Package: linux-image-2.6.30-1-powerpc Version: 2.6.30-6 Severity: normal Hi, I have a raid1 between two PATA disks, and one of them failed during an array check; as these are consumer disks (Maxtor 5A300J0), these are somewhat reluctant to report hard errors but rather retry when asked, so the array did not kick the disk out (which is probably a bug in itself). After manually setting the disk as "failed", the kernel went into a loop trying to resync the array, even though there is no spare available, which then immediately fails and is retried. During this, the amount of nonshared pages in the system steadily increased, and the system was in iowait state most of the time (see attached graphs). Removing the disk from the array is not possible because it is "busy"; neither is decreasing the number of RAID disks. Simon -- Package-specific info: ** Version: Linux version 2.6.30-1-powerpc (Debian 2.6.30-6) (waldi@debian.org) (gcc version 4.3.4 (Debian 4.3.4-1) ) #1 Sat Aug 15 16:56:55 CEST 2009 ** Command line: root=/dev/mapper/honey-root console=ttyS0,115200 ** Not tainted ** Kernel log: [89926.824444] RAID1 conf printout: [89926.827748] --- wd:1 rd:2 [89926.830542] disk 0, wo:0, o:1, dev:hdc [89926.834471] disk 1, wo:1, o:0, dev:hda [89926.891833] md: recovery of RAID array md0 [89926.896036] md: minimum _guaranteed_ speed: 1000 KB/sec/disk. [89926.901984] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for recovery. [89926.911751] md: using 128k window, over a total of 292970048 blocks. [89926.918322] md: resuming recovery of md0 from checkpoint. [89926.923968] md: md0: recovery done. [89926.979286] RAID1 conf printout: [89926.982599] --- wd:1 rd:2 [89926.985376] disk 0, wo:0, o:1, dev:hdc [89926.989298] disk 1, wo:1, o:0, dev:hda [89927.076764] md: recovery of RAID array md0 [89927.081138] md: minimum _guaranteed_ speed: 1000 KB/sec/disk. [89927.087103] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for recovery. [89927.096881] md: using 128k window, over a total of 292970048 blocks. [89927.103369] md: resuming recovery of md0 from checkpoint. [89927.108890] md: md0: recovery done. [89927.157002] RAID1 conf printout: [89927.160327] --- wd:1 rd:2 [89927.163090] disk 0, wo:0, o:1, dev:hdc [89927.167019] disk 1, wo:1, o:0, dev:hda [89927.260544] md: recovery of RAID array md0 [89927.264817] md: minimum _guaranteed_ speed: 1000 KB/sec/disk. [89927.270775] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for recovery. [89927.280530] md: using 128k window, over a total of 292970048 blocks. [89927.287009] md: resuming recovery of md0 from checkpoint. [89927.292775] md: md0: recovery done. [89927.340217] RAID1 conf printout: [89927.343537] --- wd:1 rd:2 [89927.346328] disk 0, wo:0, o:1, dev:hdc [89927.350263] disk 1, wo:1, o:0, dev:hda [89927.361548] md: recovery of RAID array md0 [89927.366125] md: minimum _guaranteed_ speed: 1000 KB/sec/disk. [89927.372122] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for recovery. [89927.381881] md: using 128k window, over a total of 292970048 blocks. [89927.388616] md: resuming recovery of md0 from checkpoint. [89927.394140] md: md0: recovery done. [89927.445778] RAID1 conf printout: [89927.449105] --- wd:1 rd:2 [89927.451889] disk 0, wo:0, o:1, dev:hdc [89927.455820] disk 1, wo:1, o:0, dev:hda [89927.489265] md: recovery of RAID array md0 [89927.493757] md: minimum _guaranteed_ speed: 1000 KB/sec/disk. [89927.499726] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for recovery. [89927.509493] md: using 128k window, over a total of 292970048 blocks. [89927.515987] md: resuming recovery of md0 from checkpoint. [89927.521507] md: md0: recovery done. [89927.567953] RAID1 conf printout: [89927.571412] --- wd:1 rd:2 [89927.574216] disk 0, wo:0, o:1, dev:hdc [89927.578139] disk 1, wo:1, o:0, dev:hda [89927.596430] md: recovery of RAID array md0 [89927.600739] md: minimum _guaranteed_ speed: 1000 KB/sec/disk. [89927.606722] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for recovery. [89927.616494] md: using 128k window, over a total of 292970048 blocks. [89927.622979] md: resuming recovery of md0 from checkpoint. [89927.628744] md: md0: recovery done. [89927.667979] RAID1 conf printout: [89927.671304] --- wd:1 rd:2 [89927.674101] disk 0, wo:0, o:1, dev:hdc [89927.678034] disk 1, wo:1, o:0, dev:hda [89927.695936] md: recovery of RAID array md0 [89927.700179] md: minimum _guaranteed_ speed: 1000 KB/sec/disk. [89927.706134] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for recovery. [89927.715897] md: using 128k window, over a total of 292970048 blocks. [89927.722382] md: resuming recovery of md0 from checkpoint. [89927.727902] md: md0: recovery done. [89927.769115] RAID1 conf printout: [89927.772442] --- wd:1 rd:2 [89927.775198] disk 0, wo:0, o:1, dev:hdc [89927.779122] disk 1, wo:1, o:0, dev:hda [89927.796836] md: recovery of RAID array md0 [89927.801140] md: minimum _guaranteed_ speed: 1000 KB/sec/disk. [89927.807104] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for recovery. [89927.816879] md: using 128k window, over a total of 292970048 blocks. [89927.823364] md: resuming recovery of md0 from checkpoint. [89927.828882] md: md0: recovery done. [89927.868153] RAID1 conf printout: [89927.871459] --- wd:1 rd:2 [89927.874251] disk 0, wo:0, o:1, dev:hdc [89927.878173] disk 1, wo:1, o:0, dev:hda [89927.891380] md: recovery of RAID array md0 [89927.895603] md: minimum _guaranteed_ speed: 1000 KB/sec/disk. [89927.901602] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for recovery. [89927.911389] md: using 128k window, over a total of 292970048 blocks. [89927.917868] md: resuming recovery of md0 from checkpoint. [89927.923388] md: md0: recovery done. [89927.978865] RAID1 conf printout: [89927.982178] --- wd:1 rd:2 [89927.984952] disk 0, wo:0, o:1, dev:hdc [89927.988866] disk 1, wo:1, o:0, dev:hda [89928.007398] md: recovery of RAID array md0 [89928.011734] md: minimum _guaranteed_ speed: 1000 KB/sec/disk. [89928.017703] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for recovery. [89928.027481] md: using 128k window, over a total of 292970048 blocks. [89928.033979] md: resuming recovery of md0 from checkpoint. [89928.039489] md: md0: recovery done. ** Loaded modules: Module Size Used by cls_fw 8804 2 sch_sfq 10036 1 sch_htb 20028 1 sit 15232 0 tunnel4 6908 1 sit 8021q 26644 0 garp 12112 1 8021q pppoe 16296 2 pppox 6780 1 pppoe ppp_generic 30564 6 pppoe,pppox slhc 9548 1 ppp_generic binfmt_misc 12616 1 bridge 55852 0 stp 6088 2 garp,bridge bnep 17188 2 sco 14296 2 l2cap 25908 3 bnep bluetooth 62032 5 bnep,sco,l2cap tun 17728 12 deflate 6404 0 zlib_deflate 24144 1 deflate ctr 8132 0 twofish 10472 0 twofish_common 18000 1 twofish camellia 23616 0 serpent 25008 0 blowfish 12464 0 des_generic 22660 0 xcbc 8972 0 rmd160 12624 0 sha1_generic 5844 0 hmac 7908 0 crypto_null 6636 0 af_key 35208 2 ipt_MASQUERADE 6224 7 iptable_nat 9788 1 nf_nat 21882 2 ipt_MASQUERADE,iptable_nat xt_length 5152 2 xt_TCPMSS 7588 1 xt_owner 6076 1 xt_MARK 5492 3 iptable_mangle 7200 1 xt_recent 13148 2 xt_tcpudp 6448 2 nf_conntrack_ipv4 17932 4 iptable_nat,nf_nat nf_defrag_ipv4 5400 1 nf_conntrack_ipv4 xt_state 5532 1 nf_conntrack 71980 5 ipt_MASQUERADE,iptable_nat,nf_nat,nf_conntrack_ipv4,xt_state iptable_filter 6804 1 ip_tables 16028 3 iptable_nat,iptable_mangle,iptable_filter x_tables 20068 10 ipt_MASQUERADE,iptable_nat,xt_length,xt_TCPMSS,xt_owner,xt_MARK,xt_recent,xt_tcpudp,xt_state,ip_tables snd_via82xx 30584 0 gameport 15128 1 snd_via82xx snd_mpu401_uart 11392 1 snd_via82xx snd_seq_midi 10576 0 evdev 14076 0 snd_rawmidi 27180 2 snd_mpu401_uart,snd_seq_midi snd_seq_midi_event 10576 1 snd_seq_midi snd_via82xx_modem 17208 0 snd_ac97_codec 108936 2 snd_via82xx,snd_via82xx_modem ac97_bus 5188 1 snd_ac97_codec snd_pcm_oss 45784 0 snd_mixer_oss 21040 1 snd_pcm_oss snd_seq 59096 2 snd_seq_midi,snd_seq_midi_event snd_seq_device 11044 3 snd_seq_midi,snd_rawmidi,snd_seq snd_pcm 80484 4 snd_via82xx,snd_via82xx_modem,snd_ac97_codec,snd_pcm_oss via_ircc 35544 0 snd_timer 25828 2 snd_seq,snd_pcm vt8231 21420 0 snd_page_alloc 13244 3 snd_via82xx,snd_via82xx_modem,snd_pcm snd 66876 11 snd_via82xx,snd_mpu401_uart,snd_rawmidi,snd_via82xx_modem,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_seq,snd_seq_device,snd_pcm,snd_timer via_rhine 26152 0 i2c_viapro 12368 0 irda 121852 1 via_ircc soundcore 10324 1 snd crc_ccitt 5404 1 irda parport_pc 35176 0 parport 40916 1 parport_pc hfcpci 30528 0 firewire_ohci 28232 0 firewire_core 50252 1 firewire_ohci mISDN_core 91260 1 hfcpci crc_itu_t 5780 1 firewire_core ext3 138112 5 jbd 50856 1 ext3 mbcache 11432 1 ext3 sha256_generic 13404 0 aes_generic 32288 4 cbc 7160 2 dm_crypt 17392 2 dm_mirror 18736 0 dm_region_hash 15420 1 dm_mirror dm_log 13808 2 dm_mirror,dm_region_hash dm_snapshot 29348 0 dm_mod 65304 37 dm_crypt,dm_mirror,dm_log,dm_snapshot ide_cd_mod 32544 0 cdrom 41392 1 ide_cd_mod i2c_powermac 8320 0 ata_generic 8432 0 libata 177008 1 ata_generic ide_pci_generic 7428 0 via82cxxx 9812 4 usb_storage 58348 1 sd_mod 37912 2 scsi_mod 157268 3 libata,usb_storage,sd_mod crc_t10dif 5260 1 sd_mod raid1 26532 1 md_mod 100080 2 raid1 uhci_hcd 30272 0 usbhid 43392 0 hid 48168 1 usbhid ehci_hcd 44376 0 ** PCI devices: 0000:00:00.0 Host bridge [0600]: Marvell Technology Group Ltd. MV64360/64361/64362 System Controller [11ab:6460] (rev 03) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR+ INTx- Latency: 0, Cache Line Size: 128 bytes Interrupt: pin A routed to IRQ 0 0000:00:01.0 FireWire (IEEE 1394) [0c00]: VIA Technologies, Inc. VT6306 Fire II IEEE 1394 OHCI Link Layer Controller [1106:3044] (rev 46) (prog-if 10 [OHCI]) Subsystem: VIA Technologies, Inc. VT6306 Fire II IEEE 1394 OHCI Link Layer Controller [1106:3044] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (8000ns max) Interrupt: pin A routed to IRQ 9 Region 0: Memory at 80002000 (32-bit, non-prefetchable) [size=2K] Region 1: I/O ports at 1080 [size=128] Capabilities: <access denied> Kernel driver in use: firewire_ohci 0000:00:05.0 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 43) (prog-if 10 [OHCI]) Subsystem: NEC Corporation Hama USB 2.0 CardBus [1033:0035] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 8 (250ns min, 10500ns max) Interrupt: pin A routed to IRQ 9 Region 0: Memory at 80000000 (32-bit, non-prefetchable) [size=4K] Capabilities: <access denied> Kernel driver in use: ohci_hcd 0000:00:05.1 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 43) (prog-if 10 [OHCI]) Subsystem: NEC Corporation Hama USB 2.0 CardBus [1033:0035] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 8 (250ns min, 10500ns max) Interrupt: pin B routed to IRQ 9 Region 0: Memory at 80001000 (32-bit, non-prefetchable) [size=4K] Capabilities: <access denied> Kernel driver in use: ohci_hcd 0000:00:05.2 USB Controller [0c03]: NEC Corporation USB 2.0 [1033:00e0] (rev 04) (prog-if 20 [EHCI]) Subsystem: NetMos Technology Device [9710:1906] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 68 (4000ns min, 8500ns max), Cache Line Size: 32 bytes Interrupt: pin C routed to IRQ 9 Region 0: Memory at 80002800 (32-bit, non-prefetchable) [size=256] Capabilities: <access denied> Kernel driver in use: ehci_hcd 0000:00:06.0 Network controller [0280]: Cologne Chip Designs GmbH ISDN network controller [HFC-PCI] [1397:2bd0] (rev 02) Subsystem: Cologne Chip Designs GmbH ISDN Board [1397:2bd0] Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin A routed to IRQ 9 Region 0: I/O ports at 1030 [disabled] [size=8] Region 1: Memory at 80002900 (32-bit, non-prefetchable) [size=256] Capabilities: <access denied> Kernel driver in use: hfcpci 0000:00:0c.0 ISA bridge [0601]: VIA Technologies, Inc. VT8231 [PCI-to-ISA Bridge] [1106:8231] (rev 10) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel driver in use: parport_pc 0000:00:0c.1 IDE interface [0101]: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE [1106:0571] (rev 06) (prog-if 8a [Master SecP PriP]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin ? routed to IRQ 14 Region 0: [virtual] I/O ports at 1000 [size=8] Region 1: [virtual] I/O ports at 100c [size=4] Region 2: [virtual] I/O ports at 1010 [size=8] Region 3: [virtual] I/O ports at 101c [size=4] Region 4: I/O ports at 1020 [size=16] Capabilities: <access denied> Kernel driver in use: VIA_IDE 0000:00:0c.2 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 1e) (prog-if 00 [UHCI]) Subsystem: First International Computer, Inc. VA-502 Mainboard [0925:1234] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 22 Interrupt: pin D routed to IRQ 9 Region 4: I/O ports at 1040 [size=32] Capabilities: <access denied> Kernel driver in use: uhci_hcd 0000:00:0c.3 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 1e) (prog-if 00 [UHCI]) Subsystem: First International Computer, Inc. VA-502 Mainboard [0925:1234] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 22 Interrupt: pin D routed to IRQ 9 Region 4: I/O ports at 1060 [size=32] Capabilities: <access denied> Kernel driver in use: uhci_hcd 0000:00:0c.4 Bridge [0680]: VIA Technologies, Inc. VT8235 ACPI [1106:8235] (rev 10) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: <access denied> Kernel driver in use: vt596_smbus 0000:00:0c.5 Multimedia audio controller [0401]: VIA Technologies, Inc. VT82C686 AC97 Audio Controller [1106:3058] (rev 40) Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin C routed to IRQ 9 Region 0: I/O ports at 1100 [size=256] Region 1: I/O ports at 1038 [size=4] Region 2: I/O ports at 103c [size=4] Capabilities: <access denied> Kernel driver in use: VIA 82xx Audio 0000:00:0c.6 Communication controller [0780]: VIA Technologies, Inc. AC'97 Modem Controller [1106:3068] (rev 20) Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin C routed to IRQ 9 Region 0: I/O ports at 1200 [size=256] Capabilities: <access denied> 0000:00:0d.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6102 [Rhine-II] [1106:3065] (rev 51) Subsystem: Device [3065:1106] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (63750ns min, 63750ns max) Interrupt: pin A routed to IRQ 9 Region 0: I/O ports at 1300 [size=256] Region 1: Memory at 80002a00 (32-bit, non-prefetchable) [size=256] Capabilities: <access denied> Kernel driver in use: via-rhine 0001:01:00.0 Host bridge [0600]: Marvell Technology Group Ltd. MV64360/64361/64362 System Controller [11ab:6460] (rev 03) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 128 bytes Interrupt: pin A routed to IRQ 0 0001:01:08.0 VGA compatible controller [0300]: ATI Technologies Inc RV280 [Radeon 9200 SE] [1002:5964] (rev 01) (prog-if 00 [VGA controller]) Subsystem: ABIT Computer Corp. R9200SE-DT [147b:6191] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (2000ns min) Interrupt: pin A routed to IRQ 9 Region 0: Memory at c0000000 (32-bit, prefetchable) [size=128M] Region 1: I/O ports at 1000 [size=256] Region 2: Memory at c8000000 (32-bit, non-prefetchable) [size=64K] Expansion ROM at c8020000 [disabled] [size=128K] Capabilities: <access denied> Kernel driver in use: radeonfb 0001:01:08.1 Display controller [0380]: ATI Technologies Inc RV280 [Radeon 9200 SE] (Secondary) [1002:5d44] (rev 01) Subsystem: ABIT Computer Corp. R9200SE-DT (Secondary) [147b:6190] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Region 0: Memory at d0000000 (32-bit, prefetchable) [disabled] [size=128M] Region 1: Memory at c8010000 (32-bit, non-prefetchable) [disabled] [size=64K] Capabilities: <access denied> -- System Information: Debian Release: squeeze/sid APT prefers unstable APT policy: (500, 'unstable') Architecture: powerpc (ppc) Kernel: Linux 2.6.30-1-powerpc Locale: LANG=ja_JP.UTF-8, LC_CTYPE=ja_JP.UTF-8 (charmap=UTF-8) Shell: /bin/sh linked to /bin/dash Versions of packages linux-image-2.6.30-1-powerpc depends on: ii debconf [debconf-2.0] 1.5.27 Debian configuration management sy ii initramfs-tools [linux-initra 0.93.4 tools for generating an initramfs ii libc6 2.9-24 GNU C Library: Shared libraries ii module-init-tools 3.10-3 tools for managing Linux kernel mo linux-image-2.6.30-1-powerpc recommends no packages. Versions of packages linux-image-2.6.30-1-powerpc suggests: pn linux-doc-2.6.30 <none> (no description available) ii mkvmlinuz 35 create a kernel to boot a PowerPC -- debconf information: linux-image-2.6.30-1-powerpc/postinst/old-system-map-link-2.6.30-1-powerpc: true shared/kernel-image/really-run-bootloader: true linux-image-2.6.30-1-powerpc/preinst/elilo-initrd-2.6.30-1-powerpc: true linux-image-2.6.30-1-powerpc/preinst/abort-install-2.6.30-1-powerpc: linux-image-2.6.30-1-powerpc/prerm/would-invalidate-boot-loader-2.6.30-1-powerpc: true linux-image-2.6.30-1-powerpc/postinst/old-dir-initrd-link-2.6.30-1-powerpc: true linux-image-2.6.30-1-powerpc/postinst/old-initrd-link-2.6.30-1-powerpc: true * linux-image-2.6.30-1-powerpc/preinst/bootloader-initrd-2.6.30-1-powerpc: false linux-image-2.6.30-1-powerpc/postinst/depmod-error-2.6.30-1-powerpc: false linux-image-2.6.30-1-powerpc/prerm/removing-running-kernel-2.6.30-1-powerpc: true linux-image-2.6.30-1-powerpc/postinst/bootloader-error-2.6.30-1-powerpc: linux-image-2.6.30-1-powerpc/preinst/abort-overwrite-2.6.30-1-powerpc: linux-image-2.6.30-1-powerpc/preinst/failed-to-move-modules-2.6.30-1-powerpc: linux-image-2.6.30-1-powerpc/preinst/lilo-has-ramdisk: linux-image-2.6.30-1-powerpc/postinst/create-kimage-link-2.6.30-1-powerpc: true linux-image-2.6.30-1-powerpc/postinst/kimage-is-a-directory: linux-image-2.6.30-1-powerpc/postinst/depmod-error-initrd-2.6.30-1-powerpc: false linux-image-2.6.30-1-powerpc/preinst/overwriting-modules-2.6.30-1-powerpc: true linux-image-2.6.30-1-powerpc/preinst/initrd-2.6.30-1-powerpc: linux-image-2.6.30-1-powerpc/postinst/bootloader-test-error-2.6.30-1-powerpc: linux-image-2.6.30-1-powerpc/preinst/lilo-initrd-2.6.30-1-powerpc: true
Attachment:
cpu
Description: PNG image
Attachment:
memory
Description: PNG image
