Bug#348492: marked as done (Serverworks CSB6 vs. kernel 2.6.12-10)
Your message dated Sat, 29 Nov 2008 17:21:13 +0100
with message-id <20081129162113.GA6706@galadriel.inutil.org>
and subject line Re: Serverworks CSB6 vs. kernel 2.6.12-10
has caused the Debian Bug report #348492,
regarding Serverworks CSB6 vs. kernel 2.6.12-10
to be marked as done.
This means that you claim that the problem has been dealt with.
If this is not the case it is now your responsibility to reopen the
Bug report if necessary, and/or fix the problem forthwith.
(NB: If you are a system administrator and have no idea what this
message is talking about, this may indicate a serious mail system
misconfiguration somewhere. Please contact owner@bugs.debian.org
immediately.)
--
348492: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=348492
Debian Bug Tracking System
Contact owner@bugs.debian.org with problems
--- Begin Message ---
Package: linux-source-2.6.12
Version: 2.6.12-10
I'm using Fujitsu-Siemens TX200 (one HT proc) machine with Serverworks
CSB6 ide controler.
System is setup on SCSI disk so I have some possibilities to experiment.
lspci -vvv
[...]
0000:00:0f.1 IDE interface: ServerWorks CSB6 RAID/IDE Controller (rev
a0) (prog-if 8a [Master SecP PriP])
Subsystem: Unknown device 1734:1012
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 0x10 (64 bytes)
Region 0: I/O ports at <ignored>
Region 1: I/O ports at <ignored>
Region 2: I/O ports at <ignored>
Region 3: I/O ports at <ignored>
Region 4: I/O ports at 1400 [size=16]
[...]
System is Sarge but I've installed package in question
(linux-source-2.6.12) from testing.
Debian-way custom compilation (make-kpkg) with predefined (nothing
changed) config is smooth,
but I cannot make serverworks module run.
modprobe serverworks loads without error and I can see it listed with lsmod.
But there is no :
SvrWks CSB6: IDE controller at PCI slot 0000:00:0f.1
SvrWks CSB6: chipset revision 160
[...] in dmesg after module load, and I cannot access ide disks.
No such problem with stock kernel (linux-2.6.12.6.tar.bz2) compiled
debian-way with predefined config.
(module loads, I can see /dev/hda)
My idea is that there has to be something wrong with debian/ide patches.
Additional info:
- I'm not loading ide-generic module at all.
- lsmod for not-working and working kernels gives same modules list:
Though I'm no kernel hacker, I have some time and cpu cycles, so let me
know if I could help somehow solve this
rgrds.,
Konrad Korzeniowski
--- End Message ---
--- Begin Message ---
Version: 2.6.18.dfsg.1-12
On Sat, Nov 29, 2008 at 11:34:48AM +0100, Konrad Korzeniowski wrote:
>
> [2008-11-28 23:51] Moritz Muehlenhoff:
> > On Tue, Jan 17, 2006 at 11:25:23AM +0100, Konrad Korzeniowski wrote:
> >
> >> Package: linux-source-2.6.12
> >> Version: 2.6.12-10
> >>
> > Does this error still occur with more recent kernel versions?
> >
> > Cheers,
> > Moritz
> >
> Hi,
>
> right now on these machines is installed Etch with kernel 2.6.18 (
> -vserver) from distribution
> and I'm almost sure it runs without problems.
Ok, marking this version as closed.
Cheers,
Moritz
--- End Message ---
Reply to: