Bug#511960: linux-image-2.6.26-1-amd64: The same here for a PATA DVD burner
Package: linux-image-2.6.26-1-amd64
Version: 2.6.26-13
Followup-For: Bug #511960
The same behavior visible on my new motherboard with ICH10 and JMicron PATA chip. A
HDD and DVD burner are connected to that PATA channel. HDD works ok (is jumpered
as SLAVE) and DVD (MASTER) reports this log. It starts later after startup, not
in the boot time.
After e.g. one hour, it starts reporting and the DBUS/HAL is being notified
which causes my Gnome to think I've inserted an audio CD into the drive.
I tried to use hdparm and set UDMA33 to the DVD drive but without any changein
this behavior. DVD was previously in a different machine (debian ia32, ICH5) and
without any problems.
In the case of this mulfunction, I'm unable to operate the drive, even eject
doesnt work. Only way is to reset the device with the hdparm command.
With an upgrade of system, it stopped to show the "DriveReady etc." messages but
it shows just the "drive not ready for command"
-- Package-specific info:
** Kernel log:
[15317.685410] hda: drive not ready for command
[15317.685446] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[15317.685454] ide: failed opcode was: unknown
[15317.685458] hda: drive not ready for command
[15317.685505] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[15317.685514] ide: failed opcode was: unknown
[15317.685518] hda: drive not ready for command
[15317.685560] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[15317.685565] ide: failed opcode was: unknown
[15317.685568] hda: drive not ready for command
[15319.770500] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[15319.770500] ide: failed opcode was: unknown
** Loaded modules:
Module Size Used by
i915 35072 2
drm 91488 3 i915
binfmt_misc 13580 1
ppdev 11656 0
lp 14724 0
ipv6 288328 22
acpi_cpufreq 11792 1
cpufreq_powersave 6400 0
cpufreq_conservative 11784 0
cpufreq_ondemand 11792 1
cpufreq_userspace 8452 0
cpufreq_stats 9120 0
freq_table 9344 3 acpi_cpufreq,cpufreq_ondemand,cpufreq_stats
nls_iso8859_2 9984 2
nls_cp852 10368 2
vfat 14976 2
fat 51128 1 vfat
nls_base 12932 4 nls_iso8859_2,nls_cp852,vfat,fat
coretemp 11008 0
w83627ehf 26512 0
hwmon_vid 7296 1 w83627ehf
loop 19468 0
tda1004x 19844 1
cx22700 10244 0
snd_usb_audio 91296 0
snd_usb_lib 20224 1 snd_usb_audio
snd_emu10k1_synth 10752 0
snd_emux_synth 36864 1 snd_emu10k1_synth
snd_seq_virmidi 10112 1 snd_emux_synth
snd_seq_midi_emul 10496 1 snd_emux_synth
snd_emu10k1 141536 3 snd_emu10k1_synth
parport_pc 31016 1
snd_ac97_codec 115416 1 snd_emu10k1
parport 41776 3 ppdev,lp,parport_pc
ac97_bus 6272 1 snd_ac97_codec
snd_pcm_oss 41760 0
snd_mixer_oss 18816 1 snd_pcm_oss
snd_pcm 81672 5 snd_usb_audio,snd_emu10k1,snd_ac97_codec,snd_pcm_oss
snd_page_alloc 13072 2 snd_emu10k1,snd_pcm
snd_util_mem 8960 2 snd_emux_synth,snd_emu10k1
snd_seq_dummy 7428 0
snd_seq_oss 33152 0
snd_hwdep 12040 3 snd_usb_audio,snd_emux_synth,snd_emu10k1
snd_seq_midi 11072 0
snd_rawmidi 26784 4 snd_usb_lib,snd_seq_virmidi,snd_emu10k1,snd_seq_midi
snd_seq_midi_event 11904 3 snd_seq_virmidi,snd_seq_oss,snd_seq_midi
snd_seq 54304 9 snd_emux_synth,snd_seq_virmidi,snd_seq_midi_emul,snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_timer 25744 3 snd_emu10k1,snd_pcm,snd_seq
snd_seq_device 11668 8 snd_emu10k1_synth,snd_emux_synth,snd_emu10k1,snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
i2c_i801 13596 0
emu10k1_gp 7552 0
snd 63688 17 snd_usb_audio,snd_emux_synth,snd_seq_virmidi,snd_emu10k1,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_hwdep,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
uvcvideo 55560 0
gameport 17040 2 emu10k1_gp
compat_ioctl32 12288 1 uvcvideo
videodev 35840 2 uvcvideo,compat_ioctl32
soundcore 12064 1 snd
dvb_ttusb_budget 22560 0
v4l1_compat 17284 2 uvcvideo,videodev
dvb_core 82740 1 dvb_ttusb_budget
firmware_class 12544 3 tda1004x,snd_emu10k1,dvb_ttusb_budget
i2c_core 27936 4 tda1004x,cx22700,i2c_i801,dvb_ttusb_budget
intel_agp 31728 1
button 11680 0
evdev 14208 4
ext3 125072 1
jbd 51240 1 ext3
mbcache 12804 1 ext3
ide_cd_mod 36360 0
cdrom 37928 1 ide_cd_mod
ide_disk 16512 3
ide_pci_generic 9220 0 [permanent]
usb_storage 94528 0
sd_mod 29376 3
jmicron 6912 0 [permanent]
ide_core 128284 4 ide_cd_mod,ide_disk,ide_pci_generic,jmicron
usbhid 45792 0
hid 41792 1 usbhid
ff_memless 9224 1 usbhid
ahci 33036 2
r8169 31492 0
ata_generic 10116 0
libata 165472 2 ahci,ata_generic
scsi_mod 160760 3 usb_storage,sd_mod,libata
dock 14112 1 libata
ehci_hcd 36108 0
uhci_hcd 25760 0
thermal 22688 0
processor 42304 2 acpi_cpufreq,thermal
fan 9352 0
thermal_sys 17728 3 thermal,processor,fan
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 4 Series Chipset DRAM Controller [8086:2e20] (rev 03)
Subsystem: ASUSTeK Computer Inc. Device [1043:8336]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
Kernel modules: intel-agp
00:02.0 VGA compatible controller [0300]: Intel Corporation 4 Series Chipset Integrated Graphics Controller [8086:2e22] (rev 03) (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. Device [1043:8336]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fe400000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at bc00 [size=8]
Capabilities: <access denied>
00:02.1 Display controller [0380]: Intel Corporation 4 Series Chipset Integrated Graphics Controller [8086:2e23] (rev 03)
Subsystem: ASUSTeK Computer Inc. Device [1043:8336]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at fe900000 (64-bit, non-prefetchable) [size=1M]
Capabilities: <access denied>
00:1a.0 USB Controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #4 [8086:3a37] (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:82d4]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at b480 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.1 USB Controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #5 [8086:3a38] (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:82d4]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at b800 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.2 USB Controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #6 [8086:3a39] (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:82d4]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at b880 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.7 USB Controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #2 [8086:3a3c] (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:82d4]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fe8fbc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1c.0 PCI bridge [0604]: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 1 [8086:3a40] (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Prefetchable memory behind bridge: 00000000fdf00000-00000000fdffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.4 PCI bridge [0604]: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 5 [8086:3a48] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: feb00000-febfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.5 PCI bridge [0604]: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 6 [8086:3a4a] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fea00000-feafffff
Prefetchable memory behind bridge: 00000000fde00000-00000000fdefffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1d.0 USB Controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #1 [8086:3a34] (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:82d4]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at b000 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #2 [8086:3a35] (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:82d4]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at b080 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #3 [8086:3a36] (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:82d4]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at b400 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #1 [8086:3a3a] (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:82d4]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at fe8fb800 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev 90) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
I/O behind bridge: 0000e000-0000efff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801JIB (ICH10) LPC Interface Controller [8086:3a18]
Subsystem: ASUSTeK Computer Inc. Device [1043:82d4]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.2 SATA controller [0106]: Intel Corporation 82801JI (ICH10 Family) SATA AHCI Controller [8086:3a22] (prog-if 01 [AHCI 1.0])
Subsystem: ASUSTeK Computer Inc. Device [1043:82d4]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 1276
Region 0: I/O ports at a880 [size=8]
Region 1: I/O ports at a800 [size=4]
Region 2: I/O ports at a480 [size=8]
Region 3: I/O ports at a400 [size=4]
Region 4: I/O ports at a080 [size=32]
Region 5: Memory at fe8fa800 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
Kernel modules: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 82801JI (ICH10 Family) SMBus Controller [8086:3a30]
Subsystem: ASUSTeK Computer Inc. Device [1043:82d4]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fe8fb400 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 0400 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801
01:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 02)
Subsystem: ASUSTeK Computer Inc. Device [1043:82c6]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 1275
Region 0: I/O ports at c800 [size=256]
Region 2: Memory at fdeff000 (64-bit, prefetchable) [size=4K]
Region 4: Memory at fdee0000 (64-bit, prefetchable) [size=64K]
Expansion ROM at feaf0000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: r8169
Kernel modules: r8169
02:00.0 IDE interface [0101]: JMicron Technologies, Inc. JMB368 IDE controller [197b:2368] (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. Device [1043:827e]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at dc00 [size=8]
Region 1: I/O ports at d880 [size=4]
Region 2: I/O ports at d800 [size=8]
Region 3: I/O ports at d480 [size=4]
Region 4: I/O ports at d400 [size=16]
Expansion ROM at febf0000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: JMicron IDE
Kernel modules: ata_generic, jmicron, ide-pci-generic
04:01.0 Multimedia audio controller [0401]: Creative Labs SB Live! EMU10k1 [1102:0002] (rev 07)
Subsystem: Creative Labs SBLive! 5.1 Model SB0100 [1102:8064]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at e880 [size=32]
Capabilities: <access denied>
Kernel driver in use: EMU10K1_Audigy
Kernel modules: snd-emu10k1
04:01.1 Input device controller [0980]: Creative Labs SB Live! Game Port [1102:7002] (rev 07)
Subsystem: Creative Labs Gameport Joystick [1102:0020]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Region 0: I/O ports at ec00 [size=8]
Capabilities: <access denied>
Kernel driver in use: Emu10k1_gameport
Kernel modules: emu10k1-gp
** Version:
Linux version 2.6.26-1-amd64 (Debian 2.6.26-13) (waldi@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-24)) #1 SMP Sat Jan 10 17:57:00 UTC 2009
** Command line:
root=/dev/sda2 ro quiet vga=0x35A
** Not tainted
-- System Information:
Debian Release: 5.0
APT prefers unstable
APT policy: (500, 'unstable'), (500, 'testing'), (1, 'experimental')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.26-1-amd64 (SMP w/2 CPU cores)
Locale: LANG=en_US, LC_CTYPE=cs_CZ.ISO-8859-2 (charmap=ISO-8859-2)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.26-1-amd64 depends on:
ii debconf [debconf-2.0] 1.5.24 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92o tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
linux-image-2.6.26-1-amd64 recommends no packages.
Versions of packages linux-image-2.6.26-1-amd64 suggests:
ii grub 0.97-47lenny2 GRand Unified Bootloader (Legacy v
pn linux-doc-2.6.26 <none> (no description available)
-- debconf information:
linux-image-2.6.26-1-amd64/postinst/create-kimage-link-2.6.26-1-amd64: true
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.26-1-amd64/postinst/kimage-is-a-directory:
linux-image-2.6.26-1-amd64/postinst/old-initrd-link-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/preinst/bootloader-initrd-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/preinst/initrd-2.6.26-1-amd64:
linux-image-2.6.26-1-amd64/postinst/old-system-map-link-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/postinst/depmod-error-initrd-2.6.26-1-amd64: false
linux-image-2.6.26-1-amd64/preinst/overwriting-modules-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/preinst/elilo-initrd-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/postinst/bootloader-error-2.6.26-1-amd64:
linux-image-2.6.26-1-amd64/preinst/abort-install-2.6.26-1-amd64:
linux-image-2.6.26-1-amd64/preinst/lilo-initrd-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/postinst/depmod-error-2.6.26-1-amd64: false
linux-image-2.6.26-1-amd64/prerm/removing-running-kernel-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/prerm/would-invalidate-boot-loader-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/postinst/bootloader-test-error-2.6.26-1-amd64:
linux-image-2.6.26-1-amd64/preinst/abort-overwrite-2.6.26-1-amd64:
linux-image-2.6.26-1-amd64/postinst/old-dir-initrd-link-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/preinst/lilo-has-ramdisk:
linux-image-2.6.26-1-amd64/preinst/failed-to-move-modules-2.6.26-1-amd64:
Reply to: