 66 e4 3c ac 96 fb e4 3f dc e4 d1 59 30 8c 47 1f c3 0c 8a a5 49 13
IEEE 802.1X RX: version=1 type=3 length=167
EAPOL-Key type=2
key_info 0x13ca (ver=2 keyidx=0 rsvd=0 Pairwise Install Ack MIC Secure Encr)
key_length=16 key_data_length=72
replay_counter - hexdump(len=8): 00 00 00 00 00 00 00 02
key_nonce - hexdump(len=32): 55 67 e9 3c c6 b3 ff f7 2a c0 41 57 77 17 b8 e7 c0 4c 94 ce 74 67 91 5d d6 d8 8d 27 94 49 29 bd
key_iv - hexdump(len=16): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
key_rsc - hexdump(len=8): 00 00 00 00 00 00 00 00
key_id (reserved) - hexdump(len=8): 00 00 00 00 00 00 00 00
key_mic - hexdump(len=16): f7 f6 d4 0a c0 45 ae 9a 01 fd 73 c1 6c d5 4e 90
WPA: RX EAPOL-Key - hexdump(len=171): 01 03 00 a7 02 13 ca 00 10 00 00 00 00 00 00 00 02 55 67 e9 3c c6 b3 ff f7 2a c0 41 57 77 17 b8 e7 c0 4c 94 ce 74 67 91 5d d6 d8 8d 27 94 49 29 bd 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f7 f6 d4 0a c0 45 ae 9a 01 fd 73 c1 6c d5 4e 90 00 48 a4 e5 90 6d fc 7f 11 b0 52 c2 90 ef ff 39 58 0e f7 c6 b2 3a c7 53 7e 1b 05 97 d4 98 5d 69 08 d6 fb 99 f7 54 b2 ae ae 51 5c a8 0d 1c 01 84 c1 4e 9d 8c 66 e4 3c ac 96 fb e4 3f dc e4 d1 59 30 8c 47 1f c3 0c 8a a5 49 13
RSN: encrypted key data - hexdump(len=72): a4 e5 90 6d fc 7f 11 b0 52 c2 90 ef ff 39 58 0e f7 c6 b2 3a c7 53 7e 1b 05 97 d4 98 5d 69 08 d6 fb 99 f7 54 b2 ae ae 51 5c a8 0d 1c 01 84 c1 4e 9d 8c 66 e4 3c ac 96 fb e4 3f dc e4 d1 59 30 8c 47 1f c3 0c 8a a5 49 13
WPA: decrypted EAPOL-Key key data - hexdump(len=64): [REMOVED]
State: 4WAY_HANDSHAKE -> 4WAY_HANDSHAKE
WPA: RX message 3 of 4-Way Handshake from 00:02:cf:6a:32:c8 (ver=2)
WPA: IE KeyData - hexdump(len=64): 30 14 01 00 00 0f ac 02 01 00 00 0f ac 04 01 00 00 0f ac 02 01 00 dd 26 00 0f ac 01 01 00 3f 5d 83 79 c5 17 d4 f2 f7 2e a0 af f4 9d 14 94 e6 d5 d4 21 11 dc d5 00 af 9b eb e7 0a 45 70 40 dd 00
WPA: Sending EAPOL-Key 4/4
WPA: TX EAPOL-Key - hexdump(len=99): 01 03 00 5f 02 03 0a 00 00 00 00 00 00 00 00 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 77 65 dc 29 24 1d 20 fb 20 af 88 cf 23 96 87 49 00 00
WPA: Installing PTK to the driver.
wpa_driver_wext_set_key: alg=3 key_idx=0 set_tx=1 seq_len=6 key_len=16
ioctl[SIOCSIWENCODEEXT]: Cannot allocate memory
Driver did not support SIOCSIWENCODEEXT
WPA: Failed to set PTK to the driver.
EAPOL: External notification - portValid=1
State: 4WAY_HANDSHAKE -> GROUP_HANDSHAKE
RSN: received GTK in pairwise handshake - hexdump(len=34): [REMOVED]
WPA: Group Key - hexdump(len=32): [REMOVED]
WPA: Installing GTK to the driver (keyidx=1 tx=0 len=32).
WPA: RSC - hexdump(len=6): 00 00 00 00 00 00
wpa_driver_wext_set_key: alg=2 key_idx=1 set_tx=0 seq_len=6 key_len=32
WPA: Key negotiation completed with 00:02:cf:6a:32:c8 [PTK=CCMP GTK=TKIP]
Cancelling authentication timeout
Removed BSSID 00:02:cf:6a:32:c8 from blacklist
State: GROUP_HANDSHAKE -> COMPLETED
CTRL-EVENT-CONNECTED - Connection to 00:02:cf:6a:32:c8 completed (reauth) [id=0 id_str=]
wpa_driver_wext_set_operstate: operstate 0->1 (UP)
WEXT: Operstate: linkmode=-1, operstate=6
EAPOL: External notification - portValid=1
EAPOL: External notification - EAP success=1
EAPOL: SUPP_PAE entering state AUTHENTICATING
EAPOL: SUPP_BE entering state SUCCESS
EAP: EAP entering state DISABLED
EAPOL: SUPP_PAE entering state AUTHENTICATED
EAPOL: SUPP_BE entering state IDLE
EAPOL authentication completed successfully
RTM_NEWLINK: operstate=1 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
RTM_NEWLINK: operstate=1 ifi_flags=0x1043 ([UP][RUNNING])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:00:00:00:00:00
Setting scan request: 0 sec 100000 usec
Added BSSID 00:02:cf:6a:32:c8 into blacklist
CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
ioctl[SIOCSIWENCODEEXT]: No such file or directory
Driver did not support SIOCSIWENCODEEXT
State: COMPLETED -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 1->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
EAPOL: External notification - portEnabled=0
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: SUPP_BE entering state INITIALIZE
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
State: DISCONNECTED -> SCANNING
Hopefully someone will be able to figure out what's going on here.
I'm willing to do some more debugging.
/proc/version:
---------------------------------------
Linux version 2.6.30-2-486 (Debian 2.6.30-7) (waldi@debian.org) (gcc version 4.3.4 (Debian 4.3.4-2) ) #1 Wed Sep 16 16:57:24 UTC 2009
lsmod:
---------------------------------------
Module Size Used by
firewire_sbp2 12852 0
arc4 1564 2
ecb 2368 2
rt2500pci 13948 0
rt2x00pci 7212 1 rt2500pci
rt2x00lib 25840 2 rt2500pci,rt2x00pci
led_class 3780 1 rt2x00lib
input_polldev 3580 1 rt2x00lib
mac80211 141416 2 rt2x00pci,rt2x00lib
firewire_ohci 19008 0
cfg80211 54996 2 rt2x00lib,mac80211
eeprom_93cx6 1920 1 rt2500pci
b44 21760 0
ssb 37768 1 b44
mii 4620 1 b44
firewire_core 37676 2 firewire_sbp2,firewire_ohci
crc_itu_t 2148 1 firewire_core
nls_utf8 1416 3
nls_cp437 5244 2
loop 12960 2
isofs 27040 1
vfat 8492 2
fat 40856 1 vfat
nls_base 6136 5 nls_utf8,nls_cp437,isofs,vfat,fat
reiserfs 183856 0
ext3 104552 0
jbd 36548 1 ext3
ext2 52072 0
mbcache 6496 2 ext3,ext2
ide_generic 1744 0 [permanent]
sd_mod 28552 2
crc_t10dif 1556 1 sd_mod
vga16fb 9156 2
vgastate 6576 1 vga16fb
ide_cd_mod 24340 0
ide_gd_mod 19576 0
cdrom 30280 1 ide_cd_mod
usb_storage 48088 2
scsi_mod 131732 3 firewire_sbp2,sd_mod,usb_storage
pcmcia 23052 1 ssb
fan 3984 0
uhci_hcd 18796 0
piix 5568 0
ehci_hcd 29604 0
yenta_socket 21012 2
rsrc_nonstatic 9580 1 yenta_socket
pcmcia_core 30924 4 ssb,pcmcia,yenta_socket,rsrc_nonstatic
ide_core 87080 4 ide_generic,ide_cd_mod,ide_gd_mod,piix
usbcore 124992 4 usb_storage,uhci_hcd,ehci_hcd
thermal 12480 0
thermal_sys 13004 2 fan,thermal
lspci:
---------------------------------------
00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 03)
Subsystem: Hewlett-Packard Company Device 099c
Flags: bus master, fast devsel, latency 0
Capabilities: [e0] Vendor Specific Information <?>
00:02.0 VGA compatible controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03)
Subsystem: Hewlett-Packard Company Device 099c
Flags: fast devsel, IRQ 11
Memory at d0400000 (32-bit, non-prefetchable) [size=512K]
I/O ports at 7000 [size=8]
Memory at c0000000 (32-bit, prefetchable) [size=256M]
Memory at d0480000 (32-bit, non-prefetchable) [size=256K]
Expansion ROM at <unassigned> [disabled]
Capabilities: [d0] Power Management version 2
00:02.1 Display controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03)
Subsystem: Hewlett-Packard Company Device 099c
Flags: bus master, fast devsel, latency 0
Memory at d0500000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [d0] Power Management version 2
00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 03)
Subsystem: Hewlett-Packard Company Device 099c
Flags: bus master, medium devsel, latency 0, IRQ 23
I/O ports at 2000 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 03)
Subsystem: Hewlett-Packard Company Device 099c
Flags: bus master, medium devsel, latency 0, IRQ 17
I/O ports at 2020 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 03)
Subsystem: Hewlett-Packard Company Device 099c
Flags: bus master, medium devsel, latency 0, IRQ 18
I/O ports at 2040 [size=32]
Kernel driver in use: uhci_hcd
00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 03)
Subsystem: Hewlett-Packard Company Device 099c
Flags: bus master, medium devsel, latency 0, IRQ 19
I/O ports at 2060 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 03) (prog-if 20)
Subsystem: Hewlett-Packard Company Device 099c
Flags: bus master, medium devsel, latency 0, IRQ 23
Memory at d0580000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Capabilities: [58] Debug port: BAR=1 offset=00a0
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d3) (prog-if 01)
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=02, subordinate=06, sec-latency=32
I/O behind bridge: 00003000-00003fff
Memory behind bridge: d0000000-d03fffff
Prefetchable memory behind bridge: 0000000040000000-0000000043ffffff
Capabilities: [50] Subsystem: Hewlett-Packard Company Device 099c
00:1e.2 Multimedia audio controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Audio Controller (rev 03)
Subsystem: Hewlett-Packard Company Device 099c
Flags: bus master, medium devsel, latency 0, IRQ 11
I/O ports at 2100 [size=256]
I/O ports at 2200 [size=64]
Memory at d0581000 (32-bit, non-prefetchable) [size=512]
Memory at d0582000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
00:1e.3 Modem: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Modem Controller (rev 03)
Subsystem: Hewlett-Packard Company Device 099c
Flags: medium devsel, IRQ 22
I/O ports at 2400 [size=256]
I/O ports at 2500 [size=128]
Capabilities: [50] Power Management version 2
00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge (rev 03)
Subsystem: Hewlett-Packard Company Device 099c
Flags: bus master, medium devsel, latency 0
00:1f.1 IDE interface: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller (rev 03) (prog-if 8a [Master SecP PriP])
Subsystem: Hewlett-Packard Company Device 099c
Flags: bus master, medium devsel, latency 0, IRQ 16
I/O ports at 01f0 [size=8]
I/O ports at 03f4 [size=1]
I/O ports at 0170 [size=8]
I/O ports at 0374 [size=1]
I/O ports at 2580 [size=16]
Kernel driver in use: PIIX_IDE
02:06.0 CardBus bridge: Texas Instruments PCIxx21/x515 Cardbus Controller
Subsystem: Hewlett-Packard Company Device 099c
Flags: bus master, medium devsel, latency 168, IRQ 18
Memory at d0000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
Memory window 0: 40000000-43fff000 (prefetchable)
Memory window 1: 44000000-47fff000
I/O window 0: 00003000-000030ff
I/O window 1: 00003400-000034ff
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
02:06.2 FireWire (IEEE 1394): Texas Instruments OHCI Compliant IEEE 1394 Host Controller (prog-if 10)
Subsystem: Hewlett-Packard Company Device 099c
Flags: bus master, medium devsel, latency 64, IRQ 22
Memory at d0001000 (32-bit, non-prefetchable) [size=2K]
Memory at d0004000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Kernel driver in use: firewire_ohci
02:06.3 Mass storage controller: Texas Instruments PCIxx21 Integrated FlashMedia Controller
Subsystem: Hewlett-Packard Company Device 099c
Flags: bus master, medium devsel, latency 64, IRQ 10
Memory at d0008000 (32-bit, non-prefetchable) [size=8K]
Capabilities: [44] Power Management version 2
02:06.4 SD Host controller: Texas Instruments PCI6411/6421/6611/6621/7411/7421/7611/7621 Secure Digital Controller
Subsystem: Hewlett-Packard Company Device 099c
Flags: bus master, medium devsel, latency 64, IRQ 10
Memory at d000a000 (32-bit, non-prefetchable) [size=256]
Memory at d000b000 (32-bit, non-prefetchable) [size=256]
Memory at d000c000 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
02:0e.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02)
Subsystem: Hewlett-Packard Company Device 099c
Flags: bus master, fast devsel, latency 64, IRQ 16
Memory at d000e000 (32-bit, non-prefetchable) [size=8K]
Capabilities: [40] Power Management version 2
Kernel driver in use: b44
03:00.0 Network controller: RaLink RT2500 802.11g Cardbus/mini-PCI (rev 01)
Subsystem: Belkin Device 701a
Flags: bus master, slow devsel, latency 64, IRQ 18
Memory at 44000000 (32-bit, non-prefetchable) [size=8K]
Capabilities: [40] Power Management version 2
Kernel driver in use: rt2500pci
syslog:
---------------------------------------
Oct 11 12:55:52 syslogd started: BusyBox v1.14.2
Oct 11 12:55:52 kernel: klogd started: BusyBox v1.14.2 (Debian 1:1.14.2-2)
Oct 11 12:55:52 kernel: [ 0.000000] Initializing cgroup subsys cpuset
Oct 11 12:55:52 kernel: [ 0.000000] Initializing cgroup subsys cpu
Oct 11 12:55:52 kernel: [ 0.000000] Linux version 2.6.30-2-486 (Debian 2.6.30-7) (waldi@debian.org) (gcc version 4.3.4 (Debian 4.3.4-2) ) #1 Wed Sep 16 16:57:24 UTC 2009
Oct 11 12:55:52 kernel: [ 0.000000] KERNEL supported cpus:
Oct 11 12:55:52 kernel: [ 0.000000] Intel GenuineIntel
Oct 11 12:55:52 kernel: [ 0.000000] AMD AuthenticAMD
Oct 11 12:55:52 kernel: [ 0.000000] NSC Geode by NSC
Oct 11 12:55:52 kernel: [ 0.000000] Cyrix CyrixInstead
Oct 11 12:55:52 kernel: [ 0.000000] Centaur CentaurHauls
Oct 11 12:55:52 kernel: [ 0.000000] Transmeta GenuineTMx86
Oct 11 12:55:52 kernel: [ 0.000000] Transmeta TransmetaCPU
Oct 11 12:55:52 kernel: [ 0.000000] UMC UMC UMC UMC
Oct 11 12:55:52 kernel: [ 0.000000] BIOS-provided physical RAM map:
Oct 11 12:55:52 kernel: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
Oct 11 12:55:52 kernel: [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
Oct 11 12:55:52 kernel: [ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
Oct 11 12:55:52 kernel: [ 0.000000] BIOS-e820: 0000000000100000 - 000000003f7d0000 (usable)
Oct 11 12:55:52 kernel: [ 0.000000] BIOS-e820: 000000003f7d0000 - 000000003f7efc00 (reserved)
Oct 11 12:55:52 kernel: [ 0.000000] BIOS-e820: 000000003f7efc00 - 000000003f7fb000 (ACPI NVS)
Oct 11 12:55:52 kernel: [ 0.000000] BIOS-e820: 000000003f7fb000 - 000000003f800000 (reserved)
Oct 11 12:55:52 kernel: [ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
Oct 11 12:55:52 kernel: [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec02000 (reserved)
Oct 11 12:55:52 kernel: [ 0.000000] BIOS-e820: 00000000fed20000 - 00000000fed9b000 (reserved)
Oct 11 12:55:52 kernel: [ 0.000000] BIOS-e820: 00000000feda0000 - 00000000fedc0000 (reserved)
Oct 11 12:55:52 kernel: [ 0.000000] BIOS-e820: 00000000ffb00000 - 00000000ffc00000 (reserved)
Oct 11 12:55:52 kernel: [ 0.000000] BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
Oct 11 12:55:52 kernel: [ 0.000000] DMI 2.3 present.
Oct 11 12:55:52 kernel: [ 0.000000] last_pfn = 0x3f7d0 max_arch_pfn = 0x100000
Oct 11 12:55:52 kernel: [ 0.000000] MTRR default type: uncachable
Oct 11 12:55:52 kernel: [ 0.000000] MTRR fixed ranges enabled:
Oct 11 12:55:52 kernel: [ 0.000000] 00000-9FFFF write-back
Oct 11 12:55:52 kernel: [ 0.000000] A0000-BFFFF uncachable
Oct 11 12:55:52 kernel: [ 0.000000] C0000-CFFFF write-protect
Oct 11 12:55:52 kernel: [ 0.000000] D0000-EFFFF uncachable
Oct 11 12:55:52 kernel: [ 0.000000] F0000-FFFFF write-protect
Oct 11 12:55:52 kernel: [ 0.000000] MTRR variable ranges enabled:
Oct 11 12:55:52 kernel: [ 0.000000] 0 base 000000000 mask FC0000000 write-back
Oct 11 12:55:52 kernel: [ 0.000000] 1 base 03F800000 mask FFF800000 uncachable
Oct 11 12:55:52 kernel: [ 0.000000] 2 base 0FEDA0000 mask FFFFE0000 uncachable
Oct 11 12:55:52 kernel: [ 0.000000] 3 disabled
Oct 11 12:55:52 kernel: [ 0.000000] 4 disabled
Oct 11 12:55:52 kernel: [ 0.000000] 5 disabled
Oct 11 12:55:52 kernel: [ 0.000000] 6 disabled
Oct 11 12:55:52 kernel: [ 0.000000] 7 disabled
Oct 11 12:55:52 kernel: [ 0.000000] PAT not supported by CPU.
Oct 11 12:55:52 kernel: [ 0.000000] init_memory_mapping: 0000000000000000-00000000377fe000
Oct 11 12:55:52 kernel: [ 0.000000] 0000000000 - 0000400000 page 4k
Oct 11 12:55:52 kernel: [ 0.000000] 0000400000 - 0037400000 page 2M
Oct 11 12:55:52 kernel: [ 0.000000] 0037400000 - 00377fe000 page 4k
Oct 11 12:55:52 kernel: [ 0.000000] kernel direct mapping tables up to 377fe000 @ 7000-c000
Oct 11 12:55:52 kernel: [ 0.000000] RAMDISK: 3f2ba000 - 3f7ceb3c
Oct 11 12:55:52 kernel: [ 0.000000] Allocated new RAMDISK: 004eb000 - 009ffb3c
Oct 11 12:55:52 kernel: [ 0.000000] Move RAMDISK from 000000003f2ba000 - 000000003f7ceb3b to 004eb000 - 009ffb3b
Oct 11 12:55:52 kernel: [ 0.000000] ACPI: RSDP 000fe270 00014 (v00 HP )
Oct 11 12:55:52 kernel: [ 0.000000] ACPI: RSDT 3f7efc84 00030 (v01 HP 099C 21120420 HP 00000001)
Oct 11 12:55:52 kernel: [ 0.000000] ACPI: FACP 3f7efc00 00084 (v02 HP 099C 00000002 HP 00000001)
Oct 11 12:55:52 kernel: [ 0.000000] ACPI: DSDT 3f7efd4c 0775C (v01 HP DAU00 00010000 MSFT 0100000E)
Oct 11 12:55:52 kernel: [ 0.000000] ACPI: FACS 3f7fae80 00040
Oct 11 12:55:52 kernel: [ 0.000000] ACPI: APIC 3f7efcb4 0005A (v01 HP 099C 00000001 HP 00000001)
Oct 11 12:55:52 kernel: [ 0.000000] ACPI: MCFG 3f7efd10 0003C (v01 HP 099C 00000001 HP 00000001)
Oct 11 12:55:52 kernel: [ 0.000000] ACPI: Local APIC address 0xfec01000
Oct 11 12:55:52 kernel: [ 0.000000] 127MB HIGHMEM available.
Oct 11 12:55:52 kernel: [ 0.000000] 887MB LOWMEM available.
Oct 11 12:55:52 kernel: [ 0.000000] mapped low ram: 0 - 377fe000
Oct 11 12:55:52 kernel: [ 0.000000] low ram: 0 - 377fe000
Oct 11 12:55:52 kernel: [ 0.000000] node 0 low ram: 00000000 - 377fe000
Oct 11 12:55:52 kernel: [ 0.000000] node 0 bootmap 00008000 - 0000ef00
Oct 11 12:55:52 kernel: [ 0.000000] (7 early reservations) ==> bootmem [0000000000 - 00377fe000]
Oct 11 12:55:52 kernel: [ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
Oct 11 12:55:52 kernel: [ 0.000000] #1 [0000100000 - 00004e71fc] TEXT DATA BSS ==> [0000100000 - 00004e71fc]
Oct 11 12:55:52 kernel: [ 0.000000] #2 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000]
Oct 11 12:55:52 kernel: [ 0.000000] #3 [00004e8000 - 00004ea0d4] BRK ==> [00004e8000 - 00004ea0d4]
Oct 11 12:55:52 kernel: [ 0.000000] #4 [0000007000 - 0000008000] PGTABLE ==> [0000007000 - 0000008000]
Oct 11 12:55:52 kernel: [ 0.000000] #5 [00004eb000 - 00009ffb3c] NEW RAMDISK ==> [00004eb000 - 00009ffb3c]
Oct 11 12:55:52 kernel: [ 0.000000] #6 [0000008000 - 000000f000] BOOTMAP ==> [0000008000 - 000000f000]
Oct 11 12:55:52 kernel: [ 0.000000] Zone PFN ranges:
Oct 11 12:55:52 kernel: [ 0.000000] DMA 0x00000000 -> 0x00001000
Oct 11 12:55:52 kernel: [ 0.000000] Normal 0x00001000 -> 0x000377fe
Oct 11 12:55:52 kernel: [ 0.000000] HighMem 0x000377fe -> 0x0003f7d0
Oct 11 12:55:52 kernel: [ 0.000000] Movable zone start PFN for each node
Oct 11 12:55:52 kernel: [ 0.000000] early_node_map[2] active PFN ranges
Oct 11 12:55:52 kernel: [ 0.000000] 0: 0x00000000 -> 0x0000009f
Oct 11 12:55:52 kernel: [ 0.000000] 0: 0x00000100 -> 0x0003f7d0
Oct 11 12:55:52 kernel: [ 0.000000] On node 0 totalpages: 259951
Oct 11 12:55:52 kernel: [ 0.000000] free_area_init_node: node 0, pgdat c03f526c, node_mem_map c1000000
Oct 11 12:55:52 kernel: [ 0.000000] DMA zone: 32 pages used for memmap
Oct 11 12:55:52 kernel: [ 0.000000] DMA zone: 0 pages reserved
Oct 11 12:55:52 kernel: [ 0.000000] DMA zone: 3967 pages, LIFO batch:0
Oct 11 12:55:52 kernel: [ 0.000000] Normal zone: 1744 pages used for memmap
Oct 11 12:55:52 kernel: [ 0.000000] Normal zone: 221486 pages, LIFO batch:31
Oct 11 12:55:52 kernel: [ 0.000000] HighMem zone: 256 pages used for memmap
Oct 11 12:55:52 kernel: [ 0.000000] HighMem zone: 32466 pages, LIFO batch:7
Oct 11 12:55:52 kernel: [ 0.000000] Using APIC driver default
Oct 11 12:55:52 kernel: [ 0.000000] ACPI: PM-Timer IO Port: 0x1008
Oct 11 12:55:52 kernel: [ 0.000000] ACPI: Local APIC address 0xfec01000
Oct 11 12:55:52 kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Oct 11 12:55:52 kernel: [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
Oct 11 12:55:52 kernel: [ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
Oct 11 12:55:52 kernel: [ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
Oct 11 12:55:52 kernel: [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
Oct 11 12:55:52 kernel: [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Oct 11 12:55:52 kernel: [ 0.000000] ACPI: IRQ0 used by override.
Oct 11 12:55:52 kernel: [ 0.000000] ACPI: IRQ2 used by override.
Oct 11 12:55:52 kernel: [ 0.000000] ACPI: IRQ9 used by override.
Oct 11 12:55:52 kernel: [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
Oct 11 12:55:52 kernel: [ 0.000000] Using ACPI (MADT) for SMP configuration information
Oct 11 12:55:52 kernel: [ 0.000000] nr_irqs_gsi: 24
Oct 11 12:55:52 kernel: [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
Oct 11 12:55:52 kernel: [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
Oct 11 12:55:52 kernel: [ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
Oct 11 12:55:52 kernel: [ 0.000000] Allocating PCI resources starting at 40000000 (gap: 3f800000:a0800000)
Oct 11 12:55:52 kernel: [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 257919
Oct 11 12:55:52 kernel: [ 0.000000] Kernel command line: priority=low vga=normal initrd=initrd.gz -- BOOT_IMAGE=linux
Oct 11 12:55:52 kernel: [ 0.000000] Enabling fast FPU save and restore... done.
Oct 11 12:55:52 kernel: [ 0.000000] Enabling unmasked SIMD FPU exception support... done.
Oct 11 12:55:52 kernel: [ 0.000000] Initializing CPU#0
Oct 11 12:55:52 kernel: [ 0.000000] NR_IRQS:288
Oct 11 12:55:52 kernel: [ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
Oct 11 12:55:52 kernel: [ 0.000000] Fast TSC calibration using PIT
Oct 11 12:55:52 kernel: [ 0.000000] Detected 1296.758 MHz processor.
Oct 11 12:55:52 kernel: [ 0.004000] Console: colour VGA+ 80x25
Oct 11 12:55:52 kernel: [ 0.004000] console [tty0] enabled
Oct 11 12:55:52 kernel: [ 0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Oct 11 12:55:52 kernel: [ 0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Oct 11 12:55:52 kernel: [ 0.004000] Initializing HighMem for node 0 (000377fe:0003f7d0)
Oct 11 12:55:52 kernel: [ 0.004000] Memory: 1021324k/1040192k available (2077k kernel code, 18168k reserved, 990k data, 412k init, 130888k highmem)
Oct 11 12:55:52 kernel: [ 0.004000] virtual kernel memory layout:
Oct 11 12:55:52 kernel: [ 0.004000] fixmap : 0xfffa8000 - 0xfffff000 ( 348 kB)
Oct 11 12:55:52 kernel: [ 0.004000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
Oct 11 12:55:52 kernel: [ 0.004000] vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
Oct 11 12:55:52 kernel: [ 0.004000] lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
Oct 11 12:55:52 kernel: [ 0.004000] .init : 0xc0402000 - 0xc0469000 ( 412 kB)
Oct 11 12:55:52 kernel: [ 0.004000] .data : 0xc030768b - 0xc03fef28 ( 990 kB)
Oct 11 12:55:52 kernel: [ 0.004000] .text : 0xc0100000 - 0xc030768b (2077 kB)
Oct 11 12:55:52 kernel: [ 0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
Oct 11 12:55:52 kernel: [ 0.004022] Calibrating delay loop (skipped), value calculated using timer frequency.. 2593.51 BogoMIPS (lpj=5187032)
Oct 11 12:55:52 kernel: [ 0.004207] Security Framework initialized
Oct 11 12:55:52 kernel: [ 0.004280] SELinux: Disabled at boot.
Oct 11 12:55:52 kernel: [ 0.004359] Mount-cache hash table entries: 512
Oct 11 12:55:52 kernel: [ 0.004597] Initializing cgroup subsys ns
Oct 11 12:55:52 kernel: [ 0.004670] Initializing cgroup subsys cpuacct
Oct 11 12:55:52 kernel: [ 0.004738] Initializing cgroup subsys devices
Oct 11 12:55:52 kernel: [ 0.004805] Initializing cgroup subsys freezer
Oct 11 12:55:52 kernel: [ 0.004872] Initializing cgroup subsys net_cls
Oct 11 12:55:52 kernel: [ 0.004966] CPU: L1 I cache: 32K, L1 D cache: 32K
Oct 11 12:55:52 kernel: [ 0.005068] CPU: L2 cache: 1024K
Oct 11 12:55:52 kernel: [ 0.005143] CPU: Intel(R) Celeron(R) M processor 1.30GHz stepping 06
Oct 11 12:55:52 kernel: [ 0.005292] Checking 'hlt' instruction... OK.
Oct 11 12:55:52 kernel: [ 0.022456] ACPI: Core revision 20090320
Oct 11 12:55:52 kernel: [ 0.040570] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
Oct 11 12:55:52 kernel: [ 0.084001] net_namespace: 1076 bytes
Oct 11 12:55:52 kernel: [ 0.084001] Booting paravirtualized kernel on bare hardware
Oct 11 12:55:52 kernel: [ 0.084001] regulator: core version 0.5
Oct 11 12:55:52 kernel: [ 0.084001] NET: Registered protocol family 16
Oct 11 12:55:52 kernel: [ 0.084001] EISA bus registered
Oct 11 12:55:52 kernel: [ 0.084001] ACPI: bus type pci registered
Oct 11 12:55:52 kernel: [ 0.084001] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
Oct 11 12:55:52 kernel: [ 0.084001] PCI: MCFG area at e0000000 reserved in E820
Oct 11 12:55:52 kernel: [ 0.084001] PCI: Using MMCONFIG for extended config space
Oct 11 12:55:52 kernel: [ 0.084001] PCI: Using configuration type 1 for base access
Oct 11 12:55:52 kernel: [ 0.084001] bio: create slab <bio-0> at 0
Oct 11 12:55:52 kernel: [ 0.084411] ACPI: EC: Look up EC in DSDT
Oct 11 12:55:52 kernel: [ 0.109778] ACPI: EC: non-query interrupt received, switching to interrupt mode
Oct 11 12:55:52 kernel: [ 0.124286] ACPI: Interpreter enabled
Oct 11 12:55:52 kernel: [ 0.124359] ACPI: (supports S0 S3 S4 S5)
Oct 11 12:55:52 kernel: [ 0.124577] ACPI: Using IOAPIC for interrupt routing
Oct 11 12:55:52 kernel: [ 0.137925] ACPI: EC: GPE = 0x10, I/O: command/status = 0x66, data = 0x62
Oct 11 12:55:52 kernel: [ 0.138000] ACPI: EC: driver started in interrupt mode
Oct 11 12:55:52 kernel: [ 0.138192] ACPI: Power Resource [C1BD] (on)
Oct 11 12:55:52 kernel: [ 0.138391] ACPI: Power Resource [C24F] (off)
Oct 11 12:55:52 kernel: [ 0.138577] ACPI: Power Resource [C250] (off)
Oct 11 12:55:52 kernel: [ 0.138761] ACPI: Power Resource [C251] (off)
Oct 11 12:55:52 kernel: [ 0.138947] ACPI: Power Resource [C252] (off)
Oct 11 12:55:52 kernel: [ 0.139325] ACPI: No dock devices found.
Oct 11 12:55:52 kernel: [ 0.139405] ACPI: PCI Root Bridge [C002] (0000:00)
Oct 11 12:55:52 kernel: [ 0.139601] pci 0000:00:02.0: reg 10 32bit mmio: [0xd0400000-0xd047ffff]
Oct 11 12:55:52 kernel: [ 0.139609] pci 0000:00:02.0: reg 14 io port: [0x7000-0x7007]
Oct 11 12:55:52 kernel: [ 0.139615] pci 0000:00:02.0: reg 18 32bit mmio: [0xc0000000-0xcfffffff]
Oct 11 12:55:52 kernel: [ 0.139622] pci 0000:00:02.0: reg 1c 32bit mmio: [0xd0480000-0xd04bffff]
Oct 11 12:55:52 kernel: [ 0.139660] pci 0000:00:02.1: reg 10 32bit mmio: [0xd0500000-0xd057ffff]
Oct 11 12:55:52 kernel: [ 0.139780] pci 0000:00:1d.0: reg 20 io port: [0x2000-0x201f]
Oct 11 12:55:52 kernel: [ 0.139848] pci 0000:00:1d.1: reg 20 io port: [0x2020-0x203f]
Oct 11 12:55:52 kernel: [ 0.139917] pci 0000:00:1d.2: reg 20 io port: [0x2040-0x205f]
Oct 11 12:55:52 kernel: [ 0.139984] pci 0000:00:1d.3: reg 20 io port: [0x2060-0x207f]
Oct 11 12:55:52 kernel: [ 0.140092] pci 0000:00:1d.7: reg 10 32bit mmio: [0xd0580000-0xd05803ff]
Oct 11 12:55:52 kernel: [ 0.140157] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
Oct 11 12:55:52 kernel: [ 0.140235] pci 0000:00:1d.7: PME# disabled
Oct 11 12:55:52 kernel: [ 0.140410] pci 0000:00:1e.2: reg 10 io port: [0x2100-0x21ff]
Oct 11 12:55:52 kernel: [ 0.140420] pci 0000:00:1e.2: reg 14 io port: [0x2200-0x223f]
Oct 11 12:55:52 kernel: [ 0.140430] pci 0000:00:1e.2: reg 18 32bit mmio: [0xd0581000-0xd05811ff]
Oct 11 12:55:52 kernel: [ 0.140440] pci 0000:00:1e.2: reg 1c 32bit mmio: [0xd0582000-0xd05820ff]
Oct 11 12:55:52 kernel: [ 0.140482] pci 0000:00:1e.2: PME# supported from D0 D3hot D3cold
Oct 11 12:55:52 kernel: [ 0.140557] pci 0000:00:1e.2: PME# disabled
Oct 11 12:55:52 kernel: [ 0.140661] pci 0000:00:1e.3: reg 10 io port: [0x2400-0x24ff]
Oct 11 12:55:52 kernel: [ 0.140671] pci 0000:00:1e.3: reg 14 io port: [0x2500-0x257f]
Oct 11 12:55:52 kernel: [ 0.140723] pci 0000:00:1e.3: PME# supported from D0 D3hot D3cold
Oct 11 12:55:52 kernel: [ 0.140799] pci 0000:00:1e.3: PME# disabled
Oct 11 12:55:52 kernel: [ 0.140958] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
Oct 11 12:55:52 kernel: [ 0.140970] pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
Oct 11 12:55:52 kernel: [ 0.141068] pci 0000:00:1f.0: quirk: region 1100-113f claimed by ICH6 GPIO
Oct 11 12:55:52 kernel: [ 0.141144] pci 0000:00:1f.0: LPC Generic IO decode 1 PIO at 0500-057f
Oct 11 12:55:52 kernel: [ 0.141248] pci 0000:00:1f.1: reg 10 io port: [0x00-0x07]
Oct 11 12:55:52 kernel: [ 0.141257] pci 0000:00:1f.1: reg 14 io port: [0x00-0x03]
Oct 11 12:55:52 kernel: [ 0.141267] pci 0000:00:1f.1: reg 18 io port: [0x00-0x07]
Oct 11 12:55:52 kernel: [ 0.141276] pci 0000:00:1f.1: reg 1c io port: [0x00-0x03]
Oct 11 12:55:52 kernel: [ 0.141286] pci 0000:00:1f.1: reg 20 io port: [0x2580-0x258f]
Oct 11 12:55:52 kernel: [ 0.141380] pci 0000:02:06.0: reg 10 32bit mmio: [0xd0000000-0xd0000fff]
Oct 11 12:55:52 kernel: [ 0.141410] pci 0000:02:06.0: supports D1 D2
Oct 11 12:55:52 kernel: [ 0.141413] pci 0000:02:06.0: PME# supported from D0 D1 D2 D3hot D3cold
Oct 11 12:55:52 kernel: [ 0.141489] pci 0000:02:06.0: PME# disabled
Oct 11 12:55:52 kernel: [ 0.141606] pci 0000:02:06.2: reg 10 32bit mmio: [0xd0001000-0xd00017ff]
Oct 11 12:55:52 kernel: [ 0.141618] pci 0000:02:06.2: reg 14 32bit mmio: [0xd0004000-0xd0007fff]
Oct 11 12:55:52 kernel: [ 0.141687] pci 0000:02:06.2: supports D1 D2
Oct 11 12:55:52 kernel: [ 0.141690] pci 0000:02:06.2: PME# supported from D0 D1 D2 D3hot
Oct 11 12:55:52 kernel: [ 0.141765] pci 0000:02:06.2: PME# disabled
Oct 11 12:55:52 kernel: [ 0.141879] pci 0000:02:06.3: reg 10 32bit mmio: [0xd0008000-0xd0009fff]
Oct 11 12:55:52 kernel: [ 0.141948] pci 0000:02:06.3: supports D1 D2
Oct 11 12:55:52 kernel: [ 0.141951] pci 0000:02:06.3: PME# supported from D0 D1 D2 D3hot
Oct 11 12:55:52 kernel: [ 0.142026] pci 0000:02:06.3: PME# disabled
Oct 11 12:55:52 kernel: [ 0.142138] pci 0000:02:06.4: reg 10 32bit mmio: [0xd000a000-0xd000a0ff]
Oct 11 12:55:52 kernel: [ 0.142150] pci 0000:02:06.4: reg 14 32bit mmio: [0xd000b000-0xd000b0ff]
Oct 11 12:55:52 kernel: [ 0.142161] pci 0000:02:06.4: reg 18 32bit mmio: [0xd000c000-0xd000c0ff]
Oct 11 12:55:52 kernel: [ 0.142217] pci 0000:02:06.4: supports D1 D2
Oct 11 12:55:52 kernel: [ 0.142220] pci 0000:02:06.4: PME# supported from D0 D1 D2 D3hot
Oct 11 12:55:52 kernel: [ 0.142294] pci 0000:02:06.4: PME# disabled
Oct 11 12:55:52 kernel: [ 0.142420] pci 0000:02:0e.0: reg 10 32bit mmio: [0xd000e000-0xd000ffff]
Oct 11 12:55:52 kernel: [ 0.142479] pci 0000:02:0e.0: supports D1 D2
Oct 11 12:55:52 kernel: [ 0.142483] pci 0000:02:0e.0: PME# supported from D0 D1 D2 D3hot D3cold
Oct 11 12:55:52 kernel: [ 0.142559] pci 0000:02:0e.0: PME# disabled
Oct 11 12:55:52 kernel: [ 0.142661] pci 0000:00:1e.0: transparent bridge
Oct 11 12:55:52 kernel: [ 0.142735] pci 0000:00:1e.0: bridge 32bit mmio: [0xd0000000-0xd03fffff]
Oct 11 12:55:52 kernel: [ 0.142777] pci_bus 0000:00: on NUMA node 0
Oct 11 12:55:52 kernel: [ 0.142786] ACPI: PCI Interrupt Routing Table [\_SB_.C002._PRT]
Oct 11 12:55:52 kernel: [ 0.143060] ACPI: PCI Interrupt Routing Table [\_SB_.C002.C067._PRT]
Oct 11 12:55:52 kernel: [ 0.184067] ACPI: PCI Interrupt Link [C0D7] (IRQs 10 *11)
Oct 11 12:55:52 kernel: [ 0.184578] ACPI: PCI Interrupt Link [C0D8] (IRQs *10 11)
Oct 11 12:55:52 kernel: [ 0.185086] ACPI: PCI Interrupt Link [C0D9] (IRQs *10 11)
Oct 11 12:55:52 kernel: [ 0.185589] ACPI: PCI Interrupt Link [C0DA] (IRQs *10 11)
Oct 11 12:55:52 kernel: [ 0.186093] ACPI: PCI Interrupt Link [C0ED] (IRQs *10 11)
Oct 11 12:55:52 kernel: [ 0.186583] ACPI: PCI Interrupt Link [C0EE] (IRQs 10 11) *0, disabled.
Oct 11 12:55:52 kernel: [ 0.187155] ACPI: PCI Interrupt Link [C0EF] (IRQs *10 11)
Oct 11 12:55:52 kernel: [ 0.187649] ACPI: PCI Interrupt Link [C0F0] (IRQs 10 11) *0, disabled.
Oct 11 12:55:52 kernel: [ 0.188367] PCI: Using ACPI for IRQ routing
Oct 11 12:55:52 kernel: [ 0.188853] hpet clockevent registered
Oct 11 12:55:52 kernel: [ 0.188858] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
Oct 11 12:55:52 kernel: [ 0.188939] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
Oct 11 12:55:52 kernel: [ 0.189143] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
Oct 11 12:55:52 kernel: [ 0.192103] pnp: PnP ACPI init
Oct 11 12:55:52 kernel: [ 0.192176] ACPI: bus type pnp registered
Oct 11 12:55:52 kernel: [ 0.204511] pnp: PnP ACPI: found 11 devices
Oct 11 12:55:52 kernel: [ 0.204579] ACPI: ACPI bus type pnp unregistered
Oct 11 12:55:52 kernel: [ 0.205850] PnPBIOS: Disabled by ACPI PNP
Oct 11 12:55:52 kernel: [ 0.205927] system 00:00: iomem range 0x0-0x9ffff could not be reserved
Oct 11 12:55:52 kernel: [ 0.206001] system 00:00: iomem range 0xe0000-0xfffff could not be reserved
Oct 11 12:55:52 kernel: [ 0.206076] system 00:00: iomem range 0x100000-0x3f7fffff could not be reserved
Oct 11 12:55:52 kernel: [ 0.206179] system 00:08: ioport range 0x500-0x57f has been reserved
Oct 11 12:55:52 kernel: [ 0.206253] system 00:08: iomem range 0xffb00000-0xffbfffff has been reserved
Oct 11 12:55:52 kernel: [ 0.206329] system 00:08: iomem range 0xfff00000-0xffffffff has been reserved
Oct 11 12:55:52 kernel: [ 0.206408] system 00:09: ioport range 0x4d0-0x4d1 has been reserved
Oct 11 12:55:52 kernel: [ 0.206483] system 00:09: ioport range 0x1000-0x107f has been reserved
Oct 11 12:55:52 kernel: [ 0.206557] system 00:09: ioport range 0x1100-0x113f has been reserved
Oct 11 12:55:52 kernel: [ 0.206632] system 00:09: ioport range 0x1200-0x121f has been reserved
Oct 11 12:55:52 kernel: [ 0.206706] system 00:09: iomem range 0xe0000000-0xefffffff has been reserved
Oct 11 12:55:52 kernel: [ 0.206782] system 00:09: iomem range 0xfec00000-0xfec000ff could not be reserved
Oct 11 12:55:52 kernel: [ 0.206880] system 00:09: iomem range 0xfed20000-0xff41ffff could not be reserved
Oct 11 12:55:52 kernel: [ 0.206976] system 00:09: iomem range 0xfed90000-0xfed9afff has been reserved
Oct 11 12:55:52 kernel: [ 0.207054] system 00:0a: iomem range 0xfeda0000-0xfedbffff has been reserved
Oct 11 12:55:52 kernel: [ 0.207130] system 00:0a: iomem range 0xfec01000-0xfec01fff has been reserved
Oct 11 12:55:52 kernel: [ 0.242227] pci 0000:02:06.0: CardBus bridge, secondary bus 0000:03
Oct 11 12:55:52 kernel: [ 0.242300] pci 0000:02:06.0: IO window: 0x003000-0x0030ff
Oct 11 12:55:52 kernel: [ 0.242374] pci 0000:02:06.0: IO window: 0x003400-0x0034ff
Oct 11 12:55:52 kernel: [ 0.242448] pci 0000:02:06.0: PREFETCH window: 0x40000000-0x43ffffff
Oct 11 12:55:52 kernel: [ 0.242525] pci 0000:02:06.0: MEM window: 0x44000000-0x47ffffff
Oct 11 12:55:52 kernel: [ 0.242601] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:02
Oct 11 12:55:52 kernel: [ 0.242672] pci 0000:00:1e.0: IO window: 0x3000-0x3fff
Oct 11 12:55:52 kernel: [ 0.242747] pci 0000:00:1e.0: MEM window: 0xd0000000-0xd03fffff
Oct 11 12:55:52 kernel: [ 0.242822] pci 0000:00:1e.0: PREFETCH window: 0x00000040000000-0x00000043ffffff
Oct 11 12:55:52 kernel: [ 0.242931] pci 0000:00:1e.0: setting latency timer to 64
Oct 11 12:55:52 kernel: [ 0.242950] pci 0000:02:06.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
Oct 11 12:55:52 kernel: [ 0.243031] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
Oct 11 12:55:52 kernel: [ 0.243035] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
Oct 11 12:55:52 kernel: [ 0.243040] pci_bus 0000:02: resource 0 io: [0x3000-0x3fff]
Oct 11 12:55:52 kernel: [ 0.243044] pci_bus 0000:02: resource 1 mem: [0xd0000000-0xd03fffff]
Oct 11 12:55:52 kernel: [ 0.243048] pci_bus 0000:02: resource 2 pref mem [0x40000000-0x43ffffff]
Oct 11 12:55:52 kernel: [ 0.243052] pci_bus 0000:02: resource 3 io: [0x00-0xffff]
Oct 11 12:55:52 kernel: [ 0.243056] pci_bus 0000:02: resource 4 mem: [0x000000-0xffffffff]
Oct 11 12:55:52 kernel: [ 0.243061] pci_bus 0000:03: resource 0 io: [0x3000-0x30ff]
Oct 11 12:55:52 kernel: [ 0.243065] pci_bus 0000:03: resource 1 io: [0x3400-0x34ff]
Oct 11 12:55:52 kernel: [ 0.243069] pci_bus 0000:03: resource 2 pref mem [0x40000000-0x43ffffff]
Oct 11 12:55:52 kernel: [ 0.243073] pci_bus 0000:03: resource 3 mem: [0x44000000-0x47ffffff]
Oct 11 12:55:52 kernel: [ 0.243127] NET: Registered protocol family 2
Oct 11 12:55:52 kernel: [ 0.243301] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
Oct 11 12:55:52 kernel: [ 0.243750] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
Oct 11 12:55:52 kernel: [ 0.245130] TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
Oct 11 12:55:52 kernel: [ 0.245644] TCP: Hash tables configured (established 131072 bind 65536)
Oct 11 12:55:52 kernel: [ 0.245719] TCP reno registered
Oct 11 12:55:52 kernel: [ 0.245954] NET: Registered protocol family 1
Oct 11 12:55:52 kernel: [ 0.246123] Trying to unpack rootfs image as initramfs...
Oct 11 12:55:52 kernel: [ 0.492749] Freeing initrd memory: 5202k freed
Oct 11 12:55:52 kernel: [ 0.499417] audit: initializing netlink socket (disabled)
Oct 11 12:55:52 kernel: [ 0.499518] type=2000 audit(1255265749.496:1): initialized
Oct 11 12:55:52 kernel: [ 0.499859] highmem bounce pool size: 64 pages
Oct 11 12:55:52 kernel: [ 0.499932] HugeTLB registered 4 MB page size, pre-allocated 0 pages
Oct 11 12:55:52 kernel: [ 0.500112] VFS: Disk quotas dquot_6.5.2
Oct 11 12:55:52 kernel: [ 0.500221] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Oct 11 12:55:52 kernel: [ 0.500372] msgmni has been set to 1749
Oct 11 12:55:52 kernel: [ 0.500635] alg: No test for stdrng (krng)
Oct 11 12:55:52 kernel: [ 0.500779] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
Oct 11 12:55:52 kernel: [ 0.500875] io scheduler noop registered
Oct 11 12:55:52 kernel: [ 0.500940] io scheduler anticipatory registered
Oct 11 12:55:52 kernel: [ 0.501007] io scheduler deadline registered
Oct 11 12:55:52 kernel: [ 0.501090] io scheduler cfq registered (default)
Oct 11 12:55:52 kernel: [ 0.501180] pci 0000:00:02.0: Boot video device
Oct 11 12:55:52 kernel: [ 0.501763] isapnp: Scanning for PnP cards...
Oct 11 12:55:52 kernel: [ 0.692038] Switched to high resolution mode on CPU 0
Oct 11 12:55:52 kernel: [ 0.855722] isapnp: No Plug & Play device found
Oct 11 12:55:52 kernel: [ 0.859333] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
Oct 11 12:55:52 kernel: [ 0.860092] serial 0000:00:1e.3: PCI INT B -> GSI 22 (level, low) -> IRQ 22
Oct 11 12:55:52 kernel: [ 0.860171] serial 0000:00:1e.3: PCI INT B disabled
Oct 11 12:55:52 kernel: [ 0.862663] brd: module loaded
Oct 11 12:55:52 kernel: [ 0.862846] PNP: PS/2 Controller [PNP0303:C1BA,PNP0f13:C1BB] at 0x60,0x64 irq 1,12
Oct 11 12:55:52 kernel: [ 0.864816] i8042.c: Detected active multiplexing controller, rev 1.1.
Oct 11 12:55:52 kernel: [ 0.865634] serio: i8042 KBD port at 0x60,0x64 irq 1
Oct 11 12:55:52 kernel: [ 0.865707] serio: i8042 AUX0 port at 0x60,0x64 irq 12
Oct 11 12:55:52 kernel: [ 0.865777] serio: i8042 AUX1 port at 0x60,0x64 irq 12
Oct 11 12:55:52 kernel: [ 0.865847] serio: i8042 AUX2 port at 0x60,0x64 irq 12
Oct 11 12:55:52 kernel: [ 0.865917] serio: i8042 AUX3 port at 0x60,0x64 irq 12
Oct 11 12:55:52 kernel: [ 0.866172] mice: PS/2 mouse device common for all mice
Oct 11 12:55:52 kernel: [ 0.866363] rtc_cmos 00:05: RTC can wake from S4
Oct 11 12:55:52 kernel: [ 0.866579] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
Oct 11 12:55:52 kernel: [ 0.866683] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
Oct 11 12:55:52 kernel: [ 0.866880] EISA: Probing bus 0 at eisa.0
Oct 11 12:55:52 kernel: [ 0.866952] Cannot allocate resource for EISA slot 1
Oct 11 12:55:52 kernel: [ 0.867020] Cannot allocate resource for EISA slot 2
Oct 11 12:55:52 kernel: [ 0.867090] Cannot allocate resource for EISA slot 3
Oct 11 12:55:52 kernel: [ 0.867171] Cannot allocate resource for EISA slot 7
Oct 11 12:55:52 kernel: [ 0.867243] EISA: Detected 0 cards.
Oct 11 12:55:52 kernel: [ 0.867317] cpuidle: using governor ladder
Oct 11 12:55:52 kernel: [ 0.867384] cpuidle: using governor menu
Oct 11 12:55:52 kernel: [ 0.867452] No iBFT detected.
Oct 11 12:55:52 kernel: [ 0.867973] TCP cubic registered
Oct 11 12:55:52 kernel: [ 0.868092] NET: Registered protocol family 10
Oct 11 12:55:52 kernel: [ 0.868691] lo: Disabled Privacy Extensions
Oct 11 12:55:52 kernel: [ 0.869129] Mobile IPv6
Oct 11 12:55:52 kernel: [ 0.869193] NET: Registered protocol family 17
Oct 11 12:55:52 kernel: [ 0.869266] Using IPI Shortcut mode
Oct 11 12:55:52 kernel: [ 0.869582] registered taskstats version 1
Oct 11 12:55:52 kernel: [ 0.869823] rtc_cmos 00:05: setting system clock to 2009-10-11 12:55:50 UTC (1255265750)
Oct 11 12:55:52 kernel: [ 0.869998] Freeing unused kernel memory: 412k freed
Oct 11 12:55:52 kernel: [ 0.870363] Write protecting the kernel text: 2080k
Oct 11 12:55:52 kernel: [ 0.870451] Write protecting the kernel read-only data: 776k
Oct 11 12:55:52 kernel: [ 0.903436] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
Oct 11 12:55:52 kernel: [ 1.184784] Uniform Multi-Platform E-IDE driver
Oct 11 12:55:52 kernel: [ 1.279833] thermal LNXTHERM:01: registered as thermal_zone0
Oct 11 12:55:52 kernel: [ 1.279924] ACPI: Thermal Zone [TZ1] (60 C)
Oct 11 12:55:52 kernel: [ 1.327783] yenta_cardbus 0000:02:06.0: CardBus bridge found [103c:099c]
Oct 11 12:55:52 kernel: [ 1.327886] yenta_cardbus 0000:02:06.0: Enabling burst memory read transactions
Oct 11 12:55:52 kernel: [ 1.327985] yenta_cardbus 0000:02:06.0: Using INTVAL to route CSC interrupts to PCI
Oct 11 12:55:52 kernel: [ 1.328097] yenta_cardbus 0000:02:06.0: Routing CardBus interrupts to PCI
Oct 11 12:55:52 kernel: [ 1.328175] yenta_cardbus 0000:02:06.0: TI: mfunc 0x01aa1b22, devctl 0x64
Oct 11 12:55:52 kernel: [ 1.382322] usbcore: registered new interface driver usbfs
Oct 11 12:55:52 kernel: [ 1.382442] usbcore: registered new interface driver hub
Oct 11 12:55:52 kernel: [ 1.382568] usbcore: registered new device driver usb
Oct 11 12:55:52 kernel: [ 1.386191] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Oct 11 12:55:52 kernel: [ 1.386311] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
Oct 11 12:55:52 kernel: [ 1.386405] ehci_hcd 0000:00:1d.7: setting latency timer to 64
Oct 11 12:55:52 kernel: [ 1.386410] ehci_hcd 0000:00:1d.7: EHCI Host Controller
Oct 11 12:55:52 kernel: [ 1.386541] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
Oct 11 12:55:52 kernel: [ 1.390559] ehci_hcd 0000:00:1d.7: debug port 1
Oct 11 12:55:52 kernel: [ 1.390631] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
Oct 11 12:55:52 kernel: [ 1.390653] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xd0580000
Oct 11 12:55:52 kernel: [ 1.399092] thermal LNXTHERM:02: registered as thermal_zone1
Oct 11 12:55:52 kernel: [ 1.399173] ACPI: Thermal Zone [TZ2] (42 C)
Oct 11 12:55:52 kernel: [ 1.404210] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
Oct 11 12:55:52 kernel: [ 1.404340] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
Oct 11 12:55:52 kernel: [ 1.404414] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Oct 11 12:55:52 kernel: [ 1.404509] usb usb1: Product: EHCI Host Controller
Oct 11 12:55:52 kernel: [ 1.404577] usb usb1: Manufacturer: Linux 2.6.30-2-486 ehci_hcd
Oct 11 12:55:52 kernel: [ 1.404649] usb usb1: SerialNumber: 0000:00:1d.7
Oct 11 12:55:52 kernel: [ 1.404816] usb usb1: configuration #1 chosen from 1 choice
Oct 11 12:55:52 kernel: [ 1.404929] hub 1-0:1.0: USB hub found
Oct 11 12:55:52 kernel: [ 1.405003] hub 1-0:1.0: 8 ports detected
Oct 11 12:55:52 kernel: [ 1.405262] piix 0000:00:1f.1: IDE controller (0x8086:0x266f rev 0x03)
Oct 11 12:55:52 kernel: [ 1.405352] PIIX_IDE 0000:00:1f.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Oct 11 12:55:52 kernel: [ 1.405462] piix 0000:00:1f.1: IDE port disabled
Oct 11 12:55:52 kernel: [ 1.405537] piix 0000:00:1f.1: not 100% native mode: will probe irqs later
Oct 11 12:55:52 kernel: [ 1.405615] ide0: BM-DMA at 0x2580-0x2587
Oct 11 12:55:52 kernel: [ 1.405687] Probing IDE interface ide0...
Oct 11 12:55:52 kernel: [ 1.433281] uhci_hcd: USB Universal Host Controller Interface driver
Oct 11 12:55:52 kernel: [ 1.433991] thermal LNXTHERM:03: registered as thermal_zone2
Oct 11 12:55:52 kernel: [ 1.434072] ACPI: Thermal Zone [TZ3] (25 C)
Oct 11 12:55:52 kernel: [ 1.442351] fan PNP0C0B:00: registered as cooling_device0
Oct 11 12:55:52 kernel: [ 1.442431] ACPI: Fan [C253] (off)
Oct 11 12:55:52 kernel: [ 1.442751] fan PNP0C0B:01: registered as cooling_device1
Oct 11 12:55:52 kernel: [ 1.442826] ACPI: Fan [C254] (off)
Oct 11 12:55:52 kernel: [ 1.443141] fan PNP0C0B:02: registered as cooling_device2
Oct 11 12:55:52 kernel: [ 1.443214] ACPI: Fan [C255] (off)
Oct 11 12:55:52 kernel: [ 1.443529] fan PNP0C0B:03: registered as cooling_device3
Oct 11 12:55:52 kernel: [ 1.443602] ACPI: Fan [C256] (off)
Oct 11 12:55:52 kernel: [ 1.564793] yenta_cardbus 0000:02:06.0: ISA IRQ mask 0x0cf8, PCI irq 18
Oct 11 12:55:52 kernel: [ 1.564874] yenta_cardbus 0000:02:06.0: Socket status: 30000820
Oct 11 12:55:52 kernel: [ 1.564948] pci_bus 0000:02: Raising subordinate bus# of parent bus (#02) from #03 to #06
Oct 11 12:55:52 kernel: [ 1.565053] yenta_cardbus 0000:02:06.0: pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff
Oct 11 12:55:52 kernel: [ 1.565152] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3000-0x3fff: clean.
Oct 11 12:55:52 kernel: [ 1.565597] yenta_cardbus 0000:02:06.0: pcmcia: parent PCI bridge Memory window: 0xd0000000 - 0xd03fffff
Oct 11 12:55:52 kernel: [ 1.565698] yenta_cardbus 0000:02:06.0: pcmcia: parent PCI bridge Memory window: 0x40000000 - 0x43ffffff
Oct 11 12:55:52 kernel: [ 1.704307] hda: TOSHIBA MK4026GAX, ATA DISK drive
Oct 11 12:55:52 kernel: [ 1.716012] usb 1-2: new high speed USB device using ehci_hcd and address 2
Oct 11 12:55:52 kernel: [ 1.848907] usb 1-2: New USB device found, idVendor=1e3d, idProduct=2092
Oct 11 12:55:52 kernel: [ 1.848982] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
Oct 11 12:55:52 kernel: [ 1.849057] usb 1-2: Product: Flash Disk
Oct 11 12:55:52 kernel: [ 1.849125] usb 1-2: Manufacturer: CBM
Oct 11 12:55:52 kernel: [ 1.849191] usb 1-2: SerialNumber: CCCBB999988887777001156
Oct 11 12:55:52 kernel: [ 1.849358] usb 1-2: configuration #1 chosen from 1 choice
Oct 11 12:55:52 kernel: [ 1.880243] SCSI subsystem initialized
Oct 11 12:55:52 kernel: [ 1.889277] Initializing USB Mass Storage driver...
Oct 11 12:55:52 kernel: [ 1.889684] scsi0 : SCSI emulation for USB Mass Storage devices
Oct 11 12:55:52 kernel: [ 1.889963] usbcore: registered new interface driver usb-storage
Oct 11 12:55:52 kernel: [ 1.890036] USB Mass Storage support registered.
Oct 11 12:55:52 kernel: [ 1.891043] usb-storage: device found at 2
Oct 11 12:55:52 kernel: [ 1.891046] usb-storage: waiting for device to settle before scanning
Oct 11 12:55:52 kernel: [ 2.200017] pcmcia_socket pcmcia_socket0: pccard: CardBus card inserted into slot 0
Oct 11 12:55:52 kernel: [ 2.200174] pci 0000:03:00.0: reg 10 32bit mmio: [0xffffe000-0xffffffff]
Oct 11 12:55:52 kernel: [ 2.552008] hdb: SONY CD-RW/DVD-ROM CRX835E, ATAPI CD/DVD-ROM drive
Oct 11 12:55:52 kernel: [ 2.552210] hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
Oct 11 12:55:52 kernel: [ 2.552266] hda: UDMA/100 mode selected
Oct 11 12:55:52 kernel: [ 2.552388] hdb: host max PIO4 wanted PIO255(auto-tune) selected PIO4
Oct 11 12:55:52 kernel: [ 2.558512] hdb: MWDMA2 mode selected
Oct 11 12:55:52 kernel: [ 2.558706] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Oct 11 12:55:52 kernel: [ 2.617357] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
Oct 11 12:55:52 kernel: [ 2.617442] uhci_hcd 0000:00:1d.0: setting latency timer to 64
Oct 11 12:55:52 kernel: [ 2.617447] uhci_hcd 0000:00:1d.0: UHCI Host Controller
Oct 11 12:55:52 kernel: [ 2.617553] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
Oct 11 12:55:52 kernel: [ 2.617675] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00002000
Oct 11 12:55:52 kernel: [ 2.619016] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
Oct 11 12:55:52 kernel: [ 2.619091] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Oct 11 12:55:52 kernel: [ 2.619186] usb usb2: Product: UHCI Host Controller
Oct 11 12:55:52 kernel: [ 2.619253] usb usb2: Manufacturer: Linux 2.6.30-2-486 uhci_hcd
Oct 11 12:55:52 kernel: [ 2.619325] usb usb2: SerialNumber: 0000:00:1d.0
Oct 11 12:55:52 kernel: [ 2.619472] usb usb2: configuration #1 chosen from 1 choice
Oct 11 12:55:52 kernel: [ 2.619581] hub 2-0:1.0: USB hub found
Oct 11 12:55:52 kernel: [ 2.619653] hub 2-0:1.0: 2 ports detected
Oct 11 12:55:52 kernel: [ 2.619852] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
Oct 11 12:55:52 kernel: [ 2.619931] uhci_hcd 0000:00:1d.1: setting latency timer to 64
Oct 11 12:55:52 kernel: [ 2.619936] uhci_hcd 0000:00:1d.1: UHCI Host Controller
Oct 11 12:55:52 kernel: [ 2.620039] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
Oct 11 12:55:52 kernel: [ 2.620166] uhci_hcd 0000:00:1d.1: irq 17, io base 0x00002020
Oct 11 12:55:52 kernel: [ 2.620278] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
Oct 11 12:55:52 kernel: [ 2.620353] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Oct 11 12:55:52 kernel: [ 2.620447] usb usb3: Product: UHCI Host Controller
Oct 11 12:55:52 kernel: [ 2.620515] usb usb3: Manufacturer: Linux 2.6.30-2-486 uhci_hcd
Oct 11 12:55:52 kernel: [ 2.620586] usb usb3: SerialNumber: 0000:00:1d.1
Oct 11 12:55:52 kernel: [ 2.620711] usb usb3: configuration #1 chosen from 1 choice
Oct 11 12:55:52 kernel: [ 2.620818] hub 3-0:1.0: USB hub found
Oct 11 12:55:52 kernel: [ 2.620888] hub 3-0:1.0: 2 ports detected
Oct 11 12:55:52 kernel: [ 2.621075] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
Oct 11 12:55:52 kernel: [ 2.621155] uhci_hcd 0000:00:1d.2: setting latency timer to 64
Oct 11 12:55:52 kernel: [ 2.621160] uhci_hcd 0000:00:1d.2: UHCI Host Controller
Oct 11 12:55:52 kernel: [ 2.621253] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
Oct 11 12:55:52 kernel: [ 2.621372] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00002040
Oct 11 12:55:52 kernel: [ 2.621489] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
Oct 11 12:55:52 kernel: [ 2.621563] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Oct 11 12:55:52 kernel: [ 2.621657] usb usb4: Product: UHCI Host Controller
Oct 11 12:55:52 kernel: [ 2.621724] usb usb4: Manufacturer: Linux 2.6.30-2-486 uhci_hcd
Oct 11 12:55:52 kernel: [ 2.621795] usb usb4: SerialNumber: 0000:00:1d.2
Oct 11 12:55:52 kernel: [ 2.621921] usb usb4: configuration #1 chosen from 1 choice
Oct 11 12:55:52 kernel: [ 2.622025] hub 4-0:1.0: USB hub found
Oct 11 12:55:52 kernel: [ 2.622095] hub 4-0:1.0: 2 ports detected
Oct 11 12:55:52 kernel: [ 2.622283] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
Oct 11 12:55:52 kernel: [ 2.622362] uhci_hcd 0000:00:1d.3: setting latency timer to 64
Oct 11 12:55:52 kernel: [ 2.622367] uhci_hcd 0000:00:1d.3: UHCI Host Controller
Oct 11 12:55:52 kernel: [ 2.622459] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
Oct 11 12:55:52 kernel: [ 2.622582] uhci_hcd 0000:00:1d.3: irq 19, io base 0x00002060
Oct 11 12:55:52 kernel: [ 2.622693] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
Oct 11 12:55:52 kernel: [ 2.622768] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Oct 11 12:55:52 kernel: [ 2.622861] usb usb5: Product: UHCI Host Controller
Oct 11 12:55:52 kernel: [ 2.622930] usb usb5: Manufacturer: Linux 2.6.30-2-486 uhci_hcd
Oct 11 12:55:52 kernel: [ 2.623002] usb usb5: SerialNumber: 0000:00:1d.3
Oct 11 12:55:52 kernel: [ 2.623126] usb usb5: configuration #1 chosen from 1 choice
Oct 11 12:55:52 kernel: [ 2.623232] hub 5-0:1.0: USB hub found
Oct 11 12:55:52 kernel: [ 2.623302] hub 5-0:1.0: 2 ports detected
Oct 11 12:55:52 kernel: [ 2.659190] ide-gd driver 1.18
Oct 11 12:55:52 kernel: [ 2.659295] hda: max request size: 128KiB
Oct 11 12:55:52 kernel: [ 2.674254] ide-cd driver 5.00
Oct 11 12:55:52 kernel: [ 2.674655] hda: 78140160 sectors (40007 MB), CHS=65535/16/63
Oct 11 12:55:52 kernel: [ 2.674848] hda: cache flushes supported
Oct 11 12:55:52 kernel: [ 2.674984] hda: hda1 hda2
Oct 11 12:55:52 kernel: [ 2.683595] ide-cd: hdb: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache
Oct 11 12:55:52 kernel: [ 2.683842] Uniform CD-ROM driver Revision: 3.20
Oct 11 12:55:53 frontend: Setting debconf/priority to low
Oct 11 12:55:53 kernel: [ 4.013690] vga16fb: initializing
Oct 11 12:55:53 kernel: [ 4.013697] vga16fb: mapped to 0xc00a0000
Oct 11 12:55:53 kernel: [ 4.132173] Console: switching to colour frame buffer device 80x30
Oct 11 12:55:53 kernel: [ 4.141910] fb0: VGA16 VGA frame buffer device
Oct 11 12:55:53 init: starting pid 620, tty '': '/sbin/reopen-console /sbin/debian-installer'
Oct 11 12:55:53 init: starting pid 628, tty '/dev/tty4': '/usr/bin/tail -f /var/log/syslog'
Oct 11 12:55:54 debconf: Setting debconf/language to en
Oct 11 12:55:54 main-menu[635]: DEBUG: resolver (libc6-udeb): package doesn't exist (ignored)
Oct 11 12:55:56 kernel: [ 6.888207] usb-storage: device scan complete
Oct 11 12:55:56 kernel: [ 6.888708] scsi 0:0:0:0: Direct-Access CBM Flash Disk 5.00 PQ: 0 ANSI: 2
Oct 11 12:55:56 kernel: [ 6.901772] Driver 'sd' needs updating - please use bus_type methods
Oct 11 12:55:56 kernel: [ 6.903055] sd 0:0:0:0: [sda] 8105984 512-byte hardware sectors: (4.15 GB/3.86 GiB)
Oct 11 12:55:56 kernel: [ 6.903545] sd 0:0:0:0: [sda] Write Protect is off
Oct 11 12:55:56 kernel: [ 6.903550] sd 0:0:0:0: [sda] Mode Sense: 0b 00 00 08
Oct 11 12:55:56 kernel: [ 6.903553] sd 0:0:0:0: [sda] Assuming drive cache: write through
Oct 11 12:55:56 kernel: [ 6.905295] sd 0:0:0:0: [sda] Assuming drive cache: write through
Oct 11 12:55:56 kernel: [ 6.905299] sda:
Oct 11 12:55:56 kernel: [ 6.906116] sd 0:0:0:0: [sda] Attached SCSI removable disk
Oct 11 12:56:04 main-menu[635]: INFO: Menu item 'iso-scan' selected
Oct 11 12:56:04 main-menu[635]: INFO: Falling back to the package description for loop-modules-2.6.30-2-486-di
Oct 11 12:56:04 main-menu[635]: INFO: Falling back to the package description for loop-modules-2.6.30-2-486-di
Oct 11 12:56:05 net/hw-detect.hotplug: Detected hotpluggable network interface lo
Oct 11 12:56:05 hw-detect: ISA bus detected; loading module 'ide-generic'
Oct 11 12:56:05 hw-detect: insmod /lib/modules/2.6.30-2-486/kernel/drivers/ide/ide-generic.ko
Oct 11 12:56:05 kernel: [ 15.900537] ide_generic: please use "probe_mask=0x3f" module parameter for probing all legacy ISA IDE ports
Oct 11 12:56:05 hw-detect: Detected PCMCIA, installing pcmciautils.
Oct 11 12:56:05 apt-install: Queueing package pcmciautils for later installation
Oct 11 12:56:05 apt-install: Queueing package udev for later installation
Oct 11 12:56:05 apt-install: Queueing package usbutils for later installation
Oct 11 12:56:05 apt-install: Queueing package acpi for later installation
Oct 11 12:56:05 apt-install: Queueing package acpid for later installation
Oct 11 12:56:05 apt-install: Queueing package acpi-support-base for later installation
Oct 11 12:56:05 apt-install: Queueing package eject for later installation
Oct 11 12:56:05 apt-install: Queueing package libc6-i686 for later installation
Oct 11 12:56:06 check-missing-firmware: no missing firmware in /tmp/missing-firmware
Oct 11 12:56:06 kernel: [ 17.192471] loop: module loaded
Oct 11 12:56:06 iso-scan: First pass: Look for ISOs near top-level of each filesystem.
Oct 11 12:56:07 iso-scan: Mounted /dev/hda1 for first pass
Oct 11 12:56:07 iso-scan: Failed mounting /dev/hda1
Oct 11 12:56:07 kernel: [ 17.571957] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
Oct 11 12:56:07 iso-scan: Waiting for /dev/hda2 to possibly get ready..
Oct 11 12:56:10 kernel: [ 20.670610] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
Oct 11 12:56:10 kernel: [ 20.731005] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
Oct 11 12:56:10 iso-scan: Waiting for /dev/hda to possibly get ready..
Oct 11 12:56:13 kernel: [ 23.829640] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
Oct 11 12:56:13 kernel: [ 23.855366] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
Oct 11 12:56:13 iso-scan: Mounted /dev/sda for first pass
Oct 11 12:56:13 iso-scan: Found ISO ./debian-testing-i386-netinst.iso on /dev/sda
Oct 11 12:56:13 kernel: [ 23.879372] ISO 9660 Extensions: Microsoft Joliet Level 3
Oct 11 12:56:13 kernel: [ 23.880995] ISO 9660 Extensions: RRIP_1991A
Oct 11 12:56:13 iso-scan: Detected ISO with 'testing' (squeeze) distribution
Oct 11 12:56:27 anna-install: Queueing udeb apt-mirror-setup for later installation
Oct 11 12:56:27 anna-install: Queueing udeb apt-cdrom-setup for later installation
Oct 11 12:56:27 anna-install: Queueing udeb squeeze-support for later installation
Oct 11 12:56:27 main-menu[635]: DEBUG: resolver (libc6-udeb): package doesn't exist (ignored)
Oct 11 12:56:29 main-menu[635]: INFO: Menu item 'load-iso' selected
Oct 11 12:56:29 cdrom-retriever: warning: Unable to find contrib/debian-installer/binary-i386/Packages in /cdrom/dists/squeeze/Release.
Oct 11 12:56:29 cdrom-retriever: warning: Unable to find contrib/debian-installer/binary-i386/Packages.gz in /cdrom/dists/squeeze/Release.
Oct 11 12:56:29 anna[1617]: DEBUG: resolver (cdrom-detect): package doesn't exist (ignored)
Oct 11 12:56:29 anna[1617]: DEBUG: resolver (fat-modules): package doesn't exist (ignored)
Oct 11 12:56:31 anna[1617]: DEBUG: resolver (cdrom-detect): package doesn't exist (ignored)
Oct 11 12:56:31 anna[1617]: DEBUG: resolver (fat-modules): package doesn't exist (ignored)
Oct 11 12:56:31 anna[1617]: DEBUG: retrieving apt-cdrom-setup 1:0.42
Oct 11 12:56:31 anna[1617]: DEBUG: retrieving apt-mirror-setup 1:0.42
Oct 11 12:56:31 anna[1617]: DEBUG: retrieving apt-setup-udeb 1:0.42
Oct 11 12:56:31 anna[1617]: DEBUG: retrieving base-installer 1.102
Oct 11 12:56:31 anna[1617]: DEBUG: retrieving bootstrap-base 1.102
Oct 11 12:56:31 anna[1617]: DEBUG: retrieving choose-mirror-bin 2.29
Oct 11 12:56:31 anna[1617]: DEBUG: retrieving clock-setup 0.100
Oct 11 12:56:31 anna[1617]: DEBUG: retrieving crc-modules-2.6.30-2-486-di 1.84
Oct 11 12:56:31 anna[1617]: DEBUG: retrieving debian-archive-keyring-udeb 2009.01.31
Oct 11 12:56:31 anna[1617]: DEBUG: retrieving debootstrap-udeb 1.0.20
Oct 11 12:56:31 anna[1617]: DEBUG: retrieving di-utils-mapdevfs 1.71+b1
Oct 11 12:56:31 anna[1617]: DEBUG: retrieving disk-detect 1.73
Oct 11 12:56:31 anna[1617]: DEBUG: retrieving e2fsprogs-udeb 1.41.9-1
Oct 11 12:56:32 anna[1617]: DEBUG: retrieving efi-modules-2.6.30-2-486-di 1.84
Oct 11 12:56:32 anna[1617]: DEBUG: retrieving elilo-installer 1.15
Oct 11 12:56:32 anna[1617]: DEBUG: retrieving ext2-modules-2.6.30-2-486-di 1.84
Oct 11 12:56:32 anna[1617]: DEBUG: retrieving ext3-modules-2.6.30-2-486-di 1.84
Oct 11 12:56:32 anna[1617]: DEBUG: retrieving ext4-modules-2.6.30-2-486-di 1.84
Oct 11 12:56:32 anna[1617]: DEBUG: retrieving fdisk-udeb 2.16.1-3
Oct 11 12:56:32 anna[1617]: DEBUG: retrieving finish-install 2.23
Oct 11 12:56:32 anna[1617]: DEBUG: retrieving firewire-core-modules-2.6.30-2-486-di 1.84
Oct 11 12:56:32 anna[1617]: DEBUG: retrieving floppy-modules-2.6.30-2-486-di 1.84
Oct 11 12:56:32 anna[1617]: DEBUG: retrieving gpgv-udeb 1.4.10-2
Oct 11 12:56:32 anna[1617]: DEBUG: retrieving grub-installer 1.46
Oct 11 12:56:32 anna[1617]: DEBUG: retrieving jfs-modules-2.6.30-2-486-di 1.84
Oct 11 12:56:32 anna[1617]: DEBUG: retrieving jfsutils-udeb 1.1.12-2
Oct 11 12:56:32 anna[1617]: DEBUG: retrieving kickseed-common 0.53
Oct 11 12:56:32 anna[1617]: DEBUG: retrieving libbsd0-udeb 0.1.6-1
Oct 11 12:56:32 anna[1617]: DEBUG: retrieving libc6-udeb 2.9-27
Oct 11 12:56:32 anna[1617]: DEBUG: retrieving libdevmapper1.02.1-udeb 2:1.02.38-2
Oct 11 12:56:32 anna[1617]: DEBUG: retrieving libparted1.8-udeb 1.8.8.git.2009.07.19-5
Oct 11 12:56:32 anna[1617]: DEBUG: retrieving libsysfs2-udeb 2.1.0-6
Oct 11 12:56:32 anna[1617]: DEBUG: retrieving lilo-installer 1.30
Oct 11 12:56:32 anna[1617]: DEBUG: retrieving loop-modules-2.6.30-2-486-di 1.84
Oct 11 12:56:32 anna[1617]: DEBUG: retrieving md-modules-2.6.30-2-486-di 1.84
Oct 11 12:56:33 anna[1617]: DEBUG: retrieving mdadm-udeb 3.0-3.1
Oct 11 12:56:33 anna[1617]: DEBUG: retrieving mkreiserfs-udeb 1:3.6.21-1
Oct 11 12:56:33 anna[1617]: DEBUG: retrieving network-preseed 1.42
Oct 11 12:56:33 anna[1617]: DEBUG: retrieving nic-extra-modules-2.6.30-2-486-di 1.84
Oct 11 12:56:33 anna[1617]: DEBUG: retrieving nic-modules-2.6.30-2-486-di 1.84
Oct 11 12:56:33 anna[1617]: DEBUG: retrieving nic-pcmcia-modules-2.6.30-2-486-di 1.84
Oct 11 12:56:33 anna[1617]: DEBUG: retrieving nic-shared-modules-2.6.30-2-486-di 1.84
Oct 11 12:56:33 anna[1617]: DEBUG: retrieving nic-usb-modules-2.6.30-2-486-di 1.84
Oct 11 12:56:33 anna[1617]: DEBUG: retrieving nic-wireless-modules-2.6.30-2-486-di 1.84
Oct 11 12:56:33 anna[1617]: DEBUG: retrieving nobootloader 1.25
Oct 11 12:56:33 anna[1617]: DEBUG: retrieving ntfsprogs-udeb 2.0.0-1
Oct 11 12:56:33 anna[1617]: DEBUG: retrieving os-prober-udeb 1.35
Oct 11 12:56:33 anna[1617]: DEBUG: retrieving partconf-find-partitions 1.32
Oct 11 12:56:33 anna[1617]: DEBUG: retrieving partman-auto 89
Oct 11 12:56:33 anna[1617]: DEBUG: retrieving partman-auto-raid 15
Oct 11 12:56:33 anna[1617]: DEBUG: retrieving partman-base 135
Oct 11 12:56:34 anna[1617]: DEBUG: retrieving partman-basicfilesystems 63
Oct 11 12:56:34 anna[1617]: DEBUG: retrieving partman-basicmethods 43
Oct 11 12:56:34 anna[1617]: DEBUG: retrieving partman-efi 20
Oct 11 12:56:34 anna[1617]: DEBUG: retrieving partman-ext3 58
Oct 11 12:56:34 anna[1617]: DEBUG: retrieving partman-jfs 30
Oct 11 12:56:34 anna[1617]: DEBUG: retrieving partman-md 48
Oct 11 12:56:34 anna[1617]: DEBUG: retrieving partman-partitioning 72
Oct 11 12:56:34 anna[1617]: DEBUG: retrieving partman-reiserfs 45
Oct 11 12:56:34 anna[1617]: DEBUG: retrieving partman-target 64
Oct 11 12:56:34 anna[1617]: DEBUG: retrieving partman-utils 135
Oct 11 12:56:34 anna[1617]: DEBUG: retrieving partman-xfs 44
Oct 11 12:56:34 anna[1617]: DEBUG: retrieving pata-modules-2.6.30-2-486-di 1.84
Oct 11 12:56:34 anna[1617]: DEBUG: retrieving pcmcia-storage-modules-2.6.30-2-486-di 1.84
Oct 11 12:56:34 anna[1617]: DEBUG: retrieving pcmciautils-udeb 014-4
Oct 11 12:56:34 anna[1617]: DEBUG: retrieving pkgsel 0.25
Oct 11 12:56:34 anna[1617]: DEBUG: retrieving rdate-udeb 1:1.2-4
Oct 11 12:56:34 anna[1617]: DEBUG: retrieving reiserfs-modules-2.6.30-2-486-di 1.84
Oct 11 12:56:34 anna[1617]: DEBUG: retrieving scsi-extra-modules-2.6.30-2-486-di 1.84
Oct 11 12:56:34 anna[1617]: DEBUG: retrieving tzsetup-udeb 1:0.26
Oct 11 12:56:35 anna[1617]: DEBUG: retrieving user-setup-udeb 1.28
Oct 11 12:56:35 anna[1617]: DEBUG: retrieving xfs-modules-2.6.30-2-486-di 1.84
Oct 11 12:56:35 anna[1617]: DEBUG: retrieving xfsprogs-udeb 3.0.4
Oct 11 12:57:08 main-menu[635]: INFO: Menu item 'ethdetect' selected
Oct 11 12:57:09 kernel: [ 79.447452] b44 0000:02:0e.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Oct 11 12:57:09 kernel: [ 79.458896] cfg80211: Using static regulatory domain info
Oct 11 12:57:09 kernel: [ 79.458900] cfg80211: Regulatory domain: US
Oct 11 12:57:09 kernel: [ 79.458903] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Oct 11 12:57:09 kernel: [ 79.458908] (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
Oct 11 12:57:09 kernel: [ 79.458912] (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
Oct 11 12:57:09 kernel: [ 79.458917] (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
Oct 11 12:57:09 kernel: [ 79.458921] (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
Oct 11 12:57:09 kernel: [ 79.458925] (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
Oct 11 12:57:09 kernel: [ 79.458930] (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
Oct 11 12:57:09 kernel: [ 79.458943] cfg80211: Calling CRDA for country: US
Oct 11 12:57:09 net/hw-detect.hotplug: Detected hotpluggable network interface lo
Oct 11 12:57:09 kernel: [ 79.502990] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: clean.
Oct 11 12:57:09 kernel: [ 79.506093] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: clean.
Oct 11 12:57:09 kernel: [ 79.506854] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: clean.
Oct 11 12:57:09 kernel: [ 79.507470] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: clean.
Oct 11 12:57:09 kernel: [ 79.508663] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
Oct 11 12:57:09 kernel: [ 79.527733] rt2500pci 0000:03:00.0: enabling device (0000 -> 0002)
Oct 11 12:57:09 kernel: [ 79.527747] rt2500pci 0000:03:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
Oct 11 12:57:09 kernel: [ 79.527759] rt2500pci 0000:03:00.0: setting latency timer to 64
Oct 11 12:57:09 kernel: [ 79.554698] phy0: Selected rate control algorithm 'minstrel'
Oct 11 12:57:09 kernel: [ 79.555411] Registered led device: rt2500pci-phy0::radio
Oct 11 12:57:09 kernel: [ 79.555432] Registered led device: rt2500pci-phy0::quality
Oct 11 12:57:09 net/hw-detect.hotplug: Detected hotpluggable network interface wmaster0
Oct 11 12:57:09 net/hw-detect.hotplug: Detected hotpluggable network interface wlan0
Oct 11 12:57:09 kernel: [ 79.580116] ssb: Sonics Silicon Backplane found on PCI device 0000:02:0e.0
Oct 11 12:57:09 kernel: [ 79.580148] b44.c:v2.0
Oct 11 12:57:09 kernel: [ 79.580190] firewire_ohci 0000:02:06.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22
Oct 11 12:57:09 kernel: [ 79.600941] eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:12:79:bf:03:97
Oct 11 12:57:09 net/hw-detect.hotplug: Detected hotpluggable network interface eth0
Oct 11 12:57:09 kernel: [ 79.652009] firewire_ohci: Added fw-ohci device 0000:02:06.2, OHCI version 1.10
Oct 11 12:57:09 hw-detect: insmod /lib/modules/2.6.30-2-486/kernel/drivers/firewire/firewire-sbp2.ko
Oct 11 12:57:09 kernel: [ 80.152140] firewire_core: created device fw0: GUID 718b5000ffffffa6, S400
Oct 11 12:57:09 hw-detect: Missing modules 'eth1394 (FireWire ethernet)
Oct 11 12:57:10 check-missing-firmware: no missing firmware in /tmp/missing-firmware
Oct 11 12:57:11 kernel: [ 81.768970] ADDRCONF(NETDEV_UP): wlan0: link is not ready
Oct 11 12:57:11 kernel: [ 81.775443] ADDRCONF(NETDEV_UP): eth0: link is not ready
Oct 11 12:57:11 kernel: [ 81.778251] b44: eth0: powering down PHY
Oct 11 12:57:12 check-missing-firmware: no missing firmware in /tmp/missing-firmware
Oct 11 12:57:12 main-menu[635]: (process:3361): ip: SIOCSIFFLAGS: Operation not supported
Oct 11 12:57:25 kernel: [ 96.286801] usb 1-2: USB disconnect, address 2
Oct 11 12:58:15 main-menu[635]: INFO: Menu item 'netcfg' selected
Oct 11 12:58:15 kernel: [ 145.568220] ADDRCONF(NETDEV_UP): eth0: link is not ready
Oct 11 12:58:15 netcfg[4204]: INFO: eth0 is disconnected. (MII)
Oct 11 12:58:15 netcfg[4204]: INFO: eth0 is not a wireless interface. Continuing.
Oct 11 12:58:15 kernel: [ 145.573460] b44: eth0: powering down PHY
Oct 11 12:58:15 netcfg[4204]: INFO: ethtool ioctl on wlan0 failed
Oct 11 12:58:15 netcfg[4204]: WARNING **: couldn't determine MII ioctl to use for wlan0
Oct 11 12:58:15 kernel: [ 145.584506] ADDRCONF(NETDEV_UP): wlan0: link is not ready
Oct 11 12:58:16 netcfg[4204]: INFO: wlan0 is not associated. Relegating to defwireless
Oct 11 12:58:16 kernel: [ 146.592499] wlan0: deauthenticating by local choice (reason=3)
Oct 11 12:58:31 apt-install: Queueing package wireless-tools for later installation
Oct 11 12:59:45 netcfg[4204]: INFO: eth0 is disconnected. (MII)
Oct 11 12:59:45 netcfg[4204]: INFO: eth0 is not a wireless interface. Continuing.
Oct 11 12:59:45 kernel: [ 236.125289] ADDRCONF(NETDEV_UP): eth0: link is not ready
Oct 11 12:59:45 kernel: [ 236.127800] b44: eth0: powering down PHY
Oct 11 12:59:45 netcfg[4204]: INFO: ethtool ioctl on wlan0 failed
Oct 11 12:59:45 netcfg[4204]: WARNING **: couldn't determine MII ioctl to use for wlan0
Oct 11 12:59:45 kernel: [ 236.140504] ADDRCONF(NETDEV_UP): wlan0: link is not ready
Oct 11 12:59:46 netcfg[4204]: INFO: wlan0 is not associated. Relegating to defwireless
Oct 11 12:59:46 kernel: [ 237.148339] wlan0: deauthenticating by local choice (reason=3)
Oct 11 12:59:49 main-menu[635]: INFO: Menu item 'netcfg' succeeded but requested to be left unconfigured.
Oct 11 12:59:55 main-menu[635]: INFO: Falling back to the package description for auto-install
Oct 11 12:59:55 main-menu[635]: INFO: Falling back to the package description for ai-choosers
Oct 11 12:59:55 main-menu[635]: INFO: Menu item 'di-utils-shell' selected
Oct 11 13:00:03 kernel: [ 254.308011] usb 1-2: new high speed USB device using ehci_hcd and address 3
Oct 11 13:00:04 kernel: [ 254.440825] usb 1-2: New USB device found, idVendor=1e3d, idProduct=2092
Oct 11 13:00:04 kernel: [ 254.440830] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
Oct 11 13:00:04 kernel: [ 254.440834] usb 1-2: Product: Flash Disk
Oct 11 13:00:04 kernel: [ 254.440837] usb 1-2: Manufacturer: CBM
Oct 11 13:00:04 kernel: [ 254.440841] usb 1-2: SerialNumber: CCCBB999988887777001156
Oct 11 13:00:04 kernel: [ 254.440965] usb 1-2: configuration #1 chosen from 1 choice
Oct 11 13:00:04 kernel: [ 254.443502] scsi1 : SCSI emulation for USB Mass Storage devices
Oct 11 13:00:04 kernel: [ 254.445523] usb-storage: device found at 3
Oct 11 13:00:04 kernel: [ 254.445527] usb-storage: waiting for device to settle before scanning
Oct 11 13:00:09 kernel: [ 259.444118] usb-storage: device scan complete
Oct 11 13:00:09 kernel: [ 259.444624] scsi 1:0:0:0: Direct-Access CBM Flash Disk 5.00 PQ: 0 ANSI: 2
Oct 11 13:00:09 kernel: [ 259.448604] sd 1:0:0:0: [sdb] 8105984 512-byte hardware sectors: (4.15 GB/3.86 GiB)
Oct 11 13:00:09 kernel: [ 259.449089] sd 1:0:0:0: [sdb] Write Protect is off
Oct 11 13:00:09 kernel: [ 259.449094] sd 1:0:0:0: [sdb] Mode Sense: 0b 00 00 08
Oct 11 13:00:09 kernel: [ 259.449098] sd 1:0:0:0: [sdb] Assuming drive cache: write through
Oct 11 13:00:09 kernel: [ 259.450710] sd 1:0:0:0: [sdb] Assuming drive cache: write through
Oct 11 13:00:09 kernel: [ 259.450717] sdb:
Oct 11 13:00:09 kernel: [ 259.451537] sd 1:0:0:0: [sdb] Attached SCSI removable disk
Oct 11 13:00:19 kernel: [ 270.320497] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
Oct 11 13:00:50 kernel: [ 300.459694] usb 1-2: USB disconnect, address 3
Oct 11 13:03:47 kernel: [ 477.720415] ADDRCONF(NETDEV_UP): wlan0: link is not ready
Oct 11 13:03:49 kernel: [ 479.572128] wlan0: authenticate with AP 00:02:cf:6a:32:c8
Oct 11 13:03:49 kernel: [ 479.573359] wlan0: authenticated
Oct 11 13:03:49 kernel: [ 479.573363] wlan0: associate with AP 00:02:cf:6a:32:c8
Oct 11 13:03:49 kernel: [ 479.576162] wlan0: RX AssocResp from 00:02:cf:6a:32:c8 (capab=0x471 status=0 aid=3)
Oct 11 13:03:49 kernel: [ 479.576166] wlan0: associated
Oct 11 13:03:49 kernel: [ 479.577237] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Oct 11 13:03:59 kernel: [ 490.248005] wlan0: no IPv6 routers present
Oct 11 13:04:00 kernel: [ 491.305795] wlan0: deauthenticated (Reason: 1)
Oct 11 13:04:01 kernel: [ 492.304009] wlan0: direct probe to AP 00:02:cf:6a:32:c8 try 1
Oct 11 13:04:01 kernel: [ 492.305524] wlan0 direct probe responded
Oct 11 13:04:01 kernel: [ 492.305528] wlan0: authenticate with AP 00:02:cf:6a:32:c8
Oct 11 13:04:01 kernel: [ 492.309092] wlan0: authenticated
Oct 11 13:04:01 kernel: [ 492.309096] wlan0: associate with AP 00:02:cf:6a:32:c8
Oct 11 13:04:01 kernel: [ 492.312984] wlan0: RX ReassocResp from 00:02:cf:6a:32:c8 (capab=0x471 status=0 aid=3)
Oct 11 13:04:01 kernel: [ 492.312989] wlan0: associated
Oct 11 13:04:13 kernel: [ 504.305674] wlan0: deauthenticated (Reason: 1)
Oct 11 13:04:14 kernel: [ 505.304008] wlan0: direct probe to AP 00:02:cf:6a:32:c8 try 1
Oct 11 13:04:14 kernel: [ 505.305501] wlan0 direct probe responded
Oct 11 13:04:14 kernel: [ 505.305505] wlan0: authenticate with AP 00:02:cf:6a:32:c8
Oct 11 13:04:14 kernel: [ 505.309042] wlan0: authenticated
Oct 11 13:04:14 kernel: [ 505.309046] wlan0: associate with AP 00:02:cf:6a:32:c8
Oct 11 13:04:14 kernel: [ 505.312622] wlan0: RX ReassocResp from 00:02:cf:6a:32:c8 (capab=0x471 status=0 aid=3)
Oct 11 13:04:14 kernel: [ 505.312627] wlan0: associated
Oct 11 13:04:22 kernel: [ 513.072943] wlan0: deauthenticating by local choice (reason=3)
Oct 11 13:04:22 kernel: [ 513.073631] wlan0: deauthenticating by local choice (reason=3)
Oct 11 13:18:13 kernel: [ 1343.860011] usb 1-2: new high speed USB device using ehci_hcd and address 4
Oct 11 13:18:13 kernel: [ 1343.992909] usb 1-2: New USB device found, idVendor=1e3d, idProduct=2092
Oct 11 13:18:13 kernel: [ 1343.992914] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
Oct 11 13:18:13 kernel: [ 1343.992918] usb 1-2: Product: Flash Disk
Oct 11 13:18:13 kernel: [ 1343.992921] usb 1-2: Manufacturer: CBM
Oct 11 13:18:13 kernel: [ 1343.992924] usb 1-2: SerialNumber: CCCBB999988887777001156
Oct 11 13:18:13 kernel: [ 1343.993040] usb 1-2: configuration #1 chosen from 1 choice
Oct 11 13:18:13 kernel: [ 1343.995582] scsi2 : SCSI emulation for USB Mass Storage devices
Oct 11 13:18:13 kernel: [ 1343.997586] usb-storage: device found at 4
Oct 11 13:18:13 kernel: [ 1343.997590] usb-storage: waiting for device to settle before scanning
Oct 11 13:18:18 kernel: [ 1348.996199] usb-storage: device scan complete
Oct 11 13:18:18 kernel: [ 1348.996706] scsi 2:0:0:0: Direct-Access CBM Flash Disk 5.00 PQ: 0 ANSI: 2
Oct 11 13:18:18 kernel: [ 1349.000567] sd 2:0:0:0: [sdb] 8105984 512-byte hardware sectors: (4.15 GB/3.86 GiB)
Oct 11 13:18:18 kernel: [ 1349.001045] sd 2:0:0:0: [sdb] Write Protect is off
Oct 11 13:18:18 kernel: [ 1349.001050] sd 2:0:0:0: [sdb] Mode Sense: 0b 00 00 08
Oct 11 13:18:18 kernel: [ 1349.001054] sd 2:0:0:0: [sdb] Assuming drive cache: write through
Oct 11 13:18:18 kernel: [ 1349.002670] sd 2:0:0:0: [sdb] Assuming drive cache: write through
Oct 11 13:18:18 kernel: [ 1349.002677] sdb:
Oct 11 13:18:18 kernel: [ 1349.003497] sd 2:0:0:0: [sdb] Attached SCSI removable disk
Oct 11 13:18:30 kernel: [ 1361.005737] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
Oct 11 13:18:40 kernel: [ 1370.970278] usb 1-2: USB disconnect, address 4
Oct 11 13:19:14 kernel: [ 1404.436429] ADDRCONF(NETDEV_UP): wlan0: link is not ready
Oct 11 13:19:15 kernel: [ 1405.924226] wlan0: direct probe to AP 00:02:cf:6a:32:c8 try 1
Oct 11 13:19:15 kernel: [ 1405.925722] wlan0 direct probe responded
Oct 11 13:19:15 kernel: [ 1405.925726] wlan0: authenticate with AP 00:02:cf:6a:32:c8
Oct 11 13:19:15 kernel: [ 1405.929195] wlan0: authenticated
Oct 11 13:19:15 kernel: [ 1405.929199] wlan0: associate with AP 00:02:cf:6a:32:c8
Oct 11 13:19:15 kernel: [ 1405.932996] wlan0: RX AssocResp from 00:02:cf:6a:32:c8 (capab=0x471 status=0 aid=3)
Oct 11 13:19:15 kernel: [ 1405.933000] wlan0: associated
Oct 11 13:19:15 kernel: [ 1405.933798] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Oct 11 13:19:26 kernel: [ 1416.472006] wlan0: no IPv6 routers present
Oct 11 13:19:26 kernel: [ 1417.294294] wlan0: deauthenticated (Reason: 1)
Oct 11 13:19:27 kernel: [ 1418.292009] wlan0: direct probe to AP 00:02:cf:6a:32:c8 try 1
Oct 11 13:19:27 kernel: [ 1418.293564] wlan0 direct probe responded
Oct 11 13:19:27 kernel: [ 1418.293568] wlan0: authenticate with AP 00:02:cf:6a:32:c8
Oct 11 13:19:27 kernel: [ 1418.297104] wlan0: authenticated
Oct 11 13:19:27 kernel: [ 1418.297108] wlan0: associate with AP 00:02:cf:6a:32:c8
Oct 11 13:19:27 kernel: [ 1418.300504] wlan0: RX ReassocResp from 00:02:cf:6a:32:c8 (capab=0x471 status=0 aid=3)
Oct 11 13:19:27 kernel: [ 1418.300508] wlan0: associated
Oct 11 13:19:39 kernel: [ 1430.293928] wlan0: deauthenticated (Reason: 1)
Oct 11 13:19:40 kernel: [ 1431.292009] wlan0: direct probe to AP 00:02:cf:6a:32:c8 try 1
Oct 11 13:19:40 kernel: [ 1431.293486] wlan0 direct probe responded
Oct 11 13:19:40 kernel: [ 1431.293490] wlan0: authenticate with AP 00:02:cf:6a:32:c8
Oct 11 13:19:40 kernel: [ 1431.297017] wlan0: authenticated
Oct 11 13:19:40 kernel: [ 1431.297022] wlan0: associate with AP 00:02:cf:6a:32:c8
Oct 11 13:19:40 kernel: [ 1431.300543] wlan0: RX ReassocResp from 00:02:cf:6a:32:c8 (capab=0x471 status=0 aid=3)
Oct 11 13:19:40 kernel: [ 1431.300547] wlan0: associated
Oct 11 13:19:52 kernel: [ 1443.293850] wlan0: deauthenticated (Reason: 1)
Oct 11 13:19:53 kernel: [ 1444.292009] wlan0: direct probe to AP 00:02:cf:6a:32:c8 try 1
Oct 11 13:19:53 kernel: [ 1444.293502] wlan0 direct probe responded
Oct 11 13:19:53 kernel: [ 1444.293506] wlan0: authenticate with AP 00:02:cf:6a:32:c8
Oct 11 13:19:53 kernel: [ 1444.297256] wlan0: authenticated
Oct 11 13:19:53 kernel: [ 1444.297260] wlan0: associate with AP 00:02:cf:6a:32:c8
Oct 11 13:19:53 kernel: [ 1444.300744] wlan0: RX ReassocResp from 00:02:cf:6a:32:c8 (capab=0x471 status=0 aid=3)
Oct 11 13:19:53 kernel: [ 1444.300748] wlan0: associated
Oct 11 13:20:05 kernel: [ 1456.293655] wlan0: deauthenticated (Reason: 1)
Oct 11 13:20:06 kernel: [ 1457.292008] wlan0: direct probe to AP 00:02:cf:6a:32:c8 try 1
Oct 11 13:20:06 kernel: [ 1457.293465] wlan0 direct probe responded
Oct 11 13:20:06 kernel: [ 1457.293469] wlan0: authenticate with AP 00:02:cf:6a:32:c8
Oct 11 13:20:06 kernel: [ 1457.297005] wlan0: authenticated
Oct 11 13:20:06 kernel: [ 1457.297009] wlan0: associate with AP 00:02:cf:6a:32:c8
Oct 11 13:20:06 kernel: [ 1457.300763] wlan0: RX ReassocResp from 00:02:cf:6a:32:c8 (capab=0x471 status=0 aid=3)
Oct 11 13:20:06 kernel: [ 1457.300767] wlan0: associated
Oct 11 13:20:18 kernel: [ 1469.293498] wlan0: deauthenticated (Reason: 1)
Oct 11 13:20:19 kernel: [ 1470.292009] wlan0: direct probe to AP 00:02:cf:6a:32:c8 try 1
Oct 11 13:20:19 kernel: [ 1470.293575] wlan0 direct probe responded
Oct 11 13:20:19 kernel: [ 1470.293579] wlan0: authenticate with AP 00:02:cf:6a:32:c8
Oct 11 13:20:19 kernel: [ 1470.297215] wlan0: authenticated
Oct 11 13:20:19 kernel: [ 1470.297219] wlan0: associate with AP 00:02:cf:6a:32:c8
Oct 11 13:20:19 kernel: [ 1470.301055] wlan0: RX ReassocResp from 00:02:cf:6a:32:c8 (capab=0x471 status=0 aid=3)
Oct 11 13:20:19 kernel: [ 1470.301059] wlan0: associated
Oct 11 13:20:26 kernel: [ 1476.693463] wlan0: deauthenticating by local choice (reason=3)
Oct 11 13:20:26 kernel: [ 1476.694223] wlan0: deauthenticating by local choice (reason=3)
Oct 11 13:20:37 kernel: [ 1487.476011] usb 1-2: new high speed USB device using ehci_hcd and address 5
Oct 11 13:20:37 kernel: [ 1487.608895] usb 1-2: New USB device found, idVendor=1e3d, idProduct=2092
Oct 11 13:20:37 kernel: [ 1487.608899] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
Oct 11 13:20:37 kernel: [ 1487.608903] usb 1-2: Product: Flash Disk
Oct 11 13:20:37 kernel: [ 1487.608907] usb 1-2: Manufacturer: CBM
Oct 11 13:20:37 kernel: [ 1487.608910] usb 1-2: SerialNumber: CCCBB999988887777001156
Oct 11 13:20:37 kernel: [ 1487.609031] usb 1-2: configuration #1 chosen from 1 choice
Oct 11 13:20:37 kernel: [ 1487.611556] scsi3 : SCSI emulation for USB Mass Storage devices
Oct 11 13:20:37 kernel: [ 1487.613572] usb-storage: device found at 5
Oct 11 13:20:37 kernel: [ 1487.613575] usb-storage: waiting for device to settle before scanning
Oct 11 13:20:42 kernel: [ 1492.612184] usb-storage: device scan complete
Oct 11 13:20:42 kernel: [ 1492.612692] scsi 3:0:0:0: Direct-Access CBM Flash Disk 5.00 PQ: 0 ANSI: 2
Oct 11 13:20:42 kernel: [ 1492.616547] sd 3:0:0:0: [sdb] 8105984 512-byte hardware sectors: (4.15 GB/3.86 GiB)
Oct 11 13:20:42 kernel: [ 1492.617030] sd 3:0:0:0: [sdb] Write Protect is off
Oct 11 13:20:42 kernel: [ 1492.617035] sd 3:0:0:0: [sdb] Mode Sense: 0b 00 00 08
Oct 11 13:20:42 kernel: [ 1492.617039] sd 3:0:0:0: [sdb] Assuming drive cache: write through
Oct 11 13:20:42 kernel: [ 1492.618655] sd 3:0:0:0: [sdb] Assuming drive cache: write through
Oct 11 13:20:42 kernel: [ 1492.618662] sdb:
Oct 11 13:20:42 kernel: [ 1492.619480] sd 3:0:0:0: [sdb] Attached SCSI removable disk
Oct 11 13:20:43 kernel: [ 1493.575682] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
Oct 11 13:20:53 kernel: [ 1503.775981] usb 1-2: USB disconnect, address 5
Oct 11 13:39:21 kernel: [ 2611.836011] usb 1-2: new high speed USB device using ehci_hcd and address 6
Oct 11 13:39:21 kernel: [ 2611.968898] usb 1-2: New USB device found, idVendor=1e3d, idProduct=2092
Oct 11 13:39:21 kernel: [ 2611.968903] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
Oct 11 13:39:21 kernel: [ 2611.968907] usb 1-2: Product: Flash Disk
Oct 11 13:39:21 kernel: [ 2611.968910] usb 1-2: Manufacturer: CBM
Oct 11 13:39:21 kernel: [ 2611.968913] usb 1-2: SerialNumber: CCCBB999988887777001156
Oct 11 13:39:21 kernel: [ 2611.969028] usb 1-2: configuration #1 chosen from 1 choice
Oct 11 13:39:21 kernel: [ 2611.971525] scsi4 : SCSI emulation for USB Mass Storage devices
Oct 11 13:39:21 kernel: [ 2611.973505] usb-storage: device found at 6
Oct 11 13:39:21 kernel: [ 2611.973509] usb-storage: waiting for device to settle before scanning
Oct 11 13:39:26 kernel: [ 2616.972184] usb-storage: device scan complete
Oct 11 13:39:26 kernel: [ 2616.972696] scsi 4:0:0:0: Direct-Access CBM Flash Disk 5.00 PQ: 0 ANSI: 2
Oct 11 13:39:26 kernel: [ 2616.976549] sd 4:0:0:0: [sdb] 8105984 512-byte hardware sectors: (4.15 GB/3.86 GiB)
Oct 11 13:39:26 kernel: [ 2616.977035] sd 4:0:0:0: [sdb] Write Protect is off
Oct 11 13:39:26 kernel: [ 2616.977039] sd 4:0:0:0: [sdb] Mode Sense: 0b 00 00 08
Oct 11 13:39:26 kernel: [ 2616.977043] sd 4:0:0:0: [sdb] Assuming drive cache: write through
Oct 11 13:39:26 kernel: [ 2616.978658] sd 4:0:0:0: [sdb] Assuming drive cache: write through
Oct 11 13:39:26 kernel: [ 2616.978663] sdb:
Oct 11 13:39:26 kernel: [ 2616.979484] sd 4:0:0:0: [sdb] Attached SCSI removable disk
Oct 11 13:39:28 kernel: [ 2619.214720] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
regards,
Marcin
[1] It takes a lot of time and effort, because:
a) my laptop screen is broken, just about 20% of screen area is visible
b) because of (a), I have to use an external monitor
c) the external monitor socket and usb socket are placed in such way,
that it's impossible to have them both in use at the same time.
d) in many cases, when I unplug the USB stick to plug the monitor in
(to see what's going on), the installer does not like it, and
subsequently refuses to read the USB stick, so I have to start
from scratch
--
Marcin Owsiany <porridge@debian.org> http://marcin.owsiany.pl/
GnuPG: 1024D/60F41216 FE67 DA2D 0ACA FC5E 3F75 D6F6 3A0D 8AA0 60F4 1216
Reply to: