Bug#511892: 'BUG: unable to handle kernel NULL pointer dereference at [...]' message when unplugging usb apc ups
Package: linux-image-2.6.26-1-amd64
Version: 2.6.26-12
Severity: normal
when unplugging then replugging the usb cable from the apc ups into another usb connector, the kernel outputs the message copied below.
I'm not sure if this persists if i turn off apcupsd or with a non-smp kernel or with a 32-bit kernel, but i'll try the first two and report back.
-- Package-specific info:
** Version:
Linux version 2.6.26-1-amd64 (Debian 2.6.26-12) (waldi@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-24)) #1 SMP Mon Dec 15 17:25:36 UTC 2008
** Command line:
BOOT_IMAGE=/boot/vmlinuz-2.6.26-1-amd64 root=UUID=cb96ea5e-b88f-4c2a-be38-2b7635d68686 ro quiet
** Tainted: G D (128)
** Kernel log:
[253256.165686] parport_pc 00:07: assign io 0 0x378-0x37f
[253256.165686] parport_pc 00:07: assign io 1 0x778-0x77d
[253256.165686] parport_pc 00:07: assign irq 0 10
[253256.165686] parport_pc 00:07: assign dma 0 1
[253256.165686] parport_pc 00:07: current resources: after pnp_assign_resources
[253256.165686] parport_pc 00:07: irq 10 flags 0x40000401
[253256.165686] parport_pc 00:07: dma 1 flags 0x40000800
[253256.165686] parport_pc 00:07: io 0x378-0x37f flags 0x40000101
[253256.165686] parport_pc 00:07: io 0x778-0x77d flags 0x40000101
[253256.165686] parport_pc 00:07: current resources: pnp_start_dev
[253256.165686] parport_pc 00:07: irq 10 flags 0x40000401
[253256.165686] parport_pc 00:07: dma 1 flags 0x40000800
[253256.165686] parport_pc 00:07: io 0x378-0x37f flags 0x40000101
[253256.165686] parport_pc 00:07: io 0x778-0x77d flags 0x40000101
[253256.165686] parport_pc 00:07: set resources
[253256.165686] parport_pc 00:07: encode 4 resources
[253256.165686] parport_pc 00:07: encode irq 10 edge high exclusive (2-byte descriptor)
[253256.165686] parport_pc 00:07: encode dma 1 type 0x0 transfer 0x0 master 0
[253256.165686] parport_pc 00:07: encode io 0x378-0x37f decode 0x1
[253256.165686] parport_pc 00:07: encode io 0x778-0x77d decode 0x1
[253256.165686] parport_pc 00:07: activated
[253256.165686] parport_pc 00:07: reported by Plug and Play ACPI
[253256.165686] parport0: PC-style at 0x378 (0x778), irq 10 [PCSPP,TRISTATE]
[253256.257889] parport_pc 00:07: driver attached
[253256.276269] lp0: using parport0 (interrupt-driven).
[253256.292264] ppa: Version 2.07 (for Linux 2.4.x)
[253256.328628] Uniform Multi-Platform E-IDE driver
[253256.328628] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[253256.387792] Driver 'sr' needs updating - please use bus_type methods
[253256.395788] st: Version 20080224, fixed bufsize 32768, s/g segs 256
[253256.395788] Driver 'st' needs updating - please use bus_type methods
[253256.452893] BIOS EDD facility v0.16 2004-Jun-25, 6 devices found
[258867.055259] usb 6-2: USB disconnect, address 3
[258878.575797] usb 5-2: new low speed USB device using uhci_hcd and address 2
[258878.826834] usb 5-2: configuration #1 chosen from 1 choice
[258880.587055] hiddev96hidraw0: USB HID v1.10 Device [American Power Conversion Smart-UPS 3000 RM FW:666.6.I USB FW:7.3] on usb-0000:00:1d.0-2
[258880.587055] usb 5-2: New USB device found, idVendor=051d, idProduct=0002
[258880.587055] usb 5-2: New USB device strings: Mfr=3, Product=1, SerialNumber=2
[258880.587055] usb 5-2: Product: Smart-UPS 3000 RM FW:666.6.I USB FW:7.3
[258880.587055] usb 5-2: Manufacturer: American Power Conversion
[258880.587055] usb 5-2: SerialNumber: JS0723008642
[259416.774393] usb 5-2: USB disconnect, address 2
[259425.494190] usb 5-1: new low speed USB device using uhci_hcd and address 3
[259425.686674] usb 5-1: configuration #1 chosen from 1 choice
[259427.550935] hiddev96hidraw0: USB HID v1.10 Device [American Power Conversion Smart-UPS 3000 RM FW:666.6.I USB FW:7.3] on usb-0000:00:1d.0-1
[259427.550935] usb 5-1: New USB device found, idVendor=051d, idProduct=0002
[259427.550935] usb 5-1: New USB device strings: Mfr=3, Product=1, SerialNumber=2
[259427.550935] usb 5-1: Product: Smart-UPS 3000 RM FW:666.6.I USB FW:7.3
[259427.550935] usb 5-1: Manufacturer: American Power Conversion
[259427.550935] usb 5-1: SerialNumber: JS0723008642
[271148.011266] usb 5-1: USB disconnect, address 3
[271148.022345] BUG: unable to handle kernel NULL pointer dereference at 00000000000000e8
[271148.022392] IP: [<ffffffffa00f1d7f>] :usbhid:hiddev_ioctl+0x39/0x552
[271148.022427] PGD 6c7e0067 PUD 392a6067 PMD 0
[271148.022452] Oops: 0000 [1] SMP
[271148.022474] CPU 0
[271148.022498] Modules linked in: edd joydev st sr_mod ide_disk ide_cd_mod cdrom ide_core lp parport_pc parport sg binfmt_misc ipv6 ext3 jbd mbcache fuse loop snd_hda_intel snd_pcm_oss snd_mixer_oss snd_pcm snd_seq_dummy snd_seq_oss snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq snd_timer serio_raw tpm_infineon snd_seq_device pcspkr tpm psmouse tpm_bios snd iTCO_wdt soundcore snd_page_alloc video output wmi button intel_agp evdev xfs raid0 md_mod usbhid hid ff_memless floppy e100 mii uhci_hcd ehci_hcd e1000e sd_mod thermal processor fan thermal_sys sata_sil24 ata_piix libata scsi_mod dock [last unloaded: ppa]
[271148.022751] Pid: 16643, comm: apcupsd Not tainted 2.6.26-1-amd64 #1
[271148.022775] RIP: 0010:[<ffffffffa00f1d7f>] [<ffffffffa00f1d7f>] :usbhid:hiddev_ioctl+0x39/0x552
[271148.022828] RSP: 0018:ffff810042c59e38 EFLAGS: 00010246
[271148.022850] RAX: 0000000000000000 RBX: ffff81003849e000 RCX: 00007fff0584ca90
[271148.022888] RDX: 00000000fffffffb RSI: ffff81001833b000 RDI: ffff81004f9d06c0
[271148.022925] RBP: 00007fff0584ca90 R08: 00000000400c4807 R09: 0000000000000000
[271148.022963] R10: 00000000021eb010 R11: ffffffff802f2139 R12: 00000000400c4807
[271148.023000] R13: 00000000400c4807 R14: 0000000000000004 R15: 0000000000000000
[271148.023038] FS: 00007fc0fd8316e0(0000) GS:ffffffff8053c000(0000) knlGS:0000000000000000
[271148.023077] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[271148.023100] CR2: 00000000000000e8 CR3: 0000000010ef6000 CR4: 00000000000006e0
[271148.023138] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[271148.023175] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[271148.023213] Process apcupsd (pid: 16643, threadinfo ffff810042c58000, task ffff81007bf66ea0)
[271148.023218] Stack: ffff8100010143b8 ffffffff80248954 ffff810042c59eb8 00000000ffffffff
[271148.023218] 0000000000000286 ffffffff80248a18 0000000000000286 ffff810042c59eb8
[271148.023218] 0000000000000286 ffff810042c59eb8 0000000000000001 ffffffff80248a2d
[271148.023218] Call Trace:
[271148.023218] [<ffffffff80248954>] ? lock_hrtimer_base+0x1b/0x3c
[271148.023218] [<ffffffff80248a18>] ? hrtimer_try_to_cancel+0x67/0x70
[271148.023218] [<ffffffff80248a2d>] ? hrtimer_cancel+0xc/0x16
[271148.023218] [<ffffffff8042916b>] ? do_nanosleep+0x64/0x9c
[271148.023218] [<ffffffff80248bfc>] ? hrtimer_nanosleep+0x54/0xbd
[271148.023218] [<ffffffff802a6655>] ? vfs_ioctl+0x55/0x6b
[271148.023218] [<ffffffff802a68b3>] ? do_vfs_ioctl+0x248/0x261
[271148.023218] [<ffffffff80429148>] ? do_nanosleep+0x41/0x9c
[271148.023218] [<ffffffff802a691d>] ? sys_ioctl+0x51/0x70
[271148.023218] [<ffffffff8020beca>] ? system_call_after_swapgs+0x8a/0x8f
[271148.023218]
[271148.023218]
[271148.023218] Code: 53 48 81 ec 90 00 00 00 48 8b b6 98 00 00 00 48 8b be 18 06 00 00 48 8b 5f 20 83 3f 00 48 8b 83 80 18 00 00 4c 8b 8b b8 19 00 00 <48> 8b 88 e8 00 00 00 0f 84 fe 04 00 00 41 81 f8 01 48 04 80 0f
[271148.023218] RIP [<ffffffffa00f1d7f>] :usbhid:hiddev_ioctl+0x39/0x552
[271148.023218] RSP <ffff810042c59e38>
[271148.023218] CR2: 00000000000000e8
[271148.023218] ---[ end trace a0c222edcec58115 ]---
[271152.096327] usb 1-2: new low speed USB device using uhci_hcd and address 4
[271152.344888] usb 1-2: configuration #1 chosen from 1 choice
[271154.200864] hiddev96hidraw0: USB HID v1.10 Device [American Power Conversion Smart-UPS 3000 RM FW:666.6.I USB FW:7.3] on usb-0000:00:1a.0-2
[271154.200864] usb 1-2: New USB device found, idVendor=051d, idProduct=0002
[271154.200864] usb 1-2: New USB device strings: Mfr=3, Product=1, SerialNumber=2
[271154.200864] usb 1-2: Product: Smart-UPS 3000 RM FW:666.6.I USB FW:7.3
[271154.200864] usb 1-2: Manufacturer: American Power Conversion
[271154.200864] usb 1-2: SerialNumber: JS0723008642
** Loaded modules:
Module Size Used by
edd 13456 0
joydev 14848 0
st 39460 0
sr_mod 19652 0
ide_disk 16512 0
ide_cd_mod 36360 0
cdrom 37928 2 sr_mod,ide_cd_mod
ide_core 128284 2 ide_disk,ide_cd_mod
lp 14724 0
parport_pc 31016 1
parport 41776 2 lp,parport_pc
sg 36448 0
binfmt_misc 13580 1
ipv6 288328 32
ext3 125072 2
jbd 51240 1 ext3
mbcache 12804 1 ext3
fuse 53184 1
loop 19468 0
snd_hda_intel 434776 0
snd_pcm_oss 41760 0
snd_mixer_oss 18816 1 snd_pcm_oss
snd_pcm 81672 2 snd_hda_intel,snd_pcm_oss
snd_seq_dummy 7428 0
snd_seq_oss 33152 0
snd_seq_midi 11072 0
snd_rawmidi 26784 1 snd_seq_midi
snd_seq_midi_event 11904 2 snd_seq_oss,snd_seq_midi
snd_seq 54304 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_timer 25744 2 snd_pcm,snd_seq
serio_raw 9860 0
tpm_infineon 12860 0
snd_seq_device 11668 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
pcspkr 7040 0
tpm 19520 1 tpm_infineon
psmouse 42268 0
tpm_bios 10880 1 tpm
snd 63688 9 snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
iTCO_wdt 15696 0
soundcore 12064 1 snd
snd_page_alloc 13072 2 snd_hda_intel,snd_pcm
video 24212 0
output 7808 1 video
wmi 11712 0
button 11680 0
intel_agp 31728 1
evdev 14208 0
xfs 475432 4
raid0 10624 0
md_mod 80164 1 raid0
usbhid 45792 1
hid 41792 1 usbhid
ff_memless 9224 1 usbhid
floppy 61672 0
e100 37648 0
mii 9856 1 e100
uhci_hcd 25760 0
ehci_hcd 36108 0
e1000e 99748 0
sd_mod 29376 12
thermal 22688 0
processor 42304 3 thermal
fan 9352 0
thermal_sys 17728 4 video,thermal,processor,fan
sata_sil24 18180 2
ata_piix 22660 4
libata 165472 2 sata_sil24,ata_piix
scsi_mod 160760 5 st,sr_mod,sg,sd_mod,libata
dock 14112 1 libata
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82Q33 Express DRAM Controller [8086:29d0] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:281e]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
Kernel modules: intel-agp
00:02.0 VGA compatible controller [0300]: Intel Corporation 82Q33 Express Integrated Graphics Controller [8086:29d2] (rev 02) (prog-if 00 [VGA controller])
Subsystem: Hewlett-Packard Company Device [103c:281e]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 5
Region 0: Memory at f0300000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at 3240 [size=8]
Region 2: Memory at e0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at f0200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <access denied>
00:03.0 Communication controller [0780]: Intel Corporation 82Q33 Express MEI Controller [8086:29d4] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:281e]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 0
Interrupt: pin A routed to IRQ 5
Region 0: Memory at f03a5900 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
00:19.0 Ethernet controller [0200]: Intel Corporation 82566DM-2 Gigabit Network Connection [8086:10bd] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:281e]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 1277
Region 0: Memory at f0380000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at f03a4000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at 3100 [size=32]
Capabilities: <access denied>
Kernel driver in use: e1000e
Kernel modules: e1000e
00:1a.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 [8086:2937] (rev 02) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:281e]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 3120 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 [8086:2938] (rev 02) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:281e]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at 3140 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.2 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 [8086:2939] (rev 02) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:281e]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 22
Region 4: I/O ports at 3160 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 [8086:293c] (rev 02) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Device [103c:281e]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 22
Region 0: Memory at f03a5000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1b.0 Audio device [0403]: Intel Corporation 82801I (ICH9 Family) HD Audio Controller [8086:293e] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:281e]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at f03a0000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:1c.0 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 [8086:2940] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=20, subordinate=20, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.1 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 [8086:2942] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=30, subordinate=30, sec-latency=0
I/O behind bridge: 00001000-00001fff
Memory behind bridge: f0400000-f04fffff
Prefetchable memory behind bridge: 0000000080000000-00000000800fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1d.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 [8086:2934] (rev 02) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:281e]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 3180 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 [8086:2935] (rev 02) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:281e]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at 31a0 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 [8086:2936] (rev 02) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:281e]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 22
Region 4: I/O ports at 31c0 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 [8086:293a] (rev 02) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Device [103c:281e]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 0: Memory at f03a5400 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev 92) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=07, subordinate=07, sec-latency=32
I/O behind bridge: 00002000-00002fff
Memory behind bridge: f0000000-f01fffff
Prefetchable memory behind bridge: 0000000080100000-00000000801fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801IB (ICH9) LPC Interface Controller [8086:2918] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:281e]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel modules: iTCO_wdt
00:1f.2 IDE interface [0101]: Intel Corporation 82801IB (ICH9) 2 port SATA IDE Controller [8086:2921] (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Hewlett-Packard Company Device [103c:281e]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 18
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 3200 [size=16]
Region 5: I/O ports at 3210 [size=16]
Capabilities: <access denied>
Kernel driver in use: ata_piix
Kernel modules: ide-pci-generic, ata_generic, ata_piix
00:1f.5 IDE interface [0101]: Intel Corporation 82801I (ICH9 Family) 2 port SATA IDE Controller [8086:2926] (rev 02) (prog-if 85 [Master SecO PriO])
Subsystem: Hewlett-Packard Company Device [103c:281e]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 18
Region 0: I/O ports at 3258 [size=8]
Region 1: I/O ports at 3270 [size=4]
Region 2: I/O ports at 3260 [size=8]
Region 3: I/O ports at 3274 [size=4]
Region 4: I/O ports at 3220 [size=16]
Region 5: I/O ports at 3230 [size=16]
Capabilities: <access denied>
Kernel driver in use: ata_piix
Kernel modules: ide-pci-generic, ata_generic, ata_piix
07:04.0 Ethernet controller [0200]: Intel Corporation 82557/8/9/0/1 Ethernet Pro 100 [8086:1229] (rev 08)
Subsystem: Intel Corporation EtherExpress PRO/100+ Management Adapter with Alert On LAN* [8086:000e]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (2000ns min, 14000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 20
Region 0: Memory at f0100000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 2100 [size=64]
Region 2: Memory at f0000000 (32-bit, non-prefetchable) [size=1M]
[virtual] Expansion ROM at 80100000 [disabled] [size=1M]
Capabilities: <access denied>
Kernel driver in use: e100
Kernel modules: eepro100, e100
30:00.0 RAID bus controller [0104]: Silicon Image, Inc. SiI 3132 Serial ATA Raid II Controller [1095:3132] (rev 01)
Subsystem: Silicon Image, Inc. Device [1095:7132]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at f0404000 (64-bit, non-prefetchable) [size=128]
Region 2: Memory at f0400000 (64-bit, non-prefetchable) [size=16K]
Region 4: I/O ports at 1100 [size=128]
[virtual] Expansion ROM at 80000000 [disabled] [size=512K]
Capabilities: <access denied>
Kernel driver in use: sata_sil24
Kernel modules: sata_sil24
-- System Information:
Debian Release: 5.0
APT prefers testing
APT policy: (900, 'testing'), (800, 'unstable')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.26-1-amd64 (SMP w/2 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.26-1-amd64 depends on:
ii debconf [debconf-2.0] 1.5.24 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92n tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
linux-image-2.6.26-1-amd64 recommends no packages.
Versions of packages linux-image-2.6.26-1-amd64 suggests:
ii grub-pc [grub] 1.96+20080724-12 GRand Unified Bootloader, version
pn linux-doc-2.6.26 <none> (no description available)
-- debconf-show failed
root@colector:~# debconf-show linux-image-2.6.26-1-amd64
linux-image-2.6.26-1-amd64/postinst/create-kimage-link-2.6.26-1-amd64: true
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.26-1-amd64/postinst/kimage-is-a-directory:
linux-image-2.6.26-1-amd64/postinst/old-initrd-link-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/preinst/bootloader-initrd-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/preinst/initrd-2.6.26-1-amd64:
linux-image-2.6.26-1-amd64/postinst/old-system-map-link-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/postinst/depmod-error-initrd-2.6.26-1-amd64: false
linux-image-2.6.26-1-amd64/preinst/overwriting-modules-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/preinst/elilo-initrd-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/postinst/bootloader-error-2.6.26-1-amd64:
linux-image-2.6.26-1-amd64/preinst/abort-install-2.6.26-1-amd64:
linux-image-2.6.26-1-amd64/preinst/lilo-initrd-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/postinst/depmod-error-2.6.26-1-amd64: false
linux-image-2.6.26-1-amd64/prerm/removing-running-kernel-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/prerm/would-invalidate-boot-loader-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/postinst/bootloader-test-error-2.6.26-1-amd64:
linux-image-2.6.26-1-amd64/preinst/abort-overwrite-2.6.26-1-amd64:
linux-image-2.6.26-1-amd64/postinst/old-dir-initrd-link-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/preinst/lilo-has-ramdisk:
linux-image-2.6.26-1-amd64/preinst/failed-to-move-modules-2.6.26-1-amd64:
Reply to: