Bug#544709: linux-image-2.6.30-1-686: /proc/acpi/button/lid/*/state always says "open"
Package: linux-image-2.6.30-1-686
Version: 2.6.30-6
Severity: normal
My laptop is an HP 530
After a cold boot, regardless of whether my laptop lid is open or closed, I always get this:
# cat /proc/acpi/button/lid/*/state
state: open
Strangely, after a cold boot, doing a hibernate manually from gnome and then waking the machine causes the lid switch to start to work correctly.
--Kernel log after hibernate and waking the machine:
http://jmaslibre.org/kernel-info/kern.log
-- Package-specific info:
** Version:
Linux version 2.6.30-1-686 (Debian 2.6.30-6) (waldi@debian.org) (gcc version 4.3.4 (Debian 4.3.4-1) ) #1 SMP Sat Aug 15 19:11:58 UTC 2009
** Command line:
BOOT_IMAGE=/boot/vmlinuz-2.6.30-1-686 root=UUID=392f401e-e849-4d62-9609-1e6318f75848 ro quiet video=intelfb vga=792
** Not tainted
** Kernel log:
[ 3.142508] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 filtered out
[ 3.143277] ata1.00: configured for UDMA/100
[ 3.157766] ata1.00: configured for UDMA/100
[ 3.157770] ata1: EH complete
[ 3.157891] scsi 0:0:0:0: Direct-Access ATA ST980811AS 3.BH PQ: 0 ANSI: 5
[ 3.169626] ide-cd driver 5.00
[ 3.170954] ide-cd: hda: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache
[ 3.170962] Uniform CD-ROM driver Revision: 3.20
[ 3.197502] Driver 'sd' needs updating - please use bus_type methods
[ 3.197659] sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors: (80.0 GB/74.5 GiB)
[ 3.197678] sd 0:0:0:0: [sda] Write Protect is off
[ 3.197682] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.197708] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.197819] sda: sda1 sda3 sda4 < sda5 sda6 >
[ 3.245464] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.813914] PM: Starting manual resume from disk
[ 3.891133] kjournald starting. Commit interval 5 seconds
[ 3.891145] EXT3-fs: mounted filesystem with ordered data mode.
[ 6.405454] udev: starting version 141
[ 7.609938] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 7.609947] ACPI: Power Button [PWRF]
[ 7.610045] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input3
[ 7.610050] ACPI: Sleep Button [C20B]
[ 7.610110] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input4
[ 7.610232] ACPI: Lid Switch [C20C]
[ 7.621520] ACPI: AC Adapter [C1AB] (off-line)
[ 7.676069] input: PC Speaker as /devices/platform/pcspkr/input/input5
[ 7.687973] ACPI Warning (processor_throttling-0843): Invalid throttling state, reset [20090320]
[ 7.688422] Marking TSC unstable due to TSC halts in idle
[ 7.688495] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 7.688550] processor ACPI_CPU:00: registered as cooling_device5
[ 7.688556] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 7.723277] ACPI: Battery Slot [C1AC] (battery present)
[ 7.724441] ACPI: WMI: Mapper loaded
[ 7.757338] intel_rng: FWH not detected
[ 7.947538] cfg80211: Using static regulatory domain info
[ 7.947542] cfg80211: Regulatory domain: US
[ 7.947544] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 7.947548] (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
[ 7.947552] (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 7.947555] (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 7.947559] (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 7.947562] (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 7.947566] (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
[ 7.947576] cfg80211: Calling CRDA for country: US
[ 7.996426] yenta_cardbus 0000:02:06.0: CardBus bridge found [103c:30d5]
[ 7.996454] yenta_cardbus 0000:02:06.0: Using CSCINT to route CSC interrupts to PCI
[ 7.996457] yenta_cardbus 0000:02:06.0: Routing CardBus interrupts to PCI
[ 7.996464] yenta_cardbus 0000:02:06.0: TI: mfunc 0x01be1b32, devctl 0x44
[ 8.050729] Synaptics Touchpad, model: 1, fw: 6.3, id: 0x1a0b1, caps: 0xa04713/0x200000
[ 8.090261] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input6
[ 8.235761] yenta_cardbus 0000:02:06.0: ISA IRQ mask 0x0cf8, PCI irq 18
[ 8.235767] yenta_cardbus 0000:02:06.0: Socket status: 30000006
[ 8.235772] pci_bus 0000:02: Raising subordinate bus# of parent bus (#02) from #03 to #06
[ 8.235783] yenta_cardbus 0000:02:06.0: pcmcia: parent PCI bridge I/O window: 0x2000 - 0x2fff
[ 8.235787] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x2000-0x2fff: clean.
[ 8.236038] yenta_cardbus 0000:02:06.0: pcmcia: parent PCI bridge Memory window: 0xf0100000 - 0xf03fffff
[ 8.236043] yenta_cardbus 0000:02:06.0: pcmcia: parent PCI bridge Memory window: 0x60000000 - 0x63ffffff
[ 8.654932] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: clean.
[ 8.657029] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: clean.
[ 8.658049] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: clean.
[ 8.658764] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: clean.
[ 8.659657] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
[ 8.684815] b43-phy0: Broadcom 4311 WLAN found (core revision 10)
[ 8.773789] HDA Intel 0000:00:1b.0: power state changed by ACPI to D0
[ 8.773802] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 8.773850] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 8.860553] phy0: Selected rate control algorithm 'minstrel'
[ 8.861281] Broadcom 43xx driver loaded [ Features: PMLR, Firmware-ID: FW13 ]
[ 9.870739] Adding 1445808k swap on /dev/sda6. Priority:-1 extents:1 across:1445808k
[ 10.050353] EXT3 FS on sda5, internal journal
[ 10.368620] loop: module loaded
[ 10.418979] vboxdrv: Trying to deactivate the NMI watchdog permanently...
[ 10.418983] vboxdrv: Successfully done.
[ 10.418985] vboxdrv: Found 1 processor cores.
[ 10.419091] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[ 10.419093] vboxdrv: Successfully loaded version 3.0.2_OSE (interface 0x000e0000).
[ 10.524841] device-mapper: uevent: version 1.0.3
[ 10.526002] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[ 11.266830] REISERFS (device sda1): found reiserfs format "3.6" with standard journal
[ 11.266882] REISERFS (device sda1): using ordered data mode
[ 11.273607] REISERFS (device sda1): journal params: device sda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 11.273963] REISERFS (device sda1): checking transaction log (sda1)
[ 11.318122] REISERFS (device sda1): Using r5 hash to sort names
[ 16.383688] apm: BIOS not found.
[ 27.500046] Clocksource tsc unstable (delta = -454522142 ns)
[ 39.646822] lp: driver loaded but no devices found
[ 39.819237] ppdev: user-space parallel port driver
[ 40.438041] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 41.472588] [drm] Initialized drm 1.1.0 20060810
[ 41.524330] pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 41.524337] pci 0000:00:02.0: setting latency timer to 64
[ 41.527034] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 207.288743] CPU0 attaching NULL sched-domain.
[ 207.288790] CPU0 attaching NULL sched-domain.
[ 218.993385] UDF-fs: Partition marked readonly; forcing readonly mount
[ 219.043175] UDF-fs INFO UDF: Mounting volume 'Milk-ITL2.0', timestamp 2009/03/14 13:54 (1e98)
[ 256.816163] e100: eth0 NIC Link is Up 100 Mbps Full Duplex
[ 256.816479] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 267.044046] eth0: no IPv6 routers present
** Loaded modules:
Module Size Used by
isofs 27592 0
udf 67284 1
nls_base 6416 2 isofs,udf
crc_itu_t 2148 1 udf
i915 147544 1
drm 137920 2 i915
i2c_algo_bit 4860 1 i915
i2c_core 20844 3 i915,drm,i2c_algo_bit
ppdev 6348 0
parport_pc 22420 0
lp 8012 0
parport 31144 3 ppdev,parport_pc,lp
cpufreq_conservative 6256 0
cpufreq_powersave 1292 0
cpufreq_stats 3520 0
cpufreq_userspace 2768 0
reiserfs 187592 1
dm_snapshot 21604 0
dm_mirror 12580 0
dm_region_hash 10668 1 dm_mirror
dm_log 8464 2 dm_mirror,dm_region_hash
dm_mod 49992 3 dm_snapshot,dm_mirror,dm_log
vboxdrv 102480 0
loop 13324 0
arc4 1560 2
snd_hda_codec_conexant 17164 1
ecb 2368 2
snd_hda_intel 22192 2
snd_hda_codec 63580 2 snd_hda_codec_conexant,snd_hda_intel
snd_hwdep 6120 1 snd_hda_codec
snd_pcm_oss 32232 0
b43 108932 0
snd_mixer_oss 12368 1 snd_pcm_oss
snd_pcm 62420 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss
snd_seq_midi 5688 0
rfkill 9668 1 b43
snd_rawmidi 18596 1 snd_seq_midi
joydev 8576 0
mac80211 142848 1 b43
snd_seq_midi_event 6212 1 snd_seq_midi
yenta_socket 21168 1
rsrc_nonstatic 9664 1 yenta_socket
cfg80211 55556 2 b43,mac80211
snd_seq 42436 2 snd_seq_midi,snd_seq_midi_event
led_class 3852 1 b43
snd_timer 17436 2 snd_pcm,snd_seq
psmouse 37528 0
snd_seq_device 6136 3 snd_seq_midi,snd_rawmidi,snd_seq
rng_core 3672 1 b43
wmi 6184 0
serio_raw 4560 0
input_polldev 3588 1 b43
evdev 8028 15
pcspkr 2104 0
container 3244 0
processor 34504 1
battery 6012 0
ac 2960 0
button 5060 0
snd 49060 15 snd_hda_codec_conexant,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
soundcore 6184 1 snd
snd_page_alloc 8180 2 snd_hda_intel,snd_pcm
ext3 107172 1
jbd 41036 1 ext3
mbcache 6924 1 ext3
sd_mod 28748 4
crc_t10dif 1632 1 sd_mod
ide_cd_mod 24484 1
cdrom 30316 1 ide_cd_mod
ide_pci_generic 3632 0
uhci_hcd 19132 0
ata_generic 4340 0
ahci 30068 3
libata 150904 2 ata_generic,ahci
ehci_hcd 29680 0
piix 5680 1
e100 27464 0
mii 4664 1 e100
usbcore 126004 3 uhci_hcd,ehci_hcd
ide_core 88100 3 ide_cd_mod,ide_pci_generic,piix
scsi_mod 131800 2 sd_mod,libata
ssb 37692 1 b43
pcmcia 24280 2 b43,ssb
pcmcia_core 31212 5 b43,yenta_socket,rsrc_nonstatic,ssb,pcmcia
intel_agp 22900 1
agpgart 30836 3 drm,intel_agp
video 18044 1 i915
output 2604 1 video
thermal 12580 0
fan 4044 0
thermal_sys 13140 4 processor,video,thermal,fan
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub [8086:27a0] (rev 03)
Subsystem: Hewlett-Packard Company Device [103c:30d5]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller [8086:27a2] (rev 03) (prog-if 00 [VGA controller])
Subsystem: Hewlett-Packard Company Device [103c:30d5]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f0400000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at 3000 [size=8]
Region 2: Memory at e0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at f0480000 (32-bit, non-prefetchable) [size=256K]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
00:02.1 Display controller [0380]: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller [8086:27a6] (rev 03)
Subsystem: Hewlett-Packard Company Device [103c:30d5]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at f0500000 (32-bit, non-prefetchable) [size=512K]
Capabilities: <access denied>
00:1b.0 Audio device [0403]: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller [8086:27d8] (rev 01)
Subsystem: Hewlett-Packard Company Device [103c:30d5]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f0580000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
00:1c.0 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 [8086:27d0] (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=08, subordinate=08, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1c.1 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 [8086:27d2] (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=10, subordinate=10, sec-latency=0
Memory behind bridge: f0000000-f00fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1d.0 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 [8086:27c8] (rev 01) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:30d5]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 3020 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller [8086:27cc] (rev 01) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Device [103c:30d5]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 0: Memory at f0584000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e1) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=06, sec-latency=32
I/O behind bridge: 00002000-00002fff
Memory behind bridge: f0100000-f03fffff
Prefetchable memory behind bridge: 0000000060000000-0000000063ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge [8086:27b9] (rev 01)
Subsystem: Hewlett-Packard Company Device [103c:30d5]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.1 IDE interface [0101]: Intel Corporation 82801G (ICH7 Family) IDE Controller [8086:27df] (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: Hewlett-Packard Company Device [103c:30d5]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 3040 [size=16]
Kernel driver in use: PIIX_IDE
00:1f.2 SATA controller [0106]: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA AHCI Controller [8086:27c5] (rev 01) (prog-if 01 [AHCI 1.0])
Subsystem: Hewlett-Packard Company Device [103c:30d5]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 26
Region 0: I/O ports at 13f0 [size=8]
Region 1: I/O ports at 15f4 [size=4]
Region 2: I/O ports at 1370 [size=8]
Region 3: I/O ports at 1574 [size=4]
Region 4: I/O ports at 3070 [size=16]
Region 5: Memory at f0585000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ahci
02:06.0 CardBus bridge [0607]: ENE Technology Inc CB1410 Cardbus Controller [1524:1410] (rev 01)
Subsystem: Hewlett-Packard Company Device [103c:30d5]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at f0100000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
Memory window 0: 60000000-63fff000 (prefetchable)
Memory window 1: 64000000-67fff000
I/O window 0: 00002400-000024ff
I/O window 1: 00002800-000028ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
02:08.0 Ethernet controller [0200]: Intel Corporation 82562ET/EZ/GT/GZ - PRO/100 VE (LOM) Ethernet Controller Mobile [8086:1068] (rev 01)
Subsystem: Hewlett-Packard Company Device [103c:30d5]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (2000ns min, 14000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 20
Region 0: Memory at f0101000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 2000 [size=64]
Capabilities: <access denied>
Kernel driver in use: e100
10:00.0 Network controller [0280]: Broadcom Corporation BCM4311 802.11b/g WLAN [14e4:4311] (rev 01)
Subsystem: Hewlett-Packard Company BCM4311 802.11b/g Wireless LAN Controller [103c:1364]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at f0000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: b43-pci-bridge
-- System Information:
Debian Release: squeeze/sid
APT prefers unstable
APT policy: (500, 'unstable')
Architecture: i386 (i686)
Kernel: Linux 2.6.30-1-686 (SMP w/1 CPU core)
Locale: LANG=es_GT.UTF-8, LC_CTYPE=es_GT.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.30-1-686 depends on:
ii debconf [debconf-2.0] 1.5.27 Debian configuration management sy
ii initramfs-tools [linux-initra 0.93.4 tools for generating an initramfs
ii module-init-tools 3.9-2 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.30-1-686 recommends:
ii libc6-i686 2.9-25 GNU C Library: Shared libraries [i
Versions of packages linux-image-2.6.30-1-686 suggests:
ii grub-pc [grub] 1.96+20090808-1 GRand Unified Bootloader, version
pn linux-doc-2.6.30 <none> (no description available)
-- debconf information:
linux-image-2.6.30-1-686/preinst/lilo-has-ramdisk:
linux-image-2.6.30-1-686/postinst/create-kimage-link-2.6.30-1-686: true
linux-image-2.6.30-1-686/prerm/would-invalidate-boot-loader-2.6.30-1-686: true
linux-image-2.6.30-1-686/preinst/overwriting-modules-2.6.30-1-686: true
linux-image-2.6.30-1-686/postinst/old-dir-initrd-link-2.6.30-1-686: true
linux-image-2.6.30-1-686/preinst/failed-to-move-modules-2.6.30-1-686:
linux-image-2.6.30-1-686/preinst/initrd-2.6.30-1-686:
linux-image-2.6.30-1-686/prerm/removing-running-kernel-2.6.30-1-686: true
linux-image-2.6.30-1-686/postinst/kimage-is-a-directory:
linux-image-2.6.30-1-686/preinst/abort-overwrite-2.6.30-1-686:
linux-image-2.6.30-1-686/preinst/bootloader-initrd-2.6.30-1-686: true
linux-image-2.6.30-1-686/postinst/depmod-error-initrd-2.6.30-1-686: false
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.30-1-686/postinst/old-initrd-link-2.6.30-1-686: true
linux-image-2.6.30-1-686/postinst/depmod-error-2.6.30-1-686: false
linux-image-2.6.30-1-686/postinst/old-system-map-link-2.6.30-1-686: true
linux-image-2.6.30-1-686/preinst/lilo-initrd-2.6.30-1-686: true
linux-image-2.6.30-1-686/postinst/bootloader-test-error-2.6.30-1-686:
linux-image-2.6.30-1-686/preinst/abort-install-2.6.30-1-686:
linux-image-2.6.30-1-686/postinst/bootloader-error-2.6.30-1-686:
linux-image-2.6.30-1-686/preinst/elilo-initrd-2.6.30-1-686: true
Reply to: