Bug#520232: linux-image-2.6.28-1-amd64: have to load pcspkr to disable the pc speaker
Package: linux-image-2.6.28-1-amd64
Version: 2.6.28-1
Severity: normal
Upgrading from 2.6.26 to 2.6.28 the pc speaker started doing annoying
beeps when eg, tab-completing. To avoid this I used to blacklist pcspkr,
but now it seems I have to load it.
In summary: pc speaker on when the pcspkr module unloaded, off when the
module is loaded.
-- Package-specific info:
** Version:
Linux version 2.6.28-1-amd64 (Debian 2.6.28-1) (maks@debian.org) (gcc version 4.3.3 (Debian 4.3.3-4) ) #1 SMP Wed Feb 18 17:16:12 UTC 2009
** Command line:
BOOT_IMAGE=/boot/vmlinuz-2.6.28-1-amd64 root=UUID=1a73bf6e-7db2-4013-b64d-0898a5a8d0d7 ro quiet
** Not tainted
** Kernel log:
[152778.128284] ahci 0000:00:1f.2: restoring config space at offset 0x1 (was 0x2b00000, writing 0x2b00407)
[152778.128330] ahci 0000:00:1f.2: setting latency timer to 64
[152778.128379] i801_smbus 0000:00:1f.3: restoring config space at offset 0xf (was 0x200, writing 0x20a)
[152778.128412] i801_smbus 0000:00:1f.3: restoring config space at offset 0x4 (was 0x0, writing 0xfe9fb700)
[152778.128423] i801_smbus 0000:00:1f.3: restoring config space at offset 0x1 (was 0x2800001, writing 0x2800103)
[152778.144332] tg3 0000:09:00.0: restoring config space at offset 0xc (was 0x0, writing 0xfffb0000)
[152778.144391] tg3 0000:09:00.0: restoring config space at offset 0x3 (was 0x0, writing 0x10)
[152778.144408] tg3 0000:09:00.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100106)
[152778.160242] firewire_ohci 0000:03:01.0: restoring config space at offset 0xf (was 0x4020100, writing 0x4020105)
[152778.160272] firewire_ohci 0000:03:01.0: restoring config space at offset 0x3 (was 0x800000, writing 0x804010)
[152778.160281] firewire_ohci 0000:03:01.0: restoring config space at offset 0x1 (was 0x2100000, writing 0x2100106)
[152778.256241] sdhci-pci 0000:03:01.1: restoring config space at offset 0xf (was 0x200, writing 0x204)
[152778.256269] sdhci-pci 0000:03:01.1: restoring config space at offset 0x4 (was 0x0, writing 0xfe4ff500)
[152778.256276] sdhci-pci 0000:03:01.1: restoring config space at offset 0x3 (was 0x800000, writing 0x804010)
[152778.256285] sdhci-pci 0000:03:01.1: restoring config space at offset 0x1 (was 0x2100000, writing 0x2100106)
[152778.256304] sdhci-pci 0000:03:01.1: PCI INT B -> GSI 18 (level, low) -> IRQ 18
[152778.257325] pci 0000:03:01.2: restoring config space at offset 0xf (was 0x200, writing 0x204)
[152778.257346] pci 0000:03:01.2: restoring config space at offset 0x4 (was 0x0, writing 0xfe4ff600)
[152778.257351] pci 0000:03:01.2: restoring config space at offset 0x3 (was 0x800000, writing 0x804010)
[152778.257358] pci 0000:03:01.2: restoring config space at offset 0x1 (was 0x2100000, writing 0x2100106)
[152778.257378] pci 0000:03:01.3: restoring config space at offset 0xf (was 0x200, writing 0x204)
[152778.257400] pci 0000:03:01.3: restoring config space at offset 0x4 (was 0x0, writing 0xfe4ff700)
[152778.257405] pci 0000:03:01.3: restoring config space at offset 0x3 (was 0x800000, writing 0x804010)
[152778.257412] pci 0000:03:01.3: restoring config space at offset 0x1 (was 0x2100000, writing 0x2100106)
[152778.448250] ata3: SATA link down (SStatus 0 SControl 300)
[152778.568273] sd 0:0:0:0: [sda] Starting disk
[152779.009244] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[152779.042671] ata1.00: configured for UDMA/133
[152779.042865] sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors: (120 GB/111 GiB)
[152779.042890] sd 0:0:0:0: [sda] Write Protect is off
[152779.042894] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[152779.042929] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[152779.050687] hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
[152779.051647] hda: UDMA/33 mode selected
[152779.052713] pci 0000:00:02.0: setting latency timer to 64
[152779.300250] pm_op(): usb_dev_resume+0x0/0x5 returns -19
[152779.300253] PM: Device 1-2 failed to resume: error -19
[152779.300261] pm_op(): usb_dev_resume+0x0/0x5 returns -19
[152779.300264] PM: Device 1-2.1 failed to resume: error -19
[152779.300278] pm_op(): usb_dev_resume+0x0/0x5 returns -19
[152779.300281] PM: Device 1-2.2 failed to resume: error -19
[152779.300291] pm_op(): usb_dev_resume+0x0/0x5 returns -19
[152779.300294] PM: Device 1-2.3 failed to resume: error -19
[152779.300932] Restarting tasks ... <6>usb 1-2: USB disconnect, address 29
[152779.338508] usb 1-2.1: USB disconnect, address 30
[152779.338908] usb 1-2.2: USB disconnect, address 31
[152779.339009] done.
[152779.393287] usb 1-2.3: USB disconnect, address 32
[152781.388298] tg3 0000:09:00.0: irq 4346 for MSI/MSI-X
[152781.441717] ADDRCONF(NETDEV_UP): eth0: link is not ready
[152781.462188] iwl3945 0000:0c:00.0: enabling device (0000 -> 0002)
[152781.462201] iwl3945 0000:0c:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[152781.462276] iwl3945 0000:0c:00.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[152781.462351] iwl3945 0000:0c:00.0: restoring config space at offset 0x4 (was 0x0, writing 0xfe8ff000)
[152781.462364] iwl3945 0000:0c:00.0: restoring config space at offset 0x3 (was 0x0, writing 0x10)
[152781.462383] iwl3945 0000:0c:00.0: restoring config space at offset 0x1 (was 0x100002, writing 0x100106)
[152781.462567] iwl3945 0000:0c:00.0: irq 4345 for MSI/MSI-X
[152781.484182] CE: hpet increasing min_delta_ns to 75936 nsec
[152781.547603] Registered led device: iwl-phy0:radio
[152781.547645] Registered led device: iwl-phy0:assoc
[152781.547669] Registered led device: iwl-phy0:RX
[152781.547692] Registered led device: iwl-phy0:TX
[152781.604601] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[152855.853096] wlan0: authenticate with AP 00:1e:58:bb:1e:55
[152855.858758] wlan0: authenticated
[152855.858766] wlan0: associate with AP 00:1e:58:bb:1e:55
[152855.861928] wlan0: RX AssocResp from 00:1e:58:bb:1e:55 (capab=0x431 status=0 aid=2)
[152855.861935] wlan0: associated
[152855.882416] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[152875.624023] wlan0: no IPv6 routers present
[154696.976167] usb 1-2: new full speed USB device using uhci_hcd and address 33
[154697.161321] usb 1-2: configuration #1 chosen from 1 choice
[154697.164970] hub 1-2:1.0: USB hub found
[154697.170201] hub 1-2:1.0: 3 ports detected
[154697.175455] usb 1-2: New USB device found, idVendor=0a5c, idProduct=4500
[154697.175462] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[154697.175468] usb 1-2: Product: BCM2045B2
[154697.175472] usb 1-2: Manufacturer: Broadcom
[154697.449172] usb 1-2.1: new full speed USB device using uhci_hcd and address 34
[154697.577449] usb 1-2.1: configuration #1 chosen from 1 choice
[154697.581137] usb 1-2.1: New USB device found, idVendor=413c, idProduct=8126
[154697.581144] usb 1-2.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[154697.581150] usb 1-2.1: Product: BCM2045
[154697.581154] usb 1-2.1: Manufacturer: Broadcom Corp
[154697.705545] usb 1-2.2: new full speed USB device using uhci_hcd and address 35
[154697.844894] usb 1-2.2: configuration #1 chosen from 1 choice
[154697.854055] input: Broadcom Corp as /devices/pci0000:00/0000:00:1a.0/usb1/1-2/1-2.2/1-2.2:1.0/input/input34
[154697.889177] generic-usb 0003:0A5C:4502.0018: input,hidraw0: USB HID v1.11 Keyboard [Broadcom Corp] on usb-0000:00:1a.0-2.2/input0
[154697.889285] usb 1-2.2: New USB device found, idVendor=0a5c, idProduct=4502
[154697.889288] usb 1-2.2: New USB device strings: Mfr=1, Product=0, SerialNumber=0
[154697.889290] usb 1-2.2: Manufacturer: Broadcom Corp
[154697.973147] usb 1-2.3: new full speed USB device using uhci_hcd and address 36
[154698.113263] usb 1-2.3: configuration #1 chosen from 1 choice
[154698.123966] input: Broadcom Corp as /devices/pci0000:00/0000:00:1a.0/usb1/1-2/1-2.3/1-2.3:1.0/input/input35
[154698.156264] generic-usb 0003:0A5C:4503.0019: input,hidraw1: USB HID v1.11 Mouse [Broadcom Corp] on usb-0000:00:1a.0-2.3/input0
[154698.156520] usb 1-2.3: New USB device found, idVendor=0a5c, idProduct=4503
[154698.156527] usb 1-2.3: New USB device strings: Mfr=1, Product=0, SerialNumber=0
[154698.156533] usb 1-2.3: Manufacturer: Broadcom Corp
[159012.870454] jackd[2551]: segfault at 90 ip 00007f4e82add588 sp 00007fff8b33e1c0 error 4 in libpthread-2.9.so[7f4e82ad6000+16000]
[161790.170369] input: PC Speaker as /devices/platform/pcspkr/input/input36
** Loaded modules:
Module Size Used by
pcspkr 68352 0
iwl3945 152680 0
rfkill 77504 2 iwl3945
mac80211 221616 1 iwl3945
led_class 70280 1 iwl3945
cfg80211 97440 2 iwl3945,mac80211
cpufreq_stats 70404 0
tun 76676 0
appletalk 96352 0
ax25 114968 0
ipx 89296 0
p8023 67584 1 ipx
mmc_block 75784 0
nls_utf8 67584 1
ntfs 250208 1
nls_base 74372 2 nls_utf8,ntfs
i915 123272 2
drm 167888 3 i915
ppdev 73096 0
parport_pc 92312 0
lp 75876 0
parport 103328 3 ppdev,parport_pc,lp
rfcomm 102304 0
hidp 81280 2
l2cap 86656 8 rfcomm,hidp
ipv6 348928 14
binfmt_misc 74892 1
fuse 117056 1
coretemp 72192 0
cpufreq_powersave 67328 0
cpufreq_userspace 69252 0
cpufreq_conservative 72712 0
acpi_cpufreq 74000 0
loop 80652 0
firewire_sbp2 80912 0
joydev 76544 0
snd_hda_intel 553796 1
snd_pcm_oss 102176 0
snd_mixer_oss 80256 1 snd_pcm_oss
snd_pcm 144264 2 snd_hda_intel,snd_pcm_oss
snd_seq_dummy 68740 0
snd_seq_oss 94272 0
snd_seq_midi 72256 0
snd_rawmidi 88480 1 snd_seq_midi
snd_seq_midi_event 73088 2 snd_seq_oss,snd_seq_midi
snd_seq 115568 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
dcdbas 73648 0
arc4 67584 2
ecb 68608 2
psmouse 106908 0
serio_raw 71428 0
i2c_i801 75292 0
i2c_core 90528 1 i2c_i801
iTCO_wdt 78032 0
snd_timer 87824 2 snd_pcm,snd_seq
snd_seq_device 73108 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
snd 125432 11 snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
soundcore 73488 1 snd
snd_page_alloc 75280 2 snd_hda_intel,snd_pcm
btusb 77976 0
evdev 76304 8
bluetooth 120740 4 rfcomm,hidp,l2cap,btusb
intel_agp 93936 1
wmi 73280 0
button 72992 0
battery 78088 0
video 86036 0
output 68992 1 video
ac 70664 0
ext3 186768 1
jbd 116264 1 ext3
mbcache 74628 1 ext3
ide_cd_mod 102544 0
cdrom 99112 1 ide_cd_mod
ide_pci_generic 70148 0
usbhid 98864 0
hid 107152 2 hidp,usbhid
sd_mod 97576 4
crc_t10dif 67712 1 sd_mod
piix 72712 0
ide_core 178284 3 ide_cd_mod,ide_pci_generic,piix
ahci 97932 4
ata_generic 71556 0
libata 237504 2 ahci,ata_generic
scsi_mod 229160 3 firewire_sbp2,sd_mod,libata
sdhci_pci 73472 0
sdhci 81924 1 sdhci_pci
mmc_core 117568 2 mmc_block,sdhci
firewire_ohci 88708 0
firewire_core 104256 2 firewire_sbp2,firewire_ohci
crc_itu_t 67840 1 firewire_core
tg3 165764 0
ehci_hcd 99852 0
uhci_hcd 87968 0
thermal 84384 1
processor 111544 4 acpi_cpufreq,thermal
fan 70920 1
thermal_sys 78656 4 video,thermal,processor,fan
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub [8086:2a00] (rev 0c)
Subsystem: Dell Inspiron 1420 [1028:01f3]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
Kernel modules: intel-agp
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller [8086:2a02] (rev 0c) (prog-if 00 [VGA controller])
Subsystem: Dell Inspiron 1420 [1028:01f3]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 4344
Region 0: Memory at fea00000 (64-bit, non-prefetchable) [size=1M]
Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at eff8 [size=8]
Capabilities: <access denied>
Kernel modules: intelfb
00:02.1 Display controller [0380]: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller [8086:2a03] (rev 0c)
Subsystem: Dell Dell Inspiron 1420 [1028:01f3]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at feb00000 (64-bit, non-prefetchable) [size=1M]
Capabilities: <access denied>
00:1a.0 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 [8086:2834] (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Inspiron 1420 [1028:01f3]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 6f20 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.1 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 [8086:2835] (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Inspiron 1420 [1028:01f3]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at 6f00 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.7 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 [8086:283a] (rev 02) (prog-if 20 [EHCI])
Subsystem: Dell Inspiron 1420 [1028:01f3]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 22
Region 0: Memory at fed1c400 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1b.0 Audio device [0403]: Intel Corporation 82801H (ICH8 Family) HD Audio Controller [8086:284b] (rev 02)
Subsystem: Dell Inspiron 1420 [1028:01f3]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at fe9fc000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:1c.0 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 [8086:283f] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0b, subordinate=0b, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.1 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 [8086:2841] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0c, subordinate=0c, sec-latency=0
Memory behind bridge: fe800000-fe8fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.3 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 4 [8086:2845] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0d, subordinate=0e, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fe600000-fe7fffff
Prefetchable memory behind bridge: 00000000f0000000-00000000f01fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.5 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 6 [8086:2849] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=09, subordinate=09, sec-latency=0
Memory behind bridge: fe500000-fe5fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1d.0 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 [8086:2830] (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Inspiron 1420 [1028:01f3]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 6f80 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 [8086:2831] (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Inspiron 1420 [1028:01f3]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at 6f60 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 [8086:2832] (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Inspiron 1420 [1028:01f3]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 22
Region 4: I/O ports at 6f40 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 [8086:2836] (rev 02) (prog-if 20 [EHCI])
Subsystem: Dell Inspiron 1420 [1028:01f3]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 0: Memory at fed1c000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev f2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
Memory behind bridge: fe400000-fe4fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller [8086:2815] (rev 02)
Subsystem: Dell Inspiron 1420 [1028:01f3]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel modules: iTCO_wdt
00:1f.1 IDE interface [0101]: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller [8086:2850] (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Dell Inspiron 1420 [1028:01f3]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 6fa0 [size=16]
Kernel driver in use: PIIX_IDE
Kernel modules: ide-pci-generic, piix, ata_generic
00:1f.2 SATA controller [0106]: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller [8086:2829] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Dell Device [1028:01f3]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 4347
Region 0: I/O ports at 6eb0 [size=8]
Region 1: I/O ports at 6eb8 [size=4]
Region 2: I/O ports at 6ec0 [size=8]
Region 3: I/O ports at 6ec8 [size=4]
Region 4: I/O ports at 6ee0 [size=32]
Region 5: Memory at fe9fb800 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
Kernel modules: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 82801H (ICH8 Family) SMBus Controller [8086:283e] (rev 02)
Subsystem: Dell Inspiron 1420 [1028:01f3]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 17
Region 0: Memory at fe9fb700 (32-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 10c0 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801
03:01.0 FireWire (IEEE 1394) [0c00]: Ricoh Co Ltd R5C832 IEEE 1394 Controller [1180:0832] (rev 05) (prog-if 10 [OHCI])
Subsystem: Dell Device [1028:01f3]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (500ns min, 1000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at fe4ff800 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
Kernel modules: firewire-ohci
03:01.1 SD Host controller [0805]: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter [1180:0822] (rev 22) (prog-if 01)
Subsystem: Dell Device [1028:01f3]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 18
Region 0: Memory at fe4ff500 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: sdhci-pci
Kernel modules: sdhci-pci
03:01.2 System peripheral [0880]: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter [1180:0592] (rev 12)
Subsystem: Dell Device [1028:01f3]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 4
Region 0: Memory at fe4ff600 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
03:01.3 System peripheral [0880]: Ricoh Co Ltd xD-Picture Card Controller [1180:0852] (rev 12)
Subsystem: Dell Device [1028:01f3]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 4
Region 0: Memory at fe4ff700 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
09:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM5906M Fast Ethernet PCI Express [14e4:1713] (rev 02)
Subsystem: Dell Inspiron 1420 [1028:01f3]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 4346
Region 0: Memory at fe5f0000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at <ignored> [disabled]
Capabilities: <access denied>
Kernel driver in use: tg3
Kernel modules: tg3
0c:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection [8086:4222] (rev 02)
Subsystem: Intel Corporation Device [8086:1020]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 4345
Region 0: Memory at fe8ff000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: iwl3945
Kernel modules: iwl3945
-- System Information:
Debian Release: 5.0
APT prefers unstable
APT policy: (500, 'unstable')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.28-1-amd64 (SMP w/2 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.28-1-amd64 depends on:
ii debconf [debconf-2.0] 1.5.24 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92o tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
linux-image-2.6.28-1-amd64 recommends no packages.
Versions of packages linux-image-2.6.28-1-amd64 suggests:
ii grub-pc [grub] 1.96+20080724-14 GRand Unified Bootloader, version
pn linux-doc-2.6.28 <none> (no description available)
-- debconf information:
linux-image-2.6.28-1-amd64/postinst/depmod-error-initrd-2.6.28-1-amd64: false
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.28-1-amd64/postinst/bootloader-error-2.6.28-1-amd64:
linux-image-2.6.28-1-amd64/postinst/depmod-error-2.6.28-1-amd64: false
linux-image-2.6.28-1-amd64/postinst/bootloader-test-error-2.6.28-1-amd64:
linux-image-2.6.28-1-amd64/postinst/old-system-map-link-2.6.28-1-amd64: true
linux-image-2.6.28-1-amd64/preinst/initrd-2.6.28-1-amd64:
linux-image-2.6.28-1-amd64/preinst/bootloader-initrd-2.6.28-1-amd64: true
linux-image-2.6.28-1-amd64/postinst/old-initrd-link-2.6.28-1-amd64: true
linux-image-2.6.28-1-amd64/postinst/old-dir-initrd-link-2.6.28-1-amd64: true
linux-image-2.6.28-1-amd64/preinst/failed-to-move-modules-2.6.28-1-amd64:
linux-image-2.6.28-1-amd64/preinst/elilo-initrd-2.6.28-1-amd64: true
linux-image-2.6.28-1-amd64/preinst/lilo-initrd-2.6.28-1-amd64: true
linux-image-2.6.28-1-amd64/preinst/overwriting-modules-2.6.28-1-amd64: true
linux-image-2.6.28-1-amd64/preinst/lilo-has-ramdisk:
linux-image-2.6.28-1-amd64/preinst/abort-overwrite-2.6.28-1-amd64:
linux-image-2.6.28-1-amd64/preinst/abort-install-2.6.28-1-amd64:
linux-image-2.6.28-1-amd64/postinst/kimage-is-a-directory:
linux-image-2.6.28-1-amd64/postinst/create-kimage-link-2.6.28-1-amd64: true
linux-image-2.6.28-1-amd64/prerm/removing-running-kernel-2.6.28-1-amd64: true
linux-image-2.6.28-1-amd64/prerm/would-invalidate-boot-loader-2.6.28-1-amd64: true
Reply to: