Bug#507728: linux-image-2.6.26-1-686: USB mass storage devices unreliable when connected through USB hubs
Package: linux-image-2.6.26-1-686
Version: 2.6.26-10
Severity: important
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
USB mass storage devices always seem to fail after a few moments of reading or
writing when they are connected via a USB hub. This is accompanied by messages
such as the following:
Dec 3 22:56:32 xerces kernel: [ 3975.148272] sd 6:0:0:0: [sda] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
Dec 3 22:56:32 xerces kernel: [ 3975.148286] end_request: I/O error, dev sda, sector 8065
Dec 3 22:56:32 xerces kernel: [ 3975.148303] Buffer I/O error on device sda1, logical block 1
Dec 3 22:56:32 xerces kernel: [ 3975.148307] lost page write due to I/O error on sda1
Dec 3 22:56:32 xerces kernel: [ 3975.148625] usb 4-3.1: USB disconnect, address 10
Dec 3 22:56:32 xerces kernel: [ 3975.151790] Buffer I/O error on device sda1, logical block 8192
Dec 3 22:56:32 xerces kernel: [ 3975.151800] lost page write due to I/O error on sda1
Dec 3 22:56:32 xerces hald[3015]: forcibly attempting to lazy unmount /dev/sda1 as enclosing drive was disconnected
Dec 3 22:56:32 xerces hald: unmounted /dev/sda1 from '/media/UDISK 2.0' on behalf of uid 0
This happens with two computers (a Samsung Q45 and a PC with an Asus A7V8X-X
motherboard); two mass storage devices (an Xclef HD-500 40 GB MP3 player, and a
play.com 16 GB flash device) and two hubs (a Belin F5U234 and a Trust
HU-5870V).
In all cases, connecting the device directly to the computer without going
through a hub eliminates the problem.
If the device disconnects while I am copying files to it then this causes DATA
LOSS as the original files are removed (this is probably a separate bug that I
should file against nautilus though).
- -- Package-specific info:
** Version:
Linux version 2.6.26-1-686 (Debian 2.6.26-10) (waldi@debian.org) (gcc version 4.1.3 20080623 (prerelease) (Debian 4.1.2-23)) #1 SMP Sat Nov 8 19:00:26 UTC 2008
** Command line:
BOOT_IMAGE=/boot/vmlinuz-2.6.26-1-686 root=/dev/md0 ro noresume vga=0x305 quiet
** Tainted: P (1)
** Kernel log:
[ 3850.488294] usb-storage: device scan complete
[ 3850.534969] scsi 3:0:0:0: Direct-Access USB DISK 2.0 PMAP PQ: 0 ANSI: 0 CCS
[ 3852.308778] sd 3:0:0:0: [sda] READ CAPACITY failed
[ 3852.308788] sd 3:0:0:0: [sda] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[ 3852.308802] sd 3:0:0:0: [sda] Sense not available.
[ 3852.308855] sd 3:0:0:0: [sda] Write Protect is off
[ 3852.308859] sd 3:0:0:0: [sda] Mode Sense: 00 00 00 00
[ 3852.308863] sd 3:0:0:0: [sda] Assuming drive cache: write through
[ 3852.309028] sd 3:0:0:0: [sda] Attached SCSI removable disk
[ 3852.312940] usb 4-3.3: USB disconnect, address 7
[ 3857.916177] usb 4-3.4: new high speed USB device using ehci_hcd and address 8
[ 3858.010800] usb 4-3.4: configuration #1 chosen from 1 choice
[ 3858.011161] scsi4 : SCSI emulation for USB Mass Storage devices
[ 3858.011439] usb 4-3.4: New USB device found, idVendor=13fe, idProduct=3100
[ 3858.011443] usb 4-3.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3858.011446] usb 4-3.4: Product: USB DISK 2.0
[ 3858.011448] usb 4-3.4: Manufacturer:
[ 3858.011450] usb 4-3.4: SerialNumber: 078A15502BA2
[ 3858.011459] usb-storage: device found at 8
[ 3858.011462] usb-storage: waiting for device to settle before scanning
[ 3863.008256] usb-storage: device scan complete
[ 3863.055296] scsi 4:0:0:0: Direct-Access USB DISK 2.0 PMAP PQ: 0 ANSI: 0 CCS
[ 3864.968454] sd 4:0:0:0: [sda] 31764480 512-byte hardware sectors (16263 MB)
[ 3864.968454] sd 4:0:0:0: [sda] Write Protect is off
[ 3864.968454] sd 4:0:0:0: [sda] Mode Sense: 23 00 00 00
[ 3864.968454] sd 4:0:0:0: [sda] Assuming drive cache: write through
[ 3864.975464] sd 4:0:0:0: [sda] 31764480 512-byte hardware sectors (16263 MB)
[ 3864.976069] sd 4:0:0:0: [sda] Write Protect is off
[ 3864.976069] sd 4:0:0:0: [sda] Mode Sense: 23 00 00 00
[ 3864.976069] sd 4:0:0:0: [sda] Assuming drive cache: write through
[ 3864.976069] sda: sda1
[ 3865.017854] sd 4:0:0:0: [sda] Attached SCSI removable disk
[ 3866.805509] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 3900.160786] sd 4:0:0:0: [sda] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[ 3900.160800] end_request: I/O error, dev sda, sector 8065
[ 3900.160809] Buffer I/O error on device sda1, logical block 1
[ 3900.160813] lost page write due to I/O error on sda1
[ 3900.161555] usb 4-3.4: USB disconnect, address 8
[ 3900.444209] usb 4-3.4: new high speed USB device using ehci_hcd and address 9
[ 3900.538822] usb 4-3.4: configuration #1 chosen from 1 choice
[ 3900.539276] scsi5 : SCSI emulation for USB Mass Storage devices
[ 3900.546478] usb 4-3.4: New USB device found, idVendor=13fe, idProduct=3100
[ 3900.546488] usb 4-3.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3900.546491] usb 4-3.4: Product: USB DISK 2.0
[ 3900.546494] usb 4-3.4: Manufacturer:
[ 3900.546496] usb 4-3.4: SerialNumber: 078A15502BA2
[ 3900.547079] usb-storage: device found at 9
[ 3900.547084] usb-storage: waiting for device to settle before scanning
[ 3904.726388] usb 4-3.4: USB disconnect, address 9
[ 3931.816167] usb 4-3.1: new high speed USB device using ehci_hcd and address 10
[ 3931.910665] usb 4-3.1: configuration #1 chosen from 1 choice
[ 3931.911591] scsi6 : SCSI emulation for USB Mass Storage devices
[ 3931.911874] usb 4-3.1: New USB device found, idVendor=13fe, idProduct=3100
[ 3931.911878] usb 4-3.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3931.911882] usb 4-3.1: Product: USB DISK 2.0
[ 3931.911884] usb 4-3.1: Manufacturer:
[ 3931.911886] usb 4-3.1: SerialNumber: 078A15502BA2
[ 3931.911902] usb-storage: device found at 10
[ 3931.911905] usb-storage: waiting for device to settle before scanning
[ 3936.908247] usb-storage: device scan complete
[ 3936.954888] scsi 6:0:0:0: Direct-Access USB DISK 2.0 PMAP PQ: 0 ANSI: 0 CCS
[ 3938.860641] sd 6:0:0:0: [sda] 31764480 512-byte hardware sectors (16263 MB)
[ 3938.861253] sd 6:0:0:0: [sda] Write Protect is off
[ 3938.861260] sd 6:0:0:0: [sda] Mode Sense: 23 00 00 00
[ 3938.861263] sd 6:0:0:0: [sda] Assuming drive cache: write through
[ 3938.866124] sd 6:0:0:0: [sda] 31764480 512-byte hardware sectors (16263 MB)
[ 3938.866746] sd 6:0:0:0: [sda] Write Protect is off
[ 3938.866752] sd 6:0:0:0: [sda] Mode Sense: 23 00 00 00
[ 3938.866755] sd 6:0:0:0: [sda] Assuming drive cache: write through
[ 3938.866762] sda: sda1
[ 3938.908298] sd 6:0:0:0: [sda] Attached SCSI removable disk
[ 3940.807930] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 3975.148272] sd 6:0:0:0: [sda] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[ 3975.148286] end_request: I/O error, dev sda, sector 8065
[ 3975.148303] Buffer I/O error on device sda1, logical block 1
[ 3975.148307] lost page write due to I/O error on sda1
[ 3975.148625] usb 4-3.1: USB disconnect, address 10
[ 3975.151790] Buffer I/O error on device sda1, logical block 8192
[ 3975.151800] lost page write due to I/O error on sda1
[ 3975.404111] usb 4-3.1: new high speed USB device using ehci_hcd and address 11
[ 3975.502719] usb 4-3.1: configuration #1 chosen from 1 choice
[ 3975.503193] scsi7 : SCSI emulation for USB Mass Storage devices
[ 3975.503433] usb 4-3.1: New USB device found, idVendor=13fe, idProduct=3100
[ 3975.503437] usb 4-3.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3975.503441] usb 4-3.1: Product: USB DISK 2.0
[ 3975.503443] usb 4-3.1: Manufacturer:
[ 3975.503445] usb 4-3.1: SerialNumber: 078A15502BA2
[ 3975.503455] usb-storage: device found at 11
[ 3975.503458] usb-storage: waiting for device to settle before scanning
[ 3977.120174] FAT: unable to read inode block for updating (i_pos 131081)
[ 3980.500276] usb-storage: device scan complete
[ 3980.547151] scsi 7:0:0:0: Direct-Access USB DISK 2.0 PMAP PQ: 0 ANSI: 0 CCS
[ 3980.908801] sd 7:0:0:0: [sda] READ CAPACITY failed
[ 3980.908811] sd 7:0:0:0: [sda] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
[ 3980.908817] sd 7:0:0:0: [sda] Sense not available.
[ 3980.908869] sd 7:0:0:0: [sda] Write Protect is off
[ 3980.908873] sd 7:0:0:0: [sda] Mode Sense: 00 00 00 00
[ 3980.908877] sd 7:0:0:0: [sda] Assuming drive cache: write through
[ 3980.909040] sd 7:0:0:0: [sda] Attached SCSI removable disk
[ 3980.910248] usb 4-3.1: USB disconnect, address 11
** Loaded modules:
Module Size Used by
nls_utf8 1760 0
nls_cp437 5568 0
vfat 9152 0
fat 40864 1 vfat
nls_base 6820 4 nls_utf8,nls_cp437,vfat,fat
sd_mod 22200 0
usb_storage 75936 0
nvidia 7086148 24
binfmt_misc 7528 1
ppdev 6468 0
lp 8164 0
ipv6 235300 32
cpufreq_conservative 5960 0
cpufreq_ondemand 6476 0
cpufreq_stats 3776 0
freq_table 4224 2 cpufreq_ondemand,cpufreq_stats
cpufreq_userspace 3172 0
cpufreq_powersave 1856 0
fuse 42908 3
aes_i586 7744 2
aes_generic 29256 1 aes_i586
cbc 3264 2
dm_crypt 11172 1
dm_mod 46184 5 dm_crypt
it87 17904 0
hwmon_vid 2720 1 it87
snd_emu10k1_synth 5664 0
snd_emux_synth 27936 1 snd_emu10k1_synth
snd_seq_virmidi 4896 1 snd_emux_synth
snd_seq_midi_emul 5376 1 snd_emux_synth
via_ircc 15732 0
irda 95480 1 via_ircc
crc_ccitt 2080 1 irda
arc4 1824 2
ecb 2624 2
crypto_blkcipher 15236 5 cbc,dm_crypt,ecb
parport_pc 22500 1
parport 30988 3 ppdev,lp,parport_pc
snd_emu10k1 115200 3 snd_emu10k1_synth
snd_seq_midi 5728 0
psmouse 32336 0
pcspkr 2432 0
snd_rawmidi 18496 3 snd_seq_virmidi,snd_emu10k1,snd_seq_midi
snd_ac97_codec 88484 1 snd_emu10k1
serio_raw 4740 0
ac97_bus 1728 1 snd_ac97_codec
snd_util_mem 4032 2 snd_emux_synth,snd_emu10k1
snd_hwdep 6212 2 snd_emux_synth,snd_emu10k1
snd_pcm_oss 32800 0
snd_pcm 62596 4 snd_emu10k1,snd_ac97_codec,snd_pcm_oss
snd_page_alloc 7816 2 snd_emu10k1,snd_pcm
i2c_viapro 6836 0
snd_mixer_oss 12320 1 snd_pcm_oss
i2c_core 19828 2 nvidia,i2c_viapro
snd_seq_dummy 2660 0
snd_seq_oss 24992 0
snd_seq_midi_event 6432 3 snd_seq_virmidi,snd_seq_midi,snd_seq_oss
snd_seq 41456 9 snd_emux_synth,snd_seq_virmidi,snd_seq_midi_emul,snd_seq_midi,snd_seq_dummy,snd_seq_oss,snd_seq_midi_event
snd_timer 17800 3 snd_emu10k1,snd_pcm,snd_seq
snd_seq_device 6380 8 snd_emu10k1_synth,snd_emux_synth,snd_emu10k1,snd_seq_midi,snd_rawmidi,snd_seq_dummy,snd_seq_oss,snd_seq
p54pci 8864 0
p54common 9888 1 p54pci
snd 45604 16 snd_emux_synth,snd_seq_virmidi,snd_emu10k1,snd_rawmidi,snd_ac97_codec,snd_hwdep,snd_pcm_oss,snd_pcm,snd_mixer_oss,snd_seq_oss,snd_seq,snd_timer,snd_seq_device
firmware_class 6816 2 snd_emu10k1,p54pci
button 6064 0
mac80211 139680 2 p54pci,p54common
cfg80211 21576 1 mac80211
soundcore 6368 1 snd
emu10k1_gp 2688 0
gameport 10700 2 emu10k1_gp
shpchp 25528 0
pci_hotplug 23460 1 shpchp
via_agp 7744 1
agpgart 28776 2 nvidia,via_agp
evdev 8000 3
ext3 105416 1
jbd 39444 1 ext3
mbcache 7108 1 ext3
raid1 18016 1
md_mod 67036 2 raid1
ide_cd_mod 27652 0
cdrom 30176 1 ide_cd_mod
ata_generic 4676 0
libata 140384 1 ata_generic
scsi_mod 129356 3 sd_mod,usb_storage,libata
dock 8272 1 libata
usbhid 35904 0
hid 33184 1 usbhid
ff_memless 4392 1 usbhid
via82cxxx 6948 0 [permanent]
ide_disk 10496 6
via_rhine 18664 0
mii 4896 1 via_rhine
ide_pci_generic 3908 0 [permanent]
ehci_hcd 28428 0
uhci_hcd 18672 0
usbcore 118160 5 usb_storage,usbhid,ehci_hcd,uhci_hcd
pdc202xx_new 5216 0 [permanent]
ide_core 96168 5 ide_cd_mod,via82cxxx,ide_disk,ide_pci_generic,pdc202xx_new
thermal 15228 0
processor 32576 1 thermal
fan 4164 0
thermal_sys 10856 3 thermal,processor,fan
** PCI devices:
00:00.0 Host bridge [0600]: VIA Technologies, Inc. VT8377 [KT400/KT600 AGP] Host Bridge [1106:3189]
Subsystem: ASUSTeK Computer Inc. A7V8X motherboard [1043:807f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
Capabilities: <access denied>
Kernel driver in use: agpgart-via
Kernel modules: via-agp
00:01.0 PCI bridge [0604]: VIA Technologies, Inc. VT8235 PCI Bridge [1106:b168] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: d5000000-d7dfffff
Prefetchable memory behind bridge: d7f00000-dfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel modules: shpchp
00:0a.0 Network controller [0280]: RaLink RT2500 802.11g Cardbus/mini-PCI [1814:0201] (rev 01)
Subsystem: RaLink Device [1814:2560]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d4800000 (32-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel modules: rt2500pci
00:0b.0 Mass storage controller [0180]: Promise Technology, Inc. PDC20268 (Ultra100 TX2) [105a:4d68] (rev 01) (prog-if 85)
Subsystem: Promise Technology, Inc. Ultra100TX2 [105a:4d68]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (1000ns min, 4500ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at d800 [size=8]
Region 1: I/O ports at d400 [size=4]
Region 2: I/O ports at d000 [size=8]
Region 3: I/O ports at b800 [size=4]
Region 4: I/O ports at b400 [size=16]
Region 5: Memory at d4000000 (32-bit, non-prefetchable) [size=16K]
[virtual] Expansion ROM at 50000000 [disabled] [size=16K]
Capabilities: <access denied>
Kernel driver in use: Promise_IDE
Kernel modules: pdc202xx_new
00:0e.0 Multimedia audio controller [0401]: Creative Labs SB Live! EMU10k1 [1102:0002] (rev 0a)
Subsystem: Creative Labs SBLive! 5.1 Digital Model SB0220 [1102:8065]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at b000 [size=32]
Capabilities: <access denied>
Kernel driver in use: EMU10K1_Audigy
Kernel modules: snd-emu10k1
00:0e.1 Input device controller [0980]: Creative Labs SB Live! Game Port [1102:7002] (rev 0a)
Subsystem: Creative Labs Gameport Joystick [1102:0020]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Region 0: I/O ports at a800 [size=8]
Capabilities: <access denied>
Kernel driver in use: Emu10k1_gameport
Kernel modules: emu10k1-gp
00:0f.0 Network controller [0280]: Intersil Corporation ISL3890 [Prism GT/Prism Duette]/ISL3886 [Prism Javelin/Prism Xbow] [1260:3890] (rev 01)
Subsystem: Accton Technology Corporation SMC2802W V2 Wireless PCI Adapter [ISL3886] [1113:ee03]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 32 (2500ns min, 7000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at d3800000 (32-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: prism54pci
Kernel modules: p54pci
00:10.0 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 80) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. A7V8X-X motherboard [1043:80a1]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 21
Region 4: I/O ports at a400 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:10.1 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 80) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. A7V8X-X motherboard [1043:80a1]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at a000 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:10.2 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 80) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. A7V8X-X motherboard [1043:80a1]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin C routed to IRQ 21
Region 4: I/O ports at 9800 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:10.3 USB Controller [0c03]: VIA Technologies, Inc. USB 2.0 [1106:3104] (rev 82) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. A7V8X-X motherboard rev 1.01 [1043:80a1]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin D routed to IRQ 21
Region 0: Memory at d3000000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:11.0 ISA bridge [0601]: VIA Technologies, Inc. VT8235 ISA Bridge [1106:3177]
Subsystem: ASUSTeK Computer Inc. A7V8X-X motherboard [1043:80a1]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel modules: via-ircc, i2c-viapro
00:11.1 IDE interface [0101]: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE [1106:0571] (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. A7V8X-X motherboard rev. 1.01 [1043:80a1]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 255
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
Region 4: I/O ports at 9400 [size=16]
Capabilities: <access denied>
Kernel driver in use: VIA_IDE
Kernel modules: via82cxxx
00:12.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6102 [Rhine-II] [1106:3065] (rev 74)
Subsystem: ASUSTeK Computer Inc. A7V8X-X Motherboard [1043:80a1]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (750ns min, 2000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 23
Region 0: I/O ports at 9000 [size=256]
Region 1: Memory at d2800000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: via-rhine
Kernel modules: via-rhine
01:00.0 VGA compatible controller [0300]: nVidia Corporation NV40 [GeForce 6800] [10de:0041] (rev a1) (prog-if 00 [VGA controller])
Subsystem: Giga-byte Technology Device [1458:310f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 248 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d6000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d8000000 (32-bit, prefetchable) [size=128M]
Region 2: Memory at d5000000 (32-bit, non-prefetchable) [size=16M]
[virtual] Expansion ROM at d7fe0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: nvidia
Kernel modules: nvidiafb, nvidia
- -- System Information:
Debian Release: lenny/sid
APT prefers testing
APT policy: (530, 'testing'), (520, 'unstable'), (510, 'experimental')
Architecture: i386 (i686)
Kernel: Linux 2.6.26-1-686 (SMP w/1 CPU core)
Locale: LANG=en_GB.UTF-8, LC_CTYPE=en_GB.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.26-1-686 depends on:
ii debconf [debconf-2.0] 1.5.24 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92j tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.26-1-686 recommends:
ii libc6-i686 2.7-16 GNU C Library: Shared libraries [i
Versions of packages linux-image-2.6.26-1-686 suggests:
ii grub-pc [grub] 1.96+20080724-12 GRand Unified Bootloader, version
ii linux-doc-2.6.26 2.6.26-10 Linux kernel specific documentatio
- -- debconf information:
linux-image-2.6.26-1-686/preinst/abort-overwrite-2.6.26-1-686:
linux-image-2.6.26-1-686/postinst/bootloader-error-2.6.26-1-686:
linux-image-2.6.26-1-686/postinst/depmod-error-initrd-2.6.26-1-686: false
linux-image-2.6.26-1-686/postinst/old-system-map-link-2.6.26-1-686: true
linux-image-2.6.26-1-686/prerm/would-invalidate-boot-loader-2.6.26-1-686: true
linux-image-2.6.26-1-686/preinst/elilo-initrd-2.6.26-1-686: true
linux-image-2.6.26-1-686/postinst/old-dir-initrd-link-2.6.26-1-686: true
linux-image-2.6.26-1-686/postinst/kimage-is-a-directory:
linux-image-2.6.26-1-686/postinst/create-kimage-link-2.6.26-1-686: true
linux-image-2.6.26-1-686/preinst/overwriting-modules-2.6.26-1-686: true
linux-image-2.6.26-1-686/postinst/depmod-error-2.6.26-1-686: false
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.26-1-686/prerm/removing-running-kernel-2.6.26-1-686: true
linux-image-2.6.26-1-686/preinst/abort-install-2.6.26-1-686:
linux-image-2.6.26-1-686/preinst/lilo-has-ramdisk:
linux-image-2.6.26-1-686/preinst/bootloader-initrd-2.6.26-1-686: true
linux-image-2.6.26-1-686/preinst/lilo-initrd-2.6.26-1-686: true
linux-image-2.6.26-1-686/postinst/old-initrd-link-2.6.26-1-686: true
linux-image-2.6.26-1-686/postinst/bootloader-test-error-2.6.26-1-686:
linux-image-2.6.26-1-686/preinst/failed-to-move-modules-2.6.26-1-686:
linux-image-2.6.26-1-686/preinst/initrd-2.6.26-1-686:
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)
iEYEARECAAYFAkk3EMgACgkQshl/216gEHiV2QCgnE48pl4eDdZkvtmODvuroZdb
jnoAoPKdre/AP6DXUejyQr1JrEhJray8
=PUxk
-----END PGP SIGNATURE-----
Reply to: