Bug#494384: linux-image-2.6.26-1-openvz-686: Fails to load nfsd module
Package: linux-image-2.6.26-1-openvz-686
Version: 2.6.26-1
Severity: normal
Hello,
I upgraded from 2.6.25-2 to 2.6.26-1-openvz-686.
After reboot, the nfsd module fails to load with this error message:
FATAL: Error inserting nfsd (/lib/modules/2.6.26-1-openvz-686/kernel/fs/nfsd/nfsd.ko): Cannot allocate memory
Not starting NFS kernel daemon: no support in current kernel.
nfsd loads without error if I boot the 2.6.26-1-686 kernel instead.
Is there a way to use both nfs and openvz?
-- Package-specific info:
** Version:
Linux version 2.6.26-1-openvz-686 (Debian 2.6.26-1) (waldi@debian.org) (gcc version 4.1.3 20080623 (prerelease) (Debian 4.1.2-23)) #1 SMP Wed Jul 30 22:23:50 UTC 2008
** Command line:
root=/dev/mapper/crypt_sda2 ro vdso=1
** Not tainted
** Kernel log:
[ 2.900441] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.900555] sd 0:0:1:0: [sdb] 1465149168 512-byte hardware sectors (750156 MB)
[ 2.900646] sd 0:0:1:0: [sdb] Write Protect is off
[ 2.900701] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 2.900728] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.900857] sd 0:0:1:0: [sdb] 1465149168 512-byte hardware sectors (750156 MB)
[ 2.900948] sd 0:0:1:0: [sdb] Write Protect is off
[ 2.901002] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 2.901030] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.901114] sdb:<4>Driver 'sr' needs updating - please use bus_type methods
[ 2.921521] sdb1 sdb2 sdb3 < sdb5 sdb6 >
[ 2.940217] sd 0:0:1:0: [sdb] Attached SCSI disk
[ 2.942392] sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
[ 2.942455] Uniform CD-ROM driver Revision: 3.20
[ 2.942571] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 2.963647] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 2.963729] sd 0:0:1:0: Attached scsi generic sg1 type 0
[ 2.963804] sr 1:0:0:0: Attached scsi generic sg2 type 5
[ 3.342985] device-mapper: uevent: version 1.0.3
[ 3.343830] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
[ 3.644121] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00301bba000073d4]
[ 11.559988] kjournald starting. Commit interval 5 seconds
[ 11.559988] EXT3-fs: mounted filesystem with ordered data mode.
[ 13.416134] Linux agpgart interface v0.103
[ 13.430519] agpgart: Detected an Intel 915GM Chipset.
[ 13.431041] agpgart: Detected 7932K stolen memory.
[ 13.448035] agpgart: AGP aperture is 256M @ 0xc0000000
[ 13.523279] input: Power Button (FF) as /class/input/input1
[ 13.548997] ACPI: Power Button (FF) [PWRF]
[ 13.549113] input: Power Button (CM) as /class/input/input2
[ 13.576041] ACPI: Power Button (CM) [PWRB]
[ 14.201225] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
[ 14.201363] iTCO_wdt: Found a ICH6-M TCO device (Version=2, TCOBASE=0x0460)
[ 14.201446] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 14.248018] intel_rng: FWH not detected
[ 14.336099] ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 19
[ 14.490205] input: PC Speaker as /class/input/input3
[ 14.534647] Error: Driver 'pcspkr' is already registered, aborting...
[ 14.546326] ACPI: PCI Interrupt 0000:03:09.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 14.546452] snd-ca0106: Model 3041 Rev 00000000 Serial 30411297
[ 16.180603] EXT3 FS on dm-0, internal journal
[ 16.904931] loop: module loaded
[ 17.113974] it87: Found IT8712F chip at 0x290, revision 6
[ 17.114104] it87 it87.656: Detected broken BIOS defaults, disabling PWM interface
[ 62.476902] kjournald starting. Commit interval 5 seconds
[ 62.476902] EXT3 FS on sda1, internal journal
[ 62.476902] EXT3-fs: mounted filesystem with ordered data mode.
[ 62.516004] kjournald starting. Commit interval 5 seconds
[ 62.516004] EXT3 FS on dm-10, internal journal
[ 62.516004] EXT3-fs: mounted filesystem with ordered data mode.
[ 62.548002] kjournald starting. Commit interval 5 seconds
[ 62.548002] EXT3 FS on dm-11, internal journal
[ 62.548002] EXT3-fs: mounted filesystem with ordered data mode.
[ 62.596004] kjournald starting. Commit interval 5 seconds
[ 62.608271] EXT3 FS on dm-12, internal journal
[ 62.608348] EXT3-fs: mounted filesystem with ordered data mode.
[ 62.639837] kjournald starting. Commit interval 5 seconds
[ 62.639837] EXT3 FS on dm-14, internal journal
[ 62.639837] EXT3-fs: mounted filesystem with ordered data mode.
[ 62.673521] kjournald starting. Commit interval 5 seconds
[ 62.680206] EXT3 FS on dm-13, internal journal
[ 62.680282] EXT3-fs: mounted filesystem with ordered data mode.
[ 62.704002] kjournald starting. Commit interval 5 seconds
[ 62.716129] EXT3 FS on dm-2, internal journal
[ 62.716204] EXT3-fs: mounted filesystem with ordered data mode.
[ 62.761053] Adding 5999240k swap on /dev/mapper/sda3_crypt. Priority:-1 extents:1 across:5999240k
[ 64.392002] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 64.475762] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 64.620867] nf_nat_ftp: Unknown parameter `modprobe'
[ 64.757302] NET: Registered protocol family 10
[ 64.788208] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 65.218203] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 67.130362] r8169: eth1: link up
[ 67.130423] r8169: eth1: link up
[ 68.100264] tg3: eth0: Link is up at 1000 Mbps, full duplex.
[ 68.100345] tg3: eth0: Flow control is on for TX and on for RX.
[ 68.100622] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 73.467750] RPC: Registered udp transport module.
[ 73.467829] RPC: Registered tcp transport module.
[ 73.581266] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 77.448009] eth1: no IPv6 routers present
[ 78.852008] eth0: no IPv6 routers present
[ 84.340020] Marking TSC unstable due to: cpufreq changes.
[ 84.712018] Clocksource tsc unstable (delta = -189014139 ns)
[ 85.591366] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 85.636507] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 85.932698] device eth0 entered promiscuous mode
[ 85.934972] device eth1 entered promiscuous mode
[ 89.105011] warning: `ntpd' uses 32-bit capabilities (legacy support in use)
[ 1179.460028] usb 4-1: new low speed USB device using uhci_hcd and address 2
[ 1179.636035] usb 4-1: configuration #1 chosen from 1 choice
[ 1179.636035] usb 4-1: New USB device found, idVendor=046d, idProduct=c03e
[ 1179.636035] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 1179.636035] usb 4-1: Product: USB-PS/2 Optical Mouse
[ 1179.636035] usb 4-1: Manufacturer: Logitech
[ 1179.766386] usbcore: registered new interface driver hiddev
[ 1179.779044] input: Logitech USB-PS/2 Optical Mouse as /class/input/input4
[ 1179.779044] input,hidraw0: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.3-1
[ 1179.780125] usbcore: registered new interface driver usbhid
[ 1179.780182] usbhid: v2.6:USB HID core driver
** Loaded modules:
Module Size Used by
usbhid 36736 0
hid 33952 1 usbhid
ff_memless 5160 1 usbhid
vzethdev 9120 0
vznetdev 14500 0
simfs 4756 0
vzdquota 32796 0 [permanent]
vzmon 22856 2 vzethdev,vznetdev
vzdev 3624 4 vzethdev,vznetdev,vzdquota,vzmon
xt_length 2528 0
ipt_ttl 2368 0
xt_tcpmss 2752 0
iptable_mangle 4640 0
xt_multiport 3584 0
xt_limit 2948 0
xt_dscp 3136 0
ipt_REJECT 3552 0
video 17168 0
output 3680 1 video
ac 4032 0
battery 7040 0
acpi_cpufreq 7564 0
cpufreq_ondemand 7244 1
cpufreq_userspace 4420 0
cpufreq_powersave 2624 0
cpufreq_stats 4640 0
freq_table 5088 3 acpi_cpufreq,cpufreq_ondemand,cpufreq_stats
cpufreq_conservative 6728 0
auth_rpcgss 34752 0
exportfs 4832 0
lockd 55016 0
nfs_acl 3680 0
sunrpc 163904 6 auth_rpcgss,lockd,nfs_acl
ipt_MASQUERADE 2784 1
iptable_nat 7172 1
xt_TCPMSS 4448 1
xt_conntrack 4256 36
xt_tcpudp 3584 189
ip6t_LOG 6276 1
ipt_LOG 5924 39
ip6table_filter 4256 1
ip6_tables 12240 2 ip6t_LOG,ip6table_filter
ipv6 242016 25 vzmon
iptable_filter 4288 1
nf_nat 16500 2 ipt_MASQUERADE,iptable_nat
nf_conntrack_ftp 7684 0
nf_conntrack_ipv4 17424 39 iptable_nat,nf_nat
nf_conntrack 65224 5 iptable_nat,xt_conntrack,nf_nat,nf_conntrack_ftp,nf_conntrack_ipv4
ip_tables 11056 3 iptable_mangle,iptable_nat,iptable_filter
x_tables 14404 16 xt_length,ipt_ttl,xt_tcpmss,xt_multiport,xt_limit,xt_dscp,ipt_REJECT,ipt_MASQUERADE,iptable_nat,xt_TCPMSS,xt_conntrack,xt_tcpudp,ip6t_LOG,ipt_LOG,ip6_tables,ip_tables
ext2 55144 1
it87 18544 0
hwmon_vid 3488 1 it87
eeprom 6000 0
sbp2 19724 0
loop 13516 0
snd_ca0106 28352 0
snd_rawmidi 19328 1 snd_ca0106
snd_seq_device 7148 1 snd_rawmidi
snd_ac97_codec 89252 1 snd_ca0106
pcspkr 3200 0
snd_pcm 63460 2 snd_ca0106,snd_ac97_codec
snd_timer 18568 1 snd_pcm
snd 46404 6 snd_ca0106,snd_rawmidi,snd_seq_device,snd_ac97_codec,snd_pcm,snd_timer
soundcore 7136 1 snd
ac97_bus 2496 1 snd_ac97_codec
snd_page_alloc 8648 2 snd_ca0106,snd_pcm
i2c_i801 8688 0
i2c_core 20596 2 eeprom,i2c_i801
rng_core 4708 0
iTCO_wdt 10276 0
button 6832 0
intel_agp 23236 1
agpgart 29576 1 intel_agp
evdev 8736 0
ext3 105864 8
jbd 40148 1 ext3
mbcache 7876 2 ext2,ext3
cbc 4032 9
dm_crypt 11940 1
dm_mirror 15872 0
dm_log 9220 1 dm_mirror
dm_snapshot 15108 0
dm_mod 46984 35 dm_crypt,dm_mirror,dm_log,dm_snapshot
sg 27732 0
sr_mod 14212 0
cdrom 30976 1 sr_mod
sd_mod 22968 7
ata_generic 5444 0
ahci 24008 0
ata_piix 15012 5
libata 141344 3 ata_generic,ahci,ata_piix
scsi_mod 130220 5 sbp2,sg,sr_mod,sd_mod,libata
dock 9040 1 libata
ide_pci_generic 4676 0 [permanent]
ide_core 93492 1 ide_pci_generic
ohci1394 26000 0
ieee1394 76600 2 sbp2,ohci1394
ehci_hcd 29420 0
uhci_hcd 19504 0
usbcore 119216 4 usbhid,ehci_hcd,uhci_hcd
r8169 24612 0
tg3 85700 0
thermal 15996 0
processor 33540 2 acpi_cpufreq,thermal
fan 4932 0
thermal_sys 11624 4 video,thermal,processor,fan
aes_i586 8512 18
crypto_blkcipher 16004 11 cbc,dm_crypt
aes_generic 30024 1 aes_i586
sha256_generic 12128 0
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller [8086:2590] (rev 04)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Device [1297:3041]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
Kernel modules: intel-agp
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller [8086:2592] (rev 04)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Device [1297:3041]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 0: Memory at d0380000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at da00 [size=8]
Region 2: Memory at c0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at d0400000 (32-bit, non-prefetchable) [size=256K]
Capabilities: <access denied>
Kernel modules: intelfb
00:02.1 Display controller [0380]: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller [8086:2792] (rev 04)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Device [1297:3041]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at d0300000 (32-bit, non-prefetchable) [size=512K]
Capabilities: <access denied>
00:1c.0 PCI bridge [0604]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 [8086:2660] (rev 04)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: d0000000-d00fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.2 PCI bridge [0604]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 3 [8086:2664] (rev 04)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: d0100000-d01fffff
Prefetchable memory behind bridge: 0000000080000000-00000000800fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1d.0 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 [8086:2658] (rev 04)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Device [1297:3041]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at db00 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 [8086:2659] (rev 04)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Device [1297:3041]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at dd00 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 [8086:265a] (rev 04)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Device [1297:3041]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at d800 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.3 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 [8086:265b] (rev 04)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Device [1297:3041]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at d900 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller [8086:265c] (rev 04) (prog-if 20)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Device [1297:3041]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at d0440000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev d4) (prog-if 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: d0200000-d02fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge [8086:2641] (rev 04)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Kernel modules: intel-rng, iTCO_wdt
00:1f.2 IDE interface [0101]: Intel Corporation 82801FBM (ICH6M) SATA Controller [8086:2653] (rev 04) (prog-if 80 [Master])
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Device [1297:3041]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at f000 [size=16]
Capabilities: <access denied>
Kernel driver in use: ata_piix
Kernel modules: ata_piix, ahci
00:1f.3 SMBus [0c05]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller [8086:266a] (rev 04)
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 0500 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801
01:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM5789 Gigabit Ethernet PCI Express [14e4:169d] (rev 11)
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Device [1297:fd11]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d0000000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at <ignored> [disabled]
Capabilities: <access denied>
Kernel driver in use: tg3
Kernel modules: tg3
02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 01)
Subsystem: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 221
Region 0: I/O ports at b000 [size=256]
Region 2: Memory at d0120000 (64-bit, non-prefetchable) [size=4K]
[virtual] Expansion ROM at 80000000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: r8169
Kernel modules: r8169
03:09.0 Multimedia audio controller [0401]: Creative Labs SB Audigy LS [1102:0007]
Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer Device [1297:3041]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at c000 [size=32]
Capabilities: <access denied>
Kernel driver in use: CA0106
Kernel modules: snd-ca0106
03:0a.0 FireWire (IEEE 1394) [0c00]: VIA Technologies, Inc. IEEE 1394 Host Controller [1106:3044] (rev 80) (prog-if 10)
Subsystem: VIA Technologies, Inc. IEEE 1394 Host Controller [1106:3044]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (8000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at d0200000 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at c100 [size=128]
Capabilities: <access denied>
Kernel driver in use: ohci1394
Kernel modules: ohci1394
-- System Information:
Debian Release: lenny/sid
APT prefers testing
APT policy: (990, 'testing'), (500, 'unstable'), (500, 'stable'), (1, 'experimental')
Architecture: i386 (i686)
Kernel: Linux 2.6.26-1-openvz-686 (SMP w/1 CPU core)
Locale: LANG=de_DE.UTF-8, LC_CTYPE=de_DE.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.26-1-openvz-686 depends on:
ii debconf [debconf-2.0] 1.5.22 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92e tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
ii vzctl 3.0.22-9 server virtualization solution - c
Versions of packages linux-image-2.6.26-1-openvz-686 recommends:
ii libc6-i686 2.7-13 GNU C Library: Shared libraries [i
Versions of packages linux-image-2.6.26-1-openvz-686 suggests:
ii grub 0.97-44 GRand Unified Bootloader (Legacy v
pn linux-doc-2.6.26 <none> (no description available)
-- debconf information:
linux-image-2.6.26-1-openvz-686/preinst/elilo-initrd-2.6.26-1-openvz-686: true
linux-image-2.6.26-1-openvz-686/postinst/kimage-is-a-directory:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.26-1-openvz-686/postinst/old-dir-initrd-link-2.6.26-1-openvz-686: true
linux-image-2.6.26-1-openvz-686/postinst/depmod-error-initrd-2.6.26-1-openvz-686: false
linux-image-2.6.26-1-openvz-686/prerm/removing-running-kernel-2.6.26-1-openvz-686: true
linux-image-2.6.26-1-openvz-686/preinst/lilo-initrd-2.6.26-1-openvz-686: true
linux-image-2.6.26-1-openvz-686/postinst/old-initrd-link-2.6.26-1-openvz-686: true
linux-image-2.6.26-1-openvz-686/postinst/bootloader-test-error-2.6.26-1-openvz-686:
linux-image-2.6.26-1-openvz-686/preinst/abort-overwrite-2.6.26-1-openvz-686:
linux-image-2.6.26-1-openvz-686/postinst/old-system-map-link-2.6.26-1-openvz-686: true
linux-image-2.6.26-1-openvz-686/postinst/bootloader-error-2.6.26-1-openvz-686:
linux-image-2.6.26-1-openvz-686/postinst/create-kimage-link-2.6.26-1-openvz-686: true
linux-image-2.6.26-1-openvz-686/preinst/lilo-has-ramdisk:
linux-image-2.6.26-1-openvz-686/postinst/depmod-error-2.6.26-1-openvz-686: false
linux-image-2.6.26-1-openvz-686/preinst/abort-install-2.6.26-1-openvz-686:
linux-image-2.6.26-1-openvz-686/preinst/initrd-2.6.26-1-openvz-686:
linux-image-2.6.26-1-openvz-686/preinst/overwriting-modules-2.6.26-1-openvz-686: true
linux-image-2.6.26-1-openvz-686/prerm/would-invalidate-boot-loader-2.6.26-1-openvz-686: true
linux-image-2.6.26-1-openvz-686/preinst/failed-to-move-modules-2.6.26-1-openvz-686:
linux-image-2.6.26-1-openvz-686/preinst/bootloader-initrd-2.6.26-1-openvz-686: true
Reply to: