Bug#533616: linux-image-2.6.29-2-amd64: occasional ext3 filesystem corruption
Package: linux-image-2.6.29-2-amd64
Version: 2.6.29-5
Severity: grave
Justification: causes non-serious data loss
Yesterday, I found my root filesystem mounted read-only. Dmesg gave the
following messages (retyped by hand, which is why the timestamps are
missing):
EXT3-fs error (device sda3): htree_dirblock_to_tree: bad entry in directory
#91119000: directory entry accross blocks - offset=0, inode=2364050278,
rec_len=36552, name-len=216
Aborting journal on device sda3.
Remounting filesystem read-only
__journal_remove_journal_head: freeing b_comitted_data
Note the ridiculously large inode number mentioned in the first line.
After reboot, I needed to run fsck from the root prompt. An orphaned inode
list was fixed, a zero dtime was fixed, block bitmap differences were
fixed, free block counts were fixed, free inode counts were fixed. I seem
to recall inode bitmap differences were also fixed.
-- Package-specific info:
** Version:
Linux version 2.6.29-2-amd64 (Debian 2.6.29-5) (waldi@debian.org) (gcc version 4.3.3 (Debian 4.3.3-10) ) #1 SMP Sun May 17 17:15:47 UTC 2009
** Command line:
root=/dev/sda3 ro
** Not tainted
** Kernel log:
[10757.264576] firewire_ohci 0000:03:03.0: restoring config space at offset 0x3 (was 0x0, writing 0xf810)
[10757.264576] firewire_ohci 0000:03:03.0: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900216)
[10757.264576] Enabling non-boot CPUs ...
[10757.264576] SMP alternatives: switching to SMP code
[10757.387717] Booting processor 1 APIC 0x1 ip 0x6000
[10757.264016] Initializing CPU#1
[10757.264016] Calibrating delay using timer specific routine.. 4322.66 BogoMIPS (lpj=8645327)
[10757.264016] CPU: L1 I cache: 32K, L1 D cache: 32K
[10757.264016] CPU: L2 cache: 4096K
[10757.264016] CPU 1/0x1 -> Node 0
[10757.264016] CPU: Physical Processor ID: 0
[10757.264016] CPU: Processor Core ID: 1
[10757.264016] CPU1: Thermal monitoring enabled (TM2)
[10757.476572] CPU1: Intel(R) Core(TM)2 CPU T7400 @ 2.16GHz stepping 06
[10757.476614] CPU0 attaching NULL sched-domain.
[10757.477015] Switched to high resolution mode on CPU 1
[10757.488758] CPU0 attaching sched-domain:
[10757.488761] domain 0: span 0-1 level MC
[10757.488762] groups: 0 1
[10757.488766] CPU1 attaching sched-domain:
[10757.488767] domain 0: span 0-1 level MC
[10757.488769] groups: 1 0
[10757.492025] CPU1 is up
[10757.492027] ACPI: Waking up from system sleep state S3
[10757.696555] ACPI: EC: non-query interrupt received, switching to interrupt mode
[10757.859613] pci 0000:00:02.0: PME# disabled
[10757.859618] pci 0000:00:02.1: PME# disabled
[10757.859621] pci 0000:00:07.0: PME# disabled
[10757.859679] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[10757.859685] HDA Intel 0000:00:1b.0: setting latency timer to 64
[10757.859716] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[10757.859725] pcieport-driver 0000:00:1c.1: setting latency timer to 64
[10757.859760] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[10757.859765] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[10757.859790] usb usb2: root hub lost power or was reset
[10757.859850] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[10757.859855] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[10757.859879] usb usb3: root hub lost power or was reset
[10757.859922] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[10757.859928] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[10757.859951] usb usb4: root hub lost power or was reset
[10757.860004] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
[10757.860038] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[10757.860070] usb usb5: root hub lost power or was reset
[10757.860140] ehci_hcd 0000:00:1d.7: PME# disabled
[10757.860144] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[10757.860150] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[10757.860156] ehci_hcd 0000:00:1d.7: PME# disabled
[10757.860248] pci 0000:00:1e.0: power state changed by ACPI to D0
[10757.860255] pci 0000:00:1e.0: setting latency timer to 64
[10757.860297] PIIX_IDE 0000:00:1f.1: power state changed by ACPI to D0
[10757.860333] PIIX_IDE 0000:00:1f.1: power state changed by ACPI to D0
[10757.860337] PIIX_IDE 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[10757.860361] PIIX_IDE 0000:00:1f.1: restoring config space at offset 0x1 (was 0x2880005, writing 0x2800005)
[10757.860370] PIIX_IDE 0000:00:1f.1: setting latency timer to 64
[10757.860415] ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[10757.860419] ata_piix 0000:00:1f.2: setting latency timer to 64
[10757.860526] sky2 0000:01:00.0: restoring config space at offset 0x1 (was 0x40100407, writing 0x100407)
[10757.860588] sky2 0000:01:00.0: PME# disabled
[10757.860635] ath9k 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[10757.932148] firewire_core: skipped bus generations, destroying all nodes
[10758.044803] hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
[10758.045035] hda: UDMA/66 mode selected
[10758.045265] sd 0:0:1:0: [sda] Starting disk
[10758.432133] firewire_core: rediscovered device fw0
[10758.872430] ata1.01: ACPI cmd ef/03:0c:00:00:00:b0 filtered out
[10758.872432] ata1.01: ACPI cmd ef/03:45:00:00:00:b0 filtered out
[10758.956775] ata1.01: configured for UDMA/100
[10758.973795] sd 0:0:1:0: [sda] 234441648 512-byte hardware sectors: (120 GB/111 GiB)
[10758.973828] sd 0:0:1:0: [sda] Write Protect is off
[10758.973833] sd 0:0:1:0: [sda] Mode Sense: 00 3a 00 00
[10758.973878] sd 0:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[10759.828116] usb 2-2: reset full speed USB device using uhci_hcd and address 2
[10759.996170] appletouch: Geyser mode initialized.
[10760.108115] usb 4-2: reset full speed USB device using uhci_hcd and address 2
[10760.376148] usb 5-1: reset full speed USB device using uhci_hcd and address 2
[10760.550035] applesmc: device has already been initialized (0xe0, 0x00).
[10760.550098] pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[10760.550102] pci 0000:00:02.0: setting latency timer to 64
[10760.556013] Restarting tasks ... done.
[10760.727386] sky2 eth2: enabling interface
[10760.727722] ADDRCONF(NETDEV_UP): eth2: link is not ready
[10760.756406] ADDRCONF(NETDEV_UP): ath0: link is not ready
[10762.913579] ath0: direct probe to AP 00:15:f2:7a:ce:fb try 1
[10763.113067] ath0: direct probe to AP 00:15:f2:7a:ce:fb try 2
[10763.313096] ath0: direct probe to AP 00:15:f2:7a:ce:fb try 3
[10763.512065] ath0: direct probe to AP 00:15:f2:7a:ce:fb timed out
[10770.081373] ath0: authenticate with AP 00:13:10:06:b2:7e
[10770.087765] ath0: authenticated
[10770.087772] ath0: associate with AP 00:13:10:06:b2:7e
[10770.090102] ath0: RX AssocResp from 00:13:10:06:b2:7e (capab=0x411 status=0 aid=4)
[10770.090108] ath0: associated
[10770.091326] ADDRCONF(NETDEV_CHANGE): ath0: link becomes ready
[10780.504057] ath0: no IPv6 routers present
[10783.221464] ath0 direct probe responded
[10783.221471] ath0: authenticate with AP 00:13:10:06:b2:7e
[10783.227676] ath0: authenticated
[10783.227682] ath0: associate with AP 00:13:10:06:b2:7e
[10783.230076] ath0: RX ReassocResp from 00:13:10:06:b2:7e (capab=0x411 status=0 aid=4)
[10783.230083] ath0: associated
** Loaded modules:
Module Size Used by
i915 148616 2
drm 168208 3 i915
i2c_algo_bit 5956 1 i915
binfmt_misc 9308 1
ppdev 7528 0
parport_pc 26744 0
lp 10324 0
parport 37904 3 ppdev,parport_pc,lp
sco 10820 2
bridge 48048 0
stp 2836 1 bridge
bnep 13600 2
rfcomm 35104 0
l2cap 19968 6 bnep,rfcomm
bluetooth 53860 6 sco,bnep,rfcomm,l2cap
ipv6 283776 30
acpi_cpufreq 8376 0
cpufreq_conservative 7224 0
cpufreq_powersave 1760 0
cpufreq_stats 4836 0
cpufreq_userspace 3700 0
nf_conntrack_ipv4 14664 2
nf_defrag_ipv4 2256 1 nf_conntrack_ipv4
xt_state 2368 2
nf_conntrack 70048 2 nf_conntrack_ipv4,xt_state
xt_tcpudp 3296 4
iptable_filter 3744 1
ip_tables 17024 1 iptable_filter
x_tables 21800 3 xt_state,xt_tcpudp,ip_tables
firewire_sbp2 15056 0
loop 15292 0
arc4 2016 2
ecb 3040 2
snd_hda_codec_idt 61280 1
ath9k 230560 0
snd_hda_intel 26488 3
snd_hda_codec 69664 2 snd_hda_codec_idt,snd_hda_intel
mac80211 151592 1 ath9k
snd_hwdep 7864 1 snd_hda_codec
snd_pcm 78776 2 snd_hda_intel,snd_hda_codec
snd_seq 50800 0
cfg80211 38976 1 mac80211
snd_timer 22240 2 snd_pcm,snd_seq
snd_seq_device 7428 1 snd_seq
uvcvideo 55996 0
joydev 10944 0
rfkill 11876 2 ath9k
i2c_i801 9840 0
videodev 39568 1 uvcvideo
snd 63192 14 snd_hda_codec_idt,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_seq,snd_timer,snd_seq_device
soundcore 7984 1 snd
applesmc 28788 0
i2c_core 25168 4 i915,drm,i2c_algo_bit,i2c_i801
rng_core 4744 0
v4l1_compat 12612 2 uvcvideo,videodev
v4l2_compat_ioctl32 9168 1 videodev
snd_page_alloc 9776 2 snd_hda_intel,snd_pcm
appletouch 10564 0
led_class 4760 2 ath9k,applesmc
evdev 10496 17
battery 7600 0
pcspkr 2768 0
video 19972 0
output 3328 1 video
input_polldev 4400 1 applesmc
ac 3760 0
button 7280 0
ext3 122528 1
jbd 50232 1 ext3
mbcache 9140 1 ext3
hid_apple 7248 0
usbhid 34176 0
hid 40928 2 hid_apple,usbhid
sd_mod 32632 3
crc_t10dif 2064 1 sd_mod
ide_cd_mod 30192 0
cdrom 33592 1 ide_cd_mod
ata_generic 5876 0
ide_pci_generic 4628 0
uhci_hcd 22384 0
ata_piix 24196 2
libata 172716 2 ata_generic,ata_piix
scsi_mod 158880 3 firewire_sbp2,sd_mod,libata
piix 7144 0
ide_core 108788 3 ide_cd_mod,ide_pci_generic,piix
firewire_ohci 21988 0
firewire_core 39748 2 firewire_sbp2,firewire_ohci
crc_itu_t 2288 1 firewire_core
ehci_hcd 33916 0
sky2 46052 0
intel_agp 28240 1
thermal 18864 0
processor 45400 4 acpi_cpufreq,thermal
fan 5304 0
thermal_sys 13104 4 video,thermal,processor,fan
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub [8086:27a0] (rev 03)
Subsystem: Intel Corporation Device [8086:7270]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller [8086:27a2] (rev 03) (prog-if 00 [VGA controller])
Subsystem: Intel Corporation Device [8086:7270]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at 90380000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at 20e0 [size=8]
Region 2: Memory at 80000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at 90400000 (32-bit, non-prefetchable) [size=256K]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
00:02.1 Display controller [0380]: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller [8086:27a6] (rev 03)
Subsystem: Intel Corporation Device [8086:7270]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at 90300000 (32-bit, non-prefetchable) [size=512K]
Capabilities: <access denied>
00:07.0 Performance counters [1101]: Intel Corporation Device [8086:27a3] (rev 03)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 90444000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
00:1b.0 Audio device [0403]: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller [8086:27d8] (rev 02)
Subsystem: SigmaTel Device [8384:7680]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 256 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at 90440000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
00:1c.0 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 [8086:27d0] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 256 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00001000-00001fff
Memory behind bridge: 90200000-902fffff
Prefetchable memory behind bridge: 0000000090500000-00000000905fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1c.1 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 [8086:27d2] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 256 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Memory behind bridge: 90100000-901fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1d.0 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 [8086:27c8] (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device [8086:7270]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 21
Region 4: I/O ports at 2080 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 [8086:27c9] (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device [8086:7270]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 2060 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 [8086:27ca] (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device [8086:7270]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 2040 [size=32]
Kernel driver in use: uhci_hcd
00:1d.3 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 [8086:27cb] (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device [8086:7270]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at 2020 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller [8086:27cc] (rev 02) (prog-if 20 [EHCI])
Subsystem: Intel Corporation Device [8086:7270]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 21
Region 0: Memory at 90445400 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
Memory behind bridge: 90000000-900fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge [8086:27b9] (rev 02)
Subsystem: Intel Corporation Device [8086:7270]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.1 IDE interface [0101]: Intel Corporation 82801G (ICH7 Family) IDE Controller [8086:27df] (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Intel Corporation Device [8086:7270]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 20b0 [size=16]
Kernel driver in use: PIIX_IDE
00:1f.2 IDE interface [0101]: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller [8086:27c4] (rev 02) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Intel Corporation Device [8086:7270]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at 20c8 [size=8]
Region 1: I/O ports at 20ec [size=4]
Region 2: I/O ports at 20c0 [size=8]
Region 3: I/O ports at 20e8 [size=4]
Region 4: I/O ports at 20a0 [size=16]
Region 5: Memory at 90445000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ata_piix
00:1f.3 SMBus [0c05]: Intel Corporation 82801G (ICH7 Family) SMBus Controller [8086:27da] (rev 02)
Subsystem: Intel Corporation Device [8086:7270]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at efa0 [size=32]
Kernel driver in use: i801_smbus
01:00.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8053 PCI-E Gigabit Ethernet Controller [11ab:4362] (rev 22)
Subsystem: Technical Corp. Device [1234:5678]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 256 bytes
Interrupt: pin A routed to IRQ 26
Region 0: Memory at 90200000 (64-bit, non-prefetchable) [size=16K]
Region 2: I/O ports at 1000 [size=256]
Expansion ROM at 90500000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: sky2
02:00.0 Network controller [0280]: Atheros Communications Inc. AR5008 Wireless Network Adapter [168c:0024] (rev 01)
Subsystem: Apple Computer Inc. Device [106b:0087]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 256 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at 90100000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: ath9k
03:03.0 FireWire (IEEE 1394) [0c00]: Agere Systems FW322/323 [11c1:5811] (rev 61) (prog-if 10 [OHCI])
Subsystem: Agere Systems FW322/323 [11c1:5811]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B+ DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 248 (3000ns min, 6000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at 90000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
-- System Information:
Debian Release: squeeze/sid
APT prefers unstable
APT policy: (500, 'unstable')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.29-2-amd64 (SMP w/2 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.29-2-amd64 depends on:
ii debconf [debconf-2.0] 1.5.26 Debian configuration management sy
ii initramfs-tools [linux-initra 0.93.3 tools for generating an initramfs
ii module-init-tools 3.7-pre9-1 tools for managing Linux kernel mo
linux-image-2.6.29-2-amd64 recommends no packages.
Versions of packages linux-image-2.6.29-2-amd64 suggests:
ii grub 0.97-53 GRand Unified Bootloader (Legacy v
pn linux-doc-2.6.29 <none> (no description available)
-- debconf information:
linux-image-2.6.29-2-amd64/preinst/abort-install-2.6.29-2-amd64:
linux-image-2.6.29-2-amd64/preinst/lilo-has-ramdisk:
linux-image-2.6.29-2-amd64/preinst/initrd-2.6.29-2-amd64:
linux-image-2.6.29-2-amd64/preinst/abort-overwrite-2.6.29-2-amd64:
linux-image-2.6.29-2-amd64/preinst/overwriting-modules-2.6.29-2-amd64: true
linux-image-2.6.29-2-amd64/postinst/bootloader-error-2.6.29-2-amd64:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.29-2-amd64/postinst/old-initrd-link-2.6.29-2-amd64: true
linux-image-2.6.29-2-amd64/preinst/failed-to-move-modules-2.6.29-2-amd64:
linux-image-2.6.29-2-amd64/postinst/old-system-map-link-2.6.29-2-amd64: true
linux-image-2.6.29-2-amd64/preinst/elilo-initrd-2.6.29-2-amd64: true
linux-image-2.6.29-2-amd64/prerm/would-invalidate-boot-loader-2.6.29-2-amd64: true
linux-image-2.6.29-2-amd64/postinst/create-kimage-link-2.6.29-2-amd64: true
linux-image-2.6.29-2-amd64/prerm/removing-running-kernel-2.6.29-2-amd64: true
linux-image-2.6.29-2-amd64/postinst/old-dir-initrd-link-2.6.29-2-amd64: true
linux-image-2.6.29-2-amd64/postinst/kimage-is-a-directory:
linux-image-2.6.29-2-amd64/postinst/depmod-error-2.6.29-2-amd64: false
linux-image-2.6.29-2-amd64/postinst/bootloader-test-error-2.6.29-2-amd64:
linux-image-2.6.29-2-amd64/preinst/lilo-initrd-2.6.29-2-amd64: true
linux-image-2.6.29-2-amd64/preinst/bootloader-initrd-2.6.29-2-amd64: true
linux-image-2.6.29-2-amd64/postinst/depmod-error-initrd-2.6.29-2-amd64: false
Reply to: