Bug#543398: linux-image-2.6.30-1-686: e100 is missing a dependency on linux-firmware
Package: linux-image-2.6.30-1-686
Version: 2.6.30-5
Severity: important
In the 2.6.30 kernel, but not in 2.6.26, e100 depends on d101m_ucode.bin,
from firmware-linux.
The kernel package is not marked as depending on this. Consequently, if
you reboot into your newly installed 2.6.30 kernel, your networking, if
using an E10/100 card for instance, is irretrievably broken.
-- Package-specific info:
** Version:
Linux version 2.6.30-1-686 (Debian 2.6.30-5) (maks@debian.org) (gcc version 4.3.3 (Debian 4.3.3-15) ) #1 SMP Mon Aug 3 16:18:30 UTC 2009
** Command line:
root=/dev/hda1 ro
** Not tainted
** Kernel log:
[ 3.439776] hdb: unknown partition table
[ 3.463618] hdc: max request size: 128KiB
[ 3.486058] hdc: 150136560 sectors (76869 MB) w/1916KiB Cache, CHS=65535/16/63
[ 3.486190] hdc: cache flushes not supported
[ 3.486318] hdc: hdc1
[ 3.503498] ide-cd: hdd: ATAPI 52X CD-ROM drive, 128kB Cache
[ 3.503686] Uniform CD-ROM driver Revision: 3.20
[ 16.480023] scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
[ 16.480026] <Adaptec 2902/04/10/15/20C/30C SCSI adapter>
[ 16.480028] aic7850: Single Channel A, SCSI Id=7, 3/253 SCBs
[ 16.480030]
[ 16.481500] ohci_hcd 0000:02:01.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 16.481587] ohci_hcd 0000:02:01.0: OHCI Host Controller
[ 16.481709] ohci_hcd 0000:02:01.0: new USB bus registered, assigned bus number 1
[ 16.481800] ohci_hcd 0000:02:01.0: irq 19, io mem 0xfeaf5000
[ 16.536048] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 16.536106] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 16.536165] usb usb1: Product: OHCI Host Controller
[ 16.536213] usb usb1: Manufacturer: Linux 2.6.30-1-686 ohci_hcd
[ 16.536262] usb usb1: SerialNumber: 0000:02:01.0
[ 16.536425] usb usb1: configuration #1 chosen from 1 choice
[ 16.536518] hub 1-0:1.0: USB hub found
[ 16.536577] hub 1-0:1.0: 2 ports detected
[ 16.536800] sata_via 0000:02:0c.0: version 2.4
[ 16.536826] sata_via 0000:02:0c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 16.536944] sata_via 0000:02:0c.0: routed to hard irq line 10
[ 16.538599] scsi1 : sata_via
[ 16.538781] scsi2 : sata_via
[ 16.539155] scsi3 : sata_via
[ 16.539266] ata1: SATA max UDMA/133 port i16@0xdfa0 bmdma 0xdf40 irq 17
[ 16.539319] ata2: SATA max UDMA/133 port i16@0xdf90 bmdma 0xdf48 irq 17
[ 16.539369] ata3: PATA max UDMA/133 port i16@0xdf80 bmdma 0xdf50 irq 17
[ 16.539489] ohci_hcd 0000:02:01.1: PCI INT B -> GSI 18 (level, low) -> IRQ 18
[ 16.539575] ohci_hcd 0000:02:01.1: OHCI Host Controller
[ 16.539666] ohci_hcd 0000:02:01.1: new USB bus registered, assigned bus number 2
[ 16.539757] ohci_hcd 0000:02:01.1: irq 18, io mem 0xfeaf6000
[ 16.592045] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 16.592102] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 16.592160] usb usb2: Product: OHCI Host Controller
[ 16.592208] usb usb2: Manufacturer: Linux 2.6.30-1-686 ohci_hcd
[ 16.592258] usb usb2: SerialNumber: 0000:02:01.1
[ 16.592424] usb usb2: configuration #1 chosen from 1 choice
[ 16.592518] hub 2-0:1.0: USB hub found
[ 16.592575] hub 2-0:1.0: 2 ports detected
[ 16.870893] ata1: SATA link down (SStatus 0 SControl 310)
[ 17.198888] ata2: SATA link down (SStatus 0 SControl 310)
[ 17.870387] PM: Starting manual resume from disk
[ 17.983514] kjournald starting. Commit interval 5 seconds
[ 17.983578] EXT3-fs: mounted filesystem with ordered data mode.
[ 19.881515] udev: starting version 141
[ 20.118188] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 20.118258] ACPI: Power Button [PWRF]
[ 20.118398] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2
[ 20.118463] ACPI: Power Button [PBTN]
[ 20.124898] processor ACPI_CPU:00: registered as cooling_device0
[ 20.279539] input: PC Speaker as /devices/platform/pcspkr/input/input3
[ 20.303906] parport_pc 00:0a: reported by Plug and Play ACPI
[ 20.304052] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[ 20.357868] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 20.386242] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 20.388427] intel_rng: Firmware space is locked read-only. If you can't or
[ 20.388430] intel_rng: don't want to disable this in firmware setup, and if
[ 20.388432] intel_rng: you are certain that your system has a functional
[ 20.388434] intel_rng: RNG, try using the 'no_fwh_detect' option.
[ 20.394626] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 20.682646] input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input4
[ 22.887083] Adding 2650684k swap on /dev/hda5. Priority:-1 extents:1 across:2650684k
[ 23.344244] EXT3 FS on hda1, internal journal
[ 23.942484] loop: module loaded
[ 24.423183] kjournald starting. Commit interval 5 seconds
[ 24.423439] EXT3 FS on hdb, internal journal
[ 24.423524] EXT3-fs: mounted filesystem with ordered data mode.
[ 24.430434] kjournald starting. Commit interval 5 seconds
[ 24.430655] EXT3 FS on hdc1, internal journal
[ 24.430738] EXT3-fs: mounted filesystem with ordered data mode.
[ 26.033866] e100 0000:02:0d.0: firmware: requesting e100/d101m_ucode.bin
[ 26.135460] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 28.816221] e100: eth0 NIC Link is Up 100 Mbps Full Duplex
[ 28.816586] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 29.432576] RPC: Registered udp transport module.
[ 29.432631] RPC: Registered tcp transport module.
[ 29.489839] Slow work thread pool: Starting up
[ 29.491544] Slow work thread pool: Ready
[ 29.491660] FS-Cache: Loaded
[ 29.544713] FS-Cache: Netfs 'nfs' registered for caching
[ 29.566221] svc: failed to register lockdv1 RPC service (errno 97).
[ 30.597837] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 30.674361] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 30.684113] NFSD: starting 90-second grace period
[ 35.525659] lp0: using parport0 (interrupt-driven).
[ 35.566577] ppdev: user-space parallel port driver
[ 38.900008] eth0: no IPv6 routers present
[ 39.884587] [drm] Initialized drm 1.1.0 20060810
[ 39.892458] pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 39.892769] [drm] Initialized mga 3.2.1 20051102 for 0000:01:00.0 on minor 0
[ 39.896959] agpgart-intel 0000:00:00.0: AGP 2.0 bridge
[ 39.896980] agpgart-intel 0000:00:00.0: putting AGP V2 device into 1x mode
[ 39.897000] pci 0000:01:00.0: putting AGP V2 device into 1x mode
[ 39.916088] [drm] Initialized card for AGP DMA.
[ 39.966823] platform mga_warp.0: firmware: requesting matrox/g400_warp.fw
** Loaded modules:
Module Size Used by
mga 25892 2
drm 137920 3 mga
ppdev 6348 0
lp 8012 0
nfsd 204900 9
exportfs 3792 1 nfsd
battery 6012 0
nfs 221580 1
lockd 57972 2 nfsd,nfs
fscache 34440 1 nfs
nfs_acl 2640 2 nfsd,nfs
auth_rpcgss 31416 2 nfsd,nfs
sunrpc 163772 14 nfsd,nfs,lockd,nfs_acl,auth_rpcgss
speedstep_lib 4136 0
cpufreq_userspace 2768 0
cpufreq_stats 3520 0
cpufreq_powersave 1292 0
cpufreq_conservative 6256 0
dm_snapshot 21604 0
loop 13324 0
i2c_i801 8564 0
shpchp 26648 0
i2c_core 20844 2 drm,i2c_i801
serio_raw 4560 0
rng_core 3672 0
pci_hotplug 24400 1 shpchp
parport_pc 22420 1
evdev 8028 6
psmouse 37528 0
pcspkr 2104 0
parport 31144 3 ppdev,lp,parport_pc
processor 34504 0
button 5060 0
ext3 107172 3
jbd 41036 1 ext3
mbcache 6924 1 ext3
ide_cd_mod 24484 0
cdrom 30316 1 ide_cd_mod
ide_gd_mod 19852 6
ide_pci_generic 3632 0
ata_generic 4340 0
sata_via 8384 0
libata 150904 2 ata_generic,sata_via
ohci_hcd 19880 0
ehci_hcd 29680 0
piix 5680 4
aic7xxx 104820 0
usbcore 126004 3 ohci_hcd,ehci_hcd
scsi_transport_spi 18544 1 aic7xxx
scsi_mod 131800 3 libata,aic7xxx,scsi_transport_spi
e100 27464 0
mii 4664 1 e100
ide_core 88100 4 ide_cd_mod,ide_gd_mod,ide_pci_generic,piix
intel_agp 22900 1
agpgart 30836 2 drm,intel_agp
floppy 46220 0
thermal 12580 0
fan 4044 0
thermal_sys 13140 3 processor,thermal,fan
dm_mirror 12580 0
dm_region_hash 10668 1 dm_mirror
dm_log 8464 2 dm_mirror,dm_region_hash
dm_mod 49992 3 dm_snapshot,dm_mirror,dm_log
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82850 850 (Tehama) Chipset Host Bridge (MCH) [8086:2530] (rev 04)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:01.0 PCI bridge [0604]: Intel Corporation 82850 850 (Tehama) Chipset AGP Bridge [8086:2532] (rev 04) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
Memory behind bridge: fd500000-fe5fffff
Prefetchable memory behind bridge: f1200000-f52fffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev 04) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fe600000-feafffff
Prefetchable memory behind bridge: f5300000-f53fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:1f.0 ISA bridge [0601]: Intel Corporation 82801BA ISA Bridge (LPC) [8086:2440] (rev 04)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:1f.1 IDE interface [0101]: Intel Corporation 82801BA IDE U100 Controller [8086:244b] (rev 04) (prog-if 80 [Master])
Subsystem: Intel Corporation Device [8086:4d44]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
Region 4: I/O ports at ffa0 [size=16]
Kernel driver in use: PIIX_IDE
00:1f.3 SMBus [0c05]: Intel Corporation 82801BA/BAM SMBus Controller [8086:2443] (rev 04)
Subsystem: Intel Corporation Device [8086:4d44]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at efa0 [size=16]
Kernel driver in use: i801_smbus
01:00.0 VGA compatible controller [0300]: Matrox Graphics, Inc. MGA G400/G450 [102b:0525] (rev 04) (prog-if 00 [VGA controller])
Subsystem: Matrox Graphics, Inc. Millennium G400 16Mb SDRAM [102b:0338]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (4000ns min, 8000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f2000000 (32-bit, prefetchable) [size=32M]
Region 1: Memory at fe5fc000 (32-bit, non-prefetchable) [size=16K]
Region 2: Memory at fd800000 (32-bit, non-prefetchable) [size=8M]
Expansion ROM at fe5e0000 [disabled] [size=64K]
Capabilities: <access denied>
02:01.0 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 41) (prog-if 10 [OHCI])
Subsystem: Intel Corporation Device [8086:4d44]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (250ns min, 10500ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at feaf5000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
02:01.1 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 41) (prog-if 10 [OHCI])
Subsystem: Intel Corporation Device [8086:4d44]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (250ns min, 10500ns max), Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 18
Region 0: Memory at feaf6000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
02:0b.0 SCSI storage controller [0100]: Adaptec AIC-7850 [9004:5078] (rev 03)
Subsystem: Adaptec AHA-2904/Integrated AIC-7850 [9004:7850]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (1000ns min, 1000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 23
Region 0: I/O ports at d800 [disabled] [size=256]
Region 1: Memory at feaf4000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: aic7xxx
02:0c.0 RAID bus controller [0104]: VIA Technologies, Inc. VT6421 IDE RAID Controller [1106:3249] (rev 50)
Subsystem: VIA Technologies, Inc. VT6421 IDE RAID Controller [1106:3249]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at dfa0 [size=16]
Region 1: I/O ports at df90 [size=16]
Region 2: I/O ports at df80 [size=16]
Region 3: I/O ports at df60 [size=16]
Region 4: I/O ports at df40 [size=32]
Region 5: I/O ports at d400 [size=256]
Expansion ROM at fe600000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: sata_via
02:0d.0 Ethernet controller [0200]: Intel Corporation 82557/8/9/0/1 Ethernet Pro 100 [8086:1229] (rev 08)
Subsystem: Intel Corporation EtherExpress PRO/100+ Management Adapter [8086:000c]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (2000ns min, 14000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at feaf3000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at df00 [size=64]
Region 2: Memory at fe900000 (32-bit, non-prefetchable) [size=1M]
Expansion ROM at f5300000 [disabled] [size=1M]
Capabilities: <access denied>
Kernel driver in use: e100
** Sound cards:
-- System Information:
Debian Release: squeeze/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: i386 (i686)
Kernel: Linux 2.6.30-1-686 (SMP w/1 CPU core)
Locale: LANG=en_GB.UTF-8, LC_CTYPE=en_GB.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.30-1-686 depends on:
ii debconf [debconf-2.0] 1.5.27 Debian configuration management sy
ii initramfs-tools [linux-initra 0.93.4 tools for generating an initramfs
ii module-init-tools 3.9-2 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.30-1-686 recommends:
ii libc6-i686 2.9-23 GNU C Library: Shared libraries [i
Versions of packages linux-image-2.6.30-1-686 suggests:
ii grub 0.97-56 GRand Unified Bootloader (dummy pa
ii grub-legacy [grub] 0.97-56 GRand Unified Bootloader (Legacy v
pn linux-doc-2.6.30 <none> (no description available)
-- debconf information:
linux-image-2.6.30-1-686/preinst/lilo-has-ramdisk:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.30-1-686/postinst/old-initrd-link-2.6.30-1-686: true
linux-image-2.6.30-1-686/postinst/create-kimage-link-2.6.30-1-686: true
linux-image-2.6.30-1-686/postinst/depmod-error-2.6.30-1-686: false
linux-image-2.6.30-1-686/postinst/old-system-map-link-2.6.30-1-686: true
linux-image-2.6.30-1-686/prerm/would-invalidate-boot-loader-2.6.30-1-686: true
linux-image-2.6.30-1-686/preinst/overwriting-modules-2.6.30-1-686: true
linux-image-2.6.30-1-686/preinst/lilo-initrd-2.6.30-1-686: true
linux-image-2.6.30-1-686/postinst/old-dir-initrd-link-2.6.30-1-686: true
linux-image-2.6.30-1-686/preinst/failed-to-move-modules-2.6.30-1-686:
linux-image-2.6.30-1-686/postinst/bootloader-test-error-2.6.30-1-686:
linux-image-2.6.30-1-686/preinst/abort-install-2.6.30-1-686:
linux-image-2.6.30-1-686/postinst/bootloader-error-2.6.30-1-686:
linux-image-2.6.30-1-686/preinst/initrd-2.6.30-1-686:
linux-image-2.6.30-1-686/prerm/removing-running-kernel-2.6.30-1-686: true
linux-image-2.6.30-1-686/postinst/kimage-is-a-directory:
linux-image-2.6.30-1-686/preinst/abort-overwrite-2.6.30-1-686:
linux-image-2.6.30-1-686/preinst/elilo-initrd-2.6.30-1-686: true
linux-image-2.6.30-1-686/preinst/bootloader-initrd-2.6.30-1-686: true
linux-image-2.6.30-1-686/postinst/depmod-error-initrd-2.6.30-1-686: false
Reply to: