Bug#490686: linux-image-2.6.25-2-686 does not work with KLaptop
Package: linux-image-2.6.25-2-686
Version: 2.6.25-6
Severity: important
linux-image-2.6.25-2-686 does not work with KLaptop. I'm not sure why. It's always worked with the
other stock Debian kernels and ACPI does work with this kernel, but when I run the "klaptop_check"
command, KLaptop fails to start.
When I open the "Low Battery Warning" and "Low Battery Critical" tabs
of the "Laptop Battery" page in KDE's Control Center, I see the following message:
"Your computer seems to have a partial ACPI installation. ACPI was probably enabled, but some of the
sub-options were not - you need to enable at least 'AC Adaptor' and 'Control Method Battery' and then
rebuild your kernel."
I looked through the "/boot/config-2.6.24-1-686" and "/boot/config-2.6.25-2-686" files to find those
options, but I couldn't find them in either file. (In other words, I cannot find those options in the
config file of the kernel that works with KLaptop, nor can I find them in the config file of the
kernel that doesn't work with KLaptop).
Just to confirm that ACPI works:
[ Sun 13-Jul-2008 12.58 eric ] ~ $ acpi
Battery 0: Discharging, 73%, 00:00:47 remaining
[ Sun 13-Jul-2008 12.58 eric ] ~ $
Let me know if I can provide you with any more information or otherwise be of assistance to you.
Thanks!
- Eric
-- Package-specific info:
** Version:
Linux version 2.6.25-2-686 (Debian 2.6.25-6) (maks@debian.org) (gcc version 4.1.3 20080623 (prerelease) (Debian 4.1.2-23)) #1 SMP Fri Jun 27 03:23:20 UTC 2008
** Command line:
root=/dev/hda2 ro vga=791 splash laptop
** Tainted: P (1)
** Kernel log:
[ 19.623768] ACPI: Power Button (CM) [PBTN]
[ 19.623909] input: Sleep Button (CM) as /class/input/input6
[ 19.651847] ACPI: Sleep Button (CM) [SBTN]
[ 20.534779] ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
[ 20.534814] PCI: Setting latency timer of device 0000:00:1f.6 to 64
[ 20.608082] ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
[ 20.608122] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[ 21.363844] intel8x0_measure_ac97_clock: measured 55462 usecs
[ 21.363854] intel8x0: clocking to 48000
[ 21.677330] input: Video Bus as /class/input/input7
[ 21.711943] ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
[ 22.010199] Real Time Clock Driver v1.12ac
[ 22.052203] input: PC Speaker as /class/input/input8
[ 22.271957] Yenta: CardBus bridge found at 0000:02:01.0 [1028:00e3]
[ 22.271983] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 22.271988] Yenta: Routing CardBus interrupts to PCI
[ 22.271994] Yenta TI: socket 0000:02:01.0, mfunc 0x01261222, devctl 0x64
[ 22.504409] Yenta: ISA IRQ mask 0x0498, PCI irq 11
[ 22.504420] Socket status: 30000006
[ 22.504428] pcmcia: parent PCI bridge I/O window: 0xe000 - 0xffff
[ 22.504434] cs: IO port probe 0xe000-0xffff: clean.
[ 22.505315] pcmcia: parent PCI bridge Memory window: 0xf4000000 - 0xfbffffff
[ 22.505321] pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x59ffffff
[ 22.528706] Yenta: CardBus bridge found at 0000:02:01.1 [1028:00e3]
[ 22.528730] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 22.528734] Yenta: Routing CardBus interrupts to PCI
[ 22.528741] Yenta TI: socket 0000:02:01.1, mfunc 0x01261222, devctl 0x64
[ 22.760439] Yenta: ISA IRQ mask 0x0498, PCI irq 11
[ 22.760449] Socket status: 30000020
[ 22.760457] pcmcia: parent PCI bridge I/O window: 0xe000 - 0xffff
[ 22.760463] cs: IO port probe 0xe000-0xffff: clean.
[ 22.761344] pcmcia: parent PCI bridge Memory window: 0xf4000000 - 0xfbffffff
[ 22.761350] pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x59ffffff
[ 22.793659] parport_pc 00:0e: reported by Plug and Play ACPI
[ 22.793718] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[ 23.399977] pccard: CardBus card inserted into slot 1
[ 23.725345] Synaptics Touchpad, model: 1, fw: 5.7, id: 0x9b48b1, caps: 0x804793/0x0
[ 23.725361] serio: Synaptics pass-through port at isa0060/serio1/input0
[ 23.764506] input: SynPS/2 Synaptics TouchPad as /class/input/input9
[ 24.470755] cs: IO port probe 0x100-0x3af: clean.
[ 24.471637] cs: IO port probe 0x3e0-0x4ff: clean.
[ 24.472069] cs: IO port probe 0x820-0x8ff: clean.
[ 24.472139] cs: IO port probe 0xc00-0xcf7: clean.
[ 24.472636] cs: IO port probe 0xa00-0xaff: clean.
[ 24.509502] cs: IO port probe 0x100-0x3af: clean.
[ 24.510394] cs: IO port probe 0x3e0-0x4ff: clean.
[ 24.510780] cs: IO port probe 0x820-0x8ff: clean.
[ 24.510849] cs: IO port probe 0xc00-0xcf7: clean.
[ 24.511566] cs: IO port probe 0xa00-0xaff: clean.
[ 24.740253] ath_hal: module license 'Proprietary' taints kernel.
[ 24.743209] ath_hal: 0.9.18.0 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
[ 24.792396] wlan: 0.9.4
[ 24.816146] ath_pci: 0.9.4
[ 24.816211] PCI: Enabling device 0000:07:00.0 (0000 -> 0002)
[ 24.816229] ACPI: PCI Interrupt 0000:07:00.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
[ 25.433936] ath_rate_sample: 1.2 (0.9.4)
[ 25.517107] wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
[ 25.517124] wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
[ 25.517143] wifi0: H/W encryption support: WEP AES AES_CCM TKIP
[ 25.517152] wifi0: mac 7.8 phy 4.5 radio 5.6
[ 25.517163] wifi0: Use hw queue 1 for WME_AC_BE traffic
[ 25.517167] wifi0: Use hw queue 0 for WME_AC_BK traffic
[ 25.517172] wifi0: Use hw queue 2 for WME_AC_VI traffic
[ 25.517176] wifi0: Use hw queue 3 for WME_AC_VO traffic
[ 25.517181] wifi0: Use hw queue 8 for CAB traffic
[ 25.517185] wifi0: Use hw queue 9 for beacons
[ 25.554034] wifi0: Atheros 5212: mem=0x5c000000, irq=11
[ 25.577900] udev: renamed network interface ath0 to ath1
[ 25.947894] hdc: UDMA/33 mode selected
[ 26.970619] Adding 666656k swap on /dev/hda5. Priority:-1 extents:1 across:666656k
[ 27.826600] EXT3 FS on hda2, internal journal
[ 29.072201] loop: module loaded
[ 29.251876] IBM TrackPoint firmware: 0x0b, buttons: 2/3
[ 29.279896] device-mapper: uevent: version 1.0.3
[ 29.282604] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
[ 29.460650] input: TPPS/2 IBM TrackPoint as /class/input/input10
[ 30.364244] fuse init (API version 7.9)
[ 30.702399] kjournald starting. Commit interval 5 seconds
[ 30.703283] EXT3 FS on hda6, internal journal
[ 30.703283] EXT3-fs: mounted filesystem with ordered data mode.
[ 32.286044] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 32.496033] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 32.856757] eth0: setting half-duplex.
[ 35.341954] ACPI: Invalid _PSS data: freq is zero
[ 38.492023] lp0: using parport0 (interrupt-driven).
[ 38.546623] ppdev: user-space parallel port driver
[ 47.527427] Bluetooth: Core ver 2.11
[ 47.531462] NET: Registered protocol family 31
[ 47.531476] Bluetooth: HCI device and connection manager initialized
[ 47.531485] Bluetooth: HCI socket layer initialized
[ 47.589548] Bluetooth: L2CAP ver 2.9
[ 47.589562] Bluetooth: L2CAP socket layer initialized
[ 47.631261] Bluetooth: RFCOMM socket layer initialized
[ 47.631302] Bluetooth: RFCOMM TTY layer initialized
[ 47.631308] Bluetooth: RFCOMM ver 1.8
[ 609.478481] ath_rate_sample: no rates for 00:11:95:51:df:fb?
[ 1250.983367] NET: Registered protocol family 10
[ 1250.984878] lo: Disabled Privacy Extensions
[ 1250.986343] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 1261.697645] ath1: no IPv6 routers present
** Loaded modules:
Module Size Used by
ipv6 241956 8
wlan_tkip 11584 0
xt_limit 2628 12
xt_tcpudp 3104 16
ipt_LOG 5700 12
ipt_MASQUERADE 3776 0
xt_DSCP 3360 0
ipt_REJECT 3840 1
nf_conntrack_irc 6716 0
nf_conntrack_ftp 8804 0
xt_state 2496 8
rfcomm 36368 0
l2cap 22784 5 rfcomm
bluetooth 52900 4 rfcomm,l2cap
ppdev 8676 0
lp 11012 0
cpufreq_stats 5216 0
cpufreq_ondemand 8428 0
cpufreq_userspace 3812 0
freq_table 4512 2 cpufreq_stats,cpufreq_ondemand
cpufreq_conservative 7432 0
cpufreq_powersave 1856 0
iptable_nat 6728 0
nf_nat 18136 2 ipt_MASQUERADE,iptable_nat
nf_conntrack_ipv4 16616 11 iptable_nat,nf_nat
nf_conntrack 59892 7 ipt_MASQUERADE,nf_conntrack_irc,nf_conntrack_ftp,xt_state,iptable_nat,nf_nat,nf_conntrack_ipv4
iptable_mangle 3264 0
iptable_filter 3424 1
ip_tables 13168 3 iptable_nat,iptable_mangle,iptable_filter
x_tables 15716 9 xt_limit,xt_tcpudp,ipt_LOG,ipt_MASQUERADE,xt_DSCP,ipt_REJECT,xt_state,iptable_nat,ip_tables
fuse 44348 1
dm_snapshot 17444 0
dm_mirror 25316 0
dm_mod 55656 2 dm_snapshot,dm_mirror
loop 16708 0
wlan_scan_sta 12224 1
ath_rate_sample 11008 1
ath_pci 83552 0
wlan 177872 5 wlan_tkip,wlan_scan_sta,ath_rate_sample,ath_pci
ath_hal 191408 3 ath_rate_sample,ath_pci
pcmcia 36044 0
firmware_class 9088 1 pcmcia
psmouse 35920 0
serio_raw 6532 0
parport_pc 25860 1
parport 33868 3 ppdev,lp,parport_pc
yenta_socket 24300 3
rsrc_nonstatic 11584 1 yenta_socket
pcmcia_core 36436 3 pcmcia,yenta_socket,rsrc_nonstatic
pcspkr 3136 0
rtc 14272 0
video 19728 0
output 3712 1 video
snd_intel8x0 31740 1
snd_intel8x0m 16684 1
snd_ac97_codec 91300 2 snd_intel8x0,snd_intel8x0m
ac97_bus 1952 1 snd_ac97_codec
snd_pcm_oss 37824 0
snd_mixer_oss 14880 1 snd_pcm_oss
snd_pcm 68228 4 snd_intel8x0,snd_intel8x0m,snd_ac97_codec,snd_pcm_oss
snd_timer 21320 1 snd_pcm
button 8240 0
battery 8448 0
ac 4448 0
rng_core 4900 0
snd 48772 11 snd_intel8x0,snd_intel8x0m,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
soundcore 7488 1 snd
snd_page_alloc 9992 3 snd_intel8x0,snd_intel8x0m,snd_pcm
iTCO_wdt 11204 0
intel_agp 25084 1
agpgart 31720 1 intel_agp
shpchp 29716 0
pci_hotplug 26980 1 shpchp
joydev 11328 0
evdev 11328 8
dcdbas 8064 0
ext3 120360 2
jbd 43444 1 ext3
mbcache 8260 1 ext3
ide_cd_mod 32864 0
cdrom 31872 1 ide_cd_mod
ide_disk 13952 4
ata_generic 8004 0
libata 142288 1 ata_generic
scsi_mod 138668 1 libata
ide_pci_generic 4228 0 [permanent]
usbhid 40192 0
hid 36032 1 usbhid
ff_memless 5384 1 usbhid
floppy 53284 0
piix 7176 0 [permanent]
ide_core 100312 4 ide_cd_mod,ide_disk,ide_pci_generic,piix
3c59x 39976 0
mii 5248 1 3c59x
dock 10448 1 libata
uhci_hcd 22352 0
usbcore 130032 3 usbhid,uhci_hcd
thermal 19100 0
processor 39660 2 thermal
fan 5636 0
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82830 830 Chipset Host Bridge [8086:3575] (rev 04)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
Kernel modules: intel-agp
00:01.0 PCI bridge [0604]: Intel Corporation 82830 830 Chipset AGP Bridge [8086:3576] (rev 04)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fc000000-fdffffff
Prefetchable memory behind bridge: e0000000-e7ffffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Kernel modules: shpchp
00:1d.0 USB Controller [0c03]: Intel Corporation 82801CA/CAM USB Controller #1 [8086:2482] (rev 02)
Subsystem: Intel Corporation Device [8086:4541]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 4: I/O ports at bf80 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev 42)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=10, sec-latency=32
I/O behind bridge: 0000e000-0000ffff
Memory behind bridge: f4000000-fbffffff
Prefetchable memory behind bridge: 50000000-59ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Kernel modules: shpchp
00:1f.0 ISA bridge [0601]: Intel Corporation 82801CAM ISA Bridge (LPC) [8086:248c] (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Kernel modules: intel-rng, iTCO_wdt
00:1f.1 IDE interface [0101]: Intel Corporation 82801CAM IDE U100 Controller [8086:248a] (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Intel Corporation Device [8086:4541]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at bfa0 [size=16]
Region 5: Memory at 5a000000 (32-bit, non-prefetchable) [size=1K]
Kernel driver in use: PIIX_IDE
Kernel modules: piix
00:1f.5 Multimedia audio controller [0401]: Intel Corporation 82801CA/CAM AC'97 Audio Controller [8086:2485] (rev 02)
Subsystem: Cirrus Logic Device [1013:5959]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 5
Region 0: I/O ports at d800 [size=256]
Region 1: I/O ports at dc80 [size=64]
Kernel driver in use: Intel ICH
Kernel modules: snd-intel8x0
00:1f.6 Modem [0703]: Intel Corporation 82801CA/CAM AC'97 Modem Controller [8086:2486] (rev 02)
Subsystem: PCTel Inc Device [134d:4c21]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 5
Region 0: I/O ports at d400 [size=256]
Region 1: I/O ports at dc00 [size=128]
Kernel driver in use: Intel ICH Modem
Kernel modules: snd-intel8x0m
01:00.0 VGA compatible controller [0300]: ATI Technologies Inc Radeon Mobility M6 LY [1002:4c59]
Subsystem: Dell Device [1028:00e3]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping+ SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at c000 [size=256]
Region 2: Memory at fcff0000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at fc000000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel modules: radeonfb
02:00.0 Ethernet controller [0200]: 3Com Corporation 3c905C-TX/TX-M [Tornado] [10b7:9200] (rev 78)
Subsystem: Dell Device [1028:00e3]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (2500ns min, 2500ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at ec80 [size=128]
Region 1: Memory at f8fffc00 (32-bit, non-prefetchable) [size=128]
Expansion ROM at 58000000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: 3c59x
Kernel modules: 3c59x
02:01.0 CardBus bridge [0607]: Texas Instruments PCI1420 PC card Cardbus Controller [104c:ac51]
Subsystem: Dell Device [1028:00e3]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f8000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
Memory window 0: 50000000-53fff000 (prefetchable)
Memory window 1: f4000000-f7fff000
I/O window 0: 0000e000-0000e0ff
I/O window 1: 0000e400-0000e4ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
Kernel modules: yenta_socket
02:01.1 CardBus bridge [0607]: Texas Instruments PCI1420 PC card Cardbus Controller [104c:ac51]
Subsystem: Dell Device [1028:00e3]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f8001000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=07, subordinate=0a, sec-latency=176
Memory window 0: 54000000-57fff000 (prefetchable)
Memory window 1: 5c000000-5ffff000
I/O window 0: 0000e800-0000e8ff
I/O window 1: 00001000-000010ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
Kernel modules: yenta_socket
07:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR2413 802.11bg NIC [168c:001a] (rev 01)
Subsystem: D-Link System Inc Device [1186:3b08]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168 (2500ns min, 7000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 5c000000 (32-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: ath_pci
Kernel modules: ath_pci, ath5k
-- System Information:
Debian Release: lenny/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: i386 (i686)
Kernel: Linux 2.6.25-2-686 (SMP w/1 CPU core)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.25-2-686 depends on:
ii debconf [debconf-2.0] 1.5.22 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92e tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.25-2-686 recommends:
ii libc6-i686 2.7-10 GNU C Library: Shared libraries [i
-- debconf information:
linux-image-2.6.25-2-686/preinst/abort-install-2.6.25-2-686:
linux-image-2.6.25-2-686/postinst/bootloader-test-error-2.6.25-2-686:
linux-image-2.6.25-2-686/prerm/removing-running-kernel-2.6.25-2-686: true
linux-image-2.6.25-2-686/postinst/old-initrd-link-2.6.25-2-686: true
linux-image-2.6.25-2-686/preinst/initrd-2.6.25-2-686:
linux-image-2.6.25-2-686/postinst/kimage-is-a-directory:
linux-image-2.6.25-2-686/postinst/depmod-error-2.6.25-2-686: false
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.25-2-686/preinst/overwriting-modules-2.6.25-2-686: true
linux-image-2.6.25-2-686/prerm/would-invalidate-boot-loader-2.6.25-2-686: true
linux-image-2.6.25-2-686/preinst/elilo-initrd-2.6.25-2-686: true
linux-image-2.6.25-2-686/postinst/depmod-error-initrd-2.6.25-2-686: false
linux-image-2.6.25-2-686/preinst/bootloader-initrd-2.6.25-2-686: true
linux-image-2.6.25-2-686/preinst/lilo-has-ramdisk:
linux-image-2.6.25-2-686/postinst/bootloader-error-2.6.25-2-686:
linux-image-2.6.25-2-686/preinst/lilo-initrd-2.6.25-2-686: true
linux-image-2.6.25-2-686/postinst/old-system-map-link-2.6.25-2-686: true
linux-image-2.6.25-2-686/postinst/create-kimage-link-2.6.25-2-686: true
linux-image-2.6.25-2-686/postinst/old-dir-initrd-link-2.6.25-2-686: true
linux-image-2.6.25-2-686/preinst/abort-overwrite-2.6.25-2-686:
linux-image-2.6.25-2-686/preinst/failed-to-move-modules-2.6.25-2-686:
Reply to: