Bug#497873: linux-image-2.6.26-1-686: Please enable prism54 module
Subject: linux-image-2.6.26-1-686: Please enable prism54 module
Package: linux-image-2.6.26-1-686
Version: 2.6.26-4
Severity: normal
Tags: patch
*** Please type your report below this line ***
Hi, I own a prism pcmcia wifi card that is the main internet interface
of my computer. Since some version of the kernel, the prism54 is no
longer enabled and is replaced with p54. The problem is that p54 woks
very badly with my hardware (difficulties to find AP, connection losts,
etc.). With the prism54 module I did not encounter these problems.
My card is:
07:00.0 Network controller [0280]: Intersil Corporation ISL3890 [Prism
GT/Prism Duette]/ISL3886 [Prism Javelin/Prism Xbow] [1260:3890] (rev
01)
Here the patch I used to enable PRISM54 on my computer:
--- /boot/config-2.6.26-1-686 2008-08-28 12:28:24.000000000 -0400
+++ linux-source-2.6.26/.config 2008-09-04 06:35:01.000000000 -0400
@@ -1861,7 +1861,7 @@ CONFIG_PCMCIA_ATMEL=m
CONFIG_USB_ATMEL=m
CONFIG_AIRO_CS=m
CONFIG_PCMCIA_WL3501=m
-# CONFIG_PRISM54 is not set
+CONFIG_PRISM54=m
CONFIG_USB_ZD1201=m
CONFIG_USB_NET_RNDIS_WLAN=m
CONFIG_RTL8180=m
-- Package-specific info:
** Version:
Linux version 2.6.26-1-686 (Debian 2.6.26-4) (waldi@debian.org) (gcc
version 4.1.3 20080623 (prerelease) (Debian 4.1.2-23)) #1 SMP Thu Aug
28 12:00:54 UTC 2008
** Command line:
root=/dev/hda2 ro quiet
** Not tainted
** Kernel log:
[ 20.989806] ACPI: PCI Interrupt 0000:02:03.0[A] -> Link [LNKB] ->
GSI 5 (level, low) -> IRQ 5
[ 20.989824] firmware: requesting ess/maestro3_assp_kernel.fw
[ 21.804771] parport_pc 00:0f: reported by Plug and Play ACPI
[ 21.804835] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[ 21.864288] NET: Registered protocol family 23
[ 21.932418] found SMC SuperIO Chip (devid=0x0e rev=01 base=0x002e): LPC47N252
[ 21.932446] smsc_ircc_present: can't get sir_base of 0x2f8
[ 22.784343] firmware: requesting ess/maestro3_assp_minisrc.fw
[ 22.842230] IBM TrackPoint firmware: 0x0b, buttons: 2/3
[ 23.065209] input: TPPS/2 IBM TrackPoint as /class/input/input8
[ 24.065178] Yenta: CardBus bridge found at 0000:02:0f.0 [1028:00a3]
[ 24.065216] PCI: Bus 3, cardbus bridge: 0000:02:0f.0
[ 24.065222] IO window: 0x0000e000-0x0000e0ff
[ 24.065230] IO window: 0x00001000-0x000010ff
[ 24.065238] PREFETCH window: 0x20020000-0x2003ffff
[ 24.065246] MEM window: 0xf4000000-0xf7ffffff
[ 24.065258] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 24.065264] Yenta: Routing CardBus interrupts to PCI
[ 24.065273] Yenta TI: socket 0000:02:0f.0, mfunc 0x05033002, devctl 0x64
[ 24.296414] Yenta: ISA IRQ mask 0x0818, PCI irq 10
[ 24.296424] Socket status: 30000006
[ 24.296433] pcmcia: parent PCI bridge I/O window: 0xe000 - 0xffff
[ 24.296441] cs: IO port probe 0xe000-0xffff: clean.
[ 24.297562] pcmcia: parent PCI bridge Memory window: 0xf4000000 - 0xfbffffff
[ 24.297570] pcmcia: parent PCI bridge Memory window: 0x20000000 - 0x200fffff
[ 24.298027] Yenta: CardBus bridge found at 0000:02:0f.1 [1028:00a3]
[ 24.298055] PCI: Bus 7, cardbus bridge: 0000:02:0f.1
[ 24.298061] IO window: 0x00001400-0x000014ff
[ 24.298069] IO window: 0x00001800-0x000018ff
[ 24.298077] PREFETCH window: 0x20040000-0x2005ffff
[ 24.298086] MEM window: 0x24000000-0x27ffffff
[ 24.298097] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 24.298103] Yenta: Routing CardBus interrupts to PCI
[ 24.298112] Yenta TI: socket 0000:02:0f.1, mfunc 0x05033002, devctl 0x64
[ 24.528454] Yenta: ISA IRQ mask 0x0818, PCI irq 10
[ 24.528465] Socket status: 30000020
[ 24.528474] pcmcia: parent PCI bridge I/O window: 0xe000 - 0xffff
[ 24.528482] cs: IO port probe 0xe000-0xffff: clean.
[ 24.529604] pcmcia: parent PCI bridge Memory window: 0xf4000000 - 0xfbffffff
[ 24.529611] pcmcia: parent PCI bridge Memory window: 0x20000000 - 0x200fffff
[ 25.168054] pccard: CardBus card inserted into slot 1
[ 25.314430] cs: IO port probe 0x100-0x3af: excluding 0x200-0x207 0x280-0x287
[ 25.315465] cs: IO port probe 0x3e0-0x4ff: clean.
[ 25.315925] cs: IO port probe 0x820-0x8ff: clean.
[ 25.316046] cs: IO port probe 0xc00-0xcf7: clean.
[ 25.316648] cs: IO port probe 0xa00-0xaff: clean.
[ 25.318467] cs: IO port probe 0x100-0x3af: excluding 0x200-0x207 0x280-0x287
[ 25.319504] cs: IO port probe 0x3e0-0x4ff: clean.
[ 25.319964] cs: IO port probe 0x820-0x8ff: clean.
[ 25.320102] cs: IO port probe 0xc00-0xcf7: clean.
[ 25.320704] cs: IO port probe 0xa00-0xaff: clean.
[ 25.424063] prism54: no symbol version for struct_module
[ 25.622638] prism54pci 0000:07:00.0: enabling device (0000 -> 0002)
[ 25.622662] ACPI: PCI Interrupt 0000:07:00.0[A] -> Link [LNKD] ->
GSI 10 (level, low) -> IRQ 10
[ 25.622688] PCI: Setting latency timer of device 0000:07:00.0 to 64
[ 25.672459] firmware: requesting isl3886
[ 25.722864] p54: LM86 firmware
[ 25.722876] p54: FW rev 2.7.0.0 - Softmac protocol 4.1
[ 26.643307] p54: unknown eeprom code : 0x1
[ 26.643307] p54: unknown eeprom code : 0x3
[ 26.643307] p54: unknown eeprom code : 0x1007
[ 26.643307] p54: unknown eeprom code : 0x1008
[ 26.643307] p54: unknown eeprom code : 0x1100
[ 26.643307] p54: unknown eeprom code : 0x1905
[ 26.645169] phy0: Selected rate control algorithm 'pid'
[ 26.975932] phy0: hwaddr 00:00:48:25:80:cd, isl3880
[ 28.705780] Adding 232932k swap on /dev/hda3. Priority:-1
extents:1 across:232932k
[ 29.211344] EXT3 FS on hda2, internal journal
[ 29.917367] loop: module loaded
[ 30.194567] Dell laptop SMM driver v1.14 21/02/2005 Massimo Dal
Zotto (dz@debian.org)
[ 35.204030] cpufreq: change to state 1 failed with new_state 2 and result 0
[ 35.204030] cpufreq: change to state 0 failed with new_state 2 and result 0
[ 45.546328] NET: Registered protocol family 10
[ 45.547710] lo: Disabled Privacy Extensions
[ 46.422480] lp0: using parport0 (interrupt-driven).
[ 46.489788] ppdev: user-space parallel port driver
[ 49.890365] warning: `avahi-daemon' uses 32-bit capabilities
(legacy support in use)
[ 63.386701] [drm] Initialized drm 1.1.0 20060810
[ 63.417805] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
[ 63.417824] PCI: setting IRQ 11 as level-triggered
[ 63.417832] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] ->
GSI 11 (level, low) -> IRQ 11
[ 63.418280] [drm] Initialized r128 2.5.0 20030725 on minor 0
[ 63.423536] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[ 63.423586] agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
[ 63.423612] agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
[ 187.496341] Loaded prism54 driver, version 1.2
[ 202.286234] Unloaded prism54 driver
[ 265.252375] ACPI: PCI interrupt for device 0000:07:00.0 disabled
[ 271.356533] Loaded prism54 driver, version 1.2
[ 271.356639] ACPI: PCI Interrupt 0000:07:00.0[A] -> Link [LNKD] ->
GSI 10 (level, low) -> IRQ 10
[ 271.378919] udev: renamed network interface eth0 to eth2
[ 312.560995] eth2: resetting device...
[ 312.561033] eth2: uploading firmware...
[ 312.610742] firmware: requesting isl3890
[ 312.729799] eth2: firmware version: 1.0.4.3
[ 312.729886] eth2: firmware upload complete
[ 313.006373] eth2: interface reset complete
[ 313.007011] ADDRCONF(NETDEV_UP): eth2: link is not ready
[ 315.662740] ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready
[ 326.080031] eth2: no IPv6 routers present
** Loaded modules:
Module Size Used by
prism54 44680 0
r128 32288 2
drm 65256 3 r128
ppdev 6468 0
lp 8164 0
ipv6 235204 14
speedstep_lib 4516 0
cpufreq_userspace 3172 0
cpufreq_stats 3776 0
cpufreq_powersave 1856 0
cpufreq_ondemand 6476 0
freq_table 4224 2 cpufreq_stats,cpufreq_ondemand
cpufreq_conservative 5960 0
i8k 5144 0
sbp2 18572 0
loop 12748 0
arc4 1824 0
ecb 2624 0
crypto_blkcipher 15236 1 ecb
mac80211 139680 0
cfg80211 21576 1 mac80211
pcmcia 29548 0
joydev 8480 0
irda 95480 0
parport_pc 22500 1
parport 30988 3 ppdev,lp,parport_pc
crc_ccitt 2080 1 irda
yenta_socket 20620 3
rsrc_nonstatic 9504 1 yenta_socket
pcmcia_core 31892 3 pcmcia,yenta_socket,rsrc_nonstatic
snd_maestro3 16100 5
firmware_class 6816 3 prism54,pcmcia,snd_maestro3
snd_ac97_codec 88484 1 snd_maestro3
button 6064 0
ac97_bus 1728 1 snd_ac97_codec
video 16400 0
output 2912 1 video
snd_pcsp 8576 0
snd_pcm_oss 32800 0
snd_mixer_oss 12320 2 snd_pcm_oss
snd_pcm 62628 5 snd_maestro3,snd_ac97_codec,snd_pcsp,snd_pcm_oss
snd_timer 17800 2 snd_pcm
battery 10180 0
ac 4196 0
psmouse 32336 0
snd 45604 13
snd_maestro3,snd_ac97_codec,snd_pcsp,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
serio_raw 4740 0
soundcore 6368 2 snd
snd_page_alloc 7816 1 snd_pcm
intel_rng 4576 0
rng_core 3940 1 intel_rng
intel_agp 22300 1
agpgart 28776 2 drm,intel_agp
iTCO_wdt 9508 0
shpchp 25528 0
pci_hotplug 23460 1 shpchp
evdev 8000 6
dcdbas 6272 0
ext3 105256 1
jbd 39444 1 ext3
mbcache 7108 1 ext3
usbhid 35904 0
hid 33184 1 usbhid
ff_memless 4392 1 usbhid
ide_cd_mod 27652 0
cdrom 30176 1 ide_cd_mod
ide_disk 10496 3
ata_generic 4676 0
libata 140416 1 ata_generic
scsi_mod 129356 2 sbp2,libata
floppy 47716 0
ohci1394 24944 0
ieee1394 75800 2 sbp2,ohci1394
3c59x 35624 0
mii 4896 1 3c59x
dock 8272 1 libata
uhci_hcd 18672 0
usbcore 118160 3 usbhid,uhci_hcd
piix 6568 0 [permanent]
ide_pci_generic 3908 0 [permanent]
ide_core 92628 4 ide_cd_mod,ide_disk,piix,ide_pci_generic
thermal 15228 0
processor 32576 2 thermal
fan 4164 0
thermal_sys 10856 4 video,thermal,processor,fan
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82815 815 Chipset Host
Bridge and Memory Controller Hub [8086:1130] (rev 02)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at e4000000 (32-bit, prefetchable) [size=64M]
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
Kernel modules: intel-agp
00:01.0 PCI bridge [0604]: Intel Corporation 82815 815 Chipset AGP
Bridge [8086:1131] (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fc000000-fdffffff
Prefetchable memory behind bridge: e8000000-ebffffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR+
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Kernel modules: shpchp
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge
[8086:2448] (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=10, sec-latency=32
I/O behind bridge: 0000e000-0000ffff
Memory behind bridge: f4000000-fbffffff
Prefetchable memory behind bridge: 20000000-200fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Kernel modules: shpchp
00:1f.0 ISA bridge [0601]: Intel Corporation 82801BAM ISA Bridge (LPC)
[8086:244c] (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Kernel modules: intel-rng, iTCO_wdt
00:1f.1 IDE interface [0101]: Intel Corporation 82801BAM IDE U100
Controller [8086:244a] (rev 02) (prog-if 80 [Master])
Subsystem: Intel Corporation Device [8086:4541]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
[disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
[disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
[disabled] [size=1]
Region 4: I/O ports at bfa0 [size=16]
Kernel driver in use: PIIX_IDE
Kernel modules: piix
00:1f.2 USB Controller [0c03]: Intel Corporation 82801BA/BAM USB
Controller #1 [8086:2442] (rev 02)
Subsystem: Intel Corporation Device [8086:4541]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 10
Region 4: I/O ports at dce0 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
01:00.0 VGA compatible controller [0300]: ATI Technologies Inc Rage
Mobility M4 AGP [1002:4d46]
Subsystem: Dell Device [1028:00a3]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr-
Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e8000000 (32-bit, prefetchable) [size=64M]
Region 1: I/O ports at cc00 [size=256]
Region 2: Memory at fcffc000 (32-bit, non-prefetchable) [size=16K]
[virtual] Expansion ROM at fc000000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel modules: aty128fb
02:03.0 Multimedia audio controller [0401]: ESS Technology ES1983S
Maestro-3i PCI Audio Accelerator [125d:1998] (rev 10)
Subsystem: Dell Device [1028:00a3]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (500ns min, 6000ns max)
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at ec00 [size=256]
Region 1: Memory at f8ffe000 (32-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: Maestro3
Kernel modules: snd-maestro3
02:06.0 Ethernet controller [0200]: 3Com Corporation 3c556 Hurricane
CardBus [Cyclone] [10b7:6055] (rev 10)
Subsystem: 3Com Corporation Device [10b7:6456]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (2500ns min, 1250ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at e800 [size=256]
Region 1: Memory at f8ffdc00 (32-bit, non-prefetchable) [size=128]
Region 2: Memory at f8ffd800 (32-bit, non-prefetchable) [size=128]
Expansion ROM at 20000000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: 3c59x
Kernel modules: 3c59x
02:06.1 Communication controller [0780]: 3Com Corporation Mini PCI 56k
Winmodem [10b7:1007] (rev 10)
Subsystem: 3Com Corporation Device [10b7:615b]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (2500ns min, 1250ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at e400 [size=256]
Region 1: Memory at f8ffd400 (32-bit, non-prefetchable) [size=256]
Region 2: Memory at f8ffd000 (32-bit, non-prefetchable) [size=128]
Capabilities: <access denied>
02:0f.0 CardBus bridge [0607]: Texas Instruments PCI4451 PC card
Cardbus Controller [104c:ac42]
Subsystem: Dell Device [1028:00a3]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f8000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
Memory window 0: 20020000-2003f000 (prefetchable)
Memory window 1: f4000000-f7fff000
I/O window 0: 0000e000-0000e0ff
I/O window 1: 00001000-000010ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
Kernel modules: yenta_socket
02:0f.1 CardBus bridge [0607]: Texas Instruments PCI4451 PC card
Cardbus Controller [104c:ac42]
Subsystem: Dell Device [1028:00a3]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f8001000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=07, subordinate=0a, sec-latency=176
Memory window 0: 20040000-2005f000 (prefetchable)
Memory window 1: 24000000-27fff000
I/O window 0: 00001400-000014ff
I/O window 1: 00001800-000018ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
Kernel modules: yenta_socket
02:0f.2 FireWire (IEEE 1394) [0c00]: Texas Instruments PCI4451
IEEE-1394 Controller [104c:8027] (prog-if 10)
Subsystem: Dell Device [1028:00a3]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (500ns min, 1000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f8ffc800 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at f8ff8000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: ohci1394
Kernel modules: ohci1394
07:00.0 Network controller [0280]: Intersil Corporation ISL3890 [Prism
GT/Prism Duette]/ISL3886 [Prism Javelin/Prism Xbow] [1260:3890] (rev 01)
Subsystem: Accton Technology Corporation Device [1113:a301]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 64 (2500ns min, 7000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at 24000000 (32-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: prism54
Kernel modules: p54pci, prism54
-- System Information:
Debian Release: lenny/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: i386 (i686)
Kernel: Linux 2.6.26-1-686 (SMP w/1 CPU core)
Locale: LANG=fr_FR.UTF-8, LC_CTYPE=fr_FR.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.26-1-686 depends on:
ii debconf [debconf-2.0] 1.5.22 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92f tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.26-1-686 recommends:
ii libc6-i686 2.7-13 GNU C Library: Shared libraries [i
Versions of packages linux-image-2.6.26-1-686 suggests:
ii grub 0.97-47 GRand Unified Bootloader (Legacy v
pn linux-doc-2.6.26 <none> (no description available)
-- debconf information:
linux-image-2.6.26-1-686/preinst/abort-overwrite-2.6.26-1-686:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.26-1-686/postinst/bootloader-error-2.6.26-1-686:
linux-image-2.6.26-1-686/postinst/depmod-error-initrd-2.6.26-1-686: false
linux-image-2.6.26-1-686/prerm/removing-running-kernel-2.6.26-1-686: true
linux-image-2.6.26-1-686/postinst/old-system-map-link-2.6.26-1-686: true
linux-image-2.6.26-1-686/preinst/abort-install-2.6.26-1-686:
linux-image-2.6.26-1-686/preinst/lilo-has-ramdisk:
linux-image-2.6.26-1-686/preinst/bootloader-initrd-2.6.26-1-686: true
linux-image-2.6.26-1-686/prerm/would-invalidate-boot-loader-2.6.26-1-686: true
linux-image-2.6.26-1-686/preinst/elilo-initrd-2.6.26-1-686: true
linux-image-2.6.26-1-686/postinst/kimage-is-a-directory:
linux-image-2.6.26-1-686/postinst/old-dir-initrd-link-2.6.26-1-686: true
linux-image-2.6.26-1-686/postinst/create-kimage-link-2.6.26-1-686: true
linux-image-2.6.26-1-686/preinst/lilo-initrd-2.6.26-1-686: true
linux-image-2.6.26-1-686/postinst/old-initrd-link-2.6.26-1-686: true
linux-image-2.6.26-1-686/preinst/overwriting-modules-2.6.26-1-686: true
linux-image-2.6.26-1-686/postinst/depmod-error-2.6.26-1-686: false
linux-image-2.6.26-1-686/postinst/bootloader-test-error-2.6.26-1-686:
linux-image-2.6.26-1-686/preinst/failed-to-move-modules-2.6.26-1-686:
linux-image-2.6.26-1-686/preinst/initrd-2.6.26-1-686:
Reply to: