Bug#547270: linux-image-2.6.26-2-686: laptop does not power off after a 'halt'
Package: linux-image-2.6.26-2-686
Version: 2.6.26-19
Severity: normal
hi,
I just installed lenny on my laptop (NEC Versa P8210). When I do a
halt, the machine goes through the usual shutdown procedure, but
finishes with
[ some numbers ] Power Off
(or something like that, I can't remember exactly). But the machine
does not power off. dmesg appears to show ACPI loaded OK.
I tried booting with acpi=ht, and acpi=off, but the machine doesn't
even boot (I can write down those messages for you if you need them).
This is a dual core machine, with flgrx module loaded, and iwl3945 for
wireless.
I can give you more info if you need, but it looks like 'reportbug'
has appended lots of stuff.
Thanks very much
Matt
-- Package-specific info:
** Version:
Linux version 2.6.26-2-686 (Debian 2.6.26-19) (dannf@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 SMP Wed Aug 19 06:06:52 UTC 2009
** Command line:
root=/dev/mapper/vg-root ro
** Tainted: P (1)
** Kernel log:
[ 29.193571] [fglrx] Reserved FB block: Unshared offset:7ffb000, size:5000
[ 60.800700] CPU0 attaching NULL sched-domain.
[ 60.800715] CPU1 attaching NULL sched-domain.
[ 60.805541] CPU0 attaching sched-domain:
[ 60.805550] domain 0: span 0-1
[ 60.805555] groups: 0 1
[ 60.805563] CPU1 attaching sched-domain:
[ 60.805567] domain 0: span 0-1
[ 60.805571] groups: 1 0
[ 188.413614] CE: hpet increasing min_delta_ns to 15000 nsec
[ 211.204513] [fglrx] It's not necessary to adjust system aperture on this ASIC
[ 301.148261] Clocksource tsc unstable (delta = -76081519 ns)
[ 324.695803] [fglrx] It's not necessary to adjust system aperture on this ASIC
[ 338.843181] CPU0 attaching NULL sched-domain.
[ 338.843191] CPU1 attaching NULL sched-domain.
[ 338.868356] CPU0 attaching sched-domain:
[ 338.868365] domain 0: span 0-1
[ 338.868367] groups: 0 1
[ 338.868372] CPU1 attaching sched-domain:
[ 338.868375] domain 0: span 0-1
[ 338.868377] groups: 1 0
[ 4774.061635] eth0: no IPv6 routers present
[ 4853.202303] ACPI: PCI interrupt for device 0000:03:00.0 disabled
[ 4854.243973] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 4854.244155] PM: Writing back config space on device 0000:03:00.0 at offset 1 (was 100002, writing 100006)
[ 4854.291483] Registered led device: iwl-phy0:radio
[ 4854.291568] Registered led device: iwl-phy0:assoc
[ 4854.291602] Registered led device: iwl-phy0:RX
[ 4854.291634] Registered led device: iwl-phy0:TX
[ 4854.299045] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 4854.329345] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4854.332157] e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
[ 4854.332539] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 4868.401186] eth0: no IPv6 routers present
[ 4910.092370] eth0: no IPv6 routers present
[ 4984.440319] wlan0: Initial auth_alg=0
[ 4984.440319] wlan0: authenticate with AP 00:17:9a:1c:f0:6e
[ 4984.442201] wlan0: RX authentication from 00:17:9a:1c:f0:6e (alg=0 transaction=2 status=0)
[ 4984.442201] wlan0: authenticated
[ 4984.442201] wlan0: associate with AP 00:17:9a:1c:f0:6e
[ 4984.444299] wlan0: RX AssocResp from 00:17:9a:1c:f0:6e (capab=0x471 status=0 aid=1)
[ 4984.444299] wlan0: associated
[ 4984.444299] wlan0: switched to short barker preamble (BSSID=00:17:9a:1c:f0:6e)
[ 4984.444299] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 4998.845390] wlan0: no IPv6 routers present
[ 5019.050951] wlan0: deauthenticate(reason=3)
[ 5020.067559] wlan0: deauthentication frame received from unknown AP (SA=00:17:9a:1c:f0:6e BSSID=00:17:9a:1c:f0:6e) - ignored
[ 5020.067559] wlan0: deauthentication frame received from unknown AP (SA=00:17:9a:1c:f0:6e BSSID=00:17:9a:1c:f0:6e) - ignored
[ 5020.067559] wlan0: No STA entry for own AP 00:00:00:00:00:00
[ 5020.279498] ACPI: PCI interrupt for device 0000:03:00.0 disabled
[ 5029.763581] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 5029.763746] PM: Writing back config space on device 0000:03:00.0 at offset 1 (was 100002, writing 100006)
[ 5029.807180] Registered led device: iwl-phy0:radio
[ 5029.807264] Registered led device: iwl-phy0:assoc
[ 5029.807316] Registered led device: iwl-phy0:RX
[ 5029.807348] Registered led device: iwl-phy0:TX
[ 5029.824094] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 5035.482561] eth0: no IPv6 routers present
[ 5084.540672] [fglrx] It's not necessary to adjust system aperture on this ASIC
[ 5195.031693] [fglrx] It's not necessary to adjust system aperture on this ASIC
[ 5260.479642] wlan0: Initial auth_alg=0
[ 5260.479642] wlan0: authenticate with AP 00:17:9a:1c:f0:6e
[ 5260.481048] wlan0: RX authentication from 00:17:9a:1c:f0:6e (alg=0 transaction=2 status=0)
[ 5260.481066] wlan0: authenticated
[ 5260.481074] wlan0: associate with AP 00:17:9a:1c:f0:6e
[ 5260.483744] wlan0: RX AssocResp from 00:17:9a:1c:f0:6e (capab=0x471 status=0 aid=1)
[ 5260.483744] wlan0: associated
[ 5260.483744] wlan0: switched to short barker preamble (BSSID=00:17:9a:1c:f0:6e)
[ 5260.483744] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 5278.821451] wlan0: no IPv6 routers present
[ 5345.429853] [fglrx] It's not necessary to adjust system aperture on this ASIC
[ 5375.351502] CPU0 attaching NULL sched-domain.
[ 5375.351502] CPU1 attaching NULL sched-domain.
[ 5375.383510] CPU0 attaching sched-domain:
[ 5375.383510] domain 0: span 0-1
[ 5375.383510] groups: 0 1
[ 5375.383510] CPU1 attaching sched-domain:
[ 5375.383510] domain 0: span 0-1
[ 5375.383510] groups: 1 0
[ 6050.507646] PPP generic driver version 2.4.2
[ 6050.614301] padlock: VIA PadLock Hash Engine not detected.
[ 6050.644935] PPP MPPE Compression module registered
[ 6572.792123] wlan0: deauthenticate(reason=3)
[ 6573.817691] wlan0: deauthentication frame received from unknown AP (SA=00:17:9a:1c:f0:6e BSSID=00:17:9a:1c:f0:6e) - ignored
[ 6573.817691] wlan0: deauthentication frame received from unknown AP (SA=00:17:9a:1c:f0:6e BSSID=00:17:9a:1c:f0:6e) - ignored
[ 6573.817691] wlan0: deauthentication frame received from unknown AP (SA=00:17:9a:1c:f0:6e BSSID=00:17:9a:1c:f0:6e) - ignored
[ 6573.817691] wlan0: No STA entry for own AP 00:00:00:00:00:00
[ 6574.030550] ACPI: PCI interrupt for device 0000:03:00.0 disabled
[ 6580.840205] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 6580.840377] PM: Writing back config space on device 0000:03:00.0 at offset 1 (was 100002, writing 100006)
[ 6580.886824] Registered led device: iwl-phy0:radio
[ 6580.886912] Registered led device: iwl-phy0:assoc
[ 6580.886924] Registered led device: iwl-phy0:RX
[ 6580.886924] Registered led device: iwl-phy0:TX
[ 6580.894503] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 6590.035074] eth0: no IPv6 routers present
[ 6604.730753] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 6604.733666] e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
[ 6604.735741] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 6620.939321] eth0: no IPv6 routers present
** Loaded modules:
Module Size Used by
ppp_async 7488 0
crc_ccitt 2080 1 ppp_async
sha1_generic 2304 0
ppp_mppe 5700 0
ppp_generic 20028 2 ppp_async,ppp_mppe
slhc 5408 1 ppp_generic
fglrx 1939196 21
rfcomm 28272 0
l2cap 17248 5 rfcomm
vboxnetadp 68008 0
vboxnetflt 73448 0
vboxdrv 103848 1 vboxnetflt
ppdev 6468 0
parport_pc 22500 0
lp 8164 0
parport 30988 3 ppdev,parport_pc,lp
ipv6 235396 24
acpi_cpufreq 6796 0
cpufreq_userspace 3172 0
cpufreq_powersave 1856 0
cpufreq_conservative 5960 0
cpufreq_stats 3776 0
cpufreq_ondemand 6476 2
freq_table 4224 3 acpi_cpufreq,cpufreq_stats,cpufreq_ondemand
sbp2 18572 0
loop 12748 0
joydev 8480 0
arc4 1824 2
ecb 2624 2
crypto_blkcipher 15236 1 ecb
snd_hda_intel 325688 0
snd_pcm_oss 32800 0
snd_mixer_oss 12320 1 snd_pcm_oss
iwl3945 78804 0
snd_pcm 62660 2 snd_hda_intel,snd_pcm_oss
firmware_class 6816 1 iwl3945
snd_seq_dummy 2660 0
mac80211 139776 1 iwl3945
pcspkr 2432 0
hci_usb 12252 2
led_class 3908 1 iwl3945
snd_seq_oss 24992 0
snd_seq_midi 5728 0
i2c_i801 7920 0
psmouse 32336 0
bluetooth 44996 7 rfcomm,l2cap,hci_usb
i2c_core 19828 1 i2c_i801
cfg80211 21608 2 iwl3945,mac80211
serio_raw 4740 0
rng_core 3940 0
snd_rawmidi 18496 1 snd_seq_midi
snd_seq_midi_event 6432 2 snd_seq_oss,snd_seq_midi
snd_seq 41456 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
video 16464 0
output 2912 1 video
snd_timer 17800 2 snd_pcm,snd_seq
snd_seq_device 6380 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
battery 10180 0
ac 4196 0
button 6096 0
snd 45636 9 snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
soundcore 6368 1 snd
snd_page_alloc 7816 2 snd_hda_intel,snd_pcm
intel_agp 22524 0
agpgart 28808 2 fglrx,intel_agp
evdev 8000 12
ext3 105576 5
jbd 39476 1 ext3
mbcache 7108 1 ext3
dm_mirror 15136 0
dm_log 8452 1 dm_mirror
dm_snapshot 14340 0
dm_mod 46216 12 dm_mirror,dm_log,dm_snapshot
sg 26964 0
sr_mod 13316 0
cdrom 30176 1 sr_mod
sd_mod 22200 4
ata_generic 4676 0
ata_piix 14180 3
libata 140448 2 ata_generic,ata_piix
scsi_mod 129548 5 sbp2,sg,sr_mod,sd_mod,libata
dock 8304 1 libata
sdhci 13060 0
mmc_core 39964 1 sdhci
e100 28908 0
mii 4896 1 e100
ohci1394 24976 0
ieee1394 75832 2 sbp2,ohci1394
ide_pci_generic 3908 0 [permanent]
ide_core 96168 1 ide_pci_generic
ehci_hcd 28428 0
uhci_hcd 18672 0
usbcore 118192 4 hci_usb,ehci_hcd,uhci_hcd
thermal 15228 0
processor 32576 4 acpi_cpufreq,thermal
fan 4196 0
thermal_sys 10856 4 video,thermal,processor,fan
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub [8086:27a0] (rev 03)
Subsystem: Device [1631:c017]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel modules: intel-agp
00:01.0 PCI bridge [0604]: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express PCI Express Root Port [8086:27a1] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00006000-00006fff
Memory behind bridge: 9c200000-9c2fffff
Prefetchable memory behind bridge: 0000000088000000-000000008fffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1b.0 Audio device [0403]: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller [8086:27d8] (rev 02)
Subsystem: Device [1631:c017]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at 9c300000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:1c.0 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 [8086:27d0] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00005000-00005fff
Memory behind bridge: 9b200000-9c1fffff
Prefetchable memory behind bridge: 0000000094100000-00000000950fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.1 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 [8086:27d2] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: 9a100000-9b1fffff
Prefetchable memory behind bridge: 0000000095100000-00000000960fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.2 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3 [8086:27d4] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: 99100000-9a0fffff
Prefetchable memory behind bridge: 0000000096100000-00000000970fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.3 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 4 [8086:27d6] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: 98100000-990fffff
Prefetchable memory behind bridge: 0000000097100000-00000000980fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1d.0 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 [8086:27c8] (rev 02) (prog-if 00 [UHCI])
Subsystem: Device [1631:c017]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at 7080 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 [8086:27c9] (rev 02) (prog-if 00 [UHCI])
Subsystem: Device [1631:c017]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at 7060 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 [8086:27ca] (rev 02) (prog-if 00 [UHCI])
Subsystem: Device [1631:c017]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 7040 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.3 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 [8086:27cb] (rev 02) (prog-if 00 [UHCI])
Subsystem: Device [1631:c017]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 19
Region 4: I/O ports at 7020 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller [8086:27cc] (rev 02) (prog-if 20 [EHCI])
Subsystem: Device [1631:c017]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at 9c304400 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=06, subordinate=07, sec-latency=32
I/O behind bridge: 00001000-00001fff
Memory behind bridge: 92000000-940fffff
Prefetchable memory behind bridge: 0000000090000000-0000000091ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR+
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge [8086:27b9] (rev 02)
Subsystem: Device [1631:c017]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel modules: iTCO_wdt, intel-rng
00:1f.2 IDE interface [0101]: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller [8086:27c4] (rev 02) (prog-if 80 [Master])
Subsystem: Device [1631:c017]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 70a0 [size=16]
Capabilities: <access denied>
Kernel driver in use: ata_piix
Kernel modules: ata_piix
00:1f.3 SMBus [0c05]: Intel Corporation 82801G (ICH7 Family) SMBus Controller [8086:27da] (rev 02)
Subsystem: Device [1631:c017]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at 7000 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801
01:00.0 VGA compatible controller [0300]: ATI Technologies Inc M56P [Radeon Mobility X1600] [1002:71c5] (prog-if 00 [VGA controller])
Subsystem: Device [1631:c017]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at 88000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 6000 [size=256]
Region 2: Memory at 9c200000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at 9c220000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: fglrx_pci
Kernel modules: fglrx
03:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection [8086:4222] (rev 02)
Subsystem: Intel Corporation PRO/Wireless 3945ABG Network Connection [8086:1000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 218
Region 0: Memory at 9a100000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: iwl3945
Kernel modules: iwl3945
06:02.0 FireWire (IEEE 1394) [0c00]: O2 Micro, Inc. Firewire (IEEE 1394) [1217:00f7] (rev 02) (prog-if 10 [OHCI])
Subsystem: Device [1631:c017]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 64
Interrupt: pin A routed to IRQ 16
Region 0: Memory at 94003000 (32-bit, non-prefetchable) [size=4K]
Region 1: Memory at 94004000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ohci1394
Kernel modules: ohci1394
06:02.2 SD Host controller [0805]: O2 Micro, Inc. Integrated MMC/SD Controller [1217:7120] (rev 01)
Subsystem: Device [1631:c017]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 16
Region 0: Memory at 94004800 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: sdhci
Kernel modules: sdhci
06:02.3 Mass storage controller [0180]: O2 Micro, Inc. Integrated MS/xD Controller [1217:7130] (rev 01)
Subsystem: Device [1631:c017]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 94001000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
06:08.0 Ethernet controller [0200]: Intel Corporation PRO/100 VE Network Connection [8086:1092] (rev 02)
Subsystem: Device [1631:c017]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (2000ns min, 14000ns max)
Interrupt: pin A routed to IRQ 20
Region 0: Memory at 94000000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 1200 [size=64]
Capabilities: <access denied>
Kernel driver in use: e100
Kernel modules: e100
-- System Information:
Debian Release: 5.0.3
APT prefers stable
APT policy: (500, 'stable')
Architecture: i386 (i686)
Kernel: Linux 2.6.26-2-686 (SMP w/2 CPU cores)
Locale: LANG=C, LC_CTYPE=C (charmap=ANSI_X3.4-1968)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.26-2-686 depends on:
ii debconf [debconf-2.0] 1.5.24 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92o tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.26-2-686 recommends:
ii libc6-i686 2.7-18 GNU C Library: Shared libraries [i
Versions of packages linux-image-2.6.26-2-686 suggests:
ii grub 0.97-47lenny2 GRand Unified Bootloader (Legacy v
pn linux-doc-2.6.26 <none> (no description available)
-- debconf information:
linux-image-2.6.26-2-686/postinst/bootloader-error-2.6.26-2-686:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.26-2-686/postinst/old-dir-initrd-link-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/overwriting-modules-2.6.26-2-686: true
linux-image-2.6.26-2-686/postinst/bootloader-test-error-2.6.26-2-686:
linux-image-2.6.26-2-686/postinst/depmod-error-2.6.26-2-686: false
linux-image-2.6.26-2-686/preinst/bootloader-initrd-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/abort-overwrite-2.6.26-2-686:
linux-image-2.6.26-2-686/preinst/abort-install-2.6.26-2-686:
linux-image-2.6.26-2-686/postinst/depmod-error-initrd-2.6.26-2-686: false
linux-image-2.6.26-2-686/postinst/create-kimage-link-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/failed-to-move-modules-2.6.26-2-686:
linux-image-2.6.26-2-686/preinst/initrd-2.6.26-2-686:
linux-image-2.6.26-2-686/preinst/lilo-has-ramdisk:
linux-image-2.6.26-2-686/prerm/would-invalidate-boot-loader-2.6.26-2-686: true
linux-image-2.6.26-2-686/postinst/kimage-is-a-directory:
linux-image-2.6.26-2-686/postinst/old-initrd-link-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/elilo-initrd-2.6.26-2-686: true
linux-image-2.6.26-2-686/preinst/lilo-initrd-2.6.26-2-686: true
linux-image-2.6.26-2-686/prerm/removing-running-kernel-2.6.26-2-686: true
linux-image-2.6.26-2-686/postinst/old-system-map-link-2.6.26-2-686: true
Reply to: