Bug#494036: linux-image-2.6.26-1-686: hwclock freezes the machine
Hi Bastian,
Today, I successed to reproduct the bug with 2.6.25-1-686 and 2.6.25-2-686
after some try. 2.6.26-1-686 freeze just more quickly.
2.6.24-1-262 react differently when I try to stress it with hwclock. It gives
me this message instead of the freeze:
select() to /dev/rtc to wait for clock tick timed out
I attached the dmesg output.
Cheers,
Gonéri
lity grouping on. Total pages: 518114
[ 0.000000] Kernel command line: root=/dev/sda1 ro
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 1729.075 MHz processor.
[ 0.004000] Console: colour VGA+ 80x25
[ 0.004000] console [tty0] enabled
[ 0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.004000] Memory: 2061700k/2088772k available (1727k kernel code, 25768k reserved, 717k data, 244k init, 1171268k highmem)
[ 0.004000] virtual kernel memory layout:
[ 0.004000] fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB)
[ 0.004000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.004000] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 0.004000] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 0.004000] .init : 0xc036b000 - 0xc03a8000 ( 244 kB)
[ 0.004000] .data : 0xc02aff97 - 0xc0363560 ( 717 kB)
[ 0.004000] .text : 0xc0100000 - 0xc02aff97 (1727 kB)
[ 0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.084009] Calibrating delay using timer specific routine.. 3462.09 BogoMIPS (lpj=6924192)
[ 0.084165] Security Framework initialized
[ 0.084225] SELinux: Disabled at boot.
[ 0.084282] Capability LSM initialized
[ 0.084352] Mount-cache hash table entries: 512
[ 0.084573] Initializing cgroup subsys ns
[ 0.084632] Initializing cgroup subsys cpuacct
[ 0.084708] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.084796] CPU: L2 cache: 2048K
[ 0.084852] Intel machine check architecture supported.
[ 0.084912] Intel machine check reporting enabled on CPU#0.
[ 0.084974] Compat vDSO mapped to ffffe000.
[ 0.085035] Checking 'hlt' instruction... OK.
[ 0.100348] SMP alternatives: switching to UP code
[ 0.102442] Freeing SMP alternatives: 16k freed
[ 0.102498] ACPI: Core revision 20070126
[ 0.112054] CPU0: Intel(R) Pentium(R) M processor 1.73GHz stepping 08
[ 0.112196] Total of 1 processors activated (3462.09 BogoMIPS).
[ 0.112444] ENABLING IO-APIC IRQs
[ 0.112691] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.156009] Brought up 1 CPUs
[ 0.156009] CPU0 attaching sched-domain:
[ 0.156009] domain 0: span 01
[ 0.156009] groups: 01
[ 0.156009] net_namespace: 548 bytes
[ 0.156009] Booting paravirtualized kernel on bare hardware
[ 0.156009] NET: Registered protocol family 16
[ 0.156009] ACPI: bus type pci registered
[ 0.156009] PCI: Using MMCONFIG for extended config space
[ 0.156009] PCI: Using configuration type 1
[ 0.156009] Setting up standard PCI resources
[ 0.156010] ACPI: EC: Look up EC in DSDT
[ 0.169909] ACPI: SSDT 7F7D1FD0, 0043 (r1 LMPWR DELLLOM 1001 INTL 20030522)
[ 0.170172] ACPI: Interpreter enabled
[ 0.170227] ACPI: (supports S0 S3 S4 S5)
[ 0.170413] ACPI: Using IOAPIC for interrupt routing
[ 0.202035] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.204728] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
[ 0.204735] pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
[ 0.204816] pci 0000:00:1f.0: quirk: region 1080-10bf claimed by ICH6 GPIO
[ 0.205382] PCI: Transparent bridge - 0000:00:1e.0
[ 0.205486] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.205950] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT]
[ 0.225568] ACPI: PCI Interrupt Link [LNKA] (IRQs 9 10 *11)
[ 0.225899] ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7) *10
[ 0.226233] ACPI: PCI Interrupt Link [LNKC] (IRQs *9 10 11)
[ 0.226566] ACPI: PCI Interrupt Link [LNKD] (IRQs *5 7 9 10 11)
[ 0.226941] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.227580] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.228200] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.228918] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.229004] pnp: PnP ACPI init
[ 0.229061] ACPI: bus type pnp registered
[ 0.289323] pnpacpi: exceeded the max number of IO resources: 40
[ 0.290160] pnp: PnP ACPI: found 15 devices
[ 0.290216] ACPI: ACPI bus type pnp unregistered
[ 0.290275] PnPBIOS: Disabled by ACPI PNP
[ 0.290536] PCI: Using ACPI for IRQ routing
[ 0.290593] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 0.290926] hpet clockevent registered
[ 0.290933] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.291112] hpet0: 3 64-bit timers, 14318180 Hz
[ 0.292077] system 00:00: iomem range 0x0-0x9fbff could not be reserved
[ 0.292140] system 00:00: iomem range 0x9fc00-0x9ffff could not be reserved
[ 0.292203] system 00:00: iomem range 0xc0000-0xcffff could not be reserved
[ 0.292266] system 00:00: iomem range 0xe0000-0xfffff could not be reserved
[ 0.292328] system 00:00: iomem range 0x100000-0x7f7d17ff could not be reserved
[ 0.292407] system 00:00: iomem range 0x7f7d1800-0x7f7fffff could not be reserved
[ 0.292486] system 00:00: iomem range 0x7f800000-0x7fffffff could not be reserved
[ 0.292565] system 00:00: iomem range 0xfeda0000-0xfedfffff could not be reserved
[ 0.292644] system 00:00: iomem range 0xffb00000-0xffffffff could not be reserved
[ 0.292723] system 00:00: iomem range 0xfec00000-0xfec0ffff could not be reserved
[ 0.292801] system 00:00: iomem range 0xfee00000-0xfee0ffff could not be reserved
[ 0.292881] system 00:00: iomem range 0xfed20000-0xfed9ffff could not be reserved
[ 0.292960] system 00:00: iomem range 0xf0000000-0xf0003fff could not be reserved
[ 0.293039] system 00:00: iomem range 0xf0004000-0xf0004fff could not be reserved
[ 0.293118] system 00:00: iomem range 0xf0005000-0xf0005fff could not be reserved
[ 0.293197] system 00:00: iomem range 0xf0006000-0xf0006fff could not be reserved
[ 0.293276] system 00:00: iomem range 0xf0008000-0xf000bfff could not be reserved
[ 0.293355] system 00:00: iomem range 0xe0000000-0xefffffff could not be reserved
[ 0.293437] system 00:02: ioport range 0x4d0-0x4d1 has been reserved
[ 0.293498] system 00:02: ioport range 0x1000-0x1005 has been reserved
[ 0.293561] system 00:02: ioport range 0x1008-0x100f has been reserved
[ 0.293625] system 00:03: ioport range 0xf400-0xf4fe has been reserved
[ 0.293686] system 00:03: ioport range 0x1006-0x1007 has been reserved
[ 0.293748] system 00:03: ioport range 0x100a-0x1059 could not be reserved
[ 0.293810] system 00:03: ioport range 0x1060-0x107f has been reserved
[ 0.293871] system 00:03: ioport range 0x1080-0x10bf has been reserved
[ 0.293932] system 00:03: ioport range 0x10c0-0x10df has been reserved
[ 0.293994] system 00:03: ioport range 0x10e0-0x10ff has been reserved
[ 0.295022] system 00:08: ioport range 0x900-0x90f has been reserved
[ 0.295083] system 00:08: ioport range 0x910-0x91f has been reserved
[ 0.295144] system 00:08: ioport range 0x920-0x92f has been reserved
[ 0.295205] system 00:08: ioport range 0x93c-0x93f has been reserved
[ 0.295266] system 00:08: ioport range 0x940-0x97f has been reserved
[ 0.295331] system 00:0d: ioport range 0x930-0x93b has been reserved
[ 0.295395] system 00:0e: ioport range 0x7b0-0x7bb has been reserved
[ 0.295456] system 00:0e: ioport range 0x7c0-0x7df has been reserved
[ 0.295517] system 00:0e: ioport range 0xbb0-0xbbb has been reserved
[ 0.295578] system 00:0e: ioport range 0xbc0-0xbdf has been reserved
[ 0.295639] system 00:0e: ioport range 0xfb0-0xfbb has been reserved
[ 0.295700] system 00:0e: ioport range 0xfc0-0xfdf has been reserved
[ 0.295761] system 00:0e: ioport range 0x13b0-0x13bb has been reserved
[ 0.295823] system 00:0e: ioport range 0x13c0-0x13df has been reserved
[ 0.296021] system 00:0e: ioport range 0x17b0-0x17bb has been reserved
[ 0.296083] system 00:0e: ioport range 0x17c0-0x17df has been reserved
[ 0.296144] system 00:0e: ioport range 0x1bb0-0x1bbb has been reserved
[ 0.296205] system 00:0e: ioport range 0x1bc0-0x1bdf has been reserved
[ 0.296266] system 00:0e: ioport range 0x1fb0-0x1fbb has been reserved
[ 0.296328] system 00:0e: ioport range 0x1fc0-0x1fdf has been reserved
[ 0.296390] system 00:0e: ioport range 0x23b0-0x23bb has been reserved
[ 0.296451] system 00:0e: ioport range 0x23c0-0x23df has been reserved
[ 0.296513] system 00:0e: ioport range 0x27b0-0x27bb has been reserved
[ 0.296574] system 00:0e: ioport range 0x27c0-0x27df has been reserved
[ 0.296635] system 00:0e: ioport range 0x2bb0-0x2bbb has been reserved
[ 0.296696] system 00:0e: ioport range 0x2bc0-0x2bdf has been reserved
[ 0.296758] system 00:0e: ioport range 0x2fb0-0x2fbb has been reserved
[ 0.296820] system 00:0e: ioport range 0x2fc0-0x2fdf has been reserved
[ 0.296881] system 00:0e: ioport range 0x33b0-0x33bb has been reserved
[ 0.296942] system 00:0e: ioport range 0x33c0-0x33df has been reserved
[ 0.297003] system 00:0e: ioport range 0x37b0-0x37bb has been reserved
[ 0.297065] system 00:0e: ioport range 0x37c0-0x37df has been reserved
[ 0.297126] system 00:0e: ioport range 0x3bb0-0x3bbb has been reserved
[ 0.297187] system 00:0e: ioport range 0x3bc0-0x3bdf has been reserved
[ 0.297249] system 00:0e: ioport range 0x3fb0-0x3fbb has been reserved
[ 0.297310] system 00:0e: ioport range 0x3fc0-0x3fdf has been reserved
[ 0.297372] system 00:0e: ioport range 0x43b0-0x43bb has been reserved
[ 0.297434] system 00:0e: ioport range 0x43c0-0x43df has been reserved
[ 0.297495] system 00:0e: ioport range 0x47b0-0x47bb has been reserved
[ 0.297556] system 00:0e: ioport range 0x47c0-0x47df has been reserved
[ 0.297618] system 00:0e: ioport range 0x4bb0-0x4bbb has been reserved
[ 0.297679] system 00:0e: ioport range 0x4bc0-0x4bdf has been reserved
[ 0.297741] system 00:0e: ioport range 0x4fb0-0x4fbb has been reserved
[ 0.297802] system 00:0e: ioport range 0x4fc0-0x4fdf has been reserved
[ 0.297863] system 00:0e: ioport range 0x53b0-0x53bb has been reserved
[ 0.297925] system 00:0e: ioport range 0x53c0-0x53df has been reserved
[ 0.328404] PCI: Bridge: 0000:00:1c.0
[ 0.328460] IO window: disabled.
[ 0.328518] MEM window: 0xdfd00000-0xdfdfffff
[ 0.328577] PREFETCH window: disabled.
[ 0.328643] PCI: Bus 4, cardbus bridge: 0000:03:01.0
[ 0.328700] IO window: 0x00006000-0x000060ff
[ 0.328758] IO window: 0x00006400-0x000064ff
[ 0.328818] PREFETCH window: 0x88000000-0x8bffffff
[ 0.328878] MEM window: 0x8c000000-0x8fffffff
[ 0.328937] PCI: Bridge: 0000:00:1e.0
[ 0.328993] IO window: 6000-6fff
[ 0.329050] MEM window: 0xdfc00000-0xdfcfffff
[ 0.329110] PREFETCH window: 0x0000000088000000-0x000000008bffffff
[ 0.329198] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 0.329310] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 0.329323] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 0.329340] PCI: Enabling device 0000:03:01.0 (0000 -> 0003)
[ 0.329401] ACPI: PCI Interrupt 0000:03:01.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 0.329532] NET: Registered protocol family 2
[ 0.329677] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.329982] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.331073] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.331764] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.331828] TCP reno registered
[ 0.332138] checking if image is initramfs... it is
[ 0.792065] Switched to high resolution mode on CPU 0
[ 0.847036] Freeing initrd memory: 5518k freed
[ 0.847759] audit: initializing netlink socket (disabled)
[ 0.847833] type=2000 audit(1218447577.844:1): initialized
[ 0.848115] highmem bounce pool size: 64 pages
[ 0.848177] Total HugeTLB memory allocated, 0
[ 0.848303] VFS: Disk quotas dquot_6.5.1
[ 0.848385] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.848540] io scheduler noop registered
[ 0.848596] io scheduler anticipatory registered
[ 0.848653] io scheduler deadline registered
[ 0.848719] io scheduler cfq registered (default)
[ 0.848789] pci 0000:00:02.0: Boot video device
[ 0.848986] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 0.849030] assign_interrupt_mode Found MSI capability
[ 0.849132] Allocate Port Service[0000:00:1c.0:pcie00]
[ 0.849172] Allocate Port Service[0000:00:1c.0:pcie02]
[ 0.849207] Allocate Port Service[0000:00:1c.0:pcie03]
[ 0.849535] isapnp: Scanning for PnP cards...
[ 1.203812] isapnp: No Plug & Play device found
[ 1.206294] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 1.206512] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.207026] 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.207212] ACPI: PCI Interrupt 0000:00:1e.3[B] -> GSI 17 (level, low) -> IRQ 17
[ 1.207327] ACPI: PCI interrupt for device 0000:00:1e.3 disabled
[ 1.208390] brd: module loaded
[ 1.208523] PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 1.213529] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.213589] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.213773] mice: PS/2 mouse device common for all mice
[ 1.213884] cpuidle: using governor ladder
[ 1.213940] cpuidle: using governor menu
[ 1.214379] TCP cubic registered
[ 1.214442] NET: Registered protocol family 1
[ 1.214507] NET: Registered protocol family 17
[ 1.214568] Using IPI No-Shortcut mode
[ 1.214739] registered taskstats version 1
[ 1.215037] Freeing unused kernel memory: 244k freed
[ 1.219590] input: AT Translated Set 2 keyboard as /class/input/input0
[ 1.301415] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3])
[ 1.301676] ACPI: ACPI0007:00 is registered as cooling_device0
[ 1.301737] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 1.304730] ACPI: LNXTHERM:01 is registered as thermal_zone0
[ 1.306345] ACPI: Thermal Zone [THM] (78 C)
[ 1.843504] ACPI: ACPI Dock Station Driver
[ 1.876231] tg3.c:v3.90 (April 12, 2008)
[ 1.876321] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 1.876439] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 1.898448] eth0: Tigon3 [partno(BCM95751) rev 4001 PHY(5750)] (PCI Express) 10/100/1000Base-T Ethernet 00:15:c5:0b:fb:92
[ 1.898540] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
[ 1.898619] eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[ 1.920188] usbcore: registered new interface driver usbfs
[ 1.920275] usbcore: registered new interface driver hub
[ 1.928949] usbcore: registered new device driver usb
[ 1.944207] USB Universal Host Controller Interface driver v3.0
[ 1.944309] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 1.944428] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 1.944432] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 1.944627] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[ 1.944738] uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000bf80
[ 1.944914] usb usb1: configuration #1 chosen from 1 choice
[ 1.944995] hub 1-0:1.0: USB hub found
[ 1.945055] hub 1-0:1.0: 2 ports detected
[ 2.048218] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.048286] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.048364] usb usb1: Product: UHCI Host Controller
[ 2.048421] usb usb1: Manufacturer: Linux 2.6.25-1-686 uhci_hcd
[ 2.048480] usb usb1: SerialNumber: 0000:00:1d.0
[ 2.048569] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 17
[ 2.048689] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 2.048693] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 2.048773] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[ 2.048884] uhci_hcd 0000:00:1d.1: irq 17, io base 0x0000bf60
[ 2.049045] usb usb2: configuration #1 chosen from 1 choice
[ 2.049125] hub 2-0:1.0: USB hub found
[ 2.049184] hub 2-0:1.0: 2 ports detected
[ 2.049342] Uniform Multi-Platform E-IDE driver
[ 2.049399] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 2.152226] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.152295] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.152372] usb usb2: Product: UHCI Host Controller
[ 2.152430] usb usb2: Manufacturer: Linux 2.6.25-1-686 uhci_hcd
[ 2.152489] usb usb2: SerialNumber: 0000:00:1d.1
[ 2.152583] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 2.152702] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 2.152706] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 2.152787] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[ 2.152900] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000bf40
[ 2.153062] usb usb3: configuration #1 chosen from 1 choice
[ 2.153141] hub 3-0:1.0: USB hub found
[ 2.153202] hub 3-0:1.0: 2 ports detected
[ 2.172136] Marking TSC unstable due to: TSC halts in idle.
[ 2.288889] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.288952] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.289030] usb usb3: Product: UHCI Host Controller
[ 2.289087] usb usb3: Manufacturer: Linux 2.6.25-1-686 uhci_hcd
[ 2.289146] usb usb3: SerialNumber: 0000:00:1d.2
[ 2.289238] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 19
[ 2.290318] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[ 2.290322] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 2.290401] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[ 2.290509] uhci_hcd 0000:00:1d.3: irq 19, io base 0x0000bf20
[ 2.290671] usb usb4: configuration #1 chosen from 1 choice
[ 2.290750] hub 4-0:1.0: USB hub found
[ 2.290809] hub 4-0:1.0: 2 ports detected
[ 2.320705] Clocksource tsc unstable (delta = -139470011 ns)
[ 2.392560] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.392623] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.392701] usb usb4: Product: UHCI Host Controller
[ 2.392758] usb usb4: Manufacturer: Linux 2.6.25-1-686 uhci_hcd
[ 2.392818] usb usb4: SerialNumber: 0000:00:1d.3
[ 2.401452] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 16 (level, low) -> IRQ 16
[ 2.401571] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 2.401576] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 2.401657] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
[ 2.405637] ehci_hcd 0000:00:1d.7: debug port 1
[ 2.405698] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 2.405704] ehci_hcd 0000:00:1d.7: irq 16, io mem 0xffa80800
[ 2.409889] SCSI subsystem initialized
[ 2.420527] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 2.420736] usb usb5: configuration #1 chosen from 1 choice
[ 2.420820] hub 5-0:1.0: USB hub found
[ 2.420882] hub 5-0:1.0: 8 ports detected
[ 2.424334] libata version 3.00 loaded.
[ 2.524603] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.524673] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.524751] usb usb5: Product: EHCI Host Controller
[ 2.524808] usb usb5: Manufacturer: Linux 2.6.25-1-686 ehci_hcd
[ 2.524867] usb usb5: SerialNumber: 0000:00:1d.7
[ 2.528673] ahci 0000:00:1f.2: version 3.0
[ 2.528698] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level, low) -> IRQ 17
[ 2.528821] ACPI: PCI interrupt for device 0000:00:1f.2 disabled
[ 2.528883] ahci: probe of 0000:00:1f.2 failed with error -22
[ 2.538619] ata_piix 0000:00:1f.2: version 2.12
[ 2.538632] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level, low) -> IRQ 17
[ 2.538745] ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
[ 2.692399] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 2.692566] scsi0 : ata_piix
[ 2.692789] scsi1 : ata_piix
[ 2.694789] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xbfa0 irq 14
[ 2.694852] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xbfa8 irq 15
[ 2.856760] ata1.00: ATA-6: ST960822A, 8.03, max UDMA/100
[ 2.856820] ata1.00: 117210240 sectors, multi 8: LBA48
[ 2.856879] ata1.00: applying bridge limits
[ 2.872650] ata1.00: configured for UDMA/100
[ 3.151151] usb 3-2: new low speed USB device using uhci_hcd and address 2
[ 3.207316] ata2.00: ATAPI: TSSTcorpCD-RW/DVD-ROM TSL462C, DE01, max UDMA/33
[ 3.326550] usb 3-2: configuration #1 chosen from 1 choice
[ 3.326550] usb 3-2: New USB device found, idVendor=046d, idProduct=c024
[ 3.326550] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3.326550] usb 3-2: Product: USB-PS/2 Optical Mouse
[ 3.326550] usb 3-2: Manufacturer: B16_b_02
[ 3.357447] usbcore: registered new interface driver hiddev
[ 3.371005] input: B16_b_02 USB-PS/2 Optical Mouse as /class/input/input1
[ 3.371005] input,hidraw0: USB HID v1.10 Mouse [B16_b_02 USB-PS/2 Optical Mouse] on usb-0000:00:1d.2-2
[ 3.371005] usbcore: registered new interface driver usbhid
[ 3.371005] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 3.387412] ata2.00: configured for UDMA/33
[ 3.387614] scsi 0:0:0:0: Direct-Access ATA ST960822A 8.03 PQ: 0 ANSI: 5
[ 3.388376] scsi 1:0:0:0: CD-ROM TSSTcorp CDRW/DVD TSL462C DE01 PQ: 0 ANSI: 5
[ 3.434895] Driver 'sd' needs updating - please use bus_type methods
[ 3.435060] sd 0:0:0:0: [sda] 117210240 512-byte hardware sectors (60012 MB)
[ 3.435141] sd 0:0:0:0: [sda] Write Protect is off
[ 3.435199] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.435232] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.435378] sd 0:0:0:0: [sda] 117210240 512-byte hardware sectors (60012 MB)
[ 3.435455] sd 0:0:0:0: [sda] Write Protect is off
[ 3.435512] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.435544] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.435626] sda:<4>Driver 'sr' needs updating - please use bus_type methods
[ 3.458255] sda1 sda2 sda3
[ 3.458255] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.460445] sr0: scsi3-mmc drive: 10x/24x writer cd/rw xa/form2 cdda tray
[ 3.460510] Uniform CD-ROM driver Revision: 3.20
[ 3.460616] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 3.477223] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 3.477306] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 3.718653] EXT3-fs: INFO: recovery required on readonly filesystem.
[ 3.718722] EXT3-fs: write access will be enabled during recovery.
[ 4.161480] kjournald starting. Commit interval 5 seconds
[ 4.161480] EXT3-fs: sda1: orphan cleanup on readonly fs
[ 4.161480] ext3_orphan_cleanup: deleting unreferenced inode 618958
[ 4.161480] ext3_orphan_cleanup: deleting unreferenced inode 618956
[ 4.161480] ext3_orphan_cleanup: deleting unreferenced inode 618954
[ 4.161480] ext3_orphan_cleanup: deleting unreferenced inode 618953
[ 4.161480] ext3_orphan_cleanup: deleting unreferenced inode 618952
[ 4.161480] ext3_orphan_cleanup: deleting unreferenced inode 895898
[ 4.161480] EXT3-fs: sda1: 6 orphan inodes deleted
[ 4.161480] EXT3-fs: recovery complete.
[ 4.183727] EXT3-fs: mounted filesystem with ordered data mode.
[ 10.859137] udevd version 125 started
[ 11.447819] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[ 11.713360] Linux agpgart interface v0.103
[ 11.726094] agpgart: Detected an Intel 915GM Chipset.
[ 11.726521] agpgart: Detected 7932K stolen memory.
[ 11.743522] agpgart: AGP aperture is 256M @ 0xc0000000
[ 12.133453] ACPI: AC Adapter [AC] (on-line)
[ 12.511852] ACPI: Battery Slot [BAT0] (battery present)
[ 12.511964] ACPI: Battery Slot [BAT1] (battery absent)
[ 12.512163] input: Lid Switch as /class/input/input2
[ 12.523823] ACPI: Lid Switch [LID]
[ 12.523931] input: Power Button (CM) as /class/input/input3
[ 12.555294] ACPI: Power Button (CM) [PBTN]
[ 12.555411] input: Sleep Button (CM) as /class/input/input4
[ 12.583296] ACPI: Sleep Button (CM) [SBTN]
[ 13.169591] ACPI: \_SB_.PCI0.IDE0.SEC0.MAST: found ejectable bay
[ 13.169597] ACPI: \_SB_.PCI0.IDE0.SEC0.MAST: Adding notify handler
[ 13.169626] ACPI: Error installing bay notify handler
[ 13.169690] ACPI: Bay [\_SB_.PCI0.IDE0.SEC0.MAST] Added
[ 13.224361] input: Video Bus as /class/input/input5
[ 13.251332] ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
[ 13.251892] input: Video Bus as /class/input/input6
[ 13.279340] ACPI: Video Device [VID1] (multi-head: yes rom: no post: no)
[ 13.279553] input: Video Bus as /class/input/input7
[ 13.311341] ACPI: Video Device [VID2] (multi-head: yes rom: no post: no)
[ 13.663001] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
[ 13.663141] iTCO_wdt: Found a ICH6-M TCO device (Version=2, TCOBASE=0x1060)
[ 13.663231] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 13.923069] intel_rng: FWH not detected
[ 13.987477] ACPI: PCI Interrupt 0000:00:1e.3[B] -> GSI 17 (level, low) -> IRQ 17
[ 13.987607] PCI: Setting latency timer of device 0000:00:1e.3 to 64
[ 14.091398] MC'97 1 converters and GPIO not ready (0xff00)
[ 14.171275] Yenta: CardBus bridge found at 0000:03:01.0 [1028:0182]
[ 14.171369] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 14.171428] Yenta: Routing CardBus interrupts to PCI
[ 14.171489] Yenta TI: socket 0000:03:01.0, mfunc 0x01111122, devctl 0x64
[ 14.188464] input: PC Speaker as /class/input/input8
[ 14.282084] ieee80211_crypt: registered algorithm 'NULL'
[ 14.297194] ieee80211: 802.11 data/management/control stack, git-1.1.13
[ 14.297261] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[ 14.370738] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[ 14.370833] rtc0: alarms up to one month, y3k
[ 14.406314] Yenta: ISA IRQ mask 0x0cf8, PCI irq 19
[ 14.406378] Socket status: 30000006
[ 14.406432] Yenta: Raising subordinate bus# of parent bus (#03) from #04 to #07
[ 14.406513] pcmcia: parent PCI bridge I/O window: 0x6000 - 0x6fff
[ 14.406604] cs: IO port probe 0x6000-0x6fff: clean.
[ 14.407029] pcmcia: parent PCI bridge Memory window: 0xdfc00000 - 0xdfcfffff
[ 14.407091] pcmcia: parent PCI bridge Memory window: 0x88000000 - 0x8bffffff
[ 14.464511] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq
[ 14.464596] ipw2200: Copyright(c) 2003-2006 Intel Corporation
[ 14.464712] ACPI: PCI Interrupt 0000:03:03.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 14.483391] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
[ 14.907816] input: PS/2 Mouse as /class/input/input9
[ 14.956692] input: AlpsPS/2 ALPS GlidePoint as /class/input/input10
[ 14.991690] parport_pc 00:0c: reported by Plug and Play ACPI
[ 14.991818] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[ 15.367132] cs: IO port probe 0x100-0x3af: clean.
[ 15.368889] cs: IO port probe 0x3e0-0x4ff: clean.
[ 15.369654] cs: IO port probe 0x820-0x8ff: clean.
[ 15.370318] cs: IO port probe 0xc00-0xcf7: clean.
[ 15.371109] cs: IO port probe 0xa00-0xaff: clean.
[ 15.484997] ipw2200: Detected geography ZZD (13 802.11bg channels, 0 802.11a channels)
[ 15.485161] ACPI: PCI Interrupt 0000:00:1e.2[A] -> GSI 16 (level, low) -> IRQ 16
[ 15.485292] PCI: Setting latency timer of device 0000:00:1e.2 to 64
[ 16.314571] intel8x0_measure_ac97_clock: measured 55368 usecs
[ 16.314638] intel8x0: clocking to 48000
[ 16.469358] device-mapper: uevent: version 1.0.3
[ 16.470753] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
[ 17.076325] EXT3 FS on sda1, internal journal
[ 17.242428] vboxdrv: Trying to deactivate the NMI watchdog permanently...
[ 17.242432] vboxdrv: Successfully done.
[ 17.242434] vboxdrv: Found 1 processor cores.
[ 17.242436] vboxdrv: fAsync=0 u64DiffCores=1.
[ 17.242468] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[ 17.242547] vboxdrv: Successfully loaded version 1.6.2_OSE (interface 0x00070002).
[ 18.482746] kjournald starting. Commit interval 5 seconds
[ 18.482986] EXT3 FS on sda2, internal journal
[ 18.482986] EXT3-fs: mounted filesystem with ordered data mode.
[ 18.494085] kjournald starting. Commit interval 5 seconds
[ 18.494307] EXT3 FS on sda3, internal journal
[ 18.494307] EXT3-fs: mounted filesystem with ordered data mode.
[ 19.953815] fuse init (API version 7.9)
[ 25.585774] NET: Registered protocol family 10
[ 25.586343] lo: Disabled Privacy Extensions
[ 26.821599] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 28.014490] Bridge firewalling registered
[ 28.015841] bridge0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
[ 28.063975] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 28.103201] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 28.429420] Netfilter messages via NETLINK v0.30.
[ 28.433099] ctnetlink v0.93: registering with nfnetlink.
[ 28.879541] tun: Universal TUN/TAP device driver, 1.6
[ 28.879541] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 29.916556] device vbox0 entered promiscuous mode
[ 29.916556] bridge0: port 1(vbox0) entering learning state
[ 30.867765] bridge0: topology change detected, propagating
[ 30.867845] bridge0: port 1(vbox0) entering forwarding state
[ 38.282889] bridge0: no IPv6 routers present
[ 39.026379] vbox0: no IPv6 routers present
[ 39.878066] Bluetooth: Core ver 2.11
[ 39.879828] NET: Registered protocol family 31
[ 39.879891] Bluetooth: HCI device and connection manager initialized
[ 39.879952] Bluetooth: HCI socket layer initialized
[ 39.952186] Bluetooth: L2CAP ver 2.9
[ 39.952249] Bluetooth: L2CAP socket layer initialized
[ 40.014606] Bluetooth: RFCOMM socket layer initialized
[ 40.014679] Bluetooth: RFCOMM TTY layer initialized
[ 40.014735] Bluetooth: RFCOMM ver 1.8
[ 41.379013] lp0: using parport0 (interrupt-driven).
[ 41.406916] ppdev: user-space parallel port driver
[ 45.968930] [drm] Initialized drm 1.1.0 20060810
[ 46.049896] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 46.049908] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 46.049974] [drm] Initialized i915 1.6.0 20060119 on minor 0
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 522193
[ 0.000000] On node 0 totalpages: 522193
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 2287 pages used for memmap
[ 0.000000] HighMem zone: 290530 pages, LIFO batch:31
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI 2.3 present.
[ 0.000000] ACPI: RSDP 000FC9B0, 0014 (r0 DELL )
[ 0.000000] ACPI: RSDT 7F7D1F90, 0040 (r1 DELL CPi R 27D50A02 ASL 61)
[ 0.000000] ACPI: FACP 7F7D2C00, 0074 (r1 DELL CPi R 27D50A02 ASL 61)
[ 0.000000] ACPI: DSDT 7F7D3800, 3C51 (r1 INT430 SYSFexxx 1001 MSFT 100000E)
[ 0.000000] ACPI: FACS 7F7E2000, 0040
[ 0.000000] ACPI: APIC 7F7D3400, 0068 (r1 DELL CPi R 27D50A02 ASL 47)
[ 0.000000] ACPI: ASF! 7F7D3000, 005B (r16 DELL CPi R 27D50A02 ASL 61)
[ 0.000000] ACPI: MCFG 7F7D33C0, 003E (r16 DELL CPi R 27D50A02 ASL 61)
[ 0.000000] ACPI: SSDT 7F7D23E6, 023E (r1 PmRef Cpu0Ist 3000 INTL 20030522)
[ 0.000000] ACPI: SSDT 7F7D220E, 01D8 (r1 PmRef Cpu0Cst 3001 INTL 20030522)
[ 0.000000] ACPI: SSDT 7F7D2013, 01FB (r1 PmRef CpuPm 3000 INTL 20030522)
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 6:13 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 0000000000100000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 518114
[ 0.000000] Kernel command line: root=/dev/sda1 ro
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 1729.029 MHz processor.
[ 0.001499] Console: colour VGA+ 80x25
[ 0.001503] console [tty0] enabled
[ 0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.004000] Memory: 2060872k/2088772k available (1753k kernel code, 26548k reserved, 728k data, 252k init, 1171268k highmem)
[ 0.004000] virtual kernel memory layout:
[ 0.004000] fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB)
[ 0.004000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.004000] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 0.004000] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 0.004000] .init : 0xc0375000 - 0xc03b4000 ( 252 kB)
[ 0.004000] .data : 0xc02b649a - 0xc036c640 ( 728 kB)
[ 0.004000] .text : 0xc0100000 - 0xc02b649a (1753 kB)
[ 0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.084009] Calibrating delay using timer specific routine.. 3462.09 BogoMIPS (lpj=6924195)
[ 0.084161] Security Framework initialized
[ 0.084221] SELinux: Disabled at boot.
[ 0.084278] Capability LSM initialized
[ 0.084347] Mount-cache hash table entries: 512
[ 0.084571] Initializing cgroup subsys ns
[ 0.084630] Initializing cgroup subsys cpuacct
[ 0.084706] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.084794] CPU: L2 cache: 2048K
[ 0.084850] Intel machine check architecture supported.
[ 0.084910] Intel machine check reporting enabled on CPU#0.
[ 0.084972] Compat vDSO mapped to ffffe000.
[ 0.085033] Checking 'hlt' instruction... OK.
[ 0.100356] SMP alternatives: switching to UP code
[ 0.102499] Freeing SMP alternatives: 16k freed
[ 0.102556] ACPI: Core revision 20070126
[ 0.112057] CPU0: Intel(R) Pentium(R) M processor 1.73GHz stepping 08
[ 0.112198] Total of 1 processors activated (3462.09 BogoMIPS).
[ 0.112447] ENABLING IO-APIC IRQs
[ 0.112694] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.156009] Brought up 1 CPUs
[ 0.156009] CPU0 attaching sched-domain:
[ 0.156009] domain 0: span 01
[ 0.156009] groups: 01
[ 0.156009] net_namespace: 548 bytes
[ 0.156009] Booting paravirtualized kernel on bare hardware
[ 0.156009] NET: Registered protocol family 16
[ 0.156009] ACPI: bus type pci registered
[ 0.156009] PCI: Using MMCONFIG for extended config space
[ 0.156009] PCI: Using configuration type 1
[ 0.156009] Setting up standard PCI resources
[ 0.156010] ACPI: EC: Look up EC in DSDT
[ 0.170044] ACPI: SSDT 7F7D1FD0, 0043 (r1 LMPWR DELLLOM 1001 INTL 20030522)
[ 0.170307] ACPI: Interpreter enabled
[ 0.170363] ACPI: (supports S0 S3 S4 S5)
[ 0.170549] ACPI: Using IOAPIC for interrupt routing
[ 0.199231] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.200026] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
[ 0.200033] pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
[ 0.200114] pci 0000:00:1f.0: quirk: region 1080-10bf claimed by ICH6 GPIO
[ 0.200676] PCI: Transparent bridge - 0000:00:1e.0
[ 0.200779] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.201244] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT]
[ 0.220328] ACPI: PCI Interrupt Link [LNKA] (IRQs 9 10 *11)
[ 0.220659] ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7) *10
[ 0.220988] ACPI: PCI Interrupt Link [LNKC] (IRQs *9 10 11)
[ 0.221322] ACPI: PCI Interrupt Link [LNKD] (IRQs *5 7 9 10 11)
[ 0.221701] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.222338] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.222975] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.224360] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.224447] pnp: PnP ACPI init
[ 0.224506] ACPI: bus type pnp registered
[ 0.284405] pnpacpi: exceeded the max number of IO resources: 40
[ 0.285236] pnp: PnP ACPI: found 15 devices
[ 0.285292] ACPI: ACPI bus type pnp unregistered
[ 0.285351] PnPBIOS: Disabled by ACPI PNP
[ 0.285616] PCI: Using ACPI for IRQ routing
[ 0.285673] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 0.286005] hpet clockevent registered
[ 0.286012] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.286192] hpet0: 3 64-bit timers, 14318180 Hz
[ 0.287307] system 00:00: iomem range 0x0-0x9fbff could not be reserved
[ 0.287370] system 00:00: iomem range 0x9fc00-0x9ffff could not be reserved
[ 0.287432] system 00:00: iomem range 0xc0000-0xcffff could not be reserved
[ 0.287494] system 00:00: iomem range 0xe0000-0xfffff could not be reserved
[ 0.287557] system 00:00: iomem range 0x100000-0x7f7d17ff could not be reserved
[ 0.287635] system 00:00: iomem range 0x7f7d1800-0x7f7fffff could not be reserved
[ 0.287714] system 00:00: iomem range 0x7f800000-0x7fffffff could not be reserved
[ 0.287793] system 00:00: iomem range 0xfeda0000-0xfedfffff could not be reserved
[ 0.288021] system 00:00: iomem range 0xffb00000-0xffffffff could not be reserved
[ 0.288100] system 00:00: iomem range 0xfec00000-0xfec0ffff could not be reserved
[ 0.288179] system 00:00: iomem range 0xfee00000-0xfee0ffff could not be reserved
[ 0.288257] system 00:00: iomem range 0xfed20000-0xfed9ffff could not be reserved
[ 0.288336] system 00:00: iomem range 0xf0000000-0xf0003fff could not be reserved
[ 0.288415] system 00:00: iomem range 0xf0004000-0xf0004fff could not be reserved
[ 0.288494] system 00:00: iomem range 0xf0005000-0xf0005fff could not be reserved
[ 0.288573] system 00:00: iomem range 0xf0006000-0xf0006fff could not be reserved
[ 0.288652] system 00:00: iomem range 0xf0008000-0xf000bfff could not be reserved
[ 0.288731] system 00:00: iomem range 0xe0000000-0xefffffff could not be reserved
[ 0.288814] system 00:02: ioport range 0x4d0-0x4d1 has been reserved
[ 0.288875] system 00:02: ioport range 0x1000-0x1005 has been reserved
[ 0.288939] system 00:02: ioport range 0x1008-0x100f has been reserved
[ 0.289003] system 00:03: ioport range 0xf400-0xf4fe has been reserved
[ 0.289064] system 00:03: ioport range 0x1006-0x1007 has been reserved
[ 0.289126] system 00:03: ioport range 0x100a-0x1059 could not be reserved
[ 0.289189] system 00:03: ioport range 0x1060-0x107f has been reserved
[ 0.289251] system 00:03: ioport range 0x1080-0x10bf has been reserved
[ 0.289312] system 00:03: ioport range 0x10c0-0x10df has been reserved
[ 0.289373] system 00:03: ioport range 0x10e0-0x10ff has been reserved
[ 0.290404] system 00:08: ioport range 0x900-0x90f has been reserved
[ 0.290465] system 00:08: ioport range 0x910-0x91f has been reserved
[ 0.290526] system 00:08: ioport range 0x920-0x92f has been reserved
[ 0.290587] system 00:08: ioport range 0x93c-0x93f has been reserved
[ 0.290649] system 00:08: ioport range 0x940-0x97f has been reserved
[ 0.290714] system 00:0d: ioport range 0x930-0x93b has been reserved
[ 0.290778] system 00:0e: ioport range 0x7b0-0x7bb has been reserved
[ 0.290839] system 00:0e: ioport range 0x7c0-0x7df has been reserved
[ 0.290900] system 00:0e: ioport range 0xbb0-0xbbb has been reserved
[ 0.290961] system 00:0e: ioport range 0xbc0-0xbdf has been reserved
[ 0.291022] system 00:0e: ioport range 0xfb0-0xfbb has been reserved
[ 0.291082] system 00:0e: ioport range 0xfc0-0xfdf has been reserved
[ 0.291144] system 00:0e: ioport range 0x13b0-0x13bb has been reserved
[ 0.291206] system 00:0e: ioport range 0x13c0-0x13df has been reserved
[ 0.291268] system 00:0e: ioport range 0x17b0-0x17bb has been reserved
[ 0.291329] system 00:0e: ioport range 0x17c0-0x17df has been reserved
[ 0.291391] system 00:0e: ioport range 0x1bb0-0x1bbb has been reserved
[ 0.291452] system 00:0e: ioport range 0x1bc0-0x1bdf has been reserved
[ 0.291513] system 00:0e: ioport range 0x1fb0-0x1fbb has been reserved
[ 0.291574] system 00:0e: ioport range 0x1fc0-0x1fdf has been reserved
[ 0.291636] system 00:0e: ioport range 0x23b0-0x23bb has been reserved
[ 0.291697] system 00:0e: ioport range 0x23c0-0x23df has been reserved
[ 0.291758] system 00:0e: ioport range 0x27b0-0x27bb has been reserved
[ 0.291820] system 00:0e: ioport range 0x27c0-0x27df has been reserved
[ 0.291881] system 00:0e: ioport range 0x2bb0-0x2bbb has been reserved
[ 0.291943] system 00:0e: ioport range 0x2bc0-0x2bdf has been reserved
[ 0.292004] system 00:0e: ioport range 0x2fb0-0x2fbb has been reserved
[ 0.292020] system 00:0e: ioport range 0x2fc0-0x2fdf has been reserved
[ 0.292082] system 00:0e: ioport range 0x33b0-0x33bb has been reserved
[ 0.292143] system 00:0e: ioport range 0x33c0-0x33df has been reserved
[ 0.292205] system 00:0e: ioport range 0x37b0-0x37bb has been reserved
[ 0.292265] system 00:0e: ioport range 0x37c0-0x37df has been reserved
[ 0.292327] system 00:0e: ioport range 0x3bb0-0x3bbb has been reserved
[ 0.292388] system 00:0e: ioport range 0x3bc0-0x3bdf has been reserved
[ 0.292449] system 00:0e: ioport range 0x3fb0-0x3fbb has been reserved
[ 0.292511] system 00:0e: ioport range 0x3fc0-0x3fdf has been reserved
[ 0.292572] system 00:0e: ioport range 0x43b0-0x43bb has been reserved
[ 0.292633] system 00:0e: ioport range 0x43c0-0x43df has been reserved
[ 0.292695] system 00:0e: ioport range 0x47b0-0x47bb has been reserved
[ 0.292756] system 00:0e: ioport range 0x47c0-0x47df has been reserved
[ 0.292818] system 00:0e: ioport range 0x4bb0-0x4bbb has been reserved
[ 0.292879] system 00:0e: ioport range 0x4bc0-0x4bdf has been reserved
[ 0.292941] system 00:0e: ioport range 0x4fb0-0x4fbb has been reserved
[ 0.293003] system 00:0e: ioport range 0x4fc0-0x4fdf has been reserved
[ 0.293064] system 00:0e: ioport range 0x53b0-0x53bb has been reserved
[ 0.293126] system 00:0e: ioport range 0x53c0-0x53df has been reserved
[ 0.323630] PCI: Bridge: 0000:00:1c.0
[ 0.323685] IO window: disabled.
[ 0.323744] MEM window: 0xdfd00000-0xdfdfffff
[ 0.323803] PREFETCH window: disabled.
[ 0.323868] PCI: Bus 4, cardbus bridge: 0000:03:01.0
[ 0.323925] IO window: 0x00006000-0x000060ff
[ 0.323985] IO window: 0x00006400-0x000064ff
[ 0.324025] PREFETCH window: 0x88000000-0x8bffffff
[ 0.324086] MEM window: 0x8c000000-0x8fffffff
[ 0.324145] PCI: Bridge: 0000:00:1e.0
[ 0.324200] IO window: 6000-6fff
[ 0.324258] MEM window: 0xdfc00000-0xdfcfffff
[ 0.324317] PREFETCH window: 0x0000000088000000-0x000000008bffffff
[ 0.324405] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 0.324517] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 0.324530] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 0.324547] PCI: Enabling device 0000:03:01.0 (0000 -> 0003)
[ 0.324608] ACPI: PCI Interrupt 0000:03:01.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 0.324739] NET: Registered protocol family 2
[ 0.324881] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.325190] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.326268] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.326960] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.327024] TCP reno registered
[ 0.327328] checking if image is initramfs... it is
[ 0.788065] Switched to high resolution mode on CPU 0
[ 0.910555] Freeing initrd memory: 6232k freed
[ 0.911289] audit: initializing netlink socket (disabled)
[ 0.911364] type=2000 audit(1218443863.908:1): initialized
[ 0.911623] highmem bounce pool size: 64 pages
[ 0.911683] Total HugeTLB memory allocated, 0
[ 0.911809] VFS: Disk quotas dquot_6.5.1
[ 0.911889] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.912076] io scheduler noop registered
[ 0.912132] io scheduler anticipatory registered
[ 0.912188] io scheduler deadline registered
[ 0.912257] io scheduler cfq registered (default)
[ 0.912325] pci 0000:00:02.0: Boot video device
[ 0.912520] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 0.912565] assign_interrupt_mode Found MSI capability
[ 0.912665] Allocate Port Service[0000:00:1c.0:pcie00]
[ 0.912705] Allocate Port Service[0000:00:1c.0:pcie02]
[ 0.912739] Allocate Port Service[0000:00:1c.0:pcie03]
[ 0.913057] isapnp: Scanning for PnP cards...
[ 1.268197] isapnp: No Plug & Play device found
[ 1.270676] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 1.270899] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.271416] 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.271601] ACPI: PCI Interrupt 0000:00:1e.3[B] -> GSI 17 (level, low) -> IRQ 17
[ 1.271715] ACPI: PCI interrupt for device 0000:00:1e.3 disabled
[ 1.272498] brd: module loaded
[ 1.272633] PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 1.276951] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.277012] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.277201] mice: PS/2 mouse device common for all mice
[ 1.277314] cpuidle: using governor ladder
[ 1.277370] cpuidle: using governor menu
[ 1.277807] TCP cubic registered
[ 1.277871] NET: Registered protocol family 1
[ 1.277934] NET: Registered protocol family 17
[ 1.277998] Using IPI No-Shortcut mode
[ 1.278169] registered taskstats version 1
[ 1.278472] Freeing unused kernel memory: 252k freed
[ 1.282125] input: AT Translated Set 2 keyboard as /class/input/input0
[ 1.366780] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3])
[ 1.367039] ACPI: ACPI0007:00 is registered as cooling_device0
[ 1.367100] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 1.370036] ACPI: LNXTHERM:01 is registered as thermal_zone0
[ 1.371798] ACPI: Thermal Zone [THM] (72 C)
[ 1.931607] ACPI: ACPI Dock Station Driver
[ 1.958087] tg3.c:v3.91 (April 18, 2008)
[ 1.958176] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 1.958294] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 1.982194] eth0: Tigon3 [partno(BCM95751) rev 4001 PHY(5750)] (PCI Express) 10/100/1000Base-T Ethernet 00:15:c5:0b:fb:92
[ 1.982286] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
[ 1.982365] eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[ 1.992074] usbcore: registered new interface driver usbfs
[ 1.992152] usbcore: registered new interface driver hub
[ 2.004212] usbcore: registered new device driver usb
[ 2.018577] USB Universal Host Controller Interface driver v3.0
[ 2.018681] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 2.018800] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 2.018805] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 2.018993] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[ 2.019106] uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000bf80
[ 2.019282] usb usb1: configuration #1 chosen from 1 choice
[ 2.019364] hub 1-0:1.0: USB hub found
[ 2.019423] hub 1-0:1.0: 2 ports detected
[ 2.120231] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.120301] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.120379] usb usb1: Product: UHCI Host Controller
[ 2.120436] usb usb1: Manufacturer: Linux 2.6.25-2-686 uhci_hcd
[ 2.120495] usb usb1: SerialNumber: 0000:00:1d.0
[ 2.120585] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 17
[ 2.120705] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 2.120709] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 2.120791] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[ 2.120901] uhci_hcd 0000:00:1d.1: irq 17, io base 0x0000bf60
[ 2.121064] usb usb2: configuration #1 chosen from 1 choice
[ 2.121144] hub 2-0:1.0: USB hub found
[ 2.121204] hub 2-0:1.0: 2 ports detected
[ 2.151260] Uniform Multi-Platform E-IDE driver
[ 2.151323] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 2.224230] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.224298] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.224376] usb usb2: Product: UHCI Host Controller
[ 2.224433] usb usb2: Manufacturer: Linux 2.6.25-2-686 uhci_hcd
[ 2.224492] usb usb2: SerialNumber: 0000:00:1d.1
[ 2.224587] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 2.224706] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 2.224710] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 2.224791] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[ 2.224902] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000bf40
[ 2.225065] usb usb3: configuration #1 chosen from 1 choice
[ 2.225144] hub 3-0:1.0: USB hub found
[ 2.225205] hub 3-0:1.0: 2 ports detected
[ 2.292143] Marking TSC unstable due to: TSC halts in idle.
[ 2.444869] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.444932] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.445010] usb usb3: Product: UHCI Host Controller
[ 2.445067] usb usb3: Manufacturer: Linux 2.6.25-2-686 uhci_hcd
[ 2.445127] usb usb3: SerialNumber: 0000:00:1d.2
[ 2.445221] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 19
[ 2.446307] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[ 2.446313] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 2.446391] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[ 2.446501] uhci_hcd 0000:00:1d.3: irq 19, io base 0x0000bf20
[ 2.446664] usb usb4: configuration #1 chosen from 1 choice
[ 2.446743] hub 4-0:1.0: USB hub found
[ 2.446802] hub 4-0:1.0: 2 ports detected
[ 2.548512] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.548575] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.548652] usb usb4: Product: UHCI Host Controller
[ 2.548709] usb usb4: Manufacturer: Linux 2.6.25-2-686 uhci_hcd
[ 2.548769] usb usb4: SerialNumber: 0000:00:1d.3
[ 2.557546] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 16 (level, low) -> IRQ 16
[ 2.557666] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 2.557670] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 2.557755] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
[ 2.561730] ehci_hcd 0000:00:1d.7: debug port 1
[ 2.561792] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 2.561798] ehci_hcd 0000:00:1d.7: irq 16, io mem 0xffa80800
[ 2.565981] SCSI subsystem initialized
[ 2.576478] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 2.576688] usb usb5: configuration #1 chosen from 1 choice
[ 2.576770] hub 5-0:1.0: USB hub found
[ 2.576832] hub 5-0:1.0: 8 ports detected
[ 2.580294] libata version 3.00 loaded.
[ 2.680558] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.680626] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.680705] usb usb5: Product: EHCI Host Controller
[ 2.680762] usb usb5: Manufacturer: Linux 2.6.25-2-686 ehci_hcd
[ 2.680821] usb usb5: SerialNumber: 0000:00:1d.7
[ 2.684806] ahci 0000:00:1f.2: version 3.0
[ 2.684833] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level, low) -> IRQ 17
[ 2.684958] ACPI: PCI interrupt for device 0000:00:1f.2 disabled
[ 2.685020] ahci: probe of 0000:00:1f.2 failed with error -22
[ 2.692867] ata_piix 0000:00:1f.2: version 2.12
[ 2.692879] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level, low) -> IRQ 17
[ 2.692992] ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
[ 2.848259] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 2.848428] scsi0 : ata_piix
[ 2.848652] scsi1 : ata_piix
[ 2.850825] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xbfa0 irq 14
[ 2.850888] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xbfa8 irq 15
[ 2.884153] hub 5-0:1.0: unable to enumerate USB device on port 6
[ 2.900093] Clocksource tsc unstable (delta = -372054713 ns)
[ 3.014099] ata1.00: ATA-6: ST960822A, 8.03, max UDMA/100
[ 3.014159] ata1.00: 117210240 sectors, multi 8: LBA48
[ 3.014217] ata1.00: applying bridge limits
[ 3.028650] ata1.00: configured for UDMA/100
[ 3.235208] usb 3-2: new low speed USB device using uhci_hcd and address 2
[ 3.363242] ata2.00: ATAPI: TSSTcorpCD-RW/DVD-ROM TSL462C, DE01, max UDMA/33
[ 3.410964] usb 3-2: configuration #1 chosen from 1 choice
[ 3.410964] usb 3-2: New USB device found, idVendor=046d, idProduct=c024
[ 3.410964] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3.410968] usb 3-2: Product: USB-PS/2 Optical Mouse
[ 3.411025] usb 3-2: Manufacturer: B16_b_02
[ 3.440643] usbcore: registered new interface driver hiddev
[ 3.453726] input: B16_b_02 USB-PS/2 Optical Mouse as /class/input/input1
[ 3.453726] input,hidraw0: USB HID v1.10 Mouse [B16_b_02 USB-PS/2 Optical Mouse] on usb-0000:00:1d.2-2
[ 3.453726] usbcore: registered new interface driver usbhid
[ 3.453726] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 3.546071] ata2.00: configured for UDMA/33
[ 3.546260] scsi 0:0:0:0: Direct-Access ATA ST960822A 8.03 PQ: 0 ANSI: 5
[ 3.547019] scsi 1:0:0:0: CD-ROM TSSTcorp CDRW/DVD TSL462C DE01 PQ: 0 ANSI: 5
[ 3.577187] Driver 'sd' needs updating - please use bus_type methods
[ 3.577346] sd 0:0:0:0: [sda] 117210240 512-byte hardware sectors (60012 MB)
[ 3.577426] sd 0:0:0:0: [sda] Write Protect is off
[ 3.577484] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.577516] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.577662] sd 0:0:0:0: [sda] 117210240 512-byte hardware sectors (60012 MB)
[ 3.577704] sd 0:0:0:0: [sda] Write Protect is off
[ 3.577761] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.577793] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.577875] sda:<4>Driver 'sr' needs updating - please use bus_type methods
[ 3.669810] sda1 sda2 sda3
[ 3.669810] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.669810] sr0: scsi3-mmc drive: 10x/24x writer cd/rw xa/form2 cdda tray
[ 3.669810] Uniform CD-ROM driver Revision: 3.20
[ 3.669810] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 3.685748] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 3.685835] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 3.812475] device-mapper: uevent: version 1.0.3
[ 3.813711] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
[ 3.862612] kjournald starting. Commit interval 5 seconds
[ 3.862612] EXT3-fs: mounted filesystem with ordered data mode.
[ 10.450562] udevd version 125 started
[ 10.856632] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[ 11.283601] Linux agpgart interface v0.103
[ 11.319755] agpgart: Detected an Intel 915GM Chipset.
[ 11.320156] agpgart: Detected 7932K stolen memory.
[ 11.337151] agpgart: AGP aperture is 256M @ 0xc0000000
[ 11.666737] ACPI: AC Adapter [AC] (on-line)
[ 12.135238] ACPI: Battery Slot [BAT0] (battery present)
[ 12.135350] ACPI: Battery Slot [BAT1] (battery absent)
[ 12.135529] input: Lid Switch as /class/input/input2
[ 12.147256] ACPI: Lid Switch [LID]
[ 12.147366] input: Power Button (CM) as /class/input/input3
[ 12.170712] ACPI: Power Button (CM) [PBTN]
[ 12.170819] input: Sleep Button (CM) as /class/input/input4
[ 12.198715] ACPI: Sleep Button (CM) [SBTN]
[ 12.774049] ACPI: \_SB_.PCI0.IDE0.SEC0.MAST: found ejectable bay
[ 12.774054] ACPI: \_SB_.PCI0.IDE0.SEC0.MAST: Adding notify handler
[ 12.774086] ACPI: Error installing bay notify handler
[ 12.774149] ACPI: Bay [\_SB_.PCI0.IDE0.SEC0.MAST] Added
[ 12.859760] input: Video Bus as /class/input/input5
[ 12.890765] ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
[ 12.891322] input: Video Bus as /class/input/input6
[ 12.922775] ACPI: Video Device [VID1] (multi-head: yes rom: no post: no)
[ 12.922985] input: Video Bus as /class/input/input7
[ 12.954771] ACPI: Video Device [VID2] (multi-head: yes rom: no post: no)
[ 13.293626] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
[ 13.293770] iTCO_wdt: Found a ICH6-M TCO device (Version=2, TCOBASE=0x1060)
[ 13.293859] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 13.478912] ACPI: PCI Interrupt 0000:00:1e.3[B] -> GSI 17 (level, low) -> IRQ 17
[ 13.479044] PCI: Setting latency timer of device 0000:00:1e.3 to 64
[ 13.582815] MC'97 1 converters and GPIO not ready (0xff00)
[ 13.595893] intel_rng: FWH not detected
[ 13.710872] input: PC Speaker as /class/input/input8
[ 13.849477] Yenta: CardBus bridge found at 0000:03:01.0 [1028:0182]
[ 13.849563] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 13.849622] Yenta: Routing CardBus interrupts to PCI
[ 13.849683] Yenta TI: socket 0000:03:01.0, mfunc 0x01111122, devctl 0x64
[ 13.975742] ieee80211_crypt: registered algorithm 'NULL'
[ 13.992588] ieee80211: 802.11 data/management/control stack, git-1.1.13
[ 13.992655] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[ 14.079588] Yenta: ISA IRQ mask 0x0cf8, PCI irq 19
[ 14.079651] Socket status: 30000006
[ 14.079707] Yenta: Raising subordinate bus# of parent bus (#03) from #04 to #07
[ 14.079788] pcmcia: parent PCI bridge I/O window: 0x6000 - 0x6fff
[ 14.079848] cs: IO port probe 0x6000-0x6fff: clean.
[ 14.080270] pcmcia: parent PCI bridge Memory window: 0xdfc00000 - 0xdfcfffff
[ 14.080332] pcmcia: parent PCI bridge Memory window: 0x88000000 - 0x8bffffff
[ 14.127002] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[ 14.127097] rtc0: alarms up to one month, y3k
[ 14.225308] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq
[ 14.225392] ipw2200: Copyright(c) 2003-2006 Intel Corporation
[ 14.225513] ACPI: PCI Interrupt 0000:03:03.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 14.250263] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
[ 14.495234] input: PS/2 Mouse as /class/input/input9
[ 14.543982] input: AlpsPS/2 ALPS GlidePoint as /class/input/input10
[ 14.575230] parport_pc 00:0c: reported by Plug and Play ACPI
[ 14.575358] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[ 15.000408] cs: IO port probe 0x100-0x3af: clean.
[ 15.002173] cs: IO port probe 0x3e0-0x4ff: clean.
[ 15.002946] cs: IO port probe 0x820-0x8ff: clean.
[ 15.003610] cs: IO port probe 0xc00-0xcf7: clean.
[ 15.004391] cs: IO port probe 0xa00-0xaff: clean.
[ 15.120357] ipw2200: Detected geography ZZD (13 802.11bg channels, 0 802.11a channels)
[ 15.120517] ACPI: PCI Interrupt 0000:00:1e.2[A] -> GSI 16 (level, low) -> IRQ 16
[ 15.120651] PCI: Setting latency timer of device 0000:00:1e.2 to 64
[ 15.949325] intel8x0_measure_ac97_clock: measured 55372 usecs
[ 15.949390] intel8x0: clocking to 48000
[ 16.768784] EXT3 FS on sda1, internal journal
[ 17.660754] kjournald starting. Commit interval 5 seconds
[ 17.661082] EXT3 FS on sda2, internal journal
[ 17.661171] EXT3-fs: mounted filesystem with ordered data mode.
[ 17.672315] kjournald starting. Commit interval 5 seconds
[ 17.672523] EXT3 FS on sda3, internal journal
[ 17.672523] EXT3-fs: mounted filesystem with ordered data mode.
[ 19.643168] fuse init (API version 7.9)
[ 25.144708] NET: Registered protocol family 10
[ 25.145255] lo: Disabled Privacy Extensions
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.26-1-686 (Debian 2.6.26-1) (waldi@debian.org) (gcc version 4.1.3 20080623 (prerelease) (Debian 4.1.2-23)) #1 SMP Wed Jul 30 20:02:15 UTC 2008
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
[ 0.000000] BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007f7d1800 (usable)
[ 0.000000] BIOS-e820: 000000007f7d1800 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0007000 (reserved)
[ 0.000000] BIOS-e820: 00000000f0008000 - 00000000f000c000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed20000 - 00000000fee10000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
[ 0.000000] 1143MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] Entering add_active_range(0, 0, 522193) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 522193
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 522193
[ 0.000000] On node 0 totalpages: 522193
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 2288 pages used for memmap
[ 0.000000] HighMem zone: 290529 pages, LIFO batch:31
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI 2.3 present.
[ 0.000000] ACPI: RSDP 000FC9B0, 0014 (r0 DELL )
[ 0.000000] ACPI: RSDT 7F7D1F90, 0040 (r1 DELL CPi R 27D50A02 ASL 61)
[ 0.000000] ACPI: FACP 7F7D2C00, 0074 (r1 DELL CPi R 27D50A02 ASL 61)
[ 0.000000] ACPI: DSDT 7F7D3800, 3C51 (r1 INT430 SYSFexxx 1001 MSFT 100000E)
[ 0.000000] ACPI: FACS 7F7E2000, 0040
[ 0.000000] ACPI: APIC 7F7D3400, 0068 (r1 DELL CPi R 27D50A02 ASL 47)
[ 0.000000] ACPI: ASF! 7F7D3000, 005B (r16 DELL CPi R 27D50A02 ASL 61)
[ 0.000000] ACPI: MCFG 7F7D33C0, 003E (r16 DELL CPi R 27D50A02 ASL 61)
[ 0.000000] ACPI: SSDT 7F7D23E6, 023E (r1 PmRef Cpu0Ist 3000 INTL 20030522)
[ 0.000000] ACPI: SSDT 7F7D220E, 01D8 (r1 PmRef Cpu0Cst 3001 INTL 20030522)
[ 0.000000] ACPI: SSDT 7F7D2013, 01FB (r1 PmRef CpuPm 3000 INTL 20030522)
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 0000000000100000
[ 0.000000] SMP: Allowing 2 CPUs, 1 hotplug CPUs
[ 0.000000] PERCPU: Allocating 37960 bytes of per cpu data
[ 0.000000] NR_CPUS: 8, nr_cpu_ids: 2
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 518113
[ 0.000000] Kernel command line: root=/dev/sda1 ro
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 1729.090 MHz processor.
[ 0.004000] Console: colour VGA+ 80x25
[ 0.004000] console [tty0] enabled
[ 0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.004000] Memory: 2060764k/2088772k available (1758k kernel code, 26712k reserved, 743k data, 244k init, 1171268k highmem)
[ 0.004000] virtual kernel memory layout:
[ 0.004000] fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB)
[ 0.004000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.004000] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 0.004000] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 0.004000] .init : 0xc0379000 - 0xc03b6000 ( 244 kB)
[ 0.004000] .data : 0xc02b78eb - 0xc0371620 ( 743 kB)
[ 0.004000] .text : 0xc0100000 - 0xc02b78eb (1758 kB)
[ 0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.084136] Calibrating delay using timer specific routine.. 3462.27 BogoMIPS (lpj=6924543)
[ 0.084294] Security Framework initialized
[ 0.084356] SELinux: Disabled at boot.
[ 0.084413] Capability LSM initialized
[ 0.084482] Mount-cache hash table entries: 512
[ 0.084721] Initializing cgroup subsys ns
[ 0.084782] Initializing cgroup subsys cpuacct
[ 0.084839] Initializing cgroup subsys devices
[ 0.084918] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.085006] CPU: L2 cache: 2048K
[ 0.085061] Intel machine check architecture supported.
[ 0.085122] Intel machine check reporting enabled on CPU#0.
[ 0.085191] Checking 'hlt' instruction... OK.
[ 0.101698] ACPI: Core revision 20080321
[ 0.111911] ENABLING IO-APIC IRQs
[ 0.112007] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.151862] CPU0: Intel(R) Pentium(R) M processor 1.73GHz stepping 08
[ 0.152009] Brought up 1 CPUs
[ 0.152009] Total of 1 processors activated (3462.27 BogoMIPS).
[ 0.152009] CPU0 attaching sched-domain:
[ 0.152009] domain 0: span 0
[ 0.152009] groups: 0
[ 0.152009] net_namespace: 660 bytes
[ 0.152009] Booting paravirtualized kernel on bare hardware
[ 0.152009] NET: Registered protocol family 16
[ 0.152009] ACPI: bus type pci registered
[ 0.152009] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.152009] PCI: MCFG area at e0000000 reserved in E820
[ 0.152009] PCI: Using MMCONFIG for extended config space
[ 0.152009] PCI: Using configuration type 1 for base access
[ 0.152009] Setting up standard PCI resources
[ 0.152009] ACPI: EC: Look up EC in DSDT
[ 0.175468] ACPI: SSDT 7F7D1FD0, 0043 (r1 LMPWR DELLLOM 1001 INTL 20030522)
[ 0.176011] ACPI: Interpreter enabled
[ 0.176011] ACPI: (supports S0 S3 S4 S5)
[ 0.176011] ACPI: Using IOAPIC for interrupt routing
[ 0.209451] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.210314] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
[ 0.210322] pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
[ 0.210403] pci 0000:00:1f.0: quirk: region 1080-10bf claimed by ICH6 GPIO
[ 0.211015] PCI: Transparent bridge - 0000:00:1e.0
[ 0.211123] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.211593] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT]
[ 0.232011] ACPI: PCI Interrupt Link [LNKA] (IRQs 9 10 *11)
[ 0.232357] ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7) *10
[ 0.232697] ACPI: PCI Interrupt Link [LNKC] (IRQs *9 10 11)
[ 0.233034] ACPI: PCI Interrupt Link [LNKD] (IRQs *5 7 9 10 11)
[ 0.233414] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.234060] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.234704] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.235472] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.235562] pnp: PnP ACPI init
[ 0.235622] ACPI: bus type pnp registered
[ 0.296236] pnp 00:0e: can't add resource for IO 0x57b0-0x57bb
[ 0.297182] pnp: PnP ACPI: found 15 devices
[ 0.297239] ACPI: ACPI bus type pnp unregistered
[ 0.297297] PnPBIOS: Disabled by ACPI PNP
[ 0.297587] PCI: Using ACPI for IRQ routing
[ 0.297927] hpet clockevent registered
[ 0.297934] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.298115] hpet0: 3 64-bit timers, 14318180 Hz
[ 0.299246] system 00:00: iomem range 0x0-0x9fbff could not be reserved
[ 0.299308] system 00:00: iomem range 0x9fc00-0x9ffff could not be reserved
[ 0.299371] system 00:00: iomem range 0xc0000-0xcffff could not be reserved
[ 0.299434] system 00:00: iomem range 0xe0000-0xfffff could not be reserved
[ 0.299497] system 00:00: iomem range 0x100000-0x7f7d17ff could not be reserved
[ 0.299576] system 00:00: iomem range 0x7f7d1800-0x7f7fffff could not be reserved
[ 0.299655] system 00:00: iomem range 0x7f800000-0x7fffffff could not be reserved
[ 0.299734] system 00:00: iomem range 0xfeda0000-0xfedfffff could not be reserved
[ 0.299814] system 00:00: iomem range 0xffb00000-0xffffffff could not be reserved
[ 0.299893] system 00:00: iomem range 0xfec00000-0xfec0ffff could not be reserved
[ 0.299972] system 00:00: iomem range 0xfee00000-0xfee0ffff could not be reserved
[ 0.300056] system 00:00: iomem range 0xfed20000-0xfed9ffff could not be reserved
[ 0.300135] system 00:00: iomem range 0xf0000000-0xf0003fff could not be reserved
[ 0.300214] system 00:00: iomem range 0xf0004000-0xf0004fff could not be reserved
[ 0.300294] system 00:00: iomem range 0xf0005000-0xf0005fff could not be reserved
[ 0.300373] system 00:00: iomem range 0xf0006000-0xf0006fff could not be reserved
[ 0.300453] system 00:00: iomem range 0xf0008000-0xf000bfff could not be reserved
[ 0.300533] system 00:00: iomem range 0xe0000000-0xefffffff could not be reserved
[ 0.300617] system 00:02: ioport range 0x4d0-0x4d1 has been reserved
[ 0.300678] system 00:02: ioport range 0x1000-0x1005 has been reserved
[ 0.300740] system 00:02: ioport range 0x1008-0x100f has been reserved
[ 0.300806] system 00:03: ioport range 0xf400-0xf4fe has been reserved
[ 0.300868] system 00:03: ioport range 0x1006-0x1007 has been reserved
[ 0.300930] system 00:03: ioport range 0x100a-0x1059 could not be reserved
[ 0.300992] system 00:03: ioport range 0x1060-0x107f has been reserved
[ 0.301054] system 00:03: ioport range 0x1080-0x10bf has been reserved
[ 0.301115] system 00:03: ioport range 0x10c0-0x10df has been reserved
[ 0.301177] system 00:03: ioport range 0x10e0-0x10ff has been reserved
[ 0.301245] system 00:08: ioport range 0x900-0x90f has been reserved
[ 0.301306] system 00:08: ioport range 0x910-0x91f has been reserved
[ 0.301368] system 00:08: ioport range 0x920-0x92f has been reserved
[ 0.301429] system 00:08: ioport range 0x93c-0x93f has been reserved
[ 0.302452] system 00:08: ioport range 0x940-0x97f has been reserved
[ 0.302520] system 00:0d: ioport range 0x930-0x93b has been reserved
[ 0.302585] system 00:0e: ioport range 0x7b0-0x7bb has been reserved
[ 0.302646] system 00:0e: ioport range 0x7c0-0x7df has been reserved
[ 0.302708] system 00:0e: ioport range 0xbb0-0xbbb has been reserved
[ 0.302769] system 00:0e: ioport range 0xbc0-0xbdf has been reserved
[ 0.302830] system 00:0e: ioport range 0xfb0-0xfbb has been reserved
[ 0.302894] system 00:0e: ioport range 0xfc0-0xfdf has been reserved
[ 0.302957] system 00:0e: ioport range 0x13b0-0x13bb has been reserved
[ 0.303019] system 00:0e: ioport range 0x13c0-0x13df has been reserved
[ 0.303081] system 00:0e: ioport range 0x17b0-0x17bb has been reserved
[ 0.303143] system 00:0e: ioport range 0x17c0-0x17df has been reserved
[ 0.303204] system 00:0e: ioport range 0x1bb0-0x1bbb has been reserved
[ 0.303266] system 00:0e: ioport range 0x1bc0-0x1bdf has been reserved
[ 0.303328] system 00:0e: ioport range 0x1fb0-0x1fbb has been reserved
[ 0.303390] system 00:0e: ioport range 0x1fc0-0x1fdf has been reserved
[ 0.303452] system 00:0e: ioport range 0x23b0-0x23bb has been reserved
[ 0.303514] system 00:0e: ioport range 0x23c0-0x23df has been reserved
[ 0.303576] system 00:0e: ioport range 0x27b0-0x27bb has been reserved
[ 0.303637] system 00:0e: ioport range 0x27c0-0x27df has been reserved
[ 0.303699] system 00:0e: ioport range 0x2bb0-0x2bbb has been reserved
[ 0.303761] system 00:0e: ioport range 0x2bc0-0x2bdf has been reserved
[ 0.303823] system 00:0e: ioport range 0x2fb0-0x2fbb has been reserved
[ 0.303884] system 00:0e: ioport range 0x2fc0-0x2fdf has been reserved
[ 0.303946] system 00:0e: ioport range 0x33b0-0x33bb has been reserved
[ 0.304008] system 00:0e: ioport range 0x33c0-0x33df has been reserved
[ 0.304072] system 00:0e: ioport range 0x37b0-0x37bb has been reserved
[ 0.304134] system 00:0e: ioport range 0x37c0-0x37df has been reserved
[ 0.304196] system 00:0e: ioport range 0x3bb0-0x3bbb has been reserved
[ 0.304258] system 00:0e: ioport range 0x3bc0-0x3bdf has been reserved
[ 0.304320] system 00:0e: ioport range 0x3fb0-0x3fbb has been reserved
[ 0.304382] system 00:0e: ioport range 0x3fc0-0x3fdf has been reserved
[ 0.304444] system 00:0e: ioport range 0x43b0-0x43bb has been reserved
[ 0.304507] system 00:0e: ioport range 0x43c0-0x43df has been reserved
[ 0.304568] system 00:0e: ioport range 0x47b0-0x47bb has been reserved
[ 0.304630] system 00:0e: ioport range 0x47c0-0x47df has been reserved
[ 0.304691] system 00:0e: ioport range 0x4bb0-0x4bbb has been reserved
[ 0.304754] system 00:0e: ioport range 0x4bc0-0x4bdf has been reserved
[ 0.304815] system 00:0e: ioport range 0x4fb0-0x4fbb has been reserved
[ 0.304877] system 00:0e: ioport range 0x4fc0-0x4fdf has been reserved
[ 0.304939] system 00:0e: ioport range 0x53b0-0x53bb has been reserved
[ 0.305001] system 00:0e: ioport range 0x53c0-0x53df has been reserved
[ 0.335519] PCI: region 0000:03:01.0/9 too large: 0x0000000000000000-0x0000000003ffffff
[ 0.335604] PCI: Bridge: 0000:00:1c.0
[ 0.335658] IO window: disabled.
[ 0.335717] MEM window: 0xdfd00000-0xdfdfffff
[ 0.335776] PREFETCH window: disabled.
[ 0.335842] PCI: Bus 4, cardbus bridge: 0000:03:01.0
[ 0.335899] IO window: 0x00006000-0x000060ff
[ 0.335959] IO window: 0x00006400-0x000064ff
[ 0.335981] MEM window: 0x88000000-0x8bffffff
[ 0.336042] PCI: Bridge: 0000:00:1e.0
[ 0.336098] IO window: 6000-6fff
[ 0.336156] MEM window: 0xdfc00000-0xdfcfffff
[ 0.336215] PREFETCH window: disabled.
[ 0.336300] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 0.336415] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 0.336429] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 0.336446] pci 0000:03:01.0: enabling device (0000 -> 0003)
[ 0.336508] ACPI: PCI Interrupt 0000:03:01.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 0.336641] NET: Registered protocol family 2
[ 0.336794] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.337111] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.338166] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.338860] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.338925] TCP reno registered
[ 0.339151] NET: Registered protocol family 1
[ 0.339350] checking if image is initramfs... it is
[ 0.800002] Switched to high resolution mode on CPU 0
[ 0.916988] Freeing initrd memory: 6250k freed
[ 0.917768] audit: initializing netlink socket (disabled)
[ 0.917844] type=2000 audit(1218447992.916:1): initialized
[ 0.918115] highmem bounce pool size: 64 pages
[ 0.918175] Total HugeTLB memory allocated, 0
[ 0.918323] VFS: Disk quotas dquot_6.5.1
[ 0.918411] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.918517] msgmni has been set to 1751
[ 0.918702] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 0.918782] io scheduler noop registered
[ 0.918837] io scheduler anticipatory registered
[ 0.918894] io scheduler deadline registered
[ 0.918966] io scheduler cfq registered (default)
[ 0.919036] pci 0000:00:02.0: Boot video device
[ 0.919251] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 0.919298] assign_interrupt_mode Found MSI capability
[ 0.919399] Allocate Port Service[0000:00:1c.0:pcie00]
[ 0.919446] Allocate Port Service[0000:00:1c.0:pcie02]
[ 0.919487] Allocate Port Service[0000:00:1c.0:pcie03]
[ 0.919845] isapnp: Scanning for PnP cards...
[ 1.274109] isapnp: No Plug & Play device found
[ 1.276926] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 1.277152] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.277703] 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.277901] ACPI: PCI Interrupt 0000:00:1e.3[B] -> GSI 17 (level, low) -> IRQ 17
[ 1.278017] ACPI: PCI interrupt for device 0000:00:1e.3 disabled
[ 1.279566] brd: module loaded
[ 1.279724] PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 1.284715] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.284777] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.284982] mice: PS/2 mouse device common for all mice
[ 1.285101] cpuidle: using governor ladder
[ 1.285157] cpuidle: using governor menu
[ 1.285215] No iBFT detected.
[ 1.285731] TCP cubic registered
[ 1.285786] NET: Registered protocol family 17
[ 1.285849] Using IPI No-Shortcut mode
[ 1.286041] registered taskstats version 1
[ 1.286370] Freeing unused kernel memory: 244k freed
[ 1.290542] input: AT Translated Set 2 keyboard as /class/input/input0
[ 1.379638] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3])
[ 1.379898] ACPI: ACPI0007:00 is registered as cooling_device0
[ 1.379959] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 1.383049] ACPI: LNXTHERM:01 is registered as thermal_zone0
[ 1.384700] ACPI: Thermal Zone [THM] (75 C)
[ 1.985528] ACPI: ACPI Dock Station Driver
[ 2.019262] tg3.c:v3.92.1 (June 9, 2008)
[ 2.019353] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 2.019471] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 2.042529] eth0: Tigon3 [partno(BCM95751) rev 4001 PHY(5750)] (PCI Express) 10/100/1000Base-T Ethernet 00:15:c5:0b:fb:92
[ 2.042621] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
[ 2.042700] eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[ 2.074088] usbcore: registered new interface driver usbfs
[ 2.074184] usbcore: registered new interface driver hub
[ 2.074272] usbcore: registered new device driver usb
[ 2.075432] USB Universal Host Controller Interface driver v3.0
[ 2.075535] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 2.075657] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 2.075661] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 2.075852] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[ 2.075963] uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000bf80
[ 2.076115] usb usb1: configuration #1 chosen from 1 choice
[ 2.076205] hub 1-0:1.0: USB hub found
[ 2.076274] hub 1-0:1.0: 2 ports detected
[ 2.180154] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.180223] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.180302] usb usb1: Product: UHCI Host Controller
[ 2.180360] usb usb1: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[ 2.180419] usb usb1: SerialNumber: 0000:00:1d.0
[ 2.180537] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 17
[ 2.180659] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 2.180663] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 2.180745] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[ 2.180858] uhci_hcd 0000:00:1d.1: irq 17, io base 0x0000bf60
[ 2.180999] usb usb2: configuration #1 chosen from 1 choice
[ 2.181088] hub 2-0:1.0: USB hub found
[ 2.181148] hub 2-0:1.0: 2 ports detected
[ 2.212100] Uniform Multi-Platform E-IDE driver
[ 2.212165] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 2.284128] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.284199] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.284277] usb usb2: Product: UHCI Host Controller
[ 2.284335] usb usb2: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[ 2.284395] usb usb2: SerialNumber: 0000:00:1d.1
[ 2.284500] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 2.284620] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 2.284625] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 2.284706] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[ 2.284816] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000bf40
[ 2.284962] usb usb3: configuration #1 chosen from 1 choice
[ 2.285051] hub 3-0:1.0: USB hub found
[ 2.285111] hub 3-0:1.0: 2 ports detected
[ 2.368939] Marking TSC unstable due to: TSC halts in idle.
[ 2.506517] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.506517] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.506517] usb usb3: Product: UHCI Host Controller
[ 2.506517] usb usb3: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[ 2.506517] usb usb3: SerialNumber: 0000:00:1d.2
[ 2.506517] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 19
[ 2.506517] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[ 2.506517] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 2.506517] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[ 2.506517] uhci_hcd 0000:00:1d.3: irq 19, io base 0x0000bf20
[ 2.506517] usb usb4: configuration #1 chosen from 1 choice
[ 2.506517] hub 4-0:1.0: USB hub found
[ 2.506517] hub 4-0:1.0: 2 ports detected
[ 2.607317] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.607317] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.607317] usb usb4: Product: UHCI Host Controller
[ 2.607317] usb usb4: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[ 2.607317] usb usb4: SerialNumber: 0000:00:1d.3
[ 2.607317] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 16 (level, low) -> IRQ 16
[ 2.607317] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 2.607317] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 2.607317] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
[ 2.607317] ehci_hcd 0000:00:1d.7: debug port 1
[ 2.607317] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 2.607317] ehci_hcd 0000:00:1d.7: irq 16, io mem 0xffa80800
[ 2.618012] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 2.618012] usb usb5: configuration #1 chosen from 1 choice
[ 2.618012] hub 5-0:1.0: USB hub found
[ 2.618012] hub 5-0:1.0: 8 ports detected
[ 2.720915] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.720915] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.720915] usb usb5: Product: EHCI Host Controller
[ 2.720915] usb usb5: Manufacturer: Linux 2.6.26-1-686 ehci_hcd
[ 2.720915] usb usb5: SerialNumber: 0000:00:1d.7
[ 2.720915] SCSI subsystem initialized
[ 2.720915] libata version 3.00 loaded.
[ 2.720915] ahci 0000:00:1f.2: version 3.0
[ 2.720915] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level, low) -> IRQ 17
[ 2.720915] ACPI: PCI interrupt for device 0000:00:1f.2 disabled
[ 2.720915] ahci: probe of 0000:00:1f.2 failed with error -22
[ 2.720915] ata_piix 0000:00:1f.2: version 2.12
[ 2.720915] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level, low) -> IRQ 17
[ 2.720915] ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
[ 2.796052] Clocksource tsc unstable (delta = -343998974 ns)
[ 2.796145] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 2.796307] scsi0 : ata_piix
[ 2.796470] scsi1 : ata_piix
[ 2.798538] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xbfa0 irq 14
[ 2.798602] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xbfa8 irq 15
[ 2.961650] ata1.00: ATA-6: ST960822A, 8.03, max UDMA/100
[ 2.961716] ata1.00: 117210240 sectors, multi 8: LBA48
[ 2.961775] ata1.00: applying bridge limits
[ 2.978108] ata1.00: configured for UDMA/100
[ 3.120029] usb 3-2: new low speed USB device using uhci_hcd and address 2
[ 3.156466] ata2.00: ATAPI: TSSTcorpCD-RW/DVD-ROM TSL462C, DE01, max UDMA/33
[ 3.188403] ata2.00: configured for UDMA/33
[ 3.188576] scsi 0:0:0:0: Direct-Access ATA ST960822A 8.03 PQ: 0 ANSI: 5
[ 3.189368] scsi 1:0:0:0: CD-ROM TSSTcorp CDRW/DVD TSL462C DE01 PQ: 0 ANSI: 5
[ 3.220787] Driver 'sd' needs updating - please use bus_type methods
[ 3.220968] sd 0:0:0:0: [sda] 117210240 512-byte hardware sectors (60012 MB)
[ 3.221050] sd 0:0:0:0: [sda] Write Protect is off
[ 3.221108] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.221146] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.221296] sd 0:0:0:0: [sda] 117210240 512-byte hardware sectors (60012 MB)
[ 3.221377] sd 0:0:0:0: [sda] Write Protect is off
[ 3.221435] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.221473] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.221557] sda:<4>Driver 'sr' needs updating - please use bus_type methods
[ 3.296317] usb 3-2: configuration #1 chosen from 1 choice
[ 3.296317] usb 3-2: New USB device found, idVendor=046d, idProduct=c024
[ 3.300062] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3.300124] usb 3-2: Product: USB-PS/2 Optical Mouse
[ 3.300183] usb 3-2: Manufacturer: B16_b_02
[ 3.300862] sda1 sda2 sda3
[ 3.301128] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.303797] sr0: scsi3-mmc drive: 10x/24x writer cd/rw xa/form2 cdda tray
[ 3.303860] Uniform CD-ROM driver Revision: 3.20
[ 3.303977] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 3.329877] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 3.329967] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 3.350467] usbcore: registered new interface driver hiddev
[ 3.364414] input: B16_b_02 USB-PS/2 Optical Mouse as /class/input/input1
[ 3.368980] input,hidraw0: USB HID v1.10 Mouse [B16_b_02 USB-PS/2 Optical Mouse] on usb-0000:00:1d.2-2
[ 3.369206] usbcore: registered new interface driver usbhid
[ 3.369267] usbhid: v2.6:USB HID core driver
[ 3.542513] device-mapper: uevent: version 1.0.3
[ 3.543881] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
[ 3.593472] kjournald starting. Commit interval 5 seconds
[ 3.593472] EXT3-fs: mounted filesystem with ordered data mode.
[ 10.419990] udevd version 125 started
[ 10.849251] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[ 11.291541] Linux agpgart interface v0.103
[ 11.303058] agpgart: Detected an Intel 915GM Chipset.
[ 11.303453] agpgart: Detected 7932K stolen memory.
[ 11.320493] agpgart: AGP aperture is 256M @ 0xc0000000
[ 11.763984] ACPI: AC Adapter [AC] (on-line)
[ 12.172640] ACPI: Battery Slot [BAT0] (battery present)
[ 12.172800] ACPI: Battery Slot [BAT1] (battery absent)
[ 12.172959] input: Lid Switch as /class/input/input2
[ 12.184586] ACPI: Lid Switch [LID]
[ 12.184708] input: Power Button (CM) as /class/input/input3
[ 12.208069] ACPI: Power Button (CM) [PBTN]
[ 12.208280] input: Sleep Button (CM) as /class/input/input4
[ 12.236045] ACPI: Sleep Button (CM) [SBTN]
[ 12.898301] ACPI: \_SB_.PCI0.IDE0.SEC0.MAST: found ejectable bay
[ 12.898307] ACPI: \_SB_.PCI0.IDE0.SEC0.MAST: Adding notify handler
[ 12.898336] ACPI: Error installing bay notify handler
[ 12.941979] input: Video Bus as /class/input/input5
[ 12.972069] ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
[ 12.972670] input: Video Bus as /class/input/input6
[ 13.004071] ACPI: Video Device [VID1] (multi-head: yes rom: no post: no)
[ 13.004299] input: Video Bus as /class/input/input7
[ 13.036058] ACPI: Video Device [VID2] (multi-head: yes rom: no post: no)
[ 13.406125] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
[ 13.406280] iTCO_wdt: Found a ICH6-M TCO device (Version=2, TCOBASE=0x1060)
[ 13.406372] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 13.523058] ACPI: PCI Interrupt 0000:00:1e.3[B] -> GSI 17 (level, low) -> IRQ 17
[ 13.523195] PCI: Setting latency timer of device 0000:00:1e.3 to 64
[ 13.541115] intel_rng: FWH not detected
[ 13.624055] MC'97 1 converters and GPIO not ready (0xff00)
[ 13.737474] Yenta: CardBus bridge found at 0000:03:01.0 [1028:0182]
[ 13.737566] PCI: Bus 4, cardbus bridge: 0000:03:01.0
[ 13.737624] IO window: 0x00006000-0x000060ff
[ 13.737684] IO window: 0x00006400-0x000064ff
[ 13.737744] PREFETCH window: 0x8c000000-0x8c3fffff
[ 13.737805] MEM window: 0x88000000-0x8bffffff
[ 13.737869] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 13.737928] Yenta: Routing CardBus interrupts to PCI
[ 13.737990] Yenta TI: socket 0000:03:01.0, mfunc 0x01111122, devctl 0x64
[ 13.821363] input: PC Speaker as /class/input/input8
[ 13.831578] ieee80211_crypt: registered algorithm 'NULL'
[ 13.835332] ieee80211: 802.11 data/management/control stack, git-1.1.13
[ 13.835401] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[ 13.840313] Error: Driver 'pcspkr' is already registered, aborting...
[ 13.876740] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq
[ 13.876825] ipw2200: Copyright(c) 2003-2006 Intel Corporation
[ 13.910509] Error: Driver 'pcspkr' is already registered, aborting...
[ 13.968844] Yenta: ISA IRQ mask 0x0cf8, PCI irq 19
[ 13.968909] Socket status: 30000006
[ 13.968965] Yenta: Raising subordinate bus# of parent bus (#03) from #04 to #07
[ 13.969046] pcmcia: parent PCI bridge I/O window: 0x6000 - 0x6fff
[ 13.969106] cs: IO port probe 0x6000-0x6fff: clean.
[ 13.969562] pcmcia: parent PCI bridge Memory window: 0xdfc00000 - 0xdfcfffff
[ 13.978457] ACPI: PCI Interrupt 0000:03:03.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 13.978629] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
[ 13.978729] firmware: requesting ipw2200-bss.fw
[ 14.128905] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[ 14.128992] rtc0: alarms up to one month, y3k
[ 14.476472] input: PS/2 Mouse as /class/input/input9
[ 14.529409] input: AlpsPS/2 ALPS GlidePoint as /class/input/input10
[ 14.560345] parport_pc 00:0c: reported by Plug and Play ACPI
[ 14.560474] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[ 15.225156] cs: IO port probe 0x100-0x3af: clean.
[ 15.226919] cs: IO port probe 0x3e0-0x4ff: clean.
[ 15.227694] cs: IO port probe 0x820-0x8ff: clean.
[ 15.228376] cs: IO port probe 0xc00-0xcf7: clean.
[ 15.229179] cs: IO port probe 0xa00-0xaff: clean.
[ 15.372694] ipw2200: Detected geography ZZD (13 802.11bg channels, 0 802.11a channels)
[ 15.372876] ACPI: PCI Interrupt 0000:00:1e.2[A] -> GSI 16 (level, low) -> IRQ 16
[ 15.373970] PCI: Setting latency timer of device 0000:00:1e.2 to 64
[ 16.200032] intel8x0_measure_ac97_clock: measured 55353 usecs
[ 16.200098] intel8x0: clocking to 48000
[ 17.062318] EXT3 FS on sda1, internal journal
[ 17.274174] vboxdrv: Trying to deactivate the NMI watchdog permanently...
[ 17.274178] vboxdrv: Successfully done.
[ 17.274180] vboxdrv: Found 1 processor cores.
[ 17.274183] vboxdrv: fAsync=0 u64DiffCores=1.
[ 17.274219] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[ 17.274301] vboxdrv: Successfully loaded version 1.6.2_OSE (interface 0x00070002).
[ 17.994822] kjournald starting. Commit interval 5 seconds
[ 17.995050] EXT3 FS on sda2, internal journal
[ 17.996029] EXT3-fs: mounted filesystem with ordered data mode.
[ 18.007226] kjournald starting. Commit interval 5 seconds
[ 18.008262] EXT3 FS on sda3, internal journal
[ 18.008350] EXT3-fs: mounted filesystem with ordered data mode.
[ 20.034089] fuse init (API version 7.9)
[ 25.695976] NET: Registered protocol family 10
[ 25.696583] lo: Disabled Privacy Extensions
[ 27.125455] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 28.401303] Bridge firewalling registered
[ 28.402688] bridge0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
[ 28.459309] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 28.492065] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 28.822123] Netfilter messages via NETLINK v0.30.
[ 28.824109] ctnetlink v0.93: registering with nfnetlink.
[ 29.301800] tun: Universal TUN/TAP device driver, 1.6
[ 29.301800] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 30.372647] device vbox0 entered promiscuous mode
[ 30.372647] bridge0: port 1(vbox0) entering learning state
[ 31.372031] bridge0: topology change detected, propagating
[ 31.372094] bridge0: port 1(vbox0) entering forwarding state
[ 39.168009] bridge0: no IPv6 routers present
[ 39.608014] vbox0: no IPv6 routers present
[ 40.135995] Bluetooth: Core ver 2.11
[ 40.137362] NET: Registered protocol family 31
[ 40.137426] Bluetooth: HCI device and connection manager initialized
[ 40.137487] Bluetooth: HCI socket layer initialized
[ 40.151425] Bluetooth: L2CAP ver 2.9
[ 40.151489] Bluetooth: L2CAP socket layer initialized
[ 40.249391] Bluetooth: RFCOMM socket layer initialized
[ 40.249466] Bluetooth: RFCOMM TTY layer initialized
[ 40.249523] Bluetooth: RFCOMM ver 1.8
[ 41.665663] lp0: using parport0 (interrupt-driven).
[ 41.692565] ppdev: user-space parallel port driver
[ 46.495593] [drm] Initialized drm 1.1.0 20060810
[ 46.500072] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 46.500084] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 46.500167] [drm] Initialized i915 1.6.0 20060119 on minor 0
Reply to: