[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Bug#272518: marked as done (kernel: dpt_i2o causes oops under high stress)



Your message dated Fri, 26 Dec 2008 20:40:58 +0100
with message-id <20081226194058.GA5416@galadriel.inutil.org>
and subject line Bounces
has caused the Debian Bug report #272518,
regarding kernel: dpt_i2o causes oops under high stress
to be marked as done.

This means that you claim that the problem has been dealt with.
If this is not the case it is now your responsibility to reopen the
Bug report if necessary, and/or fix the problem forthwith.

(NB: If you are a system administrator and have no idea what this
message is talking about, this may indicate a serious mail system
misconfiguration somewhere. Please contact owner@bugs.debian.org
immediately.)


-- 
272518: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=272518
Debian Bug Tracking System
Contact owner@bugs.debian.org with problems
--- Begin Message ---
Package: kernel
Severity: normal

Using the i2o card configured to use JBOD, I was configuring software
RAID 0 (I was getting poor performance with hardware so wanted to
do a comparision). However fairly soon after starting tiobench, the
kernel oopsed.

Full boot and shell log included.

-- System Information:
Debian Release: 3.1
  APT prefers unstable
  APT policy: (500, 'unstable')
Architecture: i386 (i686)
Kernel: Linux 2.6.8-1-k7-smp
Locale: LANG=C, LC_CTYPE=C
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009e800 (usable)
 BIOS-e820: 000000000009e800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000d8000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003fef0000 (usable)
 BIOS-e820: 000000003fef0000 - 000000003feff000 (ACPI data)
 BIOS-e820: 000000003feff000 - 000000003ff00000 (ACPI NVS)
 BIOS-e820: 000000003ff00000 - 000000003ff80000 (usable)
 BIOS-e820: 000000003ff80000 - 0000000040000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec04000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f7170
DMI 2.3 present.
ACPI: RSDP (v000 PTLTD                                     ) @ 0x000f7100
ACPI: RSDT (v001 PTLTD    RSDT   0x06040000  LTP 0x00000000) @ 0x3fefcf28
ACPI: FADT (v001 AMD    TECATE   0x06040000 PTL  0x000f4240) @ 0x3fefef2e
ACPI: MADT (v001 PTLTD  	 APIC   0x06040000  LTP 0x00000000) @ 0x3fefefa2
ACPI: DSDT (v001    AMD  AMDACPI 0x06040000 MSFT 0x0100000d) @ 0x00000000
ACPI: PM-Timer IO Port: 0x8008
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x01] enabled)
Processor #1 6:8 APIC version 16
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:8 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: Assigned apic_id 2
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists
Kernel command line: root=/dev/sda2 ro console=ttyS0,115200 
Initializing CPU#0
PID hash table entries: 4096 (order 12: 32768 bytes)
Detected 2000.282 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1030128k/1048064k available (1637k kernel code, 16960k reserved, 775k data, 168k init, 130496k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 3956.73 BogoMIPS
Security Scaffold v1.0.0 initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
CPU0: AMD Athlon(tm) MP 2400+ stepping 01
per-CPU timeslice cutoff: 731.38 usecs.
task migration cache decay timeout: 1 msecs.
masked ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Booting processor 1/0 eip 3000
Initializing CPU#1
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 3997.69 BogoMIPS
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: AMD Athlon(tm) Processor stepping 01
Total of 2 processors activated (7954.43 BogoMIPS).
ENABLING IO-APIC IRQs
...TIMER: vector=0x31 pin1=2 pin2=-1
Using local APIC timer interrupts.
calibrating APIC timer ...
...... CPU clock speed is 1999.0827 MHz.
...... host bus clock speed is 266.0643 MHz.
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
checking if image is initramfs...it isn't (ungzip failed); looks like an initrd
Freeing initrd memory: 4728k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfd7d0, last bus=3
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
mtrr: your CPUs had inconsistent fixed MTRR settings
mtrr: probably your BIOS does not setup all CPUs.
mtrr: corrected configuration.
ACPI: Subsystem revision 20040326
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 *5 10 11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 5 10 11) *9
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 5 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 5 *10 11)
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00f7130
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x9aad, dseg 0x400
PnPBIOS: 17 nodes reported by PnP BIOS; 17 recorded by driver
PCI: Using ACPI for IRQ routing
ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 20 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 21 (level, low) -> IRQ 177
ACPI: PCI interrupt 0000:01:05.0[A] -> GSI 18 (level, low) -> IRQ 185
ACPI: PCI interrupt 0000:03:00.0[D] -> GSI 19 (level, low) -> IRQ 193
ACPI: PCI interrupt 0000:03:04.0[A] -> GSI 16 (level, low) -> IRQ 201
ACPI: PCI interrupt 0000:03:04.1[B] -> GSI 17 (level, low) -> IRQ 209
ACPI: PCI interrupt 0000:03:05.0[A] -> GSI 17 (level, low) -> IRQ 209
ACPI: PCI interrupt 0000:03:06.0[A] -> GSI 18 (level, low) -> IRQ 185
ACPI: PCI interrupt 0000:03:06.1[B] -> GSI 19 (level, low) -> IRQ 193
ACPI: PCI interrupt 0000:03:06.2[C] -> GSI 16 (level, low) -> IRQ 201
ACPI: PCI interrupt 0000:03:07.0[A] -> GSI 19 (level, low) -> IRQ 193
testing the IO APIC.......................
Using vector-based indexing
..................................... done.
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
BIOS failed to enable PCI standards compliance, fixing this error.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: (supports S0 S1 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4728 blocks [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 168k freed
initrd-tools: 0.1.74
SCSI subsystem initialized
ACPI: PCI interrupt 0000:03:04.0[A] -> GSI 16 (level, low) -> IRQ 201
ACPI: PCI interrupt 0000:03:04.1[B] -> GSI 17 (level, low) -> IRQ 209
ACPI: PCI interrupt 0000:03:05.0[A] -> GSI 17 (level, low) -> IRQ 209
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
        <Adaptec 3960D Ultra160 SCSI adapter>
        aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs

Using anticipatory io scheduler
(scsi0:A:1): 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit)
  Vendor: FUJITSU   Model: MAN3367MP         Rev: 0107
  Type:   Direct-Access                      ANSI SCSI revision: 03
scsi0:A:1:0: Tagged Queuing enabled.  Depth 8
scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
        <Adaptec 3960D Ultra160 SCSI adapter>
        aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs

scsi2 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
        <Adaptec 2940 Ultra SCSI adapter>
        aic7880: Ultra Wide Channel A, SCSI Id=7, 16/253 SCBs

(scsi2:A:4): 20.000MB/s transfers (20.000MHz, offset 8)
  Vendor: GENERIC   Model: CRD-BP2           Rev: 2.21
  Type:   CD-ROM                             ANSI SCSI revision: 02
(scsi2:A:5): 10.000MB/s transfers (10.000MHz, offset 15)
  Vendor: MATSHITA  Model: DVD-RAM LF-D200   Rev: X120
  Type:   CD-ROM                             ANSI SCSI revision: 04
vesafb: probe of vesafb0 failed with error -6
NET: Registered protocol family 1
Attached scsi generic sg0 at scsi0, channel 0, id 1, lun 0,  type 0
Attached scsi generic sg1 at scsi2, channel 0, id 4, lun 0,  type 5
Attached scsi generic sg2 at scsi2, channel 0, id 5, lun 0,  type 5
SCSI device sda: 71771688 512-byte hdwr sectors (36747 MB)
SCSI device sda: drive cache: write back
 /dev/scsi/host0/bus0/target1/lun0: p1 p2 p3 < p5 p6 p7 p8 >
Attached scsi disk sda at scsi0, channel 0, id 1, lun 0
SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting.  Commit interval 5 seconds
EXT3-fs: sda2: orphan cleanup on readonly fs
EXT3-fs: sda2: 2 orphan inodes deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
INIT: version 2.86 booting
devfsd: No devfs on /dev, not starting.
Setting disc parameters: done.
Activating swap.
Adding 1172704k swap on /dev/sda5.  Priority:-1 extents:1
Checking root file system...
fsck 1.35 (28-Feb-2004)
/dev/sda2: clean, 23571/124928 files, 447598/498EXT3 FS on sda2, internal journal
012 blocks
/etc/init.d/rcS: System clock was not updated at this time.
Cleaning up ifupdown...done.
WARNING: Bastille-firewall is not configured yet
Please create /etc/Bastille/bastille-firewall.cfg to enable it.
(HINT: use InteractiveBastille)
Calculating module dependencies... done.
Loading modules...
    e1000
e1000: Ignoring new-style parameters in presence of obsolete ones
Intel(R) PRO/1000 Network Driver - version 5.2.52-k4
Copyright (c) 1999-2004 Intel Corporation.
ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 20 (level, low) -> IRQ 169
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
All modules loaded.
Capability LSM initialized
device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm@uk.sistina.com
Creating device-mapper devices...done.
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
Starting raid devices: 
md: md1 stopped.
mdadm: /dev/sdb has no superblocmd: md2 stopped.
k - assembly aborted
mdadm: /dev/sdd md: md0 stopped.
has no superblock - assembly aborted
mdadm: /dev/md1 has no superblock - assembly aborted
done.
Checking all file systems...
fsck 1.35 (28-Feb-2004)
/dev/sda6: recovering journal
/dev/sda6: clean, 178097/750720 files, 936770/1500061 blocks
/dev/sda7: recovering journal
/dev/sda7: clean, 22327/377856 files, 155431/755047 blocks (check in 4 mounts)
Setting kernel variables ...
.... done.
Mounting local filesystems...
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald sta/dev/sda6 on /usr type ext3 (rw)
/dev/sda7 on /var type ext3 (rw)
rting.  Commit interval 5 seconds
EXT3 FS on sda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Cleaning /tmp /var/run /var/lock.
Setting sensors limits:Can't access procfs/sysfs file
Unable to find i2c bus information;
For 2.6 kernels, make sure you have mounted sysfs and done
'modprobe i2c_sensor'!
For older kernels, make sure you have done 'modprobe i2c-proc'!
Can't access procfs/sysfs file
Unable to find i2c bus information;
For 2.6 kernels, make sure you have mounted sysfs and done
'modprobe i2c_sensor'!
For older kernels, make sure you have done 'modprobe i2c-proc'!
 done.
Running 0dns-down to make sure resolv.conf is ok...done.
/dev/shm/network/...Initializing: /etc/network/ifstate.
Starting hotplug subsystem:
   input   
     evbug: blacklisted
     evdev: loaded successfully
     evbug: blacklisted
     evdev: already loaded
   input    [success]
   isapnp  
Real Time Clock Driver v1.12
     rtc: loaded sucessfully
input: PC Speaker
     pcspkr: loaded sucessfully
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
     psmouse: loaded sucessfully
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 1 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
mice: PS/2 mouse device common for all mice
     parport_pc: loaded sucessfully
ts: Compaq touchscreen protocol output
inserting floppy driver for 2.6.8-1-k7-smp
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
     floppy: loaded sucessfully
   isapnp   [success]
   net     
   net      [success]
   pci     
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected AMD 760MP chipset
agpgart: Maximum main memory to use for agp memory: 941M
agpgart: AGP aperture is 64M @ 0xf0000000
     amd-k7-agp: loaded successfully
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: acpi_pciehprm:\_SB_.PCI0 evaluate _BBN fail=0x5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x5
modprobe: FATAL: Error inserting pciehp (/lib/modules/2.6.8-1-k7-smp/kernel/drivers/pci/hotplug/pciehp.ko): Operation not permitted

     pciehp: can't be loaded
missing kernel or user mode driver pciehp 
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
modprobe: FATAL: Error inserting shpchp (/lib/modules/2.6.8-1-k7-smp/kernel/drivers/pci/hotplug/shpchp.ko): Operation not permitted

     shpchp: can't be loaded
missing kernel or user mode driver shpchp 
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
     amd74xx: loaded successfully
hw_random: AMD768 system management I/O registers at 0x8000.
hw_random hardware driver 1.0.0 loaded
     hw_random: loaded successfully
     e1000: already loaded
Loading Adaptec I2O RAID: Version 2.4 Build 5go
Detecting Adaptec I2O RAID controllers...
ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 21 (level, low) -> IRQ 177
Adaptec I2O RAID controller 0 at f8b3b000 size=100000 irq=177
dpti: If you have a lot of devices this could take a few minutes.
dpti0: Reading the hardware resource table.
TID 008  Vendor: ADAPTEC      Device: AIC-7899     Rev: 00000001    
TID 517  Vendor: FUJITSU      Device: MAM3367MC    Rev: 0106        
TID 518  Vendor: FUJITSU      Device: MAM3367MC    Rev: 0106        
TID 519  Vendor: FUJITSU      Device: MAM3367MC    Rev: 0106        
TID 520  Vendor: FUJITSU      Device: MAM3367MC    Rev: 0106        
scsi3 : Vendor: Adaptec  Model: 2110S            FW:380E
  Vendor: FUJITSU   Model: MAM3367MC         Rev: 0106
  Type:   Direct-Access                      ANSI SCSI revision: 03
SCSI device sdb: 71770599 512-byte hdwr sectors (36747 MB)
SCSI device sdb: drive cache: write back
 /dev/scsi/host3/bus0/target8/lun0: unknown partition table
Attached scsi disk sdb at scsi3, channel 0, id 8, lun 0
Attached scsi generic sg3 at scsi3, channel 0, id 8, lun 0,  type 0
  Vendor: FUJITSU   Model: MAM3367MC         Rev: 0106
  Type:   Direct-Access                      ANSI SCSI revision: 03
SCSI device sdc: 71770599 512-byte hdwr sectors (36747 MB)
SCSI device sdc: drive cache: write back
 /dev/scsi/host3/bus0/target9/lun0: unknown partition table
Attached scsi disk sdc at scsi3, channel 0, id 9, lun 0
Attached scsi generic sg4 at scsi3, channel 0, id 9, lun 0,  type 0
  Vendor: FUJITSU   Model: MAM3367MC         Rev: 0106
  Type:   Direct-Access                      ANSI SCSI revision: 03
SCSI device sdd: 71770599 512-byte hdwr sectors (36747 MB)
SCSI device sdd: drive cache: write back
 /dev/scsi/host3/bus0/target10/lun0: unknown partition table
Attached scsi disk sdd at scsi3, channel 0, id 10, lun 0
Attached scsi generic sg5 at scsi3, channel 0, id 10, lun 0,  type 0
  Vendor: FUJITSU   Model: MAM3367MC         Rev: 0106
  Type:   Direct-Access                      ANSI SCSI revision: 03
SCSI device sde: 71770599 512-byte hdwr sectors (36747 MB)
SCSI device sde: drive cache: write back
 /dev/scsi/host3/bus0/target11/lun0: unknown partition table
Attached scsi disk sde at scsi3, channel 0, id 11, lun 0
Attached scsi generic sg6 at scsi3, channel 0, id 11, lun 0,  type 0
     dpt_i2o: loaded successfully
pciehp: acpi_pciehprm:\_SB_.PCI0 evaluate _BBN fail=0x5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x5
modprobe: FATAL: Error inserting pciehp (/lib/modules/2.6.8-1-k7-smp/kernel/drivers/pci/hotplug/pciehp.ko): Operation not permitted

     pciehp: can't be loaded
missing kernel or user mode driver pciehp 
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
modprobe: FATAL: Error inserting shpchp (/lib/modules/2.6.8-1-k7-smp/kernel/drivers/pci/hotplug/shpchp.ko): Operation not permitted

     shpchp: can't be loaded
missing kernel or user mode driver shpchp 
pciehp: acpi_pciehprm:\_SB_.PCI0 evaluate _BBN fail=0x5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x5
modprobe: FATAL: Error inserting pciehp (/lib/modules/2.6.8-1-k7-smp/kernel/drivers/pci/hotplug/pciehp.ko): Operation not permitted

     pciehp: can't be loaded
missing kernel or user mode driver pciehp 
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
modprobe: FATAL: Error inserting shpchp (/lib/modules/2.6.8-1-k7-smp/kernel/drivers/pci/hotplug/shpchp.ko): Operation not permitted

     shpchp: can't be loaded
missing kernel or user mode driver shpchp 
     ignoring pci display device on 01:05.0
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ACPI: PCI interrupt 0000:03:00.0[D] -> GSI 19 (level, low) -> IRQ 193
ohci_hcd 0000:03:00.0: Advanced Micro Devices [AMD] AMD-768 [Opus] USB
ohci_hcd 0000:03:00.0: irq 193, pci mem f8ad9000
ohci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ACPI: PCI interrupt 0000:03:06.0[A] -> GSI 18 (level, low) -> IRQ 185
ohci_hcd 0000:03:06.0: NEC Corporation USB
ohci_hcd 0000:03:06.0: irq 185, pci mem f8adb000
ohci_hcd 0000:03:06.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ACPI: PCI interrupt 0000:03:06.1[B] -> GSI 19 (level, low) -> IRQ 193
ohci_hcd 0000:03:06.1: NEC Corporation USB (#2)
ohci_hcd 0000:03:06.1: irq 193, pci mem f8add000
ohci_hcd 0000:03:06.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
     ohci-hcd: loaded successfully
     aic7xxx: already loaded
     aic7xxx: already loaded
     aic7xxx: already loaded
     ohci-hcd: already loaded
     ohci-hcd: already loaded
ACPI: PCI interrupt 0000:03:06.2[C] -> GSI 16 (level, low) -> IRQ 201
ehci_hcd 0000:03:06.2: NEC Corporation USB 2.0
ehci_hcd 0000:03:06.2: irq 201, pci mem f8ae4000
ehci_hcd 0000:03:06.2: new USB bus registered, assigned bus number 4
ehci_hcd 0000:03:06.2: USB 2.0 enabled, EHCI 0.95, driver 2004-May-10
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 5 ports detected
     ehci-hcd: loaded successfully
     emu10k1: blacklisted
ACPI: PCI interrupt 0000:03:07.0[A] -> GSI 19 (level, low) -> IRQ 193
     snd-emu10k1: loaded successfully
gameport: pci0000:03:07.1 speed 917 kHz
     emu10k1-gp: loaded successfully
   pci      [success]
   usb     
   usb      [success]
done
Setting up IP spoofing protection: rp_filter.
Configuring network interfaces...Internet Software Consortium DHCP Client 2.0pl5
Copyright 1995, 1996, 1997, 1998, 1999 The Internet Software Consortium.
All rights reserved.

Please contribute if you find this software useful.
For info, please visit http://www.isc.org/dhcp-contrib.html

e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex
NET: Registered protocol family 17
Listening on LPF/eth0/00:02:b3:bf:4d:ef
Sending on   LPF/eth0/00:02:b3:bf:4d:ef
Sending on   Socket/fallback/fallback-net
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 4
DHCPOFFER from 192.168.0.1
DHCPREQUEST on eth0 to 255.255.255.255 port 67
DHCPACK from 192.168.0.1
bound to 192.168.0.11 -- renewal in 21600 seconds.
done.
Starting portmap daemon: portmap.
Starting portmapper...Mounting remote filesystems...
nfs warning: mount version older than kernel
nfs warning: mount version older than kernel
Loading the saved-state of the serial devices... 
/dev/ttyS0 at 0x03f8 (irq = 4) is a 16550A
/dev/ttyS1 at 0x02f8 (irq = 3) is a 16550A

Setting the System Clock using the Hardware Clock as reference...
System Clock set. Local time: Sun Sep 19 11:56:23 BST 2004

Initializing random number generator...done.
Recovering nvi editor sessions... done.
Setting up X server socket directory /tmp/.X11-unix...done.
Setting up ICE socket directory /tmp/.ICE-unix...done.
INIT: Entering runlevel: 2
Starting system log daemon: syslogd.
Starting kernel log daemon: klogd.
Starting domain name service:.
Starting portmap daemon: portmap.
Starting OpenLDAP: slapdNET: Registered protocol family 10
Disabled Privacy Extensions on device c0316d00(lo)
IPv6 over IPv4 tunneling driver
..
Loading ACPI modules:
    battery
    ac
    processor
ACPI: Processor [CPU0] (supports C1)
ACPI: Processor [CPU1] (supports C1)
    button
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (FF) [SLPF]
    fan
    thermal
Starting Advanced Configuration and Power Interface daemon: acpid.
Restoring ALSA mixer settings ... done.
Starting clamav virus database updater: freshclam.
Starting file alteration monitor: FAM.
Starting internet superserver: inetd.
Starting printer spooler: lpd.
Starting printer spooler: lpd already running.
Starting network benchmark server: netserver.
Exporting directories for NFS kernel daemon...Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
done.
Starting NFS kernel daemon: nfsd mountd.
Starting Name Service Cache Daemon: nscd.
Starting PCMCIA services: Linux Kernel Card Services
  options:  [pci] [cardbus] [pm]
cardmgr[2518]: no sockets found!
done.
Starting PostgreSQL database server: postmaster(FAILED)
ERROR: The database is in an older format that cannot be read by
version 7.4 of PostgreSQL.

Run postgresql-dump to dump the old database and to reload
it in the new format.
*** READ /usr/share/doc/postgresql/README.Debian.migration.gz FIRST! ***

The version 7.4 postmaster cannot be started until
this is done.
Starting System status server: rwhod.
Starting disk monitoring daemon: smartd.
Starting network management services: snmpd.
Starting OpenBSD Secure Shell server: sshd.
Not starting udftools packet writing: No devices listed in /etc/default/udftools
Starting webmin: webmin.
Setting up X font server socket directory /tmp/.font-unix...done.
Starting X font server: xfs.
Starting Xprint servers: Xprt.
Starting NFS common utilities: statd.
Starting NTP server: ntpd.
Starting RAID monitor daemon: mdadm -F.
ProFTPd is started from inetd/xinetd.
Starting /usr/sbin/snmptrapfmt...
Starting deferred execution scheduler: atd.
Starting periodic command scheduler: cron.
Starting web server: apache.
ERROR: Module ide_cd does not exist in /proc/modules
Not starting GNOME Display Manager (gdm); it is not the default display manager.
Starting K Desktop Manager: kdm.
Not starting X display manager (xdm); it is not the default display manager.
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.

Debian GNU/Linux 3.1 steely ttyS0

steely login: root
Password: 
Last login: Sun Sep 19 11:44:41 2004 on ttyS0
Linux steely 2.6.8-1-k7-smp #1 SMP Tue Sep 14 00:50:03 EDT 2004 i686 GNU/Linux
steely:~# cat /proc/mdstat 
Personalities : 
unused devices: <none>
steely:~# mdadm --create /dev/md0 -l 0 -n 2 /dev/sdb /dev/sdc
mdadm: /dev/sdb appears to be part of a raid array:
    level=1 devices=2 ctime=Sun Sep 19 11:45:19 2004
mdadm: /dev/sdc appears to be part of a raid array:
    level=1 devices=2 ctime=Sun Sep 19 11:45:19 2004
Continue creating array? y
md: bind<sdb>
md: bind<sdc>
md: raid0 personality registered as nr 2
md0: setting max_sectors to 128, segment boundary to 32767
raid0: looking at sdc
raid0:   comparing sdc(35885184) with sdc(35885184)
raid0:   END
raid0:   ==> UNIQUE
raid0: 1 zones
raid0: looking at sdb
raid0:   comparing sdb(35885184) with sdc(35885184)
raid0:   EQUAL
raid0: FINAL 1 zones
raid0: done.
raid0 : md_size is 71770368 blocks.
raid0 : conf->hash_spacing is 71770368 blocks.
raid0 : nb_zone is 1.
raid0 : Allocating 4 bytes for hash.
mdadm: array /dev/md0 started.
steely:~# mkfs.xfs /dev/md0
mkfs.xfs: /dev/md0 appears to contain an existing filesystem (xfs).
mkfs.xfs: Use the -f option to force overwrite.
steely:~# mkfs.xfs -f /dev/md0
meta-data=/dev/md0               isize=256    agcount=16, agsize=1121424 blks
         =                       sectsz=512  
data     =                       bsize=4096   blocks=17942592, imaxpct=25
         =                       sunit=16     swidth=32 blks, unwritten=1
naming   =version 2              bsize=4096  
log      =internal log           bsize=4096   blocks=8768, version=1
         =                       sectsz=512   sunit=0 blks
realtime =none                   extsz=131072 blocks=0, rtextents=0
steely:~# mount /dev/md0 /raid
XFS mounting filesystem md0
steely:~# cd /raid
steely:/raid# tiobench
No size specified, using 1792 MB
Run #1: /usr/bin/tiotest -t 1 -f 1792 -r 4000 -b 4096 -d . -Tbad: scheduling while atomic!
 [<c02979bf>] schedule+0x7ff/0x810
 [<c02980eb>] schedule_timeout+0x6b/0xc0
 [<c0129b50>] process_timeout+0x0/0x10
 [<f8b00894>] adpt_i2o_post_this+0x54/0xb0 [dpt_i2o]
 [<f8b02069>] adpt_scsi_to_i2o+0x219/0x2c0 [dpt_i2o]
 [<f8aff580>] adpt_queue+0xb0/0x120 [dpt_i2o]
 [<f883d938>] scsi_dispatch_cmd+0x1b8/0x2a0 [scsi_mod]
 [<f883dba0>] scsi_done+0x0/0x30 [scsi_mod]
 [<f88404a0>] scsi_times_out+0x0/0xc0 [scsi_mod]
 [<f8843af9>] scsi_request_fn+0x219/0x4a0 [scsi_mod]
 [<c0140b73>] mempool_free+0x63/0xd0
 [<c020bc10>] blk_run_queue+0x40/0x80
 [<f8842c66>] scsi_run_queue+0xa6/0x110 [scsi_mod]
 [<f8842e96>] scsi_end_request+0xe6/0x110 [scsi_mod]
 [<f8843204>] scsi_io_completion+0x184/0x530 [scsi_mod]
 [<f8835bc9>] sd_rw_intr+0x89/0x330 [sd_mod]
 [<f883ddf5>] scsi_finish_command+0x85/0xe0 [scsi_mod]
 [<f883dcf7>] scsi_softirq+0xb7/0xe0 [scsi_mod]
 [<c0125126>] __do_softirq+0xa6/0xb0
 [<c012515d>] do_softirq+0x2d/0x30
 [<c0108af8>] do_IRQ+0x138/0x190
 [<c0106c30>] common_interrupt+0x18/0x20
 [<c0104030>] default_idle+0x0/0x40
 [<c010405c>] default_idle+0x2c/0x40
 [<c01040e3>] cpu_idle+0x33/0x40
 [<c035e940>] start_kernel+0x1c0/0x220
 [<c035e370>] unknown_bootoption+0x0/0x160
Unable to handle kernel NULL pointer dereference at virtual address 00000000
 printing eip:
c0119dd6
*pde = 00000000
Oops: 0002 [#1]
PREEMPT SMP 
Modules linked in: raid0 ide_scsi ds yenta_socket pcmcia_core nfsd exportfs thermal fan button processor ac battery ipv6 nfs lockd sunrpc af_packet emu10k1_gp gameport snd_emu10k1 snd_rawmidi snd_pcm_oss snd_mixer_oss snd_pcm snd_timer snd_seq_device snd_ac97_codec snd_page_alloc snd_util_mem snd_hwdep snd soundcore ehci_hcd ohci_hcd usbcore dpt_i2o hw_random amd74xx ide_core pci_hotplug amd_k7_agp agpgart floppy tsdev mousedev parport_pc parport psmouse pcspkr rtc evdev md dm_mod capability commoncap e1000 xfs ext3 jbd mbcache sd_mod sg unix font vesafb cfbcopyarea cfbimgblt cfbfillrect aic7xxx scsi_mod
CPU:    0
EIP:    0060:[<c0119dd6>]    Not tainted
EFLAGS: 00010086   (2.6.8-1-k7-smp) 
EIP is at dequeue_task+0x16/0x50
eax: 00000000   ebx: c02d21a0   ecx: c02d2330   edx: c02d2180
esi: 00000000   edi: c035c000   ebp: c035dadc   esp: c035dad4
ds: 007b   es: 007b   ss: 0068
Process swapper (pid: 0, threadinfo=c035c000 task=c02d2180)
Stack: c02d2180 c035db64 c035daf0 c011a0f8 c02d2180 00000000 c02d2180 c035db50 
       c02972e0 c02d2180 c180bce0 00000000 00000000 00000000 00000000 00000000 
       00000000 00000000 c180bce0 00000000 0b626dc0 c94eb540 000f422d 00000046 
Call Trace:
 [<c011a0f8>] deactivate_task+0x28/0x40
 [<c02972e0>] schedule+0x120/0x810
 [<c02980eb>] schedule_timeout+0x6b/0xc0
 [<c0129b50>] process_timeout+0x0/0x10
 [<f8b00894>] adpt_i2o_post_this+0x54/0xb0 [dpt_i2o]
 [<f8b02069>] adpt_scsi_to_i2o+0x219/0x2c0 [dpt_i2o]
 [<f8aff580>] adpt_queue+0xb0/0x120 [dpt_i2o]
 [<f883d938>] scsi_dispatch_cmd+0x1b8/0x2a0 [scsi_mod]
 [<f883dba0>] scsi_done+0x0/0x30 [scsi_mod]
 [<f88404a0>] scsi_times_out+0x0/0xc0 [scsi_mod]
 [<f8843af9>] scsi_request_fn+0x219/0x4a0 [scsi_mod]
 [<c0140b73>] mempool_free+0x63/0xd0
 [<c020bc10>] blk_run_queue+0x40/0x80
 [<f8842c66>] scsi_run_queue+0xa6/0x110 [scsi_mod]
 [<f8842e96>] scsi_end_request+0xe6/0x110 [scsi_mod]
 [<f8843204>] scsi_io_completion+0x184/0x530 [scsi_mod]
 [<f8835bc9>] sd_rw_intr+0x89/0x330 [sd_mod]
 [<f883ddf5>] scsi_finish_command+0x85/0xe0 [scsi_mod]
 [<f883dcf7>] scsi_softirq+0xb7/0xe0 [scsi_mod]
 [<c0125126>] __do_softirq+0xa6/0xb0
 [<c012515d>] do_softirq+0x2d/0x30
 [<c0108af8>] do_IRQ+0x138/0x190
 [<c0106c30>] common_interrupt+0x18/0x20
 [<c0104030>] default_idle+0x0/0x40
 [<c010405c>] default_idle+0x2c/0x40
 [<c01040e3>] cpu_idle+0x33/0x40
 [<c035e940>] start_kernel+0x1c0/0x220
 [<c035e370>] unknown_bootoption+0x0/0x160
Code: ff 0e 8b 42 20 8b 4b 04 89 01 89 48 04 c7 42 20 00 01 10 00 
 

--- End Message ---
--- Begin Message ---
The mail address of the submitter bounces, closing the bug.

Cheers,
        Moritz


--- End Message ---

Reply to: