Bug#517241: linux-image-2.6.28-1-amd64: Audio (Intel Corporation 82801H (ICH8 Family)) broken
Package: linux-image-2.6.28-1-amd64
Version: 2.6.28-1
Severity: normal
Under the 2.6.28 kernel, audio does not work properly on my laptop.
If I plug in some headphones, audio still comes out of the main laptop
speakers. Audio out of the headphone port is very quiet, and adjusting the
volume does not make it any louder or quieter (though it does affect the main
laptop speakers as normal).
00:1b.0 Audio device [0403]: Intel Corporation 82801H (ICH8 Family) HD Audio Controller [8086:284b] (rev 03)
Subsystem: Samsung Electronics Co Ltd Device [144d:c510]
Flags: bus master, fast devsel, latency 0, IRQ 22
Memory at f0500000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
-- Package-specific info:
** Version:
Linux version 2.6.28-1-amd64 (Debian 2.6.28-1) (maks@debian.org) (gcc version 4.3.3 (Debian 4.3.3-4) ) #1 SMP Wed Feb 18 17:16:12 UTC 2009
** Command line:
BOOT_IMAGE=/boot/vmlinuz-2.6.28-1-amd64 root=/dev/mapper/durandal-root ro quiet
** Not tainted
** Kernel log:
[40699.496107] sky2 0000:03:00.0: restoring config space at offset 0x6 (was 0x1, writing 0x2001)
[40699.496119] sky2 0000:03:00.0: restoring config space at offset 0x4 (was 0x4, writing 0xf0200004)
[40699.496128] sky2 0000:03:00.0: restoring config space at offset 0x3 (was 0x0, writing 0x10)
[40699.496140] sky2 0000:03:00.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100507)
[40699.496322] yenta_cardbus 0000:04:09.0: power state changed by ACPI to D0
[40699.496335] yenta_cardbus 0000:04:09.0: restoring config space at offset 0xf (was 0x7000100, writing 0x58001ff)
[40699.496341] yenta_cardbus 0000:04:09.0: restoring config space at offset 0xe (was 0x0, writing 0x34fc)
[40699.496347] yenta_cardbus 0000:04:09.0: restoring config space at offset 0xd (was 0x0, writing 0x3400)
[40699.496353] yenta_cardbus 0000:04:09.0: restoring config space at offset 0xc (was 0x0, writing 0x30fc)
[40699.496358] yenta_cardbus 0000:04:09.0: restoring config space at offset 0xb (was 0x0, writing 0x3000)
[40699.496364] yenta_cardbus 0000:04:09.0: restoring config space at offset 0xa (was 0x0, writing 0x93fff000)
[40699.496370] yenta_cardbus 0000:04:09.0: restoring config space at offset 0x9 (was 0x0, writing 0x90000000)
[40699.496376] yenta_cardbus 0000:04:09.0: restoring config space at offset 0x8 (was 0x0, writing 0x8bfff000)
[40699.496382] yenta_cardbus 0000:04:09.0: restoring config space at offset 0x7 (was 0x0, writing 0x88000000)
[40699.496388] yenta_cardbus 0000:04:09.0: restoring config space at offset 0x6 (was 0x0, writing 0xb0080504)
[40699.496395] yenta_cardbus 0000:04:09.0: restoring config space at offset 0x4 (was 0x0, writing 0xf0400000)
[40699.496401] yenta_cardbus 0000:04:09.0: restoring config space at offset 0x3 (was 0x824000, writing 0x82a800)
[40699.636125] firewire_ohci 0000:04:09.1: power state changed by ACPI to D0
[40699.636142] firewire_ohci 0000:04:09.1: restoring config space at offset 0xf (was 0x4020200, writing 0x40202ff)
[40699.636171] firewire_ohci 0000:04:09.1: restoring config space at offset 0x4 (was 0x0, writing 0xf0401000)
[40699.636184] firewire_ohci 0000:04:09.1: restoring config space at offset 0x1 (was 0x2100000, writing 0x2100106)
[40699.716179] sdhci-pci 0000:04:09.2: power state changed by ACPI to D0
[40699.716196] sdhci-pci 0000:04:09.2: restoring config space at offset 0xf (was 0x300, writing 0x3ff)
[40699.716224] sdhci-pci 0000:04:09.2: restoring config space at offset 0x4 (was 0x0, writing 0xf0401800)
[40699.716232] sdhci-pci 0000:04:09.2: restoring config space at offset 0x3 (was 0x800000, writing 0x802000)
[40699.716248] sdhci-pci 0000:04:09.2: restoring config space at offset 0x1 (was 0x2100000, writing 0x2100106)
[40699.716310] sdhci-pci 0000:04:09.2: power state changed by ACPI to D0
[40699.716317] sdhci-pci 0000:04:09.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22
[40699.716321] sdhci-pci 0000:04:09.2: Will use DMA mode even though HW doesn't fully claim to support it.
[40699.716333] ricoh-mmc: Resuming.
[40699.716347] ricoh-mmc: Controller is now disabled.
[40699.716360] pci 0000:04:09.4: restoring config space at offset 0xf (was 0x300, writing 0x3ff)
[40699.716383] pci 0000:04:09.4: restoring config space at offset 0x4 (was 0x0, writing 0xf0402400)
[40699.716392] pci 0000:04:09.4: restoring config space at offset 0x1 (was 0x2100000, writing 0x2100102)
[40700.152521] ata2.00: ACPI cmd ef/03:0c:00:00:00:a0 filtered out
[40700.152524] ata2.00: ACPI cmd ef/03:42:00:00:00:a0 filtered out
[40700.168464] ata2.00: configured for UDMA/33
[40700.484044] usb 6-2: reset high speed USB device using ehci_hcd and address 2
[40700.671989] sd 0:0:0:0: [sda] Starting disk
[40700.992314] ata1.00: ACPI cmd ef/03:01:00:00:00:a0 filtered out
[40700.992317] ata1.00: ACPI cmd ef/03:45:00:00:00:a0 filtered out
[40701.008338] ata1.00: configured for UDMA/100
[40701.030096] sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors: (250 GB/232 GiB)
[40701.030128] sd 0:0:0:0: [sda] Write Protect is off
[40701.030132] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[40701.030178] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[40701.140053] usb 7-2: reset high speed USB device using ehci_hcd and address 2
[40701.740362] usb 7-2.1: reset low speed USB device using ehci_hcd and address 4
[40702.284367] usb 7-2.2: reset low speed USB device using ehci_hcd and address 5
[40702.680042] usb 5-1: reset full speed USB device using uhci_hcd and address 2
[40702.852086] pci 0000:00:02.0: setting latency timer to 64
[40702.858747] Restarting tasks ... done.
[40702.988365] usb 7-2.3: reset high speed USB device using ehci_hcd and address 6
[40703.186564] sky2 eth0: enabling interface
[40703.186900] ADDRCONF(NETDEV_UP): eth0: link is not ready
[40703.188754] iwl3945 0000:02:00.0: enabling device (0000 -> 0002)
[40703.188771] iwl3945 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[40703.188841] iwl3945 0000:02:00.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[40703.188911] iwl3945 0000:02:00.0: restoring config space at offset 0x4 (was 0x0, writing 0xf0300000)
[40703.188925] iwl3945 0000:02:00.0: restoring config space at offset 0x3 (was 0x0, writing 0x10)
[40703.188944] iwl3945 0000:02:00.0: restoring config space at offset 0x1 (was 0x100002, writing 0x100106)
[40703.189148] iwl3945 0000:02:00.0: irq 4348 for MSI/MSI-X
[40703.290504] Registered led device: iwl-phy0:radio
[40703.290556] Registered led device: iwl-phy0:assoc
[40703.290576] Registered led device: iwl-phy0:RX
[40703.290595] Registered led device: iwl-phy0:TX
[40703.340446] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[40703.368015] wlan0: direct probe to AP 00:18:84:23:b7:f1 try 1
[40703.475267] wlan0: direct probe to AP 00:18:84:23:b7:f1 try 1
[40703.481044] wlan0 direct probe responded
[40703.481048] wlan0: authenticate with AP 00:18:84:23:b7:f1
[40703.483044] wlan0: authenticated
[40703.483047] wlan0: associate with AP 00:18:84:23:b7:f1
[40703.485644] wlan0: RX AssocResp from 00:18:84:23:b7:f1 (capab=0x421 status=0 aid=1)
[40703.485647] wlan0: associated
[40703.505400] wlan0: disassociating by local choice (reason=3)
[40704.595262] wlan0: deauthenticated
[40704.943041] sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both
[40704.943548] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[40715.632030] eth0: no IPv6 routers present
[46108.262288] fbodrawbuffers[23807]: segfault at 1b0 ip 00007f79e7e9b059 sp 00007ffff30b7650 error 4 in i965_dri.so[7f79e7e59000+278000]
[47219.603656] winevdm.exe: vm86 mode not supported on 64 bit kernel
[54786.731066] warning: `VirtualBox' uses 32-bit capabilities (legacy support in use)
[55900.487487] vboxdrv: Trying to deactivate the NMI watchdog permanently...
[55900.487492] vboxdrv: Successfully done.
[55900.487496] vboxdrv: Found 2 processor cores.
[55900.487580] VBoxDrv: dbg - g_abExecMemory=ffffffffa0b75a60
[55900.487627] vboxdrv: fAsync=0 offMin=0x29e offMax=0xbd6
[55900.487696] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[55900.487701] vboxdrv: Successfully loaded version 2.1.2_OSE (interface 0x000a0009).
[55900.733809] VBoxNetFlt: dbg - g_abExecMemory=ffffffffa0d1fa60
[60415.255621] HDA Intel 0000:00:1b.0: PCI INT A disabled
[60513.702064] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[60513.702253] HDA Intel 0000:00:1b.0: setting latency timer to 64
[60536.782638] HDA Intel 0000:00:1b.0: PCI INT A disabled
[60542.895635] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[60542.895738] HDA Intel 0000:00:1b.0: setting latency timer to 64
[60543.703415] HDA Intel 0000:00:1b.0: PCI INT A disabled
[60544.659250] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[60544.659351] HDA Intel 0000:00:1b.0: setting latency timer to 64
** Loaded modules:
Module Size Used by
snd_hda_intel 553796 1
vboxnetflt 151132 0
vboxdrv 1745788 1 vboxnetflt
snd_seq_dummy 68740 0
nls_utf8 67584 0
nls_cp437 72448 0
vfat 76288 0
fat 115384 1 vfat
nls_base 74372 4 nls_utf8,nls_cp437,vfat,fat
usb_storage 162848 0
video 86036 0
output 68992 1 video
i915 123272 2
drm 167888 3 i915
binfmt_misc 74892 1
rfcomm 102304 2
l2cap 86656 9 rfcomm
ppdev 73096 0
parport_pc 92312 0
lp 75876 0
parport 103328 3 ppdev,parport_pc,lp
ipv6 348928 40
acpi_cpufreq 74000 0
cpufreq_powersave 67328 0
cpufreq_conservative 72712 0
cpufreq_stats 70404 0
cpufreq_userspace 69252 0
sha256_generic 74880 0
aes_x86_64 73728 2
aes_generic 93480 1 aes_x86_64
cbc 69376 1
dm_crypt 78344 1
loop 80652 0
firewire_sbp2 80912 0
joydev 76544 0
pcmcia 101016 0
serio_raw 71428 0
pcspkr 68352 0
psmouse 106908 0
i2c_i801 75292 0
i2c_core 90528 1 i2c_i801
iTCO_wdt 78032 0
arc4 67584 2
evdev 76304 17
ecb 68608 2
yenta_socket 90508 1
rsrc_nonstatic 75520 1 yenta_socket
pcmcia_core 101924 3 pcmcia,yenta_socket,rsrc_nonstatic
hid_cherry 68352 0
snd_pcm 144264 1 snd_hda_intel
snd_seq 115568 1 snd_seq_dummy
iwl3945 152680 0
snd_timer 87824 2 snd_pcm,snd_seq
snd_seq_device 73108 2 snd_seq_dummy,snd_seq
rfkill 77504 2 iwl3945
bluetooth 120740 4 rfcomm,l2cap
mac80211 221616 1 iwl3945
snd 125432 7 snd_hda_intel,snd_pcm,snd_seq,snd_timer,snd_seq_device
led_class 70280 1 iwl3945
soundcore 73488 1 snd
cfg80211 97440 2 iwl3945,mac80211
snd_page_alloc 75280 2 snd_hda_intel,snd_pcm
uvcvideo 119048 0
compat_ioctl32 73728 1 uvcvideo
videodev 99712 2 uvcvideo,compat_ioctl32
v4l1_compat 78084 2 uvcvideo,videodev
intel_agp 93936 1
wmi 73280 0
battery 78088 0
button 72992 0
ac 70664 0
ext3 186768 2
jbd 116264 1 ext3
mbcache 74628 1 ext3
dm_mirror 79488 0
dm_region_hash 78208 1 dm_mirror
dm_log 75524 2 dm_mirror,dm_region_hash
dm_snapshot 81992 0
dm_mod 121184 12 dm_crypt,dm_mirror,dm_log,dm_snapshot
usbhid 98864 0
hid 107152 2 hid_cherry,usbhid
sg 94928 0
sr_mod 80948 0
cdrom 99112 1 sr_mod
sd_mod 97576 2
crc_t10dif 67712 1 sd_mod
ata_piix 88836 1
ata_generic 71556 0
libata 237504 2 ata_piix,ata_generic
scsi_mod 229160 6 usb_storage,firewire_sbp2,sg,sr_mod,sd_mod,libata
ide_pci_generic 70148 0
ide_core 178284 1 ide_pci_generic
ricoh_mmc 69760 0
sdhci_pci 73472 0
sdhci 81924 1 sdhci_pci
firewire_ohci 88708 0
firewire_core 104256 2 firewire_sbp2,firewire_ohci
crc_itu_t 67840 1 firewire_core
mmc_core 117568 1 sdhci
sky2 113156 0
ehci_hcd 99852 0
uhci_hcd 87968 0
thermal 84384 0
processor 111544 4 acpi_cpufreq,thermal
fan 70920 0
thermal_sys 78656 4 video,thermal,processor,fan
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub [8086:2a00] (rev 03)
Subsystem: Samsung Electronics Co Ltd Device [144d:c510]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
Kernel modules: intel-agp
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller [8086:2a02] (rev 03) (prog-if 00 [VGA controller])
Subsystem: Samsung Electronics Co Ltd Device [144d:c510]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 4347
Region 0: Memory at f0000000 (64-bit, non-prefetchable) [size=1M]
Region 2: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at 1800 [size=8]
Capabilities: <access denied>
Kernel modules: intelfb
00:02.1 Display controller [0380]: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller [8086:2a03] (rev 03)
Subsystem: Samsung Electronics Co Ltd Device [144d:c510]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at f0100000 (64-bit, non-prefetchable) [size=1M]
Capabilities: <access denied>
00:1a.0 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 [8086:2834] (rev 03) (prog-if 00 [UHCI])
Subsystem: Samsung Electronics Co Ltd Device [144d:c510]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at 1820 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.1 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 [8086:2835] (rev 03) (prog-if 00 [UHCI])
Subsystem: Samsung Electronics Co Ltd Device [144d:c510]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at 1840 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.7 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 [8086:283a] (rev 03) (prog-if 20 [EHCI])
Subsystem: Samsung Electronics Co Ltd Device [144d:c510]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 0: Memory at f0704000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1b.0 Audio device [0403]: Intel Corporation 82801H (ICH8 Family) HD Audio Controller [8086:284b] (rev 03)
Subsystem: Samsung Electronics Co Ltd Device [144d:c510]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at f0500000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:1c.0 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 [8086:283f] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Memory behind bridge: f0300000-f03fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.1 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 [8086:2841] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: f0200000-f02fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1d.0 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 [8086:2830] (rev 03) (prog-if 00 [UHCI])
Subsystem: Samsung Electronics Co Ltd Device [144d:c510]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at 1860 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 [8086:2831] (rev 03) (prog-if 00 [UHCI])
Subsystem: Samsung Electronics Co Ltd Device [144d:c510]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 1880 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 [8086:2832] (rev 03) (prog-if 00 [UHCI])
Subsystem: Samsung Electronics Co Ltd Device [144d:c510]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 18a0 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 [8086:2836] (rev 03) (prog-if 20 [EHCI])
Subsystem: Samsung Electronics Co Ltd Device [144d:c510]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f0704400 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev f3) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=04, subordinate=08, sec-latency=32
I/O behind bridge: 00003000-00003fff
Memory behind bridge: f0400000-f04fffff
Prefetchable memory behind bridge: 0000000088000000-000000008bffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller [8086:2815] (rev 03)
Subsystem: Samsung Electronics Co Ltd Device [144d:c510]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel modules: iTCO_wdt
00:1f.2 IDE interface [0101]: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA IDE Controller [8086:2828] (rev 03) (prog-if 80 [Master])
Subsystem: Samsung Electronics Co Ltd Device [144d:c510]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 18e0 [size=16]
Region 5: I/O ports at 18d0 [size=16]
Capabilities: <access denied>
Kernel driver in use: ata_piix
Kernel modules: ide-pci-generic, ata_generic, ata_piix
00:1f.3 SMBus [0c05]: Intel Corporation 82801H (ICH8 Family) SMBus Controller [8086:283e] (rev 03)
Subsystem: Samsung Electronics Co Ltd Device [144d:c510]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 19
Region 0: Memory at 8c000000 (32-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 1c00 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801
02:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection [8086:4222] (rev 02)
Subsystem: Intel Corporation PRO/Wireless 3945BG Network Connection [8086:1034]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 4348
Region 0: Memory at f0300000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: iwl3945
Kernel modules: iwl3945
03:00.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8039 PCI-E Fast Ethernet Controller [11ab:4353] (rev 15)
Subsystem: Samsung Electronics Co Ltd Device [144d:c510]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 4349
Region 0: Memory at f0200000 (64-bit, non-prefetchable) [size=16K]
Region 2: I/O ports at 2000 [size=256]
Capabilities: <access denied>
Kernel driver in use: sky2
Kernel modules: sky2
04:09.0 CardBus bridge [0607]: Ricoh Co Ltd RL5c476 II [1180:0476] (rev b4)
Subsystem: Samsung Electronics Co Ltd Device [144d:c510]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168
Interrupt: pin A routed to IRQ 20
Region 0: Memory at f0400000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=04, secondary=05, subordinate=08, sec-latency=176
Memory window 0: 88000000-8bfff000 (prefetchable)
Memory window 1: 90000000-93fff000
I/O window 0: 00003000-000030ff
I/O window 1: 00003400-000034ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
Kernel modules: yenta_socket
04:09.1 FireWire (IEEE 1394) [0c00]: Ricoh Co Ltd R5C552 IEEE 1394 Controller [1180:0552] (rev 09) (prog-if 10 [OHCI])
Subsystem: Samsung Electronics Co Ltd Device [144d:c510]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (500ns min, 1000ns max)
Interrupt: pin B routed to IRQ 21
Region 0: Memory at f0401000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
Kernel modules: firewire-ohci
04:09.2 SD Host controller [0805]: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter [1180:0822] (rev 18)
Subsystem: Samsung Electronics Co Ltd Device [144d:c510]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin C routed to IRQ 22
Region 0: Memory at f0401800 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: sdhci-pci
Kernel modules: sdhci-pci
04:09.3 System peripheral [0880]: Ricoh Co Ltd R5C843 MMC Host Controller [1180:0843] (rev 09)
Subsystem: Samsung Electronics Co Ltd Device [144d:c510]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 255
Region 0: [virtual] Memory at f0401c00 (32-bit, non-prefetchable) [disabled] [size=256]
Capabilities: <access denied>
Kernel driver in use: ricoh-mmc
Kernel modules: ricoh_mmc
04:09.4 System peripheral [0880]: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter [1180:0592] (rev 04)
Subsystem: Samsung Electronics Co Ltd Device [144d:c510]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 255
Region 0: Memory at f0402000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
04:09.5 System peripheral [0880]: Ricoh Co Ltd xD-Picture Card Controller [1180:0852] (rev ff) (prog-if ff)
!!! Unknown header type 7f
-- System Information:
Debian Release: 5.0
APT prefers testing
APT policy: (530, 'testing'), (520, 'unstable'), (400, 'experimental')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.28-1-amd64 (SMP w/2 CPU cores)
Locale: LANG=en_GB.UTF-8, LC_CTYPE=en_GB.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.28-1-amd64 depends on:
ii debconf [debconf-2.0] 1.5.24 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92o tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
linux-image-2.6.28-1-amd64 recommends no packages.
Versions of packages linux-image-2.6.28-1-amd64 suggests:
ii grub-pc [grub] 1.96+20080724-16 GRand Unified Bootloader, version
ii linux-doc-2.6.28 2.6.28-1 Linux kernel specific documentatio
-- debconf information:
linux-image-2.6.28-1-amd64/postinst/depmod-error-initrd-2.6.28-1-amd64: false
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.28-1-amd64/postinst/bootloader-error-2.6.28-1-amd64:
linux-image-2.6.28-1-amd64/postinst/depmod-error-2.6.28-1-amd64: false
linux-image-2.6.28-1-amd64/postinst/bootloader-test-error-2.6.28-1-amd64:
linux-image-2.6.28-1-amd64/postinst/old-system-map-link-2.6.28-1-amd64: true
linux-image-2.6.28-1-amd64/preinst/initrd-2.6.28-1-amd64:
linux-image-2.6.28-1-amd64/preinst/bootloader-initrd-2.6.28-1-amd64: true
linux-image-2.6.28-1-amd64/postinst/old-initrd-link-2.6.28-1-amd64: true
linux-image-2.6.28-1-amd64/postinst/old-dir-initrd-link-2.6.28-1-amd64: true
linux-image-2.6.28-1-amd64/preinst/failed-to-move-modules-2.6.28-1-amd64:
linux-image-2.6.28-1-amd64/preinst/elilo-initrd-2.6.28-1-amd64: true
linux-image-2.6.28-1-amd64/preinst/lilo-initrd-2.6.28-1-amd64: true
linux-image-2.6.28-1-amd64/preinst/overwriting-modules-2.6.28-1-amd64: true
linux-image-2.6.28-1-amd64/preinst/lilo-has-ramdisk:
linux-image-2.6.28-1-amd64/preinst/abort-overwrite-2.6.28-1-amd64:
linux-image-2.6.28-1-amd64/preinst/abort-install-2.6.28-1-amd64:
linux-image-2.6.28-1-amd64/postinst/kimage-is-a-directory:
linux-image-2.6.28-1-amd64/postinst/create-kimage-link-2.6.28-1-amd64: true
linux-image-2.6.28-1-amd64/prerm/removing-running-kernel-2.6.28-1-amd64: true
linux-image-2.6.28-1-amd64/prerm/would-invalidate-boot-loader-2.6.28-1-amd64: true
Reply to: