[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Bug#534593: marked as done (linux-image-2.6.29-2-amd64: NVIDIA PXE bootloader fails with PXE-E61 error after install)

Your message dated Tue, 30 Jun 2009 19:03:48 -0600
with message-id <20090701010348.GA6002@lackof.org>
and subject line done
has caused the Debian Bug report #534593,
regarding linux-image-2.6.29-2-amd64: NVIDIA PXE bootloader fails with PXE-E61 error after install
to be marked as done.

This means that you claim that the problem has been dealt with.
If this is not the case it is now your responsibility to reopen the
Bug report if necessary, and/or fix the problem forthwith.

(NB: If you are a system administrator and have no idea what this
message is talking about, this may indicate a serious mail system
misconfiguration somewhere. Please contact owner@bugs.debian.org
immediately.)


-- 
534593: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=534593
Debian Bug Tracking System
Contact owner@bugs.debian.org with problems
--- Begin Message --- 
Package: linux-image-2.6.29-2-amd64
Version: 2.6.29-5
Severity: important

*** Please type your report below this line ***
I am having some troubles with PXE booting our servers that are running fully up to date Debian Squeeze/Sid. The servers have AMD Opteron 1218 on a supermicro H8SMU motherboard using the nVidia MCP55 Pro chipset. The problem I am running into is that after Squeeze/Sid has been installed, on reboots of the machine, the nVidia PXE bootloader fails to start, giving the error message: "PXE-E61: Media test failure check cable".
Going into the BIOS screen on boot and clearing the NVRAM or changing a setting and saving will correct the problem for the next boot. However, on a subsequent reboot the same error occurs. Also, rebooting after the PXE failure at the GRUB screen will also cause PXE booting to happen normally until Debian Squeeze/Sid fully boots up.
The netbooting error does not occur with Debian 4.0, Debian 5.0, nor many other linux distributions. 


-- Package-specific info:
** Version:
Linux version 2.6.29-2-amd64 (Debian 2.6.29-5) (waldi@debian.org) (gcc version 4.3.3 (Debian 4.3.3-10) ) #1 SMP Sun May 17 17:15:47 UTC 2009 

** Command line:
ro root=/dev/sda1 root=/dev/sda1  ro quiet

** Not tainted

** Kernel log:
[ 0.884806] sata_nv 0000:00:05.0: PCI INT A -> Link[LSA0] -> GSI 20 (level, low) -> IRQ 20 
[    0.884808] sata_nv 0000:00:05.0: Using SWNCQ mode
[    0.884867] sata_nv 0000:00:05.0: setting latency timer to 64
[    0.885006] scsi0 : sata_nv
[    0.896293] Uniform Multi-Platform E-IDE driver
[    0.896423] scsi1 : sata_nv
[ 0.896587] ata1: SATA max UDMA/133 cmd 0xd480 ctl 0xd400 bmdma 0xcc00 irq 20 [ 0.896589] ata2: SATA max UDMA/133 cmd 0xd080 ctl 0xd000 bmdma 0xcc08 irq 20 
[    0.908853] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.776032] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.811487] ata1.00: ATA-8: ST3320613AS, CC2F, max UDMA/133
[ 1.811490] ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32) 
[    1.867488] ata1.00: configured for UDMA/133
[    1.867530] isa bounce pool size: 16 pages
[ 1.867599] scsi 0:0:0:0: Direct-Access ATA ST3320613AS CC2F PQ: 0 ANSI: 5 
[    2.598197] ata2: SATA link down (SStatus 0 SControl 300)
[    2.598226] amd74xx 0000:00:04.0: UDMA133 controller
[ 2.598229] amd74xx 0000:00:04.0: IDE controller (0x10de:0x036e rev 0xa1) 
[    2.598244] amd74xx 0000:00:04.0: IDE port disabled
[ 2.598255] amd74xx 0000:00:04.0: not 100% native mode: will probe irqs later 
[    2.598259]     ide0: BM-DMA at 0xffa0-0xffa7
[    2.598264] Probing IDE interface ide0...
[    3.612084] hdb: MATSHITADVD-ROM SR-8178, ATAPI CD/DVD-ROM drive
[    3.668034] hdb: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 3.668288] hdb: host side 80-wire cable detection failed, limiting max speed to UDMA33 
[    3.668290] hdb: UDMA/33 mode selected
[    3.668565] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[    3.671511] ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 23
[ 3.671515] ohci_hcd 0000:00:02.0: PCI INT A -> Link[LUB0] -> GSI 23 (level, low) -> IRQ 23 
[    3.671544] ohci_hcd 0000:00:02.0: setting latency timer to 64
[    3.671547] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 3.671621] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2 
[    3.671634] ohci_hcd 0000:00:02.0: irq 23, io mem 0xfeafb000
[ 3.726014] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.726016] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 
[    3.726018] usb usb2: Product: OHCI Host Controller
[    3.726020] usb usb2: Manufacturer: Linux 2.6.29-2-amd64 ohci_hcd
[    3.726021] usb usb2: SerialNumber: 0000:00:02.0
[    3.726065] usb usb2: configuration #1 chosen from 1 choice
[    3.726090] hub 2-0:1.0: USB hub found
[    3.726097] hub 2-0:1.0: 10 ports detected
[    3.726471] ACPI: PCI Interrupt Link [LSA1] enabled at IRQ 22
[ 3.726473] sata_nv 0000:00:05.1: PCI INT B -> Link[LSA1] -> GSI 22 (level, low) -> IRQ 22 
[    3.726475] sata_nv 0000:00:05.1: Using SWNCQ mode
[    3.726525] sata_nv 0000:00:05.1: setting latency timer to 64
[    3.726644] scsi2 : sata_nv
[    3.726702] scsi3 : sata_nv
[ 3.726824] ata3: SATA max UDMA/133 cmd 0xc880 ctl 0xc800 bmdma 0xc080 irq 22 [ 3.726827] ata4: SATA max UDMA/133 cmd 0xc480 ctl 0xc400 bmdma 0xc088 irq 22 [ 4.100014] usb 2-2: new low speed USB device using ohci_hcd and address 2 
[    4.316026] usb 2-2: New USB device found, idVendor=045e, idProduct=00cb
[ 4.316029] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 
[    4.316032] usb 2-2: Product: Microsoft Basic Optical Mouse v2.0
[    4.316033] usb 2-2: Manufacturer: Microsoft
[    4.316096] usb 2-2: configuration #1 chosen from 1 choice
[    4.326254] usbcore: registered new interface driver hiddev
[ 4.332253] input: Microsoft Microsoft Basic Optical Mouse v2.0 as /devices/pci0000:00/0000:00:02.0/usb2/2-2/2-2:1.0/input/input2 [ 4.341056] generic-usb 0003:045E:00CB.0001: input,hidraw0: USB HID v1.11 Mouse [Microsoft Microsoft Basic Optical Mouse v2.0 ] on usb-0000:00:02.0-2/input0 
[    4.341076] usbcore: registered new interface driver usbhid
[    4.341079] usbhid: v2.6:USB HID core driver
[    4.458200] ata3: SATA link down (SStatus 0 SControl 300)
[    5.190194] ata4: SATA link down (SStatus 0 SControl 300)
[    5.196970] ide-cd driver 5.00
[    5.197549] ide-cd: hdb: ATAPI 24X DVD-ROM drive, 256kB Cache
[    5.197553] Uniform CD-ROM driver Revision: 3.20
[    5.296185] Driver 'sd' needs updating - please use bus_type methods
[ 5.296288] sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors: (320 GB/298 GiB) 
[    5.296302] sd 0:0:0:0: [sda] Write Protect is off
[    5.296304] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.296323] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 5.296376] sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors: (320 GB/298 GiB) 
[    5.296386] sd 0:0:0:0: [sda] Write Protect is off
[    5.296388] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.296405] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA 
[    5.296409]  sda: sda1 sda2 < sda5 >
[    5.338866] sd 0:0:0:0: [sda] Attached SCSI disk
[    5.397564] PM: Starting manual resume from disk
[    5.463119] kjournald starting.  Commit interval 5 seconds
[    5.463128] EXT3-fs: mounted filesystem with ordered data mode.
[   14.156687] udev: starting version 141
[ 28.433840] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3 
[   28.441134] ACPI: Power Button (FF) [PWRF]
[ 28.441243] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4 
[   28.449123] ACPI: Power Button (CM) [PWRB]
[   28.766572] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x2d00
[   28.766589] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x2e00
[ 28.944498] k8temp 0000:00:18.3: Temperature readouts might be wrong - check erratum #141 
[   29.274190] input: PC Speaker as /devices/platform/pcspkr/input/input5
[   29.330627] Error: Driver 'pcspkr' is already registered, aborting...
[ 30.424987] Adding 20244412k swap on /dev/sda5. Priority:-1 extents:1 across:20244412k 
[   30.561471] EXT3 FS on sda1, internal journal
[   31.457547] loop: module loaded
[   32.132177]   alloc irq_desc for 30 on cpu 0 node 0
[   32.132180]   alloc kstat_irqs on cpu 0 node 0
[   32.132189] forcedeth 0000:00:08.0: irq 30 for MSI/MSI-X
[   35.799212] RPC: Registered udp transport module.
[   35.799215] RPC: Registered tcp transport module.
[   37.166622] NET: Registered protocol family 10
[   37.167196] lo: Disabled Privacy Extensions
[   47.612011] eth0: no IPv6 routers present

** Loaded modules:
Module                  Size  Used by
autofs4                26728  1
ipv6                  283776  12
nfs                   250560  2
lockd                  67924  1 nfs
nfs_acl                 3232  1 nfs
auth_rpcgss            40768  1 nfs
sunrpc                194936  13 nfs,lockd,nfs_acl,auth_rpcgss
loop                   15292  0
snd_pcsp               10652  0
serio_raw               5780  0
snd_pcm                78776  1 snd_pcsp
snd_timer              22240  1 snd_pcm
snd                    63192  3 snd_pcsp,snd_pcm,snd_timer
soundcore               7984  1 snd
snd_page_alloc          9776  1 snd_pcm
k8temp                  5008  0
psmouse                41532  0
i2c_nforce2             7400  0
i2c_core               25168  1 i2c_nforce2
evdev                  10496  3
button                  7280  0
ext3                  122528  1
jbd                    50232  1 ext3
mbcache                 9140  1 ext3
sd_mod                 32632  3
crc_t10dif              2064  1 sd_mod
ide_cd_mod             30192  0
cdrom                  33592  1 ide_cd_mod
ide_pci_generic         4628  0
usbhid                 34176  0
hid                    40928  1 usbhid
ata_generic             5876  0
ohci_hcd               23036  0
amd74xx                 6840  0
ide_core              108788  3 ide_cd_mod,ide_pci_generic,amd74xx
sata_nv                24840  2
forcedeth              52336  0
libata                172716  2 ata_generic,sata_nv
scsi_mod              158880  2 sd_mod,libata
ehci_hcd               33916  0
thermal                18864  0
processor              45400  1 thermal
fan                     5304  0
thermal_sys            13104  3 thermal,processor,fan

** PCI devices:
00:00.0 RAM memory [0500]: nVidia Corporation MCP55 Memory Controller [10de:0369] (rev a2) 
  Subsystem: Super Micro Computer Inc Device [15d9:2011]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 
  Latency: 0
  Capabilities: <access denied>
00:01.0 ISA bridge [0601]: nVidia Corporation MCP55 LPC Bridge [10de:0364] (rev a3) 
  Subsystem: Super Micro Computer Inc Device [15d9:2011]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 
  Latency: 0

00:01.1 SMBus [0c05]: nVidia Corporation MCP55 SMBus [10de:0368] (rev a3)
  Subsystem: Super Micro Computer Inc Device [15d9:2011]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 
  Interrupt: pin A routed to IRQ 11
  Region 0: I/O ports at dc00 [size=64]
  Region 4: I/O ports at 2d00 [size=64]
  Region 5: I/O ports at 2e00 [size=64]
  Capabilities: <access denied>
  Kernel driver in use: nForce2_smbus
00:02.0 USB Controller [0c03]: nVidia Corporation MCP55 USB Controller [10de:036c] (rev a1) (prog-if 10 [OHCI]) 
  Subsystem: Super Micro Computer Inc Device [15d9:2011]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 
  Latency: 0 (750ns min, 250ns max)
  Interrupt: pin A routed to IRQ 23
  Region 0: Memory at feafb000 (32-bit, non-prefetchable) [size=4K]
  Capabilities: <access denied>
  Kernel driver in use: ohci_hcd
00:02.1 USB Controller [0c03]: nVidia Corporation MCP55 USB Controller [10de:036d] (rev a2) (prog-if 20 [EHCI]) 
  Subsystem: Super Micro Computer Inc Device [15d9:2011]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 
  Latency: 0 (750ns min, 250ns max)
  Interrupt: pin B routed to IRQ 23
  Region 0: Memory at feafac00 (32-bit, non-prefetchable) [size=256]
  Capabilities: <access denied>
  Kernel driver in use: ehci_hcd
00:04.0 IDE interface [0101]: nVidia Corporation MCP55 IDE [10de:036e] (rev a1) (prog-if 8a [Master SecP PriP]) 
  Subsystem: Super Micro Computer Inc Device [15d9:2011]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 
  Latency: 0 (750ns min, 250ns max)
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8] Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1] Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8] Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1] 
  Region 4: I/O ports at ffa0 [size=16]
  Capabilities: <access denied>
  Kernel driver in use: AMD_IDE
00:05.0 IDE interface [0101]: nVidia Corporation MCP55 SATA Controller [10de:037f] (rev a3) (prog-if 85 [Master SecO PriO]) 
  Subsystem: Super Micro Computer Inc Device [15d9:2011]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 
  Latency: 0 (750ns min, 250ns max)
  Interrupt: pin A routed to IRQ 20
  Region 0: I/O ports at d480 [size=8]
  Region 1: I/O ports at d400 [size=4]
  Region 2: I/O ports at d080 [size=8]
  Region 3: I/O ports at d000 [size=4]
  Region 4: I/O ports at cc00 [size=16]
  Region 5: Memory at feaf9000 (32-bit, non-prefetchable) [size=4K]
  Capabilities: <access denied>
  Kernel driver in use: sata_nv
00:05.1 IDE interface [0101]: nVidia Corporation MCP55 SATA Controller [10de:037f] (rev a3) (prog-if 85 [Master SecO PriO]) 
  Subsystem: Super Micro Computer Inc Device [15d9:2011]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 
  Latency: 0 (750ns min, 250ns max)
  Interrupt: pin B routed to IRQ 22
  Region 0: I/O ports at c880 [size=8]
  Region 1: I/O ports at c800 [size=4]
  Region 2: I/O ports at c480 [size=8]
  Region 3: I/O ports at c400 [size=4]
  Region 4: I/O ports at c080 [size=16]
  Region 5: Memory at feaf8000 (32-bit, non-prefetchable) [size=4K]
  Capabilities: <access denied>
  Kernel driver in use: sata_nv
00:06.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI bridge [10de:0370] (rev a2) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 
  Latency: 0
  Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
  I/O behind bridge: 0000e000-0000efff
  Memory behind bridge: feb00000-febfffff
  Prefetchable memory behind bridge: f0000000-f7ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR- 
  BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
      PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn-
  Capabilities: <access denied>
00:08.0 Bridge [0680]: nVidia Corporation MCP55 Ethernet [10de:0373] (rev a3) 
  Subsystem: Super Micro Computer Inc Device [15d9:2011]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 
  Latency: 0 (250ns min, 5000ns max)
  Interrupt: pin A routed to IRQ 30
  Region 0: Memory at feaf7000 (32-bit, non-prefetchable) [size=4K]
  Region 1: I/O ports at c000 [size=8]
  Region 2: Memory at feafa800 (32-bit, non-prefetchable) [size=256]
  Region 3: Memory at feafa400 (32-bit, non-prefetchable) [size=16]
  Capabilities: <access denied>
  Kernel driver in use: forcedeth
00:09.0 Bridge [0680]: nVidia Corporation MCP55 Ethernet [10de:0373] (rev a3) 
  Subsystem: Super Micro Computer Inc Device [15d9:2011]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 
  Latency: 0 (250ns min, 5000ns max)
  Interrupt: pin A routed to IRQ 21
  Region 0: Memory at feaf6000 (32-bit, non-prefetchable) [size=4K]
  Region 1: I/O ports at bc00 [size=8]
  Region 2: Memory at feafa000 (32-bit, non-prefetchable) [size=256]
  Region 3: Memory at feaf5c00 (32-bit, non-prefetchable) [size=16]
  Capabilities: <access denied>
  Kernel driver in use: forcedeth
00:0a.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express bridge [10de:0376] (rev a3) (prog-if 00 [Normal decode]) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 
  Latency: 0, Cache Line Size: 64 bytes
  Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- 
  BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
      PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
  Capabilities: <access denied>
  Kernel driver in use: pcieport-driver
00:0b.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express bridge [10de:0374] (rev a3) (prog-if 00 [Normal decode]) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 
  Latency: 0, Cache Line Size: 64 bytes
  Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- 
  BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
      PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
  Capabilities: <access denied>
  Kernel driver in use: pcieport-driver
00:0c.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express bridge [10de:0374] (rev a3) (prog-if 00 [Normal decode]) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 
  Latency: 0, Cache Line Size: 64 bytes
  Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- 
  BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
      PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
  Capabilities: <access denied>
  Kernel driver in use: pcieport-driver
00:0d.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express bridge [10de:0378] (rev a3) (prog-if 00 [Normal decode]) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 
  Latency: 0, Cache Line Size: 64 bytes
  Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- 
  BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
      PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
  Capabilities: <access denied>
  Kernel driver in use: pcieport-driver
00:0e.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express bridge [10de:0375] (rev a3) (prog-if 00 [Normal decode]) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 
  Latency: 0, Cache Line Size: 64 bytes
  Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- 
  BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
      PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
  Capabilities: <access denied>
  Kernel driver in use: pcieport-driver
00:0f.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express bridge [10de:0377] (rev a3) (prog-if 00 [Normal decode]) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 
  Latency: 0, Cache Line Size: 64 bytes
  Bus: primary=00, secondary=07, subordinate=07, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- 
  BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
      PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
  Capabilities: <access denied>
  Kernel driver in use: pcieport-driver
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 
  Capabilities: <access denied>
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map [1022:1101] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller [1022:1102] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control [1022:1103] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 
  Capabilities: <access denied>
  Kernel driver in use: k8temp
01:06.0 VGA compatible controller [0300]: ATI Technologies Inc ES1000 [1002:515e] (rev 02) (prog-if 00 [VGA controller]) 
  Subsystem: Super Micro Computer Inc Device [15d9:2011]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 
  Latency: 64 (2000ns min), Cache Line Size: 64 bytes
  Interrupt: pin A routed to IRQ 10
  Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
  Region 1: I/O ports at e000 [size=256]
  Region 2: Memory at febf0000 (32-bit, non-prefetchable) [size=64K]
  Expansion ROM at feb00000 [disabled] [size=128K]
  Capabilities: <access denied>



-- System Information:
Debian Release: squeeze/sid
APT prefers unstable
APT policy: (500, 'unstable')
Architecture: amd64 (x86_64)

Kernel: Linux 2.6.29-2-amd64 (SMP w/2 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash

Versions of packages linux-image-2.6.29-2-amd64 depends on:
ii debconf [debconf-2.0] 1.5.26 Debian configuration management sy ii initramfs-tools [linux-initra 0.93.2 tools for generating an initramfs ii module-init-tools 3.7-pre9-1 tools for managing Linux kernel mo 

linux-image-2.6.29-2-amd64 recommends no packages.

Versions of packages linux-image-2.6.29-2-amd64 suggests:
ii grub 0.97-53 GRand Unified Bootloader (Legacy v 
pn  linux-doc-2.6.29              <none>     (no description available)

-- debconf information:
linux-image-2.6.29-2-amd64/preinst/abort-install-2.6.29-2-amd64:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.29-2-amd64/postinst/old-initrd-link-2.6.29-2-amd64: true
linux-image-2.6.29-2-amd64/preinst/failed-to-move-modules-2.6.29-2-amd64:
linux-image-2.6.29-2-amd64/postinst/old-system-map-link-2.6.29-2-amd64: true 
linux-image-2.6.29-2-amd64/preinst/elilo-initrd-2.6.29-2-amd64: true
linux-image-2.6.29-2-amd64/prerm/would-invalidate-boot-loader-2.6.29-2-amd64: true linux-image-2.6.29-2-amd64/postinst/create-kimage-link-2.6.29-2-amd64: true
linux-image-2.6.29-2-amd64/prerm/removing-running-kernel-2.6.29-2-amd64: true
linux-image-2.6.29-2-amd64/postinst/old-dir-initrd-link-2.6.29-2-amd64: true 
linux-image-2.6.29-2-amd64/preinst/lilo-has-ramdisk:
linux-image-2.6.29-2-amd64/postinst/kimage-is-a-directory:
linux-image-2.6.29-2-amd64/preinst/initrd-2.6.29-2-amd64:
linux-image-2.6.29-2-amd64/postinst/depmod-error-2.6.29-2-amd64: false
linux-image-2.6.29-2-amd64/preinst/abort-overwrite-2.6.29-2-amd64:
linux-image-2.6.29-2-amd64/postinst/bootloader-test-error-2.6.29-2-amd64:
linux-image-2.6.29-2-amd64/preinst/lilo-initrd-2.6.29-2-amd64: true
linux-image-2.6.29-2-amd64/preinst/bootloader-initrd-2.6.29-2-amd64: true
linux-image-2.6.29-2-amd64/preinst/overwriting-modules-2.6.29-2-amd64: true
linux-image-2.6.29-2-amd64/postinst/depmod-error-initrd-2.6.29-2-amd64: false 
linux-image-2.6.29-2-amd64/postinst/bootloader-error-2.6.29-2-amd64:

--- End Message ---
--- Begin Message --- 
Version: 2.6.30-1

Geoff, that's good news.

My guess was that this fixed it:

commit 5a9a8e32ebe269c71d8d3e78f9435fe7729f38e9
Author: Ed Swierk <eswierk@aristanetworks.com>
Date:   Tue Jun 2 00:19:52 2009 -0700

    forcedeth: add phy_power_down parameter, leave phy powered up by
    default (v2)
    
    Add a phy_power_down parameter to forcedeth: set to 1 to power
    down the phy and disable the link when an interface goes down; set
    to 0 to always leave the phy powered up.
    
    The phy power state persists across reboots; Windows, some BIOSes,
    and older versions of Linux don't bother to power up the phy again,
    forcing users to remove all power to get the interface working (see
    http://bugzilla.kernel.org/show_bug.cgi?id=13072).  Leaving the
    phy powered on is the safest default behavior.  Users accustomed to
    seeing the link state reflect the interface state and/or wanting to
    minimize power consumption can set phy_power_down=1 if
    compatibility with other OSes is not an issue.
    
    Signed-off-by: Ed Swierk <eswierk@aristanetworks.com>
    Signed-off-by: David S. Miller <davem@davemloft.net>


-- 
dann frazier

--- End Message ---
Reply to: