--- Begin Message ---
- To: Debian Bug Tracking System <submit@bugs.debian.org>
- Subject: linux-image-2.6.22-2-686: unknown NMI on resume on thinkpad T60p
- From: Jerry Quinn <jlquinn@optonline.net>
- Date: Wed, 17 Oct 2007 03:14:07 -0400
- Message-id: <20071017071407.15943.8379.reportbug@localhost>
Package: linux-image-2.6.22-2-686
Version: 2.6.22-4
Severity: normal
When I resume after sleep, I get the following messages on consoles and in the kernel log:
Message from syslogd@naga at Wed Oct 17 02:55:24 2007 ...
naga kernel: Uhhuh. NMI received for unknown reason a0 on CPU 0.
Message from syslogd@naga at Wed Oct 17 02:55:24 2007 ...
naga kernel: You have some hardware problem, likely on the PCI bus.
Message from syslogd@naga at Wed Oct 17 02:55:24 2007 ...
naga kernel: Dazed and confused, but trying to continue
The system appears to keep working normally despite the messages. This is a thinkpad T60p with
2G memory.
I can reproduce this problem on an untainted kernel. The taint is from the madwifi driver.
This bug has been present in kernels since 2.6.18.
I'm pretty sure this is not due to the particular laptop being broken. I transferred my drive
into an identical machine and the same problem happens there.
-- Package-specific info:
** Version:
Linux version 2.6.22-2-686 (Debian 2.6.22-4) (waldi@debian.org) (gcc version 4.1.3 20070812 (prerelease) (Debian 4.1.2-15)) #1 SMP Fri Aug 31 00:24:01 UTC 2007
** Tainted: PFSRMB
** Kernel log:
PM: Writing back config space on device 0000:00:01.0 at offset 1 (was 100107, writing 40100507)
PCI: Setting latency timer of device 0000:00:01.0 to 64
PM: Writing back config space on device 0000:00:1b.0 at offset 1 (was 100106, writing 100102)
ACPI: PCI Interrupt 0000:00:1b.0[B] -> GSI 17 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1b.0 to 64
PM: Writing back config space on device 0000:00:1c.0 at offset 1 (was 180107, writing 100507)
PCI: Setting latency timer of device 0000:00:1c.0 to 64
PM: Writing back config space on device 0000:00:1c.1 at offset 1 (was 100107, writing 100507)
PCI: Setting latency timer of device 0000:00:1c.1 to 64
PM: Writing back config space on device 0000:00:1c.2 at offset 1 (was 100107, writing 100507)
PCI: Setting latency timer of device 0000:00:1c.2 to 64
PM: Writing back config space on device 0000:00:1c.3 at offset f (was 40400, writing 4040b)
PM: Writing back config space on device 0000:00:1c.3 at offset 9 (was 10001, writing e421e421)
PM: Writing back config space on device 0000:00:1c.3 at offset 8 (was 0, writing ebf0ea00)
PM: Writing back config space on device 0000:00:1c.3 at offset 7 (was 20000000, writing 20009080)
PM: Writing back config space on device 0000:00:1c.3 at offset 3 (was 810000, writing 810010)
PM: Writing back config space on device 0000:00:1c.3 at offset 1 (was 100000, writing 100507)
PCI: Setting latency timer of device 0000:00:1c.3 to 64
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.0 to 64
usb usb1: root hub lost power or was reset
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1d.1 to 64
usb usb2: root hub lost power or was reset
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:1d.2 to 64
usb usb3: root hub lost power or was reset
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.3 to 64
usb usb4: root hub lost power or was reset
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 19 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.7 to 64
PM: Writing back config space on device 0000:00:1e.0 at offset 1 (was 100005, writing 100007)
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt 0000:00:1f.1[C] -> GSI 16 (level, low) -> IRQ 16
PM: Writing back config space on device 0000:00:1f.2 at offset 1 (was 2b00007, writing 2b00407)
PCI: Setting latency timer of device 0000:00:1f.2 to 64
PM: Writing back config space on device 0000:01:00.0 at offset 1 (was 100103, writing 100107)
PM: Writing back config space on device 0000:02:00.0 at offset 1 (was 100107, writing 100103)
PM: Writing back config space on device 0000:15:00.0 at offset f (was 34001ff, writing 5c0010b)
PM: Writing back config space on device 0000:15:00.0 at offset e (was 0, writing a4fc)
PM: Writing back config space on device 0000:15:00.0 at offset d (was 0, writing a400)
PM: Writing back config space on device 0000:15:00.0 at offset c (was 0, writing a0fc)
PM: Writing back config space on device 0000:15:00.0 at offset b (was 0, writing a000)
PM: Writing back config space on device 0000:15:00.0 at offset a (was 0, writing 8bfff000)
PM: Writing back config space on device 0000:15:00.0 at offset 9 (was 0, writing 88000000)
PM: Writing back config space on device 0000:15:00.0 at offset 8 (was 0, writing e3fff000)
PM: Writing back config space on device 0000:15:00.0 at offset 7 (was 0, writing e0000000)
PM: Writing back config space on device 0000:15:00.0 at offset 6 (was 0, writing b0171615)
PM: Writing back config space on device 0000:15:00.0 at offset 4 (was 0, writing e4300000)
PM: Writing back config space on device 0000:15:00.0 at offset 3 (was 20000, writing 2a808)
PM: Writing back config space on device 0000:15:00.0 at offset 1 (was 2100000, writing 2100007)
pnp: Device 00:0a activated.
ata2: SATA link down (SStatus 0 SControl 0)
ata3: SATA link down (SStatus 0 SControl 0)
ata4: SATA link down (SStatus 0 SControl 0)
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/100
sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
usb_endpoint usbdev5.1_ep00: PM: resume from 0, parent usb5 still 2
usb_endpoint usbdev5.1_ep81: PM: resume from 0, parent 5-0:1.0 still 2
usb_device usbdev5.1: PM: resume from 0, parent usb5 still 2
sd 0:0:0:0: [sda] Starting disk
hda: selected mode 0x42
nsc_ircc_init_dongle_interface(), No dongle connected
nsc_ircc_change_dongle_speed(), No dongle connected is not for IrDA mode
Restarting tasks ... done.
input: Power Button (FF) as /class/input/input11
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /class/input/input12
ACPI: Lid Switch [LID]
input: Sleep Button (CM) as /class/input/input13
ACPI: Sleep Button (CM) [SLPB]
Uhhuh. NMI received for unknown reason b0 on CPU 0.
You have some hardware problem, likely on the PCI bus.
Dazed and confused, but trying to continue
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 0.9.18.0 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
wlan: 0.8.4.2 (0.9.3.2)
ath_pci: 0.9.4.5 (0.9.3.2)
ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 17 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:03:00.0 to 64
ath_rate_sample: 1.2 (0.9.3.2)
wifi0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: H/W encryption support: WEP AES AES_CCM TKIP
wifi0: mac 10.3 phy 6.1 radio 10.2
wifi0: Use hw queue 1 for WME_AC_BE traffic
wifi0: Use hw queue 0 for WME_AC_BK traffic
wifi0: Use hw queue 2 for WME_AC_VI traffic
wifi0: Use hw queue 3 for WME_AC_VO traffic
wifi0: Use hw queue 8 for CAB traffic
wifi0: Use hw queue 9 for beacons
wifi0: Atheros 5212: mem=0xedf00000, irq=21
ath0: no IPv6 routers present
ipsec0: no IPv6 routers present
** Loaded modules:
Module Size Used by
xfrm4_mode_tunnel 2880 2
esp4 7584 2
wlan_scan_sta 12480 1
ath_rate_sample 11808 1
ath_pci 88384 0
wlan 183620 4 wlan_scan_sta,ath_rate_sample,ath_pci
ath_hal 191504 3 ath_rate_sample,ath_pci
button 7920 0
e1000 113440 0
nvram 8488 1
uinput 8864 1
ppdev 8676 0
parport_pc 33796 0
lp 10980 0
parport 33960 3 ppdev,parport_pc,lp
dummy 2852 0
ac 5188 0
battery 9988 0
autofs4 20452 1
ipv6 236964 27
acpi_cpufreq 9096 1
cpufreq_userspace 4128 0
cpufreq_stats 5120 0
cpufreq_powersave 1792 0
cpufreq_ondemand 8300 1
freq_table 4512 3 acpi_cpufreq,cpufreq_stats,cpufreq_ondemand
cpufreq_conservative 6888 0
tun 10560 0
deflate 3712 0
zlib_deflate 17720 1 deflate
twofish 8448 0
twofish_common 36192 1 twofish
camellia 31168 0
serpent 18848 0
blowfish 8512 0
des 16544 2
cbc 4416 2
ecb 3520 0
blkcipher 6244 2 cbc,ecb
aes 27680 0
xcbc 5672 0
sha256 11008 0
sha1 2560 0
crypto_null 2528 0
af_key 33712 0
dm_snapshot 16516 0
dm_mirror 20928 0
dm_mod 52160 2 dm_snapshot,dm_mirror
loop 16932 0
joydev 9568 0
tsdev 7968 0
irtty_sir 8064 0
sir_dev 15396 1 irtty_sir
pcmcia 37100 0
firmware_class 9504 1 pcmcia
snd_hda_intel 239160 1
snd_pcm_oss 39200 0
snd_mixer_oss 15424 1 snd_pcm_oss
snd_pcm 72324 2 snd_hda_intel,snd_pcm_oss
snd_timer 21028 1 snd_pcm
nsc_ircc 21328 0
snd 48324 7 snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
psmouse 36016 0
yenta_socket 24844 1
rsrc_nonstatic 11968 1 yenta_socket
soundcore 7520 1 snd
irda 172092 3 irtty_sir,sir_dev,nsc_ircc
pcmcia_core 37108 3 pcmcia,yenta_socket,rsrc_nonstatic
snd_page_alloc 9512 2 snd_hda_intel,snd_pcm
serio_raw 6692 0
i2c_i801 8656 0
intel_agp 23188 0
agpgart 31912 1 intel_agp
crc_ccitt 2144 1 irda
i2c_core 23552 1 i2c_i801
iTCO_wdt 9924 0
evdev 9312 6
rtc 12856 0
pcspkr 3104 0
ext3 121224 1
jbd 55336 1 ext3
mbcache 8260 1 ext3
ide_cd 36416 0
cdrom 32832 1 ide_cd
ata_generic 7556 0
sd_mod 27136 3
piix 8868 0 [permanent]
generic 4836 0 [permanent]
ide_core 113764 3 ide_cd,piix,generic
ahci 21380 2
libata 115664 2 ata_generic,ahci
scsi_mod 136620 2 sd_mod,libata
ehci_hcd 30796 0
uhci_hcd 22960 0
usbcore 125096 3 ehci_hcd,uhci_hcd
thermal 13416 0
processor 31016 2 acpi_cpufreq,thermal
fan 4836 0
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Mobile 945GM/PM/GMS/940GML and 945GT Express Memory Controller Hub [8086:27a0] (rev 03)
Subsystem: Lenovo Unknown device [17aa:2015]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00:01.0 PCI bridge [0604]: Intel Corporation Mobile 945GM/PM/GMS/940GML and 945GT Express PCI Express Root Port [8086:27a1] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR+ <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: ee100000-ee1fffff
Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [88] Subsystem: Lenovo Unknown device [17aa:2014]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee0100c Data: 00d1
Capabilities: [a0] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 2
Link: Latency L0s <1us, L1 <4us
Link: ASPM L0s L1 Enabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 1, PowerLimit 75.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [100] Virtual Channel
Capabilities: [140] Unknown (5)
00:1b.0 Audio device [0403]: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller [8086:27d8] (rev 02)
Subsystem: Lenovo Thinkpad R60e model 0657 [17aa:2010]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 21
Region 0: Memory at ee400000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express Unknown type IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed unknown, Width x0, ASPM unknown, Port 0
Link: Latency L0s <64ns, L1 <1us
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed unknown, Width x0
Capabilities: [100] Virtual Channel
Capabilities: [130] Unknown (5)
00:1c.0 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 [8086:27d0] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: ee000000-ee0fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 1
Link: Latency L0s <256ns, L1 <4us
Link: ASPM L1 Enabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 2, PowerLimit 6.500000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq+
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
Address: fee0100c Data: 00d9
Capabilities: [90] Subsystem: Lenovo Unknown device [17aa:2011]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel
Capabilities: [180] Unknown (5)
00:1c.1 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 [8086:27d2] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00004000-00005fff
Memory behind bridge: ec000000-edffffff
Prefetchable memory behind bridge: 00000000e4000000-00000000e40fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 2
Link: Latency L0s <256ns, L1 <4us
Link: ASPM L1 Enabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 3, PowerLimit 6.500000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee0100c Data: 00e1
Capabilities: [90] Subsystem: Lenovo Unknown device [17aa:2011]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel
Capabilities: [180] Unknown (5)
00:1c.2 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3 [8086:27d4] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=0b, sec-latency=0
I/O behind bridge: 00006000-00007fff
Memory behind bridge: e8000000-e9ffffff
Prefetchable memory behind bridge: 00000000e4100000-00000000e41fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 3
Link: Latency L0s <1us, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x0
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 4, PowerLimit 6.500000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq+
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee0100c Data: 00e9
Capabilities: [90] Subsystem: Lenovo Unknown device [17aa:2011]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel
Capabilities: [180] Unknown (5)
00:1c.3 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 4 [8086:27d6] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0c, subordinate=13, sec-latency=0
I/O behind bridge: 00008000-00009fff
Memory behind bridge: ea000000-ebffffff
Prefetchable memory behind bridge: 00000000e4200000-00000000e42fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 4
Link: Latency L0s <1us, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x0
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 5, PowerLimit 6.500000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee0100c Data: 0032
Capabilities: [90] Subsystem: Lenovo Unknown device [17aa:2011]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel
Capabilities: [180] Unknown (5)
00:1d.0 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI #1 [8086:27c8] (rev 02) (prog-if 00 [UHCI])
Subsystem: Lenovo Thinkpad R60e model 0657 [17aa:200a]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at 1800 [size=32]
00:1d.1 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI #2 [8086:27c9] (rev 02) (prog-if 00 [UHCI])
Subsystem: Lenovo Thinkpad R60e model 0657 [17aa:200a]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at 1820 [size=32]
00:1d.2 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI #3 [8086:27ca] (rev 02) (prog-if 00 [UHCI])
Subsystem: Lenovo Thinkpad R60e model 0657 [17aa:200a]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 22
Region 4: I/O ports at 1840 [size=32]
00:1d.3 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI #4 [8086:27cb] (rev 02) (prog-if 00 [UHCI])
Subsystem: Lenovo Thinkpad R60e model 0657 [17aa:200a]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 23
Region 4: I/O ports at 1860 [size=32]
00:1d.7 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller [8086:27cc] (rev 02) (prog-if 20 [EHCI])
Subsystem: Lenovo Thinkpad R60e model 0657 [17aa:200b]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 23
Region 0: Memory at ee404000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=15, subordinate=18, sec-latency=32
I/O behind bridge: 0000a000-0000dfff
Memory behind bridge: e4300000-e7ffffff
Prefetchable memory behind bridge: 00000000e0000000-00000000e3ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Subsystem: Lenovo Unknown device [17aa:2013]
00:1f.0 ISA bridge [0601]: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge [8086:27b9] (rev 02)
Subsystem: Lenovo Thinkpad R60e model 0657 [17aa:2009]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00:1f.1 IDE interface [0101]: Intel Corporation 82801G (ICH7 Family) IDE Controller [8086:27df] (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Lenovo Thinkpad R60e model 0657 [17aa:200c]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 1880 [size=16]
00:1f.2 SATA controller [0106]: Intel Corporation 82801GBM/GHM (ICH7 Family) Serial ATA Storage Controller AHCI [8086:27c5] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Lenovo Thinkpad R60e model 0657 [17aa:200d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 218
Region 0: I/O ports at 18c8 [size=8]
Region 1: I/O ports at 18ac [size=4]
Region 2: I/O ports at 18c0 [size=8]
Region 3: I/O ports at 18a8 [size=4]
Region 4: I/O ports at 18b0 [size=16]
Region 5: Memory at ee404400 (32-bit, non-prefetchable) [size=1K]
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee0100c Data: 0052
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1f.3 SMBus [0c05]: Intel Corporation 82801G (ICH7 Family) SMBus Controller [8086:27da] (rev 02)
Subsystem: Lenovo Thinkpad R60e model 0657 [17aa:200f]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 18e0 [size=32]
01:00.0 VGA compatible controller [0300]: ATI Technologies Inc M56GL [ATI Mobility FireGL V5200] [1002:71c4] (prog-if 00 [VGA])
Subsystem: Lenovo Unknown device [17aa:2007]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 1: I/O ports at 2000 [size=256]
Region 2: Memory at ee100000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at ee120000 [disabled] [size=128K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express Legacy Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <4us, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 0
Link: Latency L0s <64ns, L1 <1us
Link: ASPM L0s L1 Enabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
02:00.0 Ethernet controller [0200]: Intel Corporation 82573L Gigabit Ethernet Controller [8086:109a]
Subsystem: Lenovo Unknown device [17aa:2001]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 16
Region 0: Memory at ee000000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 3000 [size=32]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [e0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <64us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 0
Link: Latency L0s <128ns, L1 <64us
Link: ASPM L1 Enabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Device Serial Number a6-f9-cd-ff-ff-6b-1a-00
03:00.0 Ethernet controller [0200]: Atheros Communications, Inc. AR5212 802.11abg NIC [168c:1014] (rev 01)
Subsystem: IBM Unknown device [1014:058a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at edf00000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [60] Express Legacy Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <64us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 0
Link: Latency L0s <512ns, L1 <64us
Link: ASPM L0s L1 Enabled RCB 128 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Capabilities: [90] MSI-X: Enable- Mask- TabSize=1
Vector table: BAR=0 offset=00000000
PBA: BAR=0 offset=00000000
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
15:00.0 CardBus bridge [0607]: Texas Instruments PCI1510 PC card Cardbus Controller [104c:ac56]
Subsystem: Lenovo Unknown device [17aa:2012]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at e4300000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=15, secondary=16, subordinate=17, sec-latency=176
Memory window 0: e0000000-e3fff000 (prefetchable)
Memory window 1: 88000000-8bfff000
I/O window 0: 0000a000-0000a0ff
I/O window 1: 0000a400-0000a4ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
-- System Information:
Debian Release: lenny/sid
APT prefers testing
APT policy: (990, 'testing'), (500, 'unstable'), (500, 'stable')
Architecture: i386 (i686)
Kernel: Linux 2.6.22-2-686 (SMP w/2 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.22-2-686 depends on:
ii initramfs-tools [linux-initr 0.90a tools for generating an initramfs
ii module-init-tools 3.3-pre11-4 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.22-2-686 recommends:
ii libc6-i686 2.6.1-1+b1 GNU C Library: Shared libraries [i
-- debconf information:
linux-image-2.6.22-2-686/preinst/lilo-has-ramdisk:
linux-image-2.6.22-2-686/prerm/would-invalidate-boot-loader-2.6.22-2-686: true
linux-image-2.6.22-2-686/preinst/elilo-initrd-2.6.22-2-686: true
linux-image-2.6.22-2-686/preinst/abort-overwrite-2.6.22-2-686:
linux-image-2.6.22-2-686/preinst/lilo-initrd-2.6.22-2-686: true
linux-image-2.6.22-2-686/postinst/depmod-error-initrd-2.6.22-2-686: false
linux-image-2.6.22-2-686/preinst/overwriting-modules-2.6.22-2-686: true
linux-image-2.6.22-2-686/preinst/failed-to-move-modules-2.6.22-2-686:
linux-image-2.6.22-2-686/preinst/bootloader-initrd-2.6.22-2-686: true
linux-image-2.6.22-2-686/postinst/create-kimage-link-2.6.22-2-686: true
linux-image-2.6.22-2-686/postinst/bootloader-error-2.6.22-2-686:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.22-2-686/postinst/kimage-is-a-directory:
linux-image-2.6.22-2-686/postinst/old-dir-initrd-link-2.6.22-2-686: true
linux-image-2.6.22-2-686/prerm/removing-running-kernel-2.6.22-2-686: true
linux-image-2.6.22-2-686/preinst/initrd-2.6.22-2-686:
linux-image-2.6.22-2-686/postinst/depmod-error-2.6.22-2-686: false
linux-image-2.6.22-2-686/preinst/already-running-this-2.6.22-2-686:
linux-image-2.6.22-2-686/postinst/old-initrd-link-2.6.22-2-686: true
linux-image-2.6.22-2-686/postinst/bootloader-test-error-2.6.22-2-686:
linux-image-2.6.22-2-686/preinst/abort-install-2.6.22-2-686:
linux-image-2.6.22-2-686/postinst/old-system-map-link-2.6.22-2-686: true
--- End Message ---