Bug#538183: marked as done (Initramfs scrips not waiting for resources to be detected)
Your message dated Fri, 24 Jul 2009 00:32:24 +0200
with message-id <20090723223224.GB16147@baikonur.stro.at>
and subject line Re: Bug#538183: Initramfs scrips not waiting for resources to be detected
has caused the Debian Bug report #538183,
regarding Initramfs scrips not waiting for resources to be detected
to be marked as done.
This means that you claim that the problem has been dealt with.
If this is not the case it is now your responsibility to reopen the
Bug report if necessary, and/or fix the problem forthwith.
(NB: If you are a system administrator and have no idea what this
message is talking about, this may indicate a serious mail system
misconfiguration somewhere. Please contact owner@bugs.debian.org
immediately.)
--
538183: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=538183
Debian Bug Tracking System
Contact owner@bugs.debian.org with problems
--- Begin Message ---
Package: initramfs-tools
Version: 0.92o
Kernel version: 2.6.26-2-sparc64
HW: Sun Ultra 10
Relevant config: two scsi drives in RAID 1 with LVM
Relevant dmesg output:
Loading, please wait...
Begin: Loading essential drivers ... [ 20.898599] SCSI subsystem initialized
[ 20.977137] sym0: <875> rev 0x14 at pci 0000:02:01.0 irq 15
[ 21.134875] sym0: No NVRAM, ID 7, Fast-20, SE, parity checking
[ 21.215741] sym0: SCSI BUS has been reset.
[ 21.268732] scsi0 : sym-2.2.3
[ 21.310085] sym1: <875> rev 0x14 at pci 0000:02:01.1 irq 16
[ 21.467646] sym1: No NVRAM, ID 7, Fast-20, SE, parity checking
[ 21.548472] sym1: SCSI BUS has been reset.
[ 21.601118] scsi1 : sym-2.2.3
done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... Begi1
Success: loaded module raid1.
done.
Begin: Assembling all MD arrays ... mdadm: No devices[ 23.358934] device-mapp3
listed [ 23.422496] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialim
in conf file were found.
Failure: failed to assemble all arrays.
done.
Begin: Waiting for udev to process events ... done.
Volume group "master" not found
done.
Begin: Waiting for root file system ... [ 25.711800] scsi 1:0:4:0: Direct-Acc3
[ 25.818227] target1:0:4: tagged command queuing enabled, command queue dept.
[ 25.917176] target1:0:4: Beginning Domain Validation
[ 25.982347] target1:0:4: asynchronous
[ 26.035053] target1:0:4: wide asynchronous
[ 26.089994] target1:0:4: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 16)
[ 26.180011] target1:0:4: Domain Validation skipping write tests
[ 26.255967] target1:0:4: Ending Domain Validation
[ 26.596428] scsi 1:0:6:0: Direct-Access MAXTOR ATLAS10K4_73WLS DFV0 P3
[ 26.703112] target1:0:6: tagged command queuing enabled, command queue dept.
[ 26.802606] target1:0:6: Beginning Domain Validation
[ 26.867628] target1:0:6: asynchronous
[ 26.920958] target1:0:6: wide asynchronous
[ 26.976164] target1:0:6: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 16)
[ 27.066817] target1:0:6: Domain Validation skipping write tests
[ 27.143229] target1:0:6: Ending Domain Validation
[ 29.599158] Driver 'sd' needs updating - please use bus_type methods
[ 29.700670] sd 1:0:4:0: [sda] 143666192 512-byte hardware sectors (73557 MB)
[ 29.791818] sd 1:0:4:0: [sda] Write Protect is off
[ 29.854854] sd 1:0:4:0: [sda] Write cache: enabled, read cache: enabled, supA
[ 29.969089] sd 1:0:4:0: [sda] 143666192 512-byte hardware sectors (73557 MB)
[ 30.059983] sd 1:0:4:0: [sda] Write Protect is off
[ 30.124598] sd 1:0:4:0: [sda] Write cache: enabled, read cache: enabled, supA
[ 30.236425] sda: sda1 sda2 sda3 sda4
<similar sdb output>
As seen from the dmesg output the init scripts try to setup the software
raid before the scsi-drives are available, which in turn causes both
MD and LVM to fail.
--- End Message ---
--- Begin Message ---
On Thu, Jul 23, 2009 at 10:01:59PM +0200, Kjetil Oftedal wrote:
> Package: initramfs-tools
> Version: 0.92o
>
> Kernel version: 2.6.26-2-sparc64
> HW: Sun Ultra 10
> Relevant config: two scsi drives in RAID 1 with LVM
>
> Relevant dmesg output:
> Loading, please wait...
> Begin: Loading essential drivers ... [ 20.898599] SCSI subsystem
> initialized
> [ 20.977137] sym0: <875> rev 0x14 at pci 0000:02:01.0 irq 15
> [ 21.134875] sym0: No NVRAM, ID 7, Fast-20, SE, parity checking
> [ 21.215741] sym0: SCSI BUS has been reset.
> [ 21.268732] scsi0 : sym-2.2.3
> [ 21.310085] sym1: <875> rev 0x14 at pci 0000:02:01.1 irq 16
> [ 21.467646] sym1: No NVRAM, ID 7, Fast-20, SE, parity checking
> [ 21.548472] sym1: SCSI BUS has been reset.
> [ 21.601118] scsi1 : sym-2.2.3
> done.
> Begin: Running /scripts/init-premount ... done.
> Begin: Mounting root file system ... Begin: Running /scripts/local-top ...
> Begi1
> Success: loaded module raid1.
> done.
> Begin: Assembling all MD arrays ... mdadm: No devices[ 23.358934]
> device-mapp3
> listed [ 23.422496] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18)
> initialim
> in conf file were found.
> Failure: failed to assemble all arrays.
> done.
> Begin: Waiting for udev to process events ... done.
> Volume group "master" not found
> done.
> Begin: Waiting for root file system ... [ 25.711800] scsi 1:0:4:0:
> Direct-Acc3
> [ 25.818227] target1:0:4: tagged command queuing enabled, command queue
> dept.
> [ 25.917176] target1:0:4: Beginning Domain Validation
> [ 25.982347] target1:0:4: asynchronous
> [ 26.035053] target1:0:4: wide asynchronous
> [ 26.089994] target1:0:4: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset
> 16)
> [ 26.180011] target1:0:4: Domain Validation skipping write tests
> [ 26.255967] target1:0:4: Ending Domain Validation
> [ 26.596428] scsi 1:0:6:0: Direct-Access MAXTOR ATLAS10K4_73WLS
> DFV0 P3
> [ 26.703112] target1:0:6: tagged command queuing enabled, command queue
> dept.
> [ 26.802606] target1:0:6: Beginning Domain Validation
> [ 26.867628] target1:0:6: asynchronous
> [ 26.920958] target1:0:6: wide asynchronous
> [ 26.976164] target1:0:6: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset
> 16)
> [ 27.066817] target1:0:6: Domain Validation skipping write tests
> [ 27.143229] target1:0:6: Ending Domain Validation
> [ 29.599158] Driver 'sd' needs updating - please use bus_type methods
> [ 29.700670] sd 1:0:4:0: [sda] 143666192 512-byte hardware sectors (73557
> MB)
> [ 29.791818] sd 1:0:4:0: [sda] Write Protect is off
> [ 29.854854] sd 1:0:4:0: [sda] Write cache: enabled, read cache: enabled,
> supA
> [ 29.969089] sd 1:0:4:0: [sda] 143666192 512-byte hardware sectors (73557
> MB)
> [ 30.059983] sd 1:0:4:0: [sda] Write Protect is off
> [ 30.124598] sd 1:0:4:0: [sda] Write cache: enabled, read cache: enabled,
> supA
> [ 30.236425] sda: sda1 sda2 sda3 sda4
> <similar sdb output>
>
> As seen from the dmesg output the init scripts try to setup the software
> raid before the scsi-drives are available, which in turn causes both
> MD and LVM to fail.
>
read release notes, use rootdelay bootparam.
--- End Message ---
Reply to: