Bug#493479: linux-image-2.6.26-1-amd64: 2.6.26-1 freezes soon after boot, a regression compared to 2.6.25-2
Package: linux-image-2.6.26-1-amd64
Version: 2.6.26-1
Severity: critical
Justification: breaks the whole system
[NB: I refer below to self-compiled kernels a bit, but this report IS
against the stock kernel.]
I saw that there is a push to get 2.6.26 into Lenny, so when
linux-source-2.6.26_2.6.26-1_all.deb became available I decided I should
try building kernels with it for my desktop and file server machines.
I have carefully crafted '.config' files for each machine, and only install
the Debian stock kernels as safety backups (in case of some major oversight
on my part). I use 'make oldconfig' to ease the process of deciding about
config changes with each kernel release.
I have 3 machines running AMD Athlon 64 X2 dual core CPUs. One is a
desktop machine, and the other 2 are recently-built, less-powerful machines
I will be using as servers.
On my desktop machine (running Sid) -- most of the kernel-relevant hardware
located on a Gigabyte GA-M59SLI-S5 motherboard -- the new custom kernel
built without error and ran perfectly.
On my fileserver machine (running Lenny) -- with a much different ECS
AMD790GM-M2 motherboard -- the custom kernel built without error, but
freezes soon after boot: no panic/oops/segfault, no error message of any
kind.
I assumed I made a config error, because added new configs for RAID+LVM for
two 500GB drives I just purchased (and tested with 'badblocks') for a RAID1
array. After several attempts to recompile, making slight, then drastic,
config changes hoping to just get it to boot, I decided to try the stock
kernel.
The stock kernel experiences the same freeze, without error messages.
When I discovered that, I wanted to be helpful and try to pin down a
specific configuration or other cause for the freeze. I know that the
hardware is perfectly functional: I am using it to write this bug report,
and it is running my own custom kernel built from Debian 2.6.25-7 sources.
The failure of the 2.6.26-1 kernel is some sort of regression against this
hardware. (See below for the output of 'lspci -vv -nn'.)
On a personal note, I am currently on the path to learning how to program
for the Linux platform, and hope to learn enough to be able to package my
own self-written software for Debian. Unfortunately, my background is with
another OS, and I have not (yet) learned how to track and pin down this
sort of bug using Linux development tools. If you can give me clear enough
instructions, however, I am more than willing to dig into the source code
to try to locate the bug. Possibly some well placed "printk" calls in
certain source files would help?
Without any of the proper debugging skills, I did attempt to learn the
cause of the freeze. I doubt that anything I tried will be useful to you
folks, but I will report my findings Just In Case (TM):
1. Using GRUB to edit to "kernel" line, I added
"debug earlyprink=vga initcall_debug loglevel=7" to my boot parameter
list. Other than the "initcall_debug" parameter, I didn't notice much
effect -- I was hoping for some telltale message that would make it clear
what function was starting, but not finishing, when the system was locking
up.
A) On the stock kernel, each "calling" line was followed with a line
reporting a return value of 0, until the last call. The last two lines of
output on the screen were:
calling inet_init+0x0/0x34a
NET: Registered protocol family 2
B) Think that the networking drivers were causing the freeze, I took my
last working '.config' for 2.6.25-7 and disabled CONFIG_NET, then ran 'make
oldconfig' for the 2.6.26-1 sources and built a kernel without networking
any support. With the same debugging parameters on the GRUB "kernel" line
mentioned above, this was the last uncompleted initcall:
calling pci_init+0x0/0x2f
C) My guess about networking causing the problem was wrong, and it is not
clear that the PCI subsystem is causing the failure either. Since this is
a dual core machine running an SMP kernel, the process causing the lockup
is not necessarily the same one that prints the kernel message before the
freeze takes place. I tried one more kernel build before writing this bug
report: I turned off as many kernel features as I could think of,
including most of ACPI, sound, framebuffers, crypto, and lowered the output
of 'egrep "=y$" .config | wc -l" down to about 300, but after building the
kernel and trying to boot it, it still froze... with this last message:
calling pci_init+0x0/0x41
While I've been writing this, I realized that there are several other
things I could try disabling -- especially including SMP. If the freezing
process is on the other core from the one printing the last message, then
disabling SMP should reveal that. Also, I could try building from
kernel.org sources to see if that makes a difference.
I was serious (above) about helping to debug this: if you can give me
enough guidance, I have a personal interest in discovering the problem. I
can use kernel 2.6.25 on this machine for now, but not forever, and I would
like to see this problem fixed sooner than later! For now, here is some
hardware info, in case that might be helpful:
# lspci -vvnn
00:00.0 Host bridge [0600]: ATI Technologies Inc RS690 Host Bridge [1002:7910]
Subsystem: ATI Technologies Inc RS690 Host Bridge [1002:7910]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 64
00:01.0 PCI bridge [0604]: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx) [1002:7912]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 99
Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fdd00000-fdefffff
Prefetchable memory behind bridge: 00000000d8000000-00000000dfffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [44] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [b0] Subsystem: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx) [1002:7912]
00:12.0 SATA controller [0106]: ATI Technologies Inc SB600 Non-Raid-5 SATA [1002:4380] (prog-if 01)
Subsystem: Elitegroup Computer Systems Device [1019:4382]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at ff00 [size=8]
Region 1: I/O ports at fe00 [size=4]
Region 2: I/O ports at fd00 [size=8]
Region 3: I/O ports at fc00 [size=4]
Region 4: I/O ports at fb00 [size=16]
Region 5: Memory at fe02f000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [70] SATA HBA <?>
Kernel driver in use: ahci
00:13.0 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI0) [1002:4387] (prog-if 10)
Subsystem: Elitegroup Computer Systems Device [1019:2621]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fe02e000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:13.1 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI1) [1002:4388] (prog-if 10)
Subsystem: Elitegroup Computer Systems Device [1019:2621]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 4 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at fe02d000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:13.2 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI2) [1002:4389] (prog-if 10)
Subsystem: Elitegroup Computer Systems Device [1019:2621]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 4 bytes
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fe02c000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:13.3 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI3) [1002:438a] (prog-if 10)
Subsystem: Elitegroup Computer Systems Device [1019:2621]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 4 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at fe02b000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:13.4 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI4) [1002:438b] (prog-if 10)
Subsystem: Elitegroup Computer Systems Device [1019:2621]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 4 bytes
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fe02a000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:13.5 USB Controller [0c03]: ATI Technologies Inc SB600 USB Controller (EHCI) [1002:4386] (prog-if 20)
Subsystem: Elitegroup Computer Systems Device [1019:2621]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin D routed to IRQ 19
Region 0: Memory at fe029000 (32-bit, non-prefetchable) [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [e4] Debug port: BAR=1 offset=00e0
Kernel driver in use: ehci_hcd
00:14.0 SMBus [0c05]: ATI Technologies Inc SBx00 SMBus Controller [1002:4385] (rev 13)
Subsystem: Elitegroup Computer Systems Device [1019:2621]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: I/O ports at fa00 [size=16]
Region 1: Memory at fed00000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [b0] HyperTransport: MSI Mapping Enable- Fixed+
Kernel driver in use: piix4_smbus
00:14.1 IDE interface [0101]: ATI Technologies Inc SB600 IDE [1002:438c] (prog-if 8a [Master SecP PriP])
Subsystem: Elitegroup Computer Systems Device [1019:2621]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at f900 [size=16]
Capabilities: [70] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
Address: 00000000 Data: 0000
Kernel driver in use: ATIIXP_IDE
00:14.2 Audio device [0403]: ATI Technologies Inc SBx00 Azalia [1002:4383]
Subsystem: Elitegroup Computer Systems Device [1019:2621]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 4 bytes
Interrupt: pin ? routed to IRQ 16
Region 0: Memory at fe020000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Kernel driver in use: HDA Intel
00:14.3 ISA bridge [0601]: ATI Technologies Inc SB600 PCI to LPC Bridge [1002:438d]
Subsystem: Elitegroup Computer Systems Device [1019:2621]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:14.4 PCI bridge [0604]: ATI Technologies Inc SBx00 PCI to PCI Bridge [1002:4384] (prog-if 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fdc00000-fdcfffff
Prefetchable memory behind bridge: fdf00000-fdffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: [80] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map [1022:1101]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller [1022:1102]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control [1022:1103]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: [f0] Secure device <?>
Kernel driver in use: k8temp
01:05.0 VGA compatible controller [0300]: ATI Technologies Inc RS690 [Radeon X1200 Series] [1002:791e]
Subsystem: Elitegroup Computer Systems Device [1019:2621]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 5
Region 0: Memory at d8000000 (64-bit, prefetchable) [size=128M]
Region 2: Memory at fdee0000 (64-bit, non-prefetchable) [size=64K]
Region 4: I/O ports at ee00 [size=256]
Region 5: Memory at fdd00000 (32-bit, non-prefetchable) [size=1M]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
01:05.2 Audio device [0403]: ATI Technologies Inc Radeon X1200 Series Audio Controller [1002:7919]
Subsystem: ATI Technologies Inc Radeon X1200 Series Audio Controller [1002:7919]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 4 bytes
Interrupt: pin B routed to IRQ 19
Region 0: Memory at fdefc000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Kernel driver in use: HDA Intel
02:05.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8110SC/8169SC Gigabit Ethernet [10ec:8167] (rev 10)
Subsystem: Elitegroup Computer Systems Device [1019:8167]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (8000ns min, 16000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at de00 [size=256]
Region 1: Memory at fdcff000 (32-bit, non-prefetchable) [size=256]
[virtual] Expansion ROM at fdf00000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: r8169
-- Package-specific info:
-- System Information:
Debian Release: lenny/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.25-7.080720.fileserver.uvesafb (SMP w/2 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.26-1-amd64 depends on:
ii debconf [debconf-2.0] 1.5.22 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92e tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
linux-image-2.6.26-1-amd64 recommends no packages.
Versions of packages linux-image-2.6.26-1-amd64 suggests:
ii grub 0.97-44 GRand Unified Bootloader (Legacy v
pn linux-doc-2.6.26 <none> (no description available)
-- debconf information:
linux-image-2.6.26-1-amd64/postinst/create-kimage-link-2.6.26-1-amd64: true
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.26-1-amd64/postinst/kimage-is-a-directory:
linux-image-2.6.26-1-amd64/preinst/bootloader-initrd-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/postinst/old-initrd-link-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/preinst/initrd-2.6.26-1-amd64:
linux-image-2.6.26-1-amd64/postinst/old-system-map-link-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/postinst/depmod-error-initrd-2.6.26-1-amd64: false
linux-image-2.6.26-1-amd64/preinst/overwriting-modules-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/preinst/elilo-initrd-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/postinst/bootloader-error-2.6.26-1-amd64:
linux-image-2.6.26-1-amd64/preinst/abort-install-2.6.26-1-amd64:
linux-image-2.6.26-1-amd64/preinst/lilo-initrd-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/postinst/depmod-error-2.6.26-1-amd64: false
linux-image-2.6.26-1-amd64/prerm/removing-running-kernel-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/prerm/would-invalidate-boot-loader-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/postinst/bootloader-test-error-2.6.26-1-amd64:
linux-image-2.6.26-1-amd64/preinst/abort-overwrite-2.6.26-1-amd64:
linux-image-2.6.26-1-amd64/postinst/old-dir-initrd-link-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/preinst/lilo-has-ramdisk:
linux-image-2.6.26-1-amd64/preinst/failed-to-move-modules-2.6.26-1-amd64:
Reply to: