Bug#517013: linux-image-2.6.26-1-686: Suspected PS/2 device problem causes system to hang
Package: linux-image-2.6.26-1-686
Version: 2.6.26-13
Severity: critical
Justification: breaks the whole system
Running Etch on this system for a year or two, I was lulled into a
comfort zone. :) I upgraded to Lenny, and the problems began. Randomly,
the displayed video would go 'kablooey' and the system would hang. I
also noticed the super I/O chip would heat up (the fan would speed up).
I unplugged a bunch of stuff to no avail. I finally unplugged
*everything* and the system would finally run POST OK. That's when I
realized it was probably related to PS/2.
The system is an Asus K8N-DL, 2 Opteron 270s, 2 1GB sticks of RAM,
GeForce 7600, PCI-E video, several SATA drives and a bunch of USB stuff,
as well as a Logitech MX3000 wireless kbd/mouse. It is powered through a
UPS and is unpowered each night.
As states, the system would boot, then hang a random time later. But in
the past day or so, the system got to where it wouldn't even POST. I saw
absolutely no error reports in anything in /var/log that seemed to be
related; the system simply hanged itself every time.
I had the MX's PS/2 mouse connector plugged into the mouse jack. I had
an empty USB-to-PS/2 adapter plugged into the kdb jack. Once I unplugged
both of these, the problems vanished. Historically, I had the PS/2
plugged in because Etch would not, or would not properly, utilize the
USB mouse. Once I unplugged these two things and the system returned to
normal operation, the dawn broke over ol' Marblehead here.
I don't know how this can be reproduced other than using faulty PS/2
device(s) or building a device that simulates the problem. If someone
were to send me a 'chatty' PS/2 module, I'd be willing to plug the stuff
back in and await the failure again. ReiserFS has done its job all
along, preventing corruption and (obvious) data loss.
I have a vague memory of some prior version of Linux not handling
'spurious' PS/2 interrupts. It is possible that 2.6.26 is also not
handling PS/2 problems as well as it should?
I'm posting this problem mostly as an FYI in the hope it will save
someone extended troubleshooting time. If it turns out to be a bonafide
bug, so much the better! I know no OS can completely prevent all
hardware problems from causing system failures; this may be one of those
exceptions.
Neal
-- Package-specific info:
** Version:
Linux version 2.6.26-1-686 (Debian 2.6.26-13) (waldi@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-24)) #1 SMP Sat Jan 10 18:29:31 UTC 2009
** Command line:
root=/dev/sda1 ro
** Not tainted
** Kernel log:
[ 26.363852] i2c-adapter i2c-2: unable to read EDID block.
[ 26.566151] i2c-adapter i2c-2: unable to read EDID block.
[ 26.756029] i2c-adapter i2c-3: unable to read EDID block.
[ 26.971986] i2c-adapter i2c-3: unable to read EDID block.
[ 27.140023] i2c-adapter i2c-3: unable to read EDID block.
[ 27.194517] nvidiafb: CRTC 0 is currently programmed for DFP
[ 27.194556] nvidiafb: Using DFP on CRTC 0
[ 27.194592] nvidiafb: Panel size is 1280 x 1024
[ 27.194628] nvidiafb: Panel is TMDS
[ 27.198181] nvidiafb: MTRR set to ON
[ 27.198239] fbcvt: 1280x1024@60: CVT Name - 1.310M4-R
[ 27.520572] nvidiafb: Flat panel dithering disabled
[ 27.520572] Console: switching to colour frame buffer device 160x64
[ 27.524032] nvidiafb: PCI nVidia NV39 framebuffer (64MB @ 0xD0000000)
[ 33.895951] md: md1 stopped.
[ 33.898892] md: bind<sdb1>
[ 33.898892] md: bind<sdc1>
[ 33.964042] md: raid0 personality registered for level 0
[ 33.964042] md1: setting max_sectors to 32, segment boundary to 8191
[ 33.964042] raid0: looking at sdc1
[ 33.964042] raid0: comparing sdc1(97667072) with sdc1(97667072)
[ 33.964042] raid0: END
[ 33.964042] raid0: ==> UNIQUE
[ 33.964042] raid0: 1 zones
[ 33.964042] raid0: looking at sdb1
[ 33.964042] raid0: comparing sdb1(97667072) with sdc1(97667072)
[ 33.964042] raid0: EQUAL
[ 33.964042] raid0: FINAL 1 zones
[ 33.964042] raid0: done.
[ 33.964042] raid0 : md_size is 195334144 blocks.
[ 33.964042] raid0 : conf->hash_spacing is 195334144 blocks.
[ 33.964042] raid0 : nb_zone is 1.
[ 33.964042] raid0 : Allocating 4 bytes for hash.
[ 33.964042] md: md2 stopped.
[ 33.969525] md: bind<sdb2>
[ 33.969583] md: bind<sdc2>
[ 34.049269] md2: setting max_sectors to 32, segment boundary to 8191
[ 34.049269] raid0: looking at sdc2
[ 34.049269] raid0: comparing sdc2(97667072) with sdc2(97667072)
[ 34.049269] raid0: END
[ 34.049269] raid0: ==> UNIQUE
[ 34.049269] raid0: 1 zones
[ 34.049269] raid0: looking at sdb2
[ 34.049269] raid0: comparing sdb2(97667072) with sdc2(97667072)
[ 34.049269] raid0: EQUAL
[ 34.049269] raid0: FINAL 1 zones
[ 34.049269] raid0: done.
[ 34.049269] raid0 : md_size is 195334144 blocks.
[ 34.049269] raid0 : conf->hash_spacing is 195334144 blocks.
[ 34.049269] raid0 : nb_zone is 1.
[ 34.049269] raid0 : Allocating 4 bytes for hash.
[ 34.519212] fuse init (API version 7.9)
[ 34.723686] kjournald starting. Commit interval 5 seconds
[ 34.723686] EXT3 FS on sda4, internal journal
[ 34.723686] EXT3-fs: mounted filesystem with ordered data mode.
[ 34.723686] ReiserFS: md1: found reiserfs format "3.6" with standard journal
[ 34.723686] ReiserFS: md1: using ordered data mode
[ 34.773741] ReiserFS: md1: journal params: device md1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 34.773741] ReiserFS: md1: checking transaction log (md1)
[ 34.801742] ReiserFS: md1: replayed 1 transactions in 0 seconds
[ 34.821741] ReiserFS: md1: Using r5 hash to sort names
[ 34.863343] ReiserFS: md2: found reiserfs format "3.6" with standard journal
[ 34.863343] ReiserFS: md2: using ordered data mode
[ 34.879151] ReiserFS: md2: journal params: device md2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 34.879151] ReiserFS: md2: checking transaction log (md2)
[ 34.879151] ReiserFS: md2: replayed 1 transactions in 0 seconds
[ 34.913742] ReiserFS: md2: Using r5 hash to sort names
[ 35.084310] kjournald starting. Commit interval 5 seconds
[ 35.084310] EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
[ 35.084310] EXT3 FS on sdc3, internal journal
[ 35.084310] EXT3-fs: mounted filesystem with ordered data mode.
[ 36.035092] NET: Registered protocol family 15
[ 38.257198] NET: Registered protocol family 10
[ 38.257551] lo: Disabled Privacy Extensions
[ 38.731818] Bridge firewalling registered
[ 38.731920] br0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
[ 38.864792] device eth0 entered promiscuous mode
[ 38.921329] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 40.508910] tg3: eth0: Link is up at 100 Mbps, half duplex.
[ 40.508910] tg3: eth0: Flow control is off for TX and off for RX.
[ 40.508910] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 40.508910] br0: port 1(eth0) entering learning state
[ 50.744987] br0: no IPv6 routers present
[ 53.194069] eth0: no IPv6 routers present
[ 57.840127] br0: topology change detected, propagating
[ 57.840177] br0: port 1(eth0) entering forwarding state
[ 71.078674] lp0: using parport0 (interrupt-driven).
[ 71.122676] ppdev: user-space parallel port driver
[ 76.383918] RPC: Registered udp transport module.
[ 76.383918] RPC: Registered tcp transport module.
[ 76.562079] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 76.686653] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 76.693315] NFSD: starting 90-second grace period
[ 85.173772] warning: `ntpd' uses 32-bit capabilities (legacy support in use)
[ 106.082458] eth0: no IPv6 routers present
[ 272.248864] ppdev0: registered pardevice
[ 272.248864] ppdev0: unregistered pardevice
[ 276.409999] ppdev0: registered pardevice
[ 276.457892] ppdev0: unregistered pardevice
[ 3258.034690] cdrom: This disc doesn't have any tracks I recognize!
** Loaded modules:
Module Size Used by
nfsd 186704 13
lockd 54248 1 nfsd
nfs_acl 2912 1 nfsd
auth_rpcgss 33952 1 nfsd
sunrpc 162144 11 nfsd,lockd,nfs_acl,auth_rpcgss
exportfs 3904 1 nfsd
battery 10180 0
ppdev 6468 0
lp 8164 0
bridge 40024 0
ipv6 235300 41
deflate 2624 0
zlib_deflate 17624 1 deflate
zlib_inflate 14144 1 deflate
ctr 3936 0
twofish 8224 0
twofish_common 13888 1 twofish
camellia 19136 0
serpent 18688 0
blowfish 8352 0
des_generic 16672 0
cbc 3264 0
aes_i586 7744 0
aes_generic 29256 1 aes_i586
xcbc 4296 0
sha256_generic 11360 0
sha1_generic 2304 0
crypto_null 2880 0
crypto_blkcipher 15236 3 ctr,cbc,crypto_null
af_key 25492 0
ext3 105512 2
jbd 39444 1 ext3
mbcache 7108 1 ext3
fuse 42908 1
raid0 6368 2
md_mod 67036 3 raid0
w83792d 22872 0
nvidiafb 39776 2
fb_ddc 2080 1 nvidiafb
i2c_algo_bit 5188 1 nvidiafb
vgastate 7680 1 nvidiafb
loop 12748 0
snd_cs4232 11380 0
snd_opl3_lib 9344 1 snd_cs4232
snd_hwdep 6212 1 snd_opl3_lib
snd_cs4231_lib 20512 1 snd_cs4232
snd_mpu401 6152 0
snd_intel8x0 26268 1
snd_mpu401_uart 6368 2 snd_cs4232,snd_mpu401
snd_ac97_codec 88484 1 snd_intel8x0
ac97_bus 1728 1 snd_ac97_codec
snd_pcm_oss 32800 0
snd_mixer_oss 12320 1 snd_pcm_oss
snd_pcm 62596 4 snd_cs4231_lib,snd_intel8x0,snd_ac97_codec,snd_pcm_oss
snd_seq_dummy 2660 0
snd_seq_oss 24992 0
snd_seq_midi 5728 0
snd_seq_midi_event 6432 2 snd_seq_oss,snd_seq_midi
snd_seq 41456 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_rawmidi 18496 2 snd_mpu401_uart,snd_seq_midi
parport_pc 22500 1
parport 30988 3 ppdev,lp,parport_pc
snd_timer 17800 4 snd_opl3_lib,snd_cs4231_lib,snd_pcm,snd_seq
ns558 3712 0
pcspkr 2432 0
snd_seq_device 6380 6 snd_opl3_lib,snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq,snd_rawmidi
k8temp 4064 0
gameport 10700 2 ns558
wacom 15776 0
snd 45604 18 snd_cs4232,snd_opl3_lib,snd_hwdep,snd_cs4231_lib,snd_mpu401,snd_intel8x0,snd_mpu401_uart,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_seq,snd_rawmidi,snd_timer,snd_seq_device
i2c_nforce2 5536 0
i2c_core 19828 5 w83792d,nvidiafb,fb_ddc,i2c_algo_bit,i2c_nforce2
button 6096 0
soundcore 6368 1 snd
snd_page_alloc 7816 3 snd_cs4231_lib,snd_intel8x0,snd_pcm
joydev 8480 0
evdev 8000 5
reiserfs 189920 3
dm_mirror 15104 0
dm_log 8452 1 dm_mirror
dm_snapshot 14340 0
dm_mod 46184 3 dm_mirror,dm_log,dm_snapshot
sg 26964 0
sr_mod 13316 0
sd_mod 22200 11
cdrom 30176 1 sr_mod
ide_pci_generic 3908 0 [permanent]
amd74xx 7752 0 [permanent]
ide_core 96168 2 ide_pci_generic,amd74xx
usbhid 35904 0
hid 33184 1 usbhid
ff_memless 4392 1 usbhid
floppy 47716 0
tg3 84708 0
ata_generic 4676 0
sata_nv 19208 8
libata 140384 2 ata_generic,sata_nv
scsi_mod 129356 4 sg,sr_mod,sd_mod,libata
dock 8304 1 libata
ehci_hcd 28428 0
ohci_hcd 18500 0
usbcore 118160 5 wacom,usbhid,ehci_hcd,ohci_hcd
thermal 15228 0
processor 32576 1 thermal
fan 4164 0
thermal_sys 10856 3 thermal,processor,fan
** PCI devices:
00:00.0 Memory controller [0580]: nVidia Corporation CK804 Memory Controller [10de:005e] (rev a3)
Subsystem: ASUSTeK Computer Inc. Device [1043:8162]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:01.0 ISA bridge [0601]: nVidia Corporation CK804 ISA Bridge [10de:0051] (rev a3)
Subsystem: ASUSTeK Computer Inc. Device [1043:8162]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:01.1 SMBus [0c05]: nVidia Corporation CK804 SMBus [10de:0052] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:8162]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at fc00 [size=32]
Region 4: I/O ports at 1d00 [size=64]
Region 5: I/O ports at 1e00 [size=64]
Capabilities: <access denied>
Kernel driver in use: nForce2_smbus
Kernel modules: i2c-nforce2
00:02.0 USB Controller [0c03]: nVidia Corporation CK804 USB Controller [10de:005a] (rev a2) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:8162]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 23
Region 0: Memory at fe02f000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:02.1 USB Controller [0c03]: nVidia Corporation CK804 USB Controller [10de:005b] (rev a3) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:8162]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 22
Region 0: Memory at feb00000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:04.0 Multimedia audio controller [0401]: nVidia Corporation CK804 AC'97 Audio Controller [10de:0059] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:8174]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin A routed to IRQ 23
Region 0: I/O ports at f000 [size=256]
Region 1: I/O ports at ec00 [size=256]
Region 2: Memory at fe02d000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: Intel ICH
Kernel modules: snd-intel8x0
00:06.0 IDE interface [0101]: nVidia Corporation CK804 IDE [10de:0053] (rev f2) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. Device [1043:8162]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1]
Region 4: I/O ports at e800 [size=16]
Capabilities: <access denied>
Kernel driver in use: AMD_IDE
Kernel modules: amd74xx
00:07.0 IDE interface [0101]: nVidia Corporation CK804 Serial ATA Controller [10de:0054] (rev f3) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. Device [1043:8162]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at 09f0 [size=8]
Region 1: I/O ports at 0bf0 [size=4]
Region 2: I/O ports at 0970 [size=8]
Region 3: I/O ports at 0b70 [size=4]
Region 4: I/O ports at d400 [size=16]
Region 5: Memory at fe02c000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: sata_nv
Kernel modules: sata_nv
00:08.0 IDE interface [0101]: nVidia Corporation CK804 Serial ATA Controller [10de:0055] (rev f3) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. Device [1043:8162]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at 09e0 [size=8]
Region 1: I/O ports at 0be0 [size=4]
Region 2: I/O ports at 0960 [size=8]
Region 3: I/O ports at 0b60 [size=4]
Region 4: I/O ports at c000 [size=16]
Region 5: Memory at fe02b000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: sata_nv
Kernel modules: sata_nv
00:09.0 PCI bridge [0604]: nVidia Corporation CK804 PCI Bridge [10de:005c] (rev a2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=128
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: fde00000-fdefffff
Prefetchable memory behind bridge: fdf00000-fdffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn-
00:0c.0 PCI bridge [0604]: nVidia Corporation CK804 PCIE Bridge [10de:005d] (rev a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00009000-00009fff
Memory behind bridge: fdd00000-fddfffff
Prefetchable memory behind bridge: 00000000fdc00000-00000000fdcfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:0d.0 PCI bridge [0604]: nVidia Corporation CK804 PCIE Bridge [10de:005d] (rev a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00008000-00008fff
Memory behind bridge: fdb00000-fdbfffff
Prefetchable memory behind bridge: 00000000fda00000-00000000fdafffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:0e.0 PCI bridge [0604]: nVidia Corporation CK804 PCIE Bridge [10de:005d] (rev a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 00007000-00007fff
Memory behind bridge: fa000000-fcffffff
Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map [1022:1101]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller [1022:1102]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control [1022:1103]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Kernel driver in use: k8temp
Kernel modules: k8temp
00:19.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:19.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map [1022:1101]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:19.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller [1022:1102]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:19.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control [1022:1103]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Kernel driver in use: k8temp
Kernel modules: k8temp
01:06.0 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 41) (prog-if 10 [OHCI])
Subsystem: Adaptec Device [9004:0035]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (250ns min, 10500ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fdeff000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
01:06.1 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 41) (prog-if 10 [OHCI])
Subsystem: Adaptec Device [9004:0035]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (250ns min, 10500ns max), Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 19
Region 0: Memory at fdefe000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
01:06.2 USB Controller [0c03]: NEC Corporation USB 2.0 [1033:00e0] (rev 02) (prog-if 20 [EHCI])
Subsystem: Adaptec Device [9004:00e0]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (4000ns min, 8500ns max), Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 16
Region 0: Memory at fdefd000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
02:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5751 Gigabit Ethernet PCI Express [14e4:1677] (rev 11)
Subsystem: ASUSTeK Computer Inc. Device [1043:814b]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fddf0000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at <ignored> [disabled]
Capabilities: <access denied>
Kernel driver in use: tg3
Kernel modules: tg3
04:00.0 VGA compatible controller [0300]: nVidia Corporation G70 [GeForce 7600 GS] [10de:0392] (rev a1) (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. Device [1043:81f5]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fa000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at fb000000 (64-bit, non-prefetchable) [size=16M]
Region 5: I/O ports at 7c00 [size=128]
[virtual] Expansion ROM at fc000000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: nvidiafb
Kernel modules: nvidiafb, nvidia
-- System Information:
Debian Release: 5.0
APT prefers oldstable
APT policy: (500, 'oldstable'), (500, 'stable')
Architecture: i386 (i686)
Kernel: Linux 2.6.26-1-686 (SMP w/4 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.26-1-686 depends on:
ii debconf [debconf-2.0] 1.5.24 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92o tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.26-1-686 recommends:
ii libc6-i686 2.7-18 GNU C Library: Shared libraries [i
Versions of packages linux-image-2.6.26-1-686 suggests:
ii grub 0.97-47lenny2 GRand Unified Bootloader (Legacy v
pn linux-doc-2.6.26 <none> (no description available)
-- debconf information:
linux-image-2.6.26-1-686/preinst/abort-overwrite-2.6.26-1-686:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.26-1-686/postinst/bootloader-error-2.6.26-1-686:
linux-image-2.6.26-1-686/postinst/depmod-error-initrd-2.6.26-1-686: false
linux-image-2.6.26-1-686/prerm/removing-running-kernel-2.6.26-1-686: true
linux-image-2.6.26-1-686/postinst/old-system-map-link-2.6.26-1-686: true
linux-image-2.6.26-1-686/preinst/abort-install-2.6.26-1-686:
linux-image-2.6.26-1-686/preinst/lilo-has-ramdisk:
linux-image-2.6.26-1-686/preinst/bootloader-initrd-2.6.26-1-686: true
linux-image-2.6.26-1-686/prerm/would-invalidate-boot-loader-2.6.26-1-686: true
linux-image-2.6.26-1-686/preinst/elilo-initrd-2.6.26-1-686: true
linux-image-2.6.26-1-686/postinst/kimage-is-a-directory:
linux-image-2.6.26-1-686/postinst/old-dir-initrd-link-2.6.26-1-686: true
linux-image-2.6.26-1-686/postinst/create-kimage-link-2.6.26-1-686: true
linux-image-2.6.26-1-686/preinst/lilo-initrd-2.6.26-1-686: true
linux-image-2.6.26-1-686/postinst/old-initrd-link-2.6.26-1-686: true
linux-image-2.6.26-1-686/preinst/overwriting-modules-2.6.26-1-686: true
linux-image-2.6.26-1-686/postinst/depmod-error-2.6.26-1-686: false
linux-image-2.6.26-1-686/postinst/bootloader-test-error-2.6.26-1-686:
linux-image-2.6.26-1-686/preinst/failed-to-move-modules-2.6.26-1-686:
linux-image-2.6.26-1-686/preinst/initrd-2.6.26-1-686:
Reply to: