Bug#472462: linux-image-2.6.24-1-amd64: log cluttered with ide failed opcode for dvd drive
Package: linux-image-2.6.24-1-amd64
Version: 2.6.24-4
Severity: normal
In my log, I'm seeing about 4 of these messages every 2 minutes. It's
annoying as it clutters the kernel log and prevents seeing other issues that
might show up:
Mar 24 08:33:26 cerberus kernel: hda: drive not ready for command
Mar 24 08:33:26 cerberus kernel: hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
Mar 24 08:33:26 cerberus kernel: ide: failed opcode was: unknown
Mar 24 08:33:26 cerberus kernel: hda: drive not ready for command
On my machine, hda is the dvd drive. This is the only ide device attached.
The hard drives are sata and numbered sda and sdb.
This is the ide section from dmesg:
JMB: IDE controller (0x197b:0x2368 rev 0x00) at PCI slot 0000:02:00.0
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
JMB: 100% native mode on irq 16
ide0: BM-DMA at 0xc400-0xc407, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xc408-0xc40f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
sdb5 >
sd 1:0:0:0: [sdb] Attached SCSI disk
firewire_core: created new fw device fw0 (0 config rom retries, S400)
hda: LITE-ON DVDRW LH-20A1H, ATAPI CD/DVD-ROM drive
hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/66 mode selected
ide0 at 0xc000-0xc007,0xc102 on irq 16
Probing IDE interface ide1...
hda: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
-- Package-specific info:
** Version:
Linux version 2.6.24-1-amd64 (Debian 2.6.24-4) (waldi@debian.org) (gcc version 4.1.3 20080114 (prerelease) (Debian 4.1.2-19)) #1 SMP Mon Feb 11 13:47:43 UTC 2008
** Command line:
root=/dev/md0 ro quiet
** Not tainted
** Kernel log:
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: drive not ready for command
hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: drive not ready for command
** Loaded modules:
Module Size Used by
nls_iso8859_1 9728 0
nls_cp437 11392 0
vfat 17920 0
fat 58288 1 vfat
usb_storage 91968 0
i915 31104 2
drm 98856 3 i915
ppdev 13832 0
lp 17476 0
nfsd 261416 13
lockd 73136 2 nfsd
nfs_acl 8192 1 nfsd
auth_rpcgss 53152 1 nfsd
sunrpc 201096 9 nfsd,lockd,nfs_acl,auth_rpcgss
exportfs 9472 1 nfsd
ac 11400 0
battery 19976 0
cpufreq_ondemand 13712 0
cpufreq_userspace 9604 0
cpufreq_stats 10528 0
freq_table 9728 2 cpufreq_ondemand,cpufreq_stats
cpufreq_powersave 6272 0
cpufreq_conservative 13320 0
ipv6 286248 33
coretemp 12544 0
it87 28432 0
hwmon_vid 7424 1 it87
firewire_sbp2 20624 0
loop 22788 0
parport_pc 42408 1
i2c_i801 13852 0
rtc_cmos 13112 0
parport 44812 3 ppdev,lp,parport_pc
iTCO_wdt 17488 0
rtc_core 24716 1 rtc_cmos
i2c_core 29824 1 i2c_i801
rtc_lib 7680 1 rtc_core
snd_hda_intel 362024 4
pcspkr 7808 0
snd_pcm 89352 2 snd_hda_intel
snd_timer 28552 2 snd_pcm
usblp 19840 0
snd 65896 9 snd_hda_intel,snd_pcm,snd_timer
soundcore 13216 1 snd
snd_page_alloc 15248 2 snd_hda_intel,snd_pcm
intel_agp 32288 1
button 13984 0
evdev 17024 3
ext3 139024 1
jbd 55976 1 ext3
mbcache 13952 1 ext3
raid1 27648 1
md_mod 84380 2 raid1
ide_cd 44704 0
cdrom 39464 1 ide_cd
jmicron 7168 0 [permanent]
sd_mod 33408 6
generic 9732 0 [permanent]
ide_core 144920 3 ide_cd,jmicron,generic
usbhid 35168 0
hid 41792 1 usbhid
ahci 34436 4
ata_generic 13060 0
firewire_ohci 24192 0
firewire_core 49472 2 firewire_sbp2,firewire_ohci
crc_itu_t 6656 1 firewire_core
r8169 36740 0
libata 162736 2 ahci,ata_generic
scsi_mod 170296 4 usb_storage,firewire_sbp2,sd_mod,libata
ehci_hcd 39692 0
uhci_hcd 30112 0
thermal 22688 0
processor 45032 1 thermal
fan 9864 0
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82G33/G31/P35/P31 Express DRAM Controller [8086:29c0] (rev 02)
Subsystem: Giga-byte Technology Unknown device [1458:5000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
Kernel modules: intel-agp
00:02.0 VGA compatible controller [0300]: Intel Corporation 82G33/G31 Express Integrated Graphics Controller [8086:29c2] (rev 02) (prog-if 00 [VGA controller])
Subsystem: Giga-byte Technology Unknown device [1458:d000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f3100000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at e200 [size=8]
Region 2: Memory at e0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at f3000000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <access denied>
00:02.1 Display controller [0380]: Intel Corporation 82G33/G31 Express Integrated Graphics Controller [8086:29c3] (rev 02)
Subsystem: Giga-byte Technology Unknown device [1458:d000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at f3180000 (32-bit, non-prefetchable) [size=512K]
Capabilities: <access denied>
00:1a.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 [8086:2937] (rev 02) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Unknown device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at e600 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 [8086:2938] (rev 02) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Unknown device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at e000 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.2 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 [8086:2939] (rev 02) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Unknown device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at e100 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 [8086:293c] (rev 02) (prog-if 20 [EHCI])
Subsystem: Giga-byte Technology Unknown device [1458:5006]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 0: Memory at f3205000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1b.0 Audio device [0403]: Intel Corporation 82801I (ICH9 Family) HD Audio Controller [8086:293e] (rev 02)
Subsystem: Giga-byte Technology Unknown device [1458:a022]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at f3200000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:1c.0 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 [8086:2940] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000b000-0000bfff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.4 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 [8086:2948] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: f0000000-f0ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1d.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 [8086:2934] (rev 02) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Unknown device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at e300 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 [8086:2935] (rev 02) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Unknown device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at e400 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 [8086:2936] (rev 02) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Unknown device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at e500 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 [8086:293a] (rev 02) (prog-if 20 [EHCI])
Subsystem: Giga-byte Technology Unknown device [1458:5006]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f3204000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev 92) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: f1000000-f2ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801IB (ICH9) LPC Interface Controller [8086:2918] (rev 02)
Subsystem: Giga-byte Technology Unknown device [1458:5001]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel modules: iTCO_wdt
00:1f.2 SATA controller [0106]: Intel Corporation 82801IB (ICH9) 4 port SATA AHCI Controller [8086:2923] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Giga-byte Technology Unknown device [1458:b005]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 1277
Region 0: I/O ports at e700 [size=8]
Region 1: I/O ports at e800 [size=4]
Region 2: I/O ports at e900 [size=8]
Region 3: I/O ports at ea00 [size=4]
Region 4: I/O ports at eb00 [size=32]
Region 5: Memory at f3206000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
Kernel modules: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 82801I (ICH9 Family) SMBus Controller [8086:2930] (rev 02)
Subsystem: Giga-byte Technology Unknown device [1458:5001]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at f3207000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 0500 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801
02:00.0 IDE interface [0101]: JMicron Technologies, Inc. JMB368 IDE controller [197b:2368] (prog-if 85 [Master SecO PriO])
Subsystem: Giga-byte Technology Unknown device [1458:b000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at c000 [size=8]
Region 1: I/O ports at c100 [size=4]
Region 2: I/O ports at c200 [size=8]
Region 3: I/O ports at c300 [size=4]
Region 4: I/O ports at c400 [size=16]
Capabilities: <access denied>
Kernel driver in use: JMicron IDE
Kernel modules: ata_generic, generic, jmicron
03:05.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8110SC/8169SC Gigabit Ethernet [10ec:8167] (rev 10)
Subsystem: Giga-byte Technology Unknown device [1458:e000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (8000ns min, 16000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at d000 [size=256]
Region 1: Memory at f2005000 (32-bit, non-prefetchable) [size=256]
[virtual] Expansion ROM at f1000000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: r8169
Kernel modules: r8169
03:07.0 FireWire (IEEE 1394) [0c00]: Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link) [104c:8024] (prog-if 10 [OHCI])
Subsystem: Giga-byte Technology Unknown device [1458:1000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (500ns min, 1000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f2004000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at f2000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
Kernel modules: firewire-ohci
-- System Information:
Debian Release: lenny/sid
APT prefers testing
APT policy: (990, 'testing'), (500, 'unstable'), (500, 'stable')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.24-1-amd64 (SMP w/2 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.24-1-amd64 depends on:
ii debconf [debconf-2.0] 1.5.19 Debian configuration management sy
ii initramfs-tools [linux-initr 0.91e tools for generating an initramfs
ii module-init-tools 3.3-pre11-4 tools for managing Linux kernel mo
linux-image-2.6.24-1-amd64 recommends no packages.
-- debconf information:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.24-1-amd64/preinst/abort-overwrite-2.6.24-1-amd64:
linux-image-2.6.24-1-amd64/postinst/old-dir-initrd-link-2.6.24-1-amd64: true
linux-image-2.6.24-1-amd64/preinst/failed-to-move-modules-2.6.24-1-amd64:
linux-image-2.6.24-1-amd64/postinst/bootloader-test-error-2.6.24-1-amd64:
linux-image-2.6.24-1-amd64/preinst/lilo-initrd-2.6.24-1-amd64: true
linux-image-2.6.24-1-amd64/postinst/create-kimage-link-2.6.24-1-amd64: true
linux-image-2.6.24-1-amd64/postinst/depmod-error-initrd-2.6.24-1-amd64: false
linux-image-2.6.24-1-amd64/postinst/old-system-map-link-2.6.24-1-amd64: true
linux-image-2.6.24-1-amd64/preinst/lilo-has-ramdisk:
linux-image-2.6.24-1-amd64/preinst/overwriting-modules-2.6.24-1-amd64: true
linux-image-2.6.24-1-amd64/postinst/bootloader-error-2.6.24-1-amd64:
linux-image-2.6.24-1-amd64/preinst/abort-install-2.6.24-1-amd64:
linux-image-2.6.24-1-amd64/postinst/old-initrd-link-2.6.24-1-amd64: true
linux-image-2.6.24-1-amd64/postinst/kimage-is-a-directory:
linux-image-2.6.24-1-amd64/preinst/bootloader-initrd-2.6.24-1-amd64: true
linux-image-2.6.24-1-amd64/prerm/would-invalidate-boot-loader-2.6.24-1-amd64: true
linux-image-2.6.24-1-amd64/preinst/initrd-2.6.24-1-amd64:
linux-image-2.6.24-1-amd64/prerm/removing-running-kernel-2.6.24-1-amd64: true
linux-image-2.6.24-1-amd64/preinst/elilo-initrd-2.6.24-1-amd64: true
linux-image-2.6.24-1-amd64/postinst/depmod-error-2.6.24-1-amd64: false
Reply to: