Bug#511062: linux-image-2.6.26-1-686: NFS client hang and packet flood after resume from suspend to ram
Package: linux-image-2.6.26-1-686
Version: 2.6.26-12
Severity: normal
Within four hours after a client system resumes from suspend to ram, access on
the client to the NFS filesystem hangs, access to all other filesystems
eventually hang once cache is filled, and a flood of packets is observed on the
NFS server being emitted by the NFS client.
Both the NFS server and NFS client are running linux-image-2.6.26-1-686
2.6.26-12, and are on the same network switch.
The symptom is cleared by typing "/etc/init.d/nfs-kernel-server restart" on the
NFS server system "dors". At that time, the client regains normal operation
and the flood ceases. The client has in dmesg:
[13969.896074] Restarting tasks ... done.
[24837.320033] nfs: server dors not responding, still trying
[25140.408048] nfs: server dors not responding, timed out
[25140.408048] nfs: server dors not responding, timed out
[25140.500429] nfs: server dors OK
A tcpdump of the packet flood shows 23783 packets over a period of 1.37
seconds. The packets consist of TCP SYN from the client to the server,
followed by a TCP RST from the server to the client. The same port numbers are
reused in each packet; source port rxe, destination port 2049. The tcpdump is
available if required for analysis, but the user data in the packets is
confidential.
The symptom does not occur unless the NFS client system is first suspended or
hibernated, using pm-suspend and pm-hibernate, and then resumed.
Possibly unrelated observation; the disk access LED of the system is normally
off unless the disk is being accessed, but after resume from suspend or
hibernate the LED stays on. The disk can still be accessed.
-- Package-specific info:
** Version:
Linux version 2.6.26-1-686 (Debian 2.6.26-12) (waldi@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-24)) #1 SMP Mon Dec 15 18:15:07 UTC 2008
** Command line:
root=UUID=ce95ab50-301b-418b-8546-07b4d6cdd419 ro quiet splash resume=/dev/hda2
** Not tainted
** Kernel log:
[ 5.516369] ACPI: PCI Interrupt 0000:02:08.0[A] -> GSI 20 (level, low) -> IRQ 20
[ 5.607348] e100: eth0: e100_probe: addr 0xfe200000, irq 20, MAC addr 00:08:02:1b:d4:99
[ 5.664866] hda: max request size: 128KiB
[ 5.668676] hda: 80063424 sectors (40992 MB) w/2048KiB Cache, CHS=65535/16/63
[ 5.668688] hda: cache flushes not supported
[ 5.668787] hda: hda1 hda2
[ 5.691559] hdc: ATAPI 48X DVD-ROM CD-R/RW drive, 2048kB Cache
[ 5.691574] Uniform CD-ROM driver Revision: 3.20
[ 6.007825] PM: Starting manual resume from disk
[ 6.078592] kjournald starting. Commit interval 5 seconds
[ 6.078592] EXT3-fs: mounted filesystem with ordered data mode.
[ 8.240986] udevd version 125 started
[ 9.795423] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 9.818454] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 9.834535] Linux agpgart interface v0.103
[ 9.856651] agpgart: Detected an Intel 845G Chipset.
[ 9.860738] agpgart: AGP aperture is 64M @ 0xf8000000
[ 9.870616] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
[ 9.870742] iTCO_wdt: Found a ICH2 TCO device (Version=1, TCOBASE=0xf860)
[ 9.870787] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 9.956340] intel_rng: Firmware space is locked read-only. If you can't or
[ 9.956346] intel_rng: don't want to disable this in firmware setup, and if
[ 9.956348] intel_rng: you are certain that your system has a functional
[ 9.956351] intel_rng: RNG, try using the 'no_fwh_detect' option.
[ 10.465563] input: Power Button (FF) as /class/input/input0
[ 10.476119] ACPI: Power Button (FF) [PWRF]
[ 10.476339] input: Power Button (CM) as /class/input/input1
[ 10.495886] ACPI: Power Button (CM) [PBTN]
[ 11.936524] input: PC Speaker as /class/input/input2
[ 12.559162] parport_pc 00:07: reported by Plug and Play ACPI
[ 12.559226] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[ 12.862052] ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 17
[ 12.862088] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[ 13.480018] intel8x0_measure_ac97_clock: measured 55977 usecs
[ 13.480026] intel8x0: clocking to 41152
[ 14.444923] Adding 480808k swap on /dev/hda2. Priority:-1 extents:1 across:480808k
[ 14.886743] EXT3 FS on hda1, internal journal
[ 16.536166] e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
[ 17.673395] RPC: Registered udp transport module.
[ 17.673403] RPC: Registered tcp transport module.
[ 18.776198] NET: Registered protocol family 10
[ 18.777056] lo: Disabled Privacy Extensions
[ 21.433030] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[ 21.433041] apm: overridden by ACPI.
[ 23.981529] warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use)
[13963.799564] PM: Syncing filesystems ... done.
[13963.805130] Freezing user space processes ... (elapsed 0.02 seconds) done.
[13963.834254] Freezing remaining freezable tasks ... (elapsed 0.00 seconds) done.
[13963.834323] Suspending console(s)
[13963.834561] ACPI: Cannot set device to a higher-powered state than parent
[13963.991726] ACPI: Cannot set device to a higher-powered state than parent
[13963.992203] ACPI handle has no context!
[13963.992361] serial 00:09: disabled
[13963.992479] serial 00:08: disabled
[13963.992595] parport_pc 00:07: disabled
[13963.993182] ACPI: PCI interrupt for device 0000:02:08.0 disabled
[13964.008256] ACPI: PCI interrupt for device 0000:00:1f.5 disabled
[13964.008324] ACPI: PCI interrupt for device 0000:00:1f.4 disabled
[13964.008362] ACPI: PCI interrupt for device 0000:00:1f.2 disabled
[13964.008721] ACPI: Preparing to enter system sleep state S3
[13964.009210] Disabling non-boot CPUs ...
[13964.009210] Intel machine check architecture supported.
[13964.009226] Intel machine check reporting enabled on CPU#0.
[13964.009231] CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
[13964.009237] CPU0: Thermal monitoring enabled
[13964.009290] Back to C!
[13964.009850] PM: Writing back config space on device 0000:00:00.0 at offset 4 (was f0000008, writing f8000008)
[13964.009919] PM: Writing back config space on device 0000:00:1e.0 at offset 7 (was 22801010, writing 2801010)
[13964.009945] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[13964.010017] ACPI: PCI Interrupt 0000:00:1f.2[D] -> GSI 19 (level, low) -> IRQ 19
[13964.010027] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[13964.010078] usb usb1: root hub lost power or was reset
[13964.010100] ACPI: PCI Interrupt 0000:00:1f.4[C] -> GSI 23 (level, low) -> IRQ 23
[13964.010109] PCI: Setting latency timer of device 0000:00:1f.4 to 64
[13964.010157] usb usb2: root hub lost power or was reset
[13964.010178] PM: Writing back config space on device 0000:00:1f.5 at offset f (was 200, writing 20b)
[13964.010199] PM: Writing back config space on device 0000:00:1f.5 at offset 5 (was fc41, writing 2401)
[13964.010206] PM: Writing back config space on device 0000:00:1f.5 at offset 4 (was fe01, writing 2001)
[13964.010216] PM: Writing back config space on device 0000:00:1f.5 at offset 1 (was 2800005, writing 2800001)
[13964.010228] ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 17
[13964.010237] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[13964.328022] PM: Writing back config space on device 0000:02:08.0 at offset f (was 38080100, writing 38080105)
[13964.328042] PM: Writing back config space on device 0000:02:08.0 at offset 5 (was 1, writing 1001)
[13964.328049] PM: Writing back config space on device 0000:02:08.0 at offset 4 (was 0, writing fe200000)
[13964.328056] PM: Writing back config space on device 0000:02:08.0 at offset 3 (was 0, writing 4208)
[13964.328064] PM: Writing back config space on device 0000:02:08.0 at offset 1 (was 2900000, writing 2900107)
[13964.346077] parport_pc 00:07: activated
[13964.346704] serial 00:08: activated
[13964.347323] serial 00:09: activated
[13964.348136] e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
[13969.415107] hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
[13969.415458] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[13969.480380] hda: UDMA/100 mode selected
[13969.608516] hdc: host max PIO4 wanted PIO255(auto-tune) selected PIO4
[13969.608516] hdc: UDMA/44 mode selected
[13969.896074] Restarting tasks ... done.
[24837.320033] nfs: server dors not responding, still trying
[25140.408048] nfs: server dors not responding, timed out
[25140.408048] nfs: server dors not responding, timed out
[25140.500429] nfs: server dors OK
** Loaded modules:
Module Size Used by
ipv6 235300 16
nfs 213896 3
lockd 54248 1 nfs
nfs_acl 2912 1 nfs
sunrpc 162144 19 nfs,lockd,nfs_acl
evdev 8000 2
snd_intel8x0 26268 1
snd_ac97_codec 88484 1 snd_intel8x0
ac97_bus 1728 1 snd_ac97_codec
snd_pcm_oss 32800 1
snd_mixer_oss 12320 1 snd_pcm_oss
snd_pcm 62596 3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss
parport_pc 22500 0
parport 30988 1 parport_pc
snd_seq_dummy 2660 0
serio_raw 4740 0
psmouse 32336 0
pcspkr 2432 0
snd_seq_oss 24992 0
snd_seq_midi 5728 0
snd_rawmidi 18496 1 snd_seq_midi
snd_seq_midi_event 6432 2 snd_seq_oss,snd_seq_midi
snd_seq 41456 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
button 6096 0
snd_timer 17800 2 snd_pcm,snd_seq
snd_seq_device 6380 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
snd 45604 10 snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
soundcore 6368 2 snd
snd_page_alloc 7816 2 snd_intel8x0,snd_pcm
rng_core 3940 0
iTCO_wdt 9508 0
intel_agp 22332 1
agpgart 28776 1 intel_agp
shpchp 25528 0
pci_hotplug 23460 1 shpchp
ext3 105512 1
jbd 39444 1 ext3
mbcache 7108 1 ext3
ide_cd_mod 27652 0
cdrom 30176 1 ide_cd_mod
ide_disk 10496 3
ata_generic 4676 0
libata 140384 1 ata_generic
dock 8304 1 libata
floppy 47716 0
uhci_hcd 18672 0
usbcore 118160 2 uhci_hcd
e100 28908 0
mii 4896 1 e100
piix 6568 0 [permanent]
ide_pci_generic 3908 0 [permanent]
ide_core 96168 4 ide_cd_mod,ide_disk,piix,ide_pci_generic
thermal 15228 0
processor 32576 1 thermal
fan 4164 0
thermal_sys 10856 3 thermal,processor,fan
sym53c8xx 62904 0
scsi_transport_spi 19840 1 sym53c8xx
scsi_mod 129356 3 libata,sym53c8xx,scsi_transport_spi
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82845 845 [Brookdale] Chipset Host Bridge [8086:1a30] (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [e4] Vendor Specific Information <?>
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
Kernel driver in use: agpgart-intel
Kernel modules: intel-agp
00:01.0 PCI bridge [0604]: Intel Corporation 82845 845 [Brookdale] Chipset AGP Bridge [8086:1a31] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
Memory behind bridge: f7000000-f7ffffff
Prefetchable memory behind bridge: fc000000-fdffffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Kernel modules: shpchp
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev 12) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
I/O behind bridge: 00001000-00001fff
Memory behind bridge: fe000000-fe2fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Kernel modules: shpchp
00:1f.0 ISA bridge [0601]: Intel Corporation 82801BA ISA Bridge (LPC) [8086:2440] (rev 12)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Kernel modules: intel-rng, iTCO_wdt
00:1f.1 IDE interface [0101]: Intel Corporation 82801BA IDE U100 Controller [8086:244b] (rev 12) (prog-if 80 [Master])
Subsystem: Compaq Computer Corporation Device [0e11:2411]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1]
Region 4: I/O ports at 2480 [size=16]
Kernel driver in use: PIIX_IDE
Kernel modules: piix
00:1f.2 USB Controller [0c03]: Intel Corporation 82801BA/BAM USB Controller #1 [8086:2442] (rev 12) (prog-if 00 [UHCI])
Subsystem: Compaq Computer Corporation Device [0e11:2411]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 19
Region 4: I/O ports at 2440 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1f.4 USB Controller [0c03]: Intel Corporation 82801BA/BAM USB Controller #1 [8086:2444] (rev 12) (prog-if 00 [UHCI])
Subsystem: Compaq Computer Corporation Device [0e11:2411]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 23
Region 4: I/O ports at 2460 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1f.5 Multimedia audio controller [0401]: Intel Corporation 82801BA/BAM AC'97 Audio Controller [8086:2445] (rev 12)
Subsystem: Compaq Computer Corporation Evo D500 [0e11:0088]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at 2000 [size=256]
Region 1: I/O ports at 2400 [size=64]
Kernel driver in use: Intel ICH
Kernel modules: snd-intel8x0
01:00.0 VGA compatible controller [0300]: nVidia Corporation NV6 [Vanta/Vanta LT] [10de:002c] (rev 15) (prog-if 00 [VGA controller])
Subsystem: nVidia Corporation Device [10de:0072]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f7000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at fc000000 (32-bit, prefetchable) [size=32M]
Capabilities: [60] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
Kernel modules: nvidiafb
02:08.0 Ethernet controller [0200]: Intel Corporation 82801BA/BAM/CA/CAM Ethernet Controller [8086:2449] (rev 03)
Subsystem: Compaq Computer Corporation EtherExpress PRO/100 VM [0e11:0012]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 66 (2000ns min, 14000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 20
Region 0: Memory at fe200000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 1000 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: e100
Kernel modules: e100, eepro100
-- System Information:
Debian Release: 5.0
APT prefers testing
APT policy: (500, 'testing')
Architecture: i386 (i686)
Kernel: Linux 2.6.26-1-686 (SMP w/1 CPU core)
Locale: LANG=C, LC_CTYPE=C (charmap=ANSI_X3.4-1968)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.26-1-686 depends on:
ii debconf [debconf-2.0] 1.5.24 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92n tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.26-1-686 recommends:
ii libc6-i686 2.7-16 GNU C Library: Shared libraries [i
Versions of packages linux-image-2.6.26-1-686 suggests:
ii grub 0.97-47lenny1 GRand Unified Bootloader (Legacy v
pn linux-doc-2.6.26 <none> (no description available)
-- debconf information:
linux-image-2.6.26-1-686/preinst/abort-overwrite-2.6.26-1-686:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.26-1-686/postinst/bootloader-error-2.6.26-1-686:
linux-image-2.6.26-1-686/postinst/depmod-error-initrd-2.6.26-1-686: false
linux-image-2.6.26-1-686/prerm/removing-running-kernel-2.6.26-1-686: true
linux-image-2.6.26-1-686/postinst/old-system-map-link-2.6.26-1-686: true
linux-image-2.6.26-1-686/preinst/abort-install-2.6.26-1-686:
linux-image-2.6.26-1-686/preinst/lilo-has-ramdisk:
linux-image-2.6.26-1-686/preinst/bootloader-initrd-2.6.26-1-686: true
linux-image-2.6.26-1-686/prerm/would-invalidate-boot-loader-2.6.26-1-686: true
linux-image-2.6.26-1-686/preinst/elilo-initrd-2.6.26-1-686: true
linux-image-2.6.26-1-686/postinst/kimage-is-a-directory:
linux-image-2.6.26-1-686/postinst/old-dir-initrd-link-2.6.26-1-686: true
linux-image-2.6.26-1-686/postinst/create-kimage-link-2.6.26-1-686: true
linux-image-2.6.26-1-686/preinst/lilo-initrd-2.6.26-1-686: true
linux-image-2.6.26-1-686/postinst/old-initrd-link-2.6.26-1-686: true
linux-image-2.6.26-1-686/preinst/overwriting-modules-2.6.26-1-686: true
linux-image-2.6.26-1-686/postinst/depmod-error-2.6.26-1-686: false
linux-image-2.6.26-1-686/postinst/bootloader-test-error-2.6.26-1-686:
linux-image-2.6.26-1-686/preinst/failed-to-move-modules-2.6.26-1-686:
linux-image-2.6.26-1-686/preinst/initrd-2.6.26-1-686:
Reply to: